Escolar Documentos
Profissional Documentos
Cultura Documentos
1 (83)
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2009. All rights reserved.
2 (83)
Contents
Contents
Contents 3 Summary of changes 5 1 2 3 4 5 6 7 7.1 7.2 7.3 8 9 9.1 9.2 9.3 9.4 10 10.1 10.2 10.3 10.4 11 12 12.1 12.2 12.3 13 13.1 Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description 7 Pole Mounting Kit (VMPB) description 11 Flexi Mounting Auxiliary Bracket (FMAA) description 13 Flexi Pole Installation Kit (FPIA) description 15 Flexi Pole Mounting Kit (FPKA) description 17 Flexi Mounting Covers for Back and Front (FMCA and FMCB) description 23 Flexi System External Alarm (FSEB) description 27 Flexi System External Alarm Box (FSEB) operation 27 Flexi System External Alarm (FSEB) dimensions and weight Flexi System External Alarm (FSEB) interfaces 28 Flexi System External OVP (FSEC) description 31 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description 35 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) operation 35 Flexi Power Module (FPMA) dimensions and weight 37 Flexi Power Module (FPMA) and sub-module (FPAA and FPBA) interfaces 38 Flexi power sub-module (FPAA and FPBA) LED indications 40 Flexi Power DC/DC Module (FPDA) description 43 Flexi Power DC/DC Module (FPDA) operation 43 Flexi Power DC/DC Module (FPDA) dimensions and weight Flexi Power DC/DC Module (FPDA) interfaces 45 Flexi Power DC/DC Module (FPDA) LED indications 46 Flexi Power AC/DC sub-module (FPAB) description 47 Flexi FCIA FCIA FCIA Cabinet for Indoor (FCIA) description 51 cabinet construction 51 optional items 52 dimensions and weight 53
27
44
Flexi Cabinet for Outdoor (FCOA) description 55 Flexi Cabinet for Outdoor (FCOA) construction 55
3 (83)
13.2 13.3 14 14.1 14.2 15 15.1 15.2 15.3 16 16.1 16.2 17 17.1 17.2 17.3 18
FCOA optional items 56 Flexi Cabinet for Outdoor (FCOA) dimensions and weight
60
Flexi Mounting Shield (FMSA and FMSB) description 63 Flexi Mounting Shield (FMSA and FMSB) operation and construction 63 Flexi Mounting Shield (FMSA and FMSB) dimensions and weights 66 Flexi Mounting Kit Vertical for 2G (FMUA) description 67 Flexi Mounting Kit Vertical for 2G (FMUA) operation 67 Flexi Mounting Kit Vertical for 2G (FMUA) construction 69 Technical properties of Flexi Mounting Kit Vertical for 2G (FMUA)
71
Flexi Mounting Kit Horizontal for 2G (FMUB) description 73 Flexi Mounting Kit Horizontal for 2G (FMUB) operation and construction 73 Technical properties of Flexi Mounting Kit Horizontal for 2G (FMUB) I-HSPA Adapter description 77 Overview of I-HSPA Adapter hardware 77 Physical dimensions of the I-HSPA Adapter 79 Physical interfaces of the I-HSPA Adapter 79 Talk Conversion Kit (EMIA or EMIB) 81
74
4 (83)
Summary of changes
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Changes between issues 8-1 and 8-2 Section Flexi Pole Mounting Kit (FPKA) description updated. Section Flexi System External OVP (FSEC) description updated. Changes between issues 8-0 and 8-1 Section Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description edited. Section Flexi Mounting Auxiliary Bracket (FMAA) description added. Section Flexi Pole Mounting Kit (FPIA) description edited. Section Flexi Pole Mounting Kit (FPKA) description edited. Section Flexi System External OVP (FSEC) description edited. Information related to Flexi system external GPS mediator (FSEG) has been removed. Sections Flexi System External GPS Mediator (FSