Escolar Documentos
Profissional Documentos
Cultura Documentos
COLOR MONITOR
Chassis Model
AN15V* 551V, 551S
56V, 56E
SERVICE Manual
2. Product Specifications
5. Troubleshooting
8. Block Diagram
9. Wiring Diagram
AN15V* 1-1
1 Precautions
CONFIDENTIAL
1-2 Servicing Precautions
WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances
create conflict between the servicing precautions and safety precautions, always
follow the safety precautions.
WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions.
WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the cabinet, 5. Check the insulation between the blades of the AC
and should be followed closely. plug and accessible conductive parts (examples:
2. Always unplug the unit’s AC power cord from the metal panels, input terminals and earphone jacks).
AC power source before attempting to: (a) remove 6. Insulation Checking Procedure: Disconnect the
or reinstall any component or assembly, (b) power cord from the AC source and turn the power
disconnect PCB plugs or connectors, (c) connect all switch ON. Connect an insulation resistance meter
test components in parallel with an electrolytic (500 V) to the blades of the AC plug.
capacitor. The insulation resistance between each blade of the
3. Some components are raised above the printed AC plug and accessible conductive parts (see
circuit board for safety. An insulation tube or tape above) should be greater than 1 megohm.
is sometimes used. The internal wiring is 7. Never defeat any of the +B voltage interlocks. Do
sometimes clamped to prevent contact with not apply AC power to the unit (or any of its
thermally hot components. Reinstall all such assemblies) unless all solid-state heat sinks are
elements to their original position. correctly installed.
4. After servicing, always check that the screws, 8. Always connect a test instrument’s ground lead to
components and wiring have been correctly the instrument chassis ground before connecting
reinstalled. Make sure that the area around the the positive lead; always remove the instrument’s
serviced part has not been damaged. ground lead last.
1. Immediately before handling any semiconductor 6. Do not remove a replacement ESD from its
components or assemblies, drain the electrostatic protective package until you are ready to install it.
charge from your body by touching a known earth Most replacement ESDs are packaged with leads
ground. Alternatively, wear a discharging wrist- that are electrically shorted together by conductive
strap device. To avoid a shock hazard, be sure to foam, aluminum foil or other conductive materials.
remove the wrist strap before applying power to 7. Immediately before removing the protective
the monitor. material from the leads of a replacement ESD,
2. After removing an ESD-equipped assembly, place it touch the protective material to the chassis or
on a conductive surface such as aluminum foil to circuit assembly into which the device will be
prevent accumulation of an electrostatic charge. installed.
3. Do not use freon-propelled chemicals. These can Caution: Be sure no power is applied to the
generate electrical charges sufficient to damage chassis or circuit and observe all
ESDs. other safety precautions.
4. Use only a grounded-tip soldering iron to solder or
8. Minimize body motions when handling
desolder ESDs.
unpackaged replacement ESDs. Motions such as
5. Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from
solder removal devices not classified as “anti-static” a carpeted floor can generate enough static
can generate electrical charges sufficient to damage electricity to damage an ESD.
ESDs.
9. Indicates ESDs on the Schematic Diagram in
this manual.
1-2 AN15V*
CONFIDENTIAL
2 Product Specifications
2-1 Specifications
Item Description
Dimensions (W x D x H)
With Base 14.01 x 14.92 x 14.54 Inches (356 x 379 x 369.5 mm)
Weight (Net/Gross) 11.5 kg (25.35 lbs) / Standard : 13.3 kg (29.32 lbs), Special : 13.4 kg (29.54 lbs)
• Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
AN15V* 2-1
2 Product Specifications
CONFIDENTIAL
2-2 Pin Assignments
Sync
Type Separate Macintosh
Pin No.
1 Red GND-R
2 Green Red
3 Blue H/V Sync.
4 N-C Sense 0
5 GND (DDC Return) Green
6 GND-R GND-G
7 GND-G Sense 1
8 GND-B Reserved
9 N-C Blue
10 GND-Sync./Self-Test Sense 2
11 N-C GND
12 DDC Data V-Sync.
13 H-Sync. GND-B
14 V-Sync. GND
15 DDC Clock H-Sync.
15
2-2 AN15V*
2 Product Specifications
CONFIDENTIAL
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
Separate Sync
Horizontal Vertical
Video
Video Video
Video
CC DD E E Q Q RR S S
Sync
Sync Sync
Sync
BB PP
AA O O
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
AN15V* 2-3
2 Product Specifications
CONFIDENTIAL
Memo
2-4 AN15V*
CONFIDENTIAL
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
AN15V* monitor.
WARNING: This monitor contains electrostatically sensitive devices. Use with caution when
handling these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. To remove the Rear Cover, you must use the special opening jig tool.
3-1-1 Before making Disassembly 4. Push the Opening jig each groove along the
1. Disconnect or power cord from the monitor. top of the monitor till it makes a “ttak” sound.
(2 grooves : Left and Right, Make sure each
2. With a pad beneath it, stand the monitor on its snap is disengaged.)
front with the screen facing downward and
the base close to you.
3-1-2 Cabinet Disassembly
1. Remove the Stand from the monitor.
(Refer to Stand manual)
2. Remove 2 screws on the Rear cover.
Figure 3
5. Pull the Rear Cover up off the monitor.
Figure 1
3. Incline the monitor by lifting the rear of the
monitor.
Figure 4
Figure 2
AN15V* 3-1
3 Disassembly and Reassembly
CONFIDENTIAL
6. Remove the Shield.(TCO 95) 3-1-4 Removing the Main PCB
1. Complete all previous steps.
2. Disconnect the Degaussing Coil at CN603 on
the Main PCB.
3. Disconnect all easily accessible ground wires
on the PCB and Bottom Chassis.
4. Disconnect the DY connector at the CN404
connector on the Main .
5. Using the jig, release the snaps (2) connecting
the Front Cover and the PCB then lift up the
Bottom to separate the two Shield.
Figure 5
3-2 Reassembly
3-2 AN15V*
CONFIDENTIAL
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions
are given for adjustments using the monitor Interface Board Ver. 1.1 and software (Softjig).
AN15V* 4-1
4 Alignment and Adjustments
CONFIDENTIAL
4-2 Display Control Adjustments
4-2-1 HIGH VOLTAGE 4-2-3 (a-2) HORIZONTAL SIZE ADJUSTMENT
Signal: 800 x 600 (54 KHz/85 Hz) Use control bar after selecting “H-SIZE” in left
Display image: Full White Pattern menu to adjust the horizontal size of the display
Contrast: Maximum pattern to 267 mm . (Tolerance: ± 4 mm.)
Brightness: Maximum
Limit: 25.0 kV ± 0.2 kV 4-2-3 (b) VERTICAL SIZE ADJUSTMENT
Measure the hight voltage level at the anode cap. CONDITIONS
High voltage should be within the limit as above. Scanning frequency: 54 KHz/85 Hz
Display image: Crosshatch pattern
4-2-2 CENTER RASTER Brightness: Maximum
Adjust VR401 so that the back raster comes to the Contrast: Maximum
center when you apply each basic mode.
Use control bar after selecting “V-SIZE” in left
SCREEN VOLTAGE ADJUSTMENT menu to adjust the vertical size of the display
❈ This can only SDI CRT conditions. pattern to 200 mm. (Tolerance: ± 4 mm.)
Signal: 800 x 600 (54 KHz/85 Hz)
Display image: Don’t care 4-2-3 (c) HORIZONTAL POSITION ADJUSTMENT
Contrast: Minimum CONDITIONS
Brightness: Minimum Scanning frequency: 54 KHz/85 Hz
Limit: 480 ± 10V Display image: Crosshatch pattern
Adjust screen VR of T501.
Use control bar after selecting “H-POSITION” in
4-2-3 Centering left menu to center the horizontal image on the
Centering means to position the center point of raster.
the display in the middle of the display area.
Horizontal size and position and vertical size and 4-2-3 (d) VERTICAL POSITION ADJUSTMENT
position control the centering of the display. CONDITIONS
Adjust the horizontal size and vertical size to their Scanning frequency: 54 KHz/85 Hz
optimal settings: 267 mm (H) x 200 mm. Display image: Crosshatch pattern
Adjust the horizontal position and vertical Use control bar after selecting “V-POSITION” in
position to ≤ 5.0 mm of the center point of the left menu to center the vertical image on the
screen. raster.
4-2 AN15V*
4 Alignment and Adjustments
CONFIDENTIAL
4-2-4 (a) HORIZONTAL LINEARITY ADJUSTMENT Use control bar after selecting “PINBALANCE” in
CONDITIONS left menu to optimize the image.
Scanning frequency: 54 KHz/85 Hz
Display image: Crosshatch pattern
4-2-7 Parallelogram Adjustment
Brightness: Maximum CONDITIONS
Contrast: Maximum Scanning Frequency: 54 KHz/85 Hz
To adjust the Horizontal Linearity, refer to Table Display image: Crosshatch pattern
4-1 for the tolerance range. Brightness: Maximum
Increase or decrease H_LIN to optimize the Contrast: Maximum
image.
Use control bar after selecting “PARALLEL” in
4-2-4 (b) VERTICAL LINEARITY ADJUSTMENT left menu to make the image area rectangular.
CONDITIONS
Scanning frequency: 54 KHz/85 Hz
Display image: Crosshatch pattern
Brightness: Maximum
Contrast: Maximum 4 mm
To adjust the Vertical Linearity, refer to Table 4-1 Figure 4-6. Parallelogram
for the tolerance range.
Use control bar after selecting “V-LINEARITY
4-2-8 Side Pincushion Adjustment
BAL” in left menu to optimize the image. CONDITIONS
4-2-5 Trapezoid Adjustment Scanning frequency: 54 KHz/85 Hz
Display image: Crosshatch pattern
CONDITIONS
Scanning frequency: 54 KHz/85 Hz Use control bar after selecting “PINCUSHION” in
Display image: Crosshatch pattern left menu to straighten the sides of the image area.
Brightness: Maximum | C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.
Contrast: Maximum C2
Use control bar after selecting “TRAPEZOID” in
left menu to make the image area rectangular.
| A – B | < 4 mm
D1 D2
A A
C1
AN15V* 4-3
4 Alignment and Adjustments
CONFIDENTIAL
4-3 Color Adjustments
CAUTION : Check below condition before color 4-3-2 (b) WHITE BALANCE ADJUSTMENT
adjustment Video signal : Analog 0.7 CONDITIONS
Vp-p (at 75 Ω)
Scanning frequency: 54 KHz/85 Hz
Sync : TTL level (H, V seperate
Display image: White box pattern
signal)
Brightness: 0.06ft-L at Back Raster
* Select “Color” in Softjig menu for color adjustment. Pattern Display
Contrast: Maximum
4-3-1 Color Coordinates (Temperature)
1. Use control bar after selecting “RED GAIN”,
Color temperature is a measurement of the “GREEN GAIN” and “BLUE GAIN” to adjust
radiant energy transmitted by a color. For the luminance to 50 ft-L with the color
computer monitors, the color temperature refers coordinates ranged for
to the radiant energy transmitted by white. Color 9300K to x = 0.283 ± 0.015, y = 0.298 ± 0.015.
coordinates are the X and Y coordinates on the
chromaticity diagram of wavelengths for the
visible spectrum.
1/3H-1/2H
4-4 AN15V*
4 Alignment and Adjustments
CONFIDENTIAL
Display image: Back raster pattern 4-3-4 Focus Adjustment
Full White Pattern
X-Y Coordinates: x = 0.283 ± 0.015, CONDITIONS
y = 0.298 ± 0.015 Scanning frequency: 54 KHz/85 Hz
ABL Luminance Refer to 4-3-2(c) (800 x 600)
Brightness: Maximum Display image: “H” character pattern
Contrast: 5 ft-L, 24 ft-L Brightness: Cut off point
Contrast: Maximum
1. Check whether the color coordinates of the
back raster satisfy the above spec. PROCEDURE
If they do not, return to 4-3-2 (a) and readjust 1. Adjust the Focus VR on the FBT to display the
all settings. sharpest image possible.
2. Display a full white pattern. 2. Use Locktite to seal the Focus VR in position.
AN15V* 4-5
4 Alignment and Adjustments
CONFIDENTIAL
Memo
4-6 AN15V*
CONFIDENTIAL
5 Troubleshooting
5-1 Parts Level Troubleshooting
Yes
Chirping noise exists? Check and replace IC601.
No
No
Yes
Yes
No
Operate normally? Replace Main board.
Yes
Verify voltages.
Done.
AN15V* 5-1
5 Troubleshooting
CONFIDENTIAL
5-1-2 DPMS Failure
No
LED blinks? Check IC201 Pin 40. CH1 P-P = 100 V CH1 RMS = 325.8 V
Yes
Yes
Q602 Base No
Refer to 5-1-1 No Power Supply.
voltage exists?
Yes
Done
5-2 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-1-3 H_Deflection Failure
Yes Yes
WAVEFORMS
Check IC605.
3 5.00 V (IC605, #28)
Yes
Yes
Check S1 ~ S2 signal.
Yes
AN15V* 5-3
5 Troubleshooting
CONFIDENTIAL
5-1-5 H_Lin. Failure Check and replace T402
Yes
Q402 Gate output duty varies with No Check some parts around Q402,
different B_Drv DAC values? IC605 Pin 4 ~ 6.
Yes
5-4 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-1-8 Side Pin or Trap Failure
No WAVEFORMS
7 IC605 Pin 24 output exists? Check and replace IC605.
7 1.00 V (IC605, #24)
Yes
No
Replace IC605.
AN15V* 5-5
5 Troubleshooting
CONFIDENTIAL
5-1-10 V Deflection Failure
No WAVEFORMS
13V and –10V lines are on? Refer to 5-1-1 No Power Supply
8 1.00 V (IC605, #23)
Yes
No
8 IC605 Pin 23 output exists? Check and replace IC605.
Yes
Yes
Yes
5-6 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-1-12 High Voltage Failure
No
10 Q402 Gate driving pulse exists? Check and replace Q401, Q417.
Yes
CH1 P-P = 2.00 V CH1 RMS = 5.868 V
No Check and replace Q402, D401
11 Q402 Drain pulse exists?
Check 50V line and L402. 10 5.00 V (Q402, Gate)
Yes
Done
Yes
Check CN102.
No
T501 Pin 8 output exists? Check and replace T501.
Yes
Yes
Done
AN15V* 5-7
5 Troubleshooting
CONFIDENTIAL
5-1-14 Dynamic Focus Failure (This comonly TSB CRT)
No WAVEFORMS
12 T502 Pin 6 output is right? Replace the C432.
12 50.0 V (T502, #6)
Yes
No
13 T502 Pin 1 input is right? Check and replace T502.
Yes
CH1 P-P = 50.0 V CH1 RMS = 75.6 V
Check the connection between FBT
Focus pin and CRT Socket PCB.
13 100 V (T502, #1)
5-8 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-1-15 No Video
Yes
Yes
Yes
Change CRT.
Done.
AN15V* 5-9
5 Troubleshooting
CONFIDENTIAL
5-1-16 Micom Failure
No WAVEFORMS
IC201 Pin 11 input voltage is 5V? Check Q608.
17 2.00 V (IC201, #13, 14)
Yes
Yes
No
IC201 Pin 18 input is right? Check and replace IC201 and R206.
Yes
No
All in/output values are right? Replace IC201.
Yes
Done
5-10 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-1-17 OSD Failure
WAVEFORMS
Check CN102 and connector Assy.
18 2.00 V (IC101, #32)
Yes
No
19 IC101 Pin 1 input is right? Check CN102 Pin 8.
19 2.00 V (IC101, #1)
Yes
Yes
Yes
Done
AN15V* 5-11
5 Troubleshooting
CONFIDENTIAL
5-1-18 User Control Failure
Yes
Check IC201.
No
RL601 operation is right? Check D-coil and TH601.
Yes
No
Q601 base input is right? Check and replace Q601.
Yes
No
IC201 Pin 4 output is right? Check and replace IC201.
Yes
Done
5-12 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-2 General Troubleshooting
5-2-1 No Picture
No
LED blinks? Refer to 5-2-2 Shut down.
Yes
No
LED is green color? Check Micom.
Yes
No
Blinking LED’s? Check power supply.
Yes
No
Yes
Video failure? Check Video board.
No
Done
AN15V* 5-13
5 Troubleshooting
CONFIDENTIAL
5-2-3 Missing Color
Yes
CH1 P-P = 10.0V CH1 RMS = 17.02V
Proper DC voltage is No Check IC101 Pin 17, 20 and 23.
on all cathodes? Check IC104.
Yes
No
G2 voltage is right? Check T501.
Yes
No
Heater voltage is right? Check D608, Q604 and T601.
Yes
No
G1 voltage is right? Check D504, Q502 and T501.
Yes
Replace CRT.
Done
5-14 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-2-4 Visible Retrace
WAVEFORMS
Check white balance adjustment.
22 5.00 V (Q502, Collector)
No
G2 voltage is right? Check T501.
Yes
No
Blank pulse is on Pin 3 of IC605? Check IC605.
23 50.00 V (CRT Socket, G1)
Yes
V_FLB pulse is on No
22 Check Q502.
Collector of Q502?
Yes
Yes
Done
AN15V* 5-15
5 Troubleshooting
CONFIDENTIAL
5-2-5 Unsynchronized Image
No
Signals are right? Check Video Cable.
Yes
Yes
Yes
Done
5-16 AN15V*
5 Troubleshooting
CONFIDENTIAL
5-2-6 Misconvergence
No
Readjust convergence.
No
Done
AN15V* 5-17
5 Troubleshooting
CONFIDENTIAL
5-2-7 Poor Focus
No
(Toshiba CRT)
Yes
(SDI CRT)
Degaussing
Yes
Purity is right? Done
No
No
Degaussing circuit is right? Refer to 5-1-19 Degaussing Failure.
Yes
5-18 AN15V*
CONFIDENTIAL
6 Exploded View and Parts List
6-1 AN15VS
AN15V* 6-1
6 Exploded View & Parts List
CONFIDENTIAL
6-2 AN15VT
6-2 AN15V*
CONFIDENTIAL
7 Electrical Parts List
7-1 Main PCB Parts
Loc. No. Code No. Description Specification Remarks
AN15V* 7-1
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-2 AN15V*
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
AN15V* 7-3
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-4 AN15V*
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
AN15V* 7-5
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-6 AN15V*
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
AN15V* 7-7
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-8 AN15V*
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
AN15V* 7-9
7 Electrical Parts List
CONFIDENTIAL
7-2 Video PCB Parts
Loc. No. Code No. Description Specification Remarks
7-10 AN15V*
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
AN15V* 7-11
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-12 AN15V*
7 Electrical Parts List
CONFIDENTIAL
7-3 Others
Loc. No. Code No. Description Specification Remarks
AN15V* 7-13
7 Electrical Parts List
CONFIDENTIAL
Loc. No. Code No. Description Specification Remarks
7-14 AN15V*
CONFIDENTIAL
8 Block Diagrams
AN15V* 8-1
8 Block Diagrams
CONFIDENTIAL
Memo
8-2 AN15V*
9-1
CONFIDENTIAL
15 PIN
D-SUB
refer to pin
assignment
of
product spec.
9 Wiring Diagram
AN15V*
9 Wiring Diagrams
CONFIDENTIAL
Memo
9-2 AN15V*
CONFIDENTIAL
10 Schematic Diagrams
10-1 Main Part Schematic Diagram
CN202
slcon7p
1
2
HS_IN 1
EY301
3
VS_IN
EY302
4 -10V 13V_1 13V_2 1
DDCDATA
5V
5
DDCCLK IC300
TDA9302H
HS301
BH62-00003A
9
6 S_RASTER 50V
1 2 3 4 5 6 7
7 R667
1
1/4W
D624
1N4148
R308
C306 C307 C304 R514
C305 1.5
470UF 220UF 220nF 1/2W
470UF 1/2W
35V 100V 12K
16V 16V MMP
ZD205 ZD201 ZD202 ZD203 ZD204 D618
UZ6.2BSB UZ5.1BSB UZ5.1BSB UZ5.1BSB UZ5.1BSB UZ6.2BSB DY_V2
R317
D303 R676 47K
C Q303
70V 6.3V 1N4002GP 1K 1/6W
B KSC945-Y
1/2W V_MUTE D505
V_OUT
1N4148
E
R313 R314 C315 C308 DY_V1
9.1K 24K 3.3nF 6.80NF
CN201
C213 C214 1/6W 1/6W 100V 100V V-DY
P D506
slcon13p 100nF 100uF 5V P
Q502 1N4148
1 100V 16V
R309 2N6520
P IC202 5.6K R310 E
2
KS24C041-C
R664
470
VREF
C316
R312
R311
1/4W
1.2
2W
V_BLK B
22
R229 2.7K MF
3 1 8 1/4W 100nF 390 MO R316 C
1/4W
2 7 100 50V 1/4W 5.6K
MF
4 3 6 1/6W MO MF 1/6W CN502
G1 IICCLK
12V 4 5 R515 slcon3p
5 R300 C300 R307 ZD301 22K -140V
IICDATA 62K
68 10NF UZ5.1BSB 1/2W
3
R220 1/4W 1/6W
6 100V
100 MF P CN501
1/6W R509 R508 R522 R513
7 VS_OUT 330K 330K 330K SNAME
47K 1 D504
1/2W 1/2W 1/2W TP501 TVR10G
8 1/2W
1
ACL SIZE_REG
G1
9 R523
IICDATA R516 D509
180K
27K 1N4148
10 1/2W
IICCLK ZD207 ZD206 1/2W C509 ACL
OSD_5V 2.2uF
UZ6.2BSB UZ6.2BSB
11 HS_OUT 250V D510
C514 C515 C516 C517 1N4148
12 330pF 330pF 330pF 330pF ADJ_ACL
500V 500V 500V 500V
13 ZD208 R529
AFC 1K
UZ5.1BSB 12V R674 12V
C204 1 EY501 10K 1/8W
10nF HS501 EYE2.2 1/8W
100V R470 BH62-00002A
IC605 ---------
10K D410
5V P C R677 1 EY502
1/6W STV6888 BD403 Q403 1K 1N4148 EYE2.2
B
BFS3557AOLS1 KSC945-Y BD406 1/8W C428
32 E BFS3557AOLS1 10uF 1 EY503 R530
VFOCUS HSYNC 1 T501_1 R526
C410 B HS_OUT 50V 100K
B 5Kohm EYE2.2
100uF 36K
R301 4.7K 1/8W VR401 HFL1327XD-RC 1/4W
16V R224 56 1/8W D511 1/4W
31 E MF
R201 IICDATA VSYNC 2 1N4148 MF
SDA VS_OUT R678 C445
KSA733-Y
10K 7 V_REG
C206 10K Q499 B 100 10uF 8
C201 1/8W R225 56 1/8W
100nF R236 R222 R221 R219 30 C 1/6W 50V
220UF R202 IC201 IICCLK HUNLOCK 3 V_BLK
10K 4.7K 4.7K 10K SCL C510
50V 16V 1/6W R218 R524
MO 1/8W 1/8W 1/8W 1/8W 6 9 56nF 130K
KS88C6232N 100 C402 C310 D411 100V
1 S1 IIC_DATA
42
1/6W 3 29
VCC FC1 4 100nF
63V MP
1nF
50V 12V 12V 50V 1N4148
11 AFC
P
1/8W
S1 IICDATA 5 10
S2 2 S2 IIC_CLK
41
IICCLK
B_DRV
28 BOUT PLL2C 5 C404
10nF
10 C407
150uF
R217 4
3 S3 40 100V P 63V 11
LED 100 D512
S3
4 DEGAUSS 39
R223
1/6W 5V
4 27
GND C0 6
C403
R407
2.7K
R408
100
RGP02-12(T)
DEGAUSS POWER_KEY 820pF 1/2W 2W L402 3
270 OP201 D401 12
38 50V MO 120uH
OFF_1 5 OFF_1 1/6W LTL-10233W 26 HOUT HGND 7 Q401 UF4004 D502
KEY3 H_DRV MO
KSC945-Y C RGP02-12(T)
OFF_2 37 R404 7V B EY500 2 13
6 OFF-MODE KEY2 R411 Q402
25 8 5.6K C409 C512 EYE1.5 1
S_RASTER
R200 56 1/8W
7 SELFRASTER KEY1
36 7 XRAY R0
1/4W C462 E
12
1/4W
IRF630 D
C408
680NF
250V
10nF
1KV EY504 1 14
330pF
24 9 MF 10nF 100V P B_DRV G MPS EYE1.5
8 35 CN604 EW_OUT 500V 1 15
V_MUTE NC MODEL-SEL EWOUT PLL1F E R406 S HS402
slcon2p
34 1 R302 100 1/6W 22K EY505 1
9 NC AVREF SCREEN
23 10 B 1/6W R415 D402 EYE1.5
ZD211 R405 C461
17 10
NC GND
33 UZ6.2BSB 2
V_OUT
C301 100V
VOUT HPOS
2.2K 1/8W
4.7uF 50V
Q420
KSA733-Y
C 1.5K UF4004
EY506 1
FOCUS
C212 2W
C211 150nF P 11 EYE1.5
11 32 22 R501 MO H/V
5V NC 1nF 100pF VCAP HVFOCUS 6.8K
50V 50V C463 B_SENSE
C202 12 31 1/6W EY507 1
GND HSYNC_IN HS_IN
8 1uF 50V
Q1
29 470nF MP EYE1.5
C203 14 20 HREF 13 1nF R416 330 SK501
15K 15K X-IN VSYNC_OUT VS_OUT VAGC D513 1/4W
22pF 50V 150K 2W S-23(1KV),5MM
1/6W 1/6W X201 VREF 1N4148
50V 15 28 C303 1/2W EY509 1 MO
TEST HSYNC_OUT HS_OUT 47uF EYE1.5
19 COMP 14
VRB
16 27 16V
DDCDATA DDCDATA CLAMP C541 D508 C502 R520
R208 56 1/8W R207 56 1/8W D501
17 26 R214 1K 1/8W 18 15 2.2nF R510 1N4148 10uF
DDCCLK DDCCLK ADJ_ACL V_REG VEHT REGIN 22K 1N4148
ADJ_ACL 100V 100K 16V EY510 1
1/6W BD410 BD411
18 RESET MODE_REG
25 R668 1K 1/8W
MODE_REG
12V
17 16
P 1/8W
BFS3557AOLS1 BFS3557AOLS1
EYE1.5 C513
1nF
13
R205 10K 1/8W HEHT ISENSE
ZD209 UZ36B 19 24 R235 10K 1/8W C501 F/S Test Point B B EY511 1 500V
50V_SENSE LATCH MODE_SIZE MODE_SIZE D302 R500
EYE1.5
1N4148 1M 22nF
20 23 R213 10K 1/8W R503
TILT TILT SIZE-ADJ R327 1/6W 100V R502
SIZE_ADJ 10K EY512
390K P R504 1
1/4W MF
4
R209 10K 1/8W 1/8W 15K 39K EYE1.5
21 22 1/6W
SUB_SIZE R445
1/6W
R206 C215 D201 R212 10
ZD210 1N4148 R328 C503
C205 1M 100pF 3.3K 1/2W
UZ4.7BSA 100nF B_SENSE R506
1uF 1/6W 50V 1/8W 150K R481 R507
1/6W 50V R480 12K C505 T502
50V 22K 10K
33K 1/4W 220nF EE-1916
C406 1/6W 1/4W
1/8W MF 50V
2.7nF MF TSB CDT
100V S3
C210 C207 C216 C209
5
13V 50V P R505 L403 C434
1uF 1uF 4.7uF 4.7uF C624 R623
2.2K 12V 12V 100PF
50V 50V 50V 50V 2.2nF 91K 7.1MH
500V
OP202 1/4W
100V 1/4W R446
LTV817M-SM P MF MF
COL
ANODE 68
R436 R438 1/2W C433
C605
22nF
C606
10nF
R606
1K
C610
100uF C628 R401
12V
D414
1N4148
Q415
2.2K
1/8W Q416
2.2K
1/8W
12 10nF
250V MP
CATHODE
EMT C625 MODE_REG C C
100V 100V R604 1/8W 16V 10nF 47K KSP42 KSP42
R620 15nF R624 1/4W R419 R461
P P 1.5K 500V B B
220K 100V 6.8K MF 180K 68K
1/8W 1/6W 1/6W 1/6W 1/6W S2 S1
P MODE_SIZE R452 R453 C431
SIZE_REG E E D413 C432
10K 10K 300nF 22nF
TVR10G
R450 R418 250V 250V
R608 K IC602 120K 3.9K MPS MP
220 TL431CLP Q406
CN603 1/4W 1/6W
slcon3p 1/4W R MF KSA733-Y
13V_1 DEGAUSS H : OFF MODE R625 R420
SIZE_ADJ
SW601 A 2.4K 150K
L : NORMAL R613 Q602 D415 C430
3 JPS1275 1/4W E E 1/4W
2K KSC945-Y C427 370nF
D-COIL
EY606 S78DL05
B
C419 UF4004 5.2nF 5 2
GT604 GT603 R610 C418
IN OUT 50V 4.4nF 630V
180K D606 T601 C623 2.2nF
B
1.6KV
2
D2SBA60
1
SCK-083
1 2 CC
1
EER39*42mm
18
D612
TVR10G
1000uF
16V
BD603
1.2UH
BD602
1.2UH
C630
470uF
C631
D627
C416
100nF OT
P
BD401
3 4 1 16V
100uF
16V 1N4148 12V 5 100V
R428
560
Option
1.2UH
D409
P
C614 3W GUR460L-5700 EYE1.5
R612
10nF 2 17 MO EY444 1
EY604 56K T401
1 EY607
500V 2W MO Q609
EYE2.2 EYE1.5 R631 EI-1916 EY445 1
KTA1281-Y R431 BD402 D408
3 16 C 1K 7 1 EYE1.5
C604 1/2W C415 1.5 1.2UH DTV56F
IC601 BD601 R425
B
4.70NF C608 D605 B R632 3W
DP104C 1.2UH D611 UF1G KSC945-Y 680 4.70UF D421 6 2
180uF UF4007 10K MO
250V 4 1 4 15 R630 C Q610 1/2W 160V 1SS244
400V B E 1/8W R426
C603 F_B DRAIN C621
47K B 10 5 3 Q404
4.70NF 47UF OFF_2
EY603 1 2 D610 UF4007(T) 1/6W 1/4W C D405 KSC5802 C
250V GND 50V R429 R430
EYE2.2 5 14 E B 470K 4
SHL C622 C634 H : NORMAL 15K DY_H4 DY_H3
1
3 5 C613 R621 H_DRV
Vcc SYNC 1000uF 10uF 1/6W 1/2W
220pF 10K L : OFF MODE C414 E Q400 EK-04 R432 E
D609 C620 16V 50V EY401
1KV 6 13 1/8W 470nF 22
31DF4 220uF KSC2383-Y D406
C602 63V 50V 1/2W ERD07-15
C609 C607 MUR460
150nF
33uF 100nF 7 12
275VAC
50V 50V
D420 R427
MO 13V_1 1N4148 1K
C611 8 11 1/8W
4 3 50V
D608 H-DY
1
1uF UF5404
L601 9 10
EY608 EY610
1N4148
1 2 EYE1.5 EYE1.5
R663 D628
C601 R607 D604 S-Correction Table
C600 22K
150nF 10K UF4007 R622 CN404
1nF C616 1/4W
275VAC 3W MO 1 slcon4p
400V 2.2nF C615 1
125V 1/4W Freq [Hz] S1 S2 DY_V1
1nF C633
R600 R601 D625 E
500V 7V OSD_5V 6.3V_1 6.3V 1uF 2
330K 330K 1N4148 DY_V2
B
50V Q613
1/2W 1/2W 31 ~ 34.9 LOW LOW
BD600 C617 HS601 D616 B KTA1281-Y 3
2.2nF DY_H3
1.2UH BH62-00004A UZ6.2BSB C
125V C
FH1 D629 35 ~ 39.9 4
LOW HIGH DY_H4
1N4148 D615 B
FH_1 FUSE
13V_2 UZ6.2BSB
FUSE2P R615 E
T602 D626 40 ~ 48.9 HIGH LOW
1K Q604 D630 R617
EY602 1 BH26-30302S 1N4148
1/2W KSD1616-Y 1N4148 1.2
EYE2.2 1 5 12V
1/2W 49 ~ HIGH HIGH
1
Q614
E
EY601 1 CN601 2 B
EYE2.2 slcon3p BD605 KSC945-Y
B
4 BFS3557AOLS1
3
AFC
AC INPUT
C643 R614 C618
C612 R618
AC90V~AC264V 1nF D607 220 1000uF C626
1uF 1K
50V 1/2W 16V 100UF
1N4148 50V 1/8W
16V
AN15V* 10-1
10 Schematic Diagrams
CONFIDENTIAL
1 100 V (IC601, #1) 2 100 V (IC601, #1) 3 5.00 V (IC605, #28) 4 1.00 V (IC605, #26) 5 5.00 V (Q400, Collector) 6 5.00 V (Q408, Collector)
CH1 P-P = 100 V CH1 RMS = 350.2 V CH1 P-P = 100 V CH1 RMS = 325.8 V
7 1.00 V (IC605, #24) 8 1.00 V (IC605, #23) 9 10.0 V (IC300, #6) 10 5.00 V (Q402, Gate) 11 50.0 V (Q402, Drain) 12 50.0 V (T502, #6)
CH1 P-P = 2.00 V CH1 RMS = 7.692V CH1 P-P = 50.0 V CH1 RMS = 73.7V CH1 P-P = 50.0 V CH1 RMS = 75.6 V
13 100 V (T502, #1) 17 2.00 V (IC201, #13, 14) 22 5.00 V (Q502, Collector)
10-2 AN15V*
10 Schematic Diagrams
CONFIDENTIAL
10-2 AN15VS Normal Video Part Schematic Diagram
5V 12_1V 12V
BD105
B
C152 C103 C151
100nF 470uF 100nF
50V 16V 50V
MO MO
12V
70V
C106 C107
BD103 100nF 220uF
BD101 1.2UH,3.5X5.7MM 50V 16V
1.2UH,3.5*5.7MM
B
R124 L103 MO
BD102 82 0.47uH
1.2UH,3.5*5.7MM 1/2W
C160
R120 EY3 EY2 C108
B
47uF
30M 1 1 47uF
16V IC103 DR03 DG03 DB03
1/4W C162 C161 100V
TDA9555 1SS244 1SS244 1SS244
R105 1uF 100UF BD104 RR09 RG09 RB09
7.5K 50V 16V R130 75K 75K 75K
TDA9556
1/6W 39ohm
B
1/4W 1/4W 1/4W
GNDA
GNDP
OUT3
OUT2
OUT1
GNDS
1W
IN1
IN2
VCC
IN3
VDD
MO
C113 19
6
1
10
R108
11
IC101
5.6K 22NF
KB2551 CR04 CRT
100V 1/6W
P 32 HFLB 1uF RR10 21 M36KUK35X02(R)
1 VFLB RR08 LR01 120 OHM
31 VDD CR08 160V R_OUT
2 VSSA 1/6W 15 0.47uH POW
30 SDA 1NF HS103 EY1 EY4 EY5
3 VCO_IN_P
29 SCL 50V heat_sink 1 1 1
4 VREF1
28 VSS CG04
5 VREF
RG10 15_NOR
12V
R109 12K
16 6 VDDA
27 RCT 15 20 C163 RG08 LG01
1uF
crt_sock10p
26 GCT RR15 160V 150 G_OUT
7 10NF 6
CONT_CAP 1/6W 100 0.47uH 1/2W RED
1/6W 25 BCT 68 500V 4
8 ABL_IN
GREEN
DG01 R107 24 ROUT 1/6W 9
9 GND
BLUE
1N4148 1K C102 10 CLP_IN 23 RCLP
1/8W R101 CB04 RB10
HEATER
1/6W
1uF 3.3K 11 VCC3 22 VCC2 RB08 1uF 120 OHM
OPEN
LB01
GND1
GND2
GND
50V 12 RIN 21 GOUT CR02 160V POW B_OUT
DR01 1/8W 1/6W 120 0.47uH
G1
G2
DB01 20 GCLP RR03
1N4148 13 VCC1 1uF
1N4148 19 GND2 470
14 GIN 50V
14 15 GND1 18 BOUT C118
7
8
2
10
3
5
1
RR02 CR01 16 BIN 17 BCLP 100pF
75 100nF 50V CG08
G1 6.3V
CN101 50V 150PF 23
slcon6p MO 50V
RR01 CR03
DR02
75 33PF
1 1N4148 1/6W 50V CG01 RG15 G2
1/6W
RG02
2 100nF 68
75 R104
50V 1/6W
DR04 DG04 DB04 390
1/8W
SKR01 SKG01 SKB01
3 MO 1SS244 1SS244 1SS244 1/2W
CG03 SPARK_RA
DG02 RG01
33PF
4 1N4148 75 RG03 1
1/6W RB02 50V CB01
1/6W 560 G2
5 75 100nF
CG02 DMS-200D DMS-200D C114 C120
50V SK102
1UF 1.8nF 1nF
6 MO CB08
CB03 50V 500V 1KV
1NF
RB01 33PF R118
DB02 50V 1
75 50V 560
1N4148 1/6W 1/6W 1/8W GND
1/8W
RB03
R102 560
70V
CB02
100
1uF
1/6W ZD102 R119
50V
UZ6.2BSB 560
1/8W
IICDATA 12V
ACL
V_SYNC IICCLK
5V
AFC
RR07 RG07 RB07
18K 18K 18K
R117 C117 IC104
680 22NF LM2480NA
1/6W 100V 1 8
A H
P RR05 39K
2 7
B G
B
RG05 39K
70V 6.3V 12V BD106 3 6
1.2UH,3.5*5.7MM C F
RB05 39K 5
4
D E
G1 C115 CR06 CG06 CB06
L101 10UF 100nF 100nF 100nF
R103
100V 100V 100V 100V
100uH 390
C123 C124
1/2W
10nF 10nF
500V 100V
P
12
13
14
11
1
CN102
G1
VS_OUT
ACL
IICCLK
CLAMP
AFC
IICDATA
slcon14p
C121
100nF
50V
MO
AN15V* 10-3
10 Schematic Diagrams
CONFIDENTIAL
14 1.00 V (IC101 #12,14,16) 15 0.5 V (IC101 #18,21,24) 16 20.0 V (IC102 #9,10,11) 19 2.00 V (IC101 #1)
20 1.00 V (IC101 #18,21,24) 21 10.0 V (R,G,B, Video) 23 50.00 V (CRT Socket, G1)
10-4 AN15V*
10 Schematic Diagrams
CONFIDENTIAL
10-3 AN15VS MINI_MVT Video Part Schematic Diagram
5V 12_1V 12V
BD105
B
C152 C103 C151
100nF 470uF 100nF
50V 16V 50V
MO MO
12V
BD101
1.2UH,3.5X5.7MM 70V
C106 C107
BD103 100nF 220UF
B
1.2UH,3.5X5.7MM 50V 16V
R124
B
BD102 L103 MO
1.2UH,3.5*5.7MM 82 0.47uH
C160 1/2W
B
R120 2.7nF C108
30M 100V 47uF
C162 P IC103 DR03 DG03 DB03
1/4W 100V
TDA9556 1SS244 1SS244 1SS244
R105 1uF BD104 RR09 RG09 RB09
7.5K 50V C161 R130 75K 75K 75K
GNDS
1/6W 100UF 39ohm
GNDA
GNDP
OUT3
OUT2
OUT1
B
1/4W 1/4W 1/4W
IN1
IN2
VCC
IN3
VDD
16V 1W
MO
C113 19
6
R108
10
11
IC101
5.6K 22NF
KB2551 CR04 CRT
100V 1/6W RR10
P 1 VFLB 32 HFLB LR01
1uF
120 OHM
21 M36KUK35X02(R)
CR08 RR08 160V
2 VSSA 31 VDD 0.47uH POW R_OUT
1/6W 15
30 SDA 1NF HS103 EY1 EY4 EY5
3 VCO_IN_P
29 SCL 50V heat_sink 1 1 1
4 VREF1
28 VSS CG04
5 VREF RG10
R109 12K 15 20 1uF
12V 16 6 VDDA 27 RCT C163 RG08 LG01 150
26 GCT RR15 10NF 160V 1/2W G_OUT
7 CONT_CAP 1/6W 100 0.47uH 5 RK
1/6W 25 BCT 68 500V
8 ABL_IN 7 GK
DG01 R107 24 ROUT 1/6W
9 GND 1 BK
1N4148 1K C102 10 CLP_IN 23 RCLP RB10
1/8W R101 CB04
1/6W
1uF 3.3K 11 VCC3 22 VCC2 RB08 LB01 1uF 120 OHM
DR01 50V 1/8W 12 RIN 21 GOUT CR02 160V POW B_OUT
DB01 RR03 1/6W 120 0.47uH
1N4148 13 VCC1
20 GCLP 1uF H GND1
GND2G1G2
1N4148 470
14 GIN 19 GND2 50V 2 4 6
14 15 GND1 18 BOUT C118 3 8 15_MINI
RR02 CR01 16 BIN 17 BCLP 100pF j_c8_1p
75 100nF 50V CG08
G1 6.3V
CN101 50V 150PF 23
slcon6p MO 50V
RR01 CR03
DR02
75 33PF SKR01
1 1N4148 1/6W 50V RG15 SPARK_RA SKB01 G2
1/6W CG01
RG02
2 100nF 68
75 R104
50V 1/6W
DR04 DG04 DB04 390
1/8W
3 MO SKG01
CG03 1SS244 1SS244 1SS244 1/2W
RG01 SPARK_RA
DG02 33PF
4 75 RG03 1
1N4148 1/6W RB02 50V
1/6W CB01 560 G2
5 75 100nF
50V CG02 DMS-200D C114 C120
SK102
1UF 1.8nF 1nF
6 MO CB08
CB03 50V 500V 1KV
1NF
DB02 RB01 33PF 50V 1
1N4148 75
1/6W 50V
1/6W R118 R119 GND
560 560
1/8W RB15 DR05 DG05 DB05
1/8W
68 1N4148 1N4148 1N4148
1/6W
CLAMP
R102
100
1/8W
1/6W RB03
560
70V
CB02
1uF
50V
IICCLK
IICDATA
ACL 12V
ZD102
UZ6.2BSB
V_SYNC
5V
AFC
RR07 RG07 RB07
18K 18K 18K IC104
R117 C117 LM2480NA
680 22NF
1/6W 100V 1 8
A H
P 39K
RR05 7
2
B G
B
RG05 39K
70V 6.3V 12V BD106 3 6
1.2UH,3.5*5.7MM C F
RB05 39K 5
4
D E
G1 C115 CR06 CG06 CB06
L101 10UF 100nF 100nF 100nF
R103
100V 100V 100V 100V
100uH 390
C123 C124
1/2W
10nF 10nF
500V 100V
P
12
13
14
11
1
CN102
G1
VS_OUT
ACL
IICCLK
CLAMP
AFC
IICDATA
slcon14p
C121
100nF
50V
MO
AN15V* 10-5
10 Schematic Diagrams
CONFIDENTIAL
14 1.00 V (IC101 #13, 14, 16) 15 0.5 V (IC101 #18,21,24) 16 20.0 V (IC102, #9, 10, 11) 19 2.00 V (IC101, #1)
20 1.00 V (IC101, #18,21,24) 21 10.0 V (R,G,B, Video) 23 50.00 V (CRT Socket, G1)
10-6 AN15V*
Samsung Electronics Co.,Ltd.
416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea.
Printed in Korea
P/N : BH82-00005E-00
http://www.samsungmonitor.com (SyncMaster Worldwide)
http://www.samsung-monitor.com (SyncMaster USA)
http://www.sec.co.kr/monitor (Korea)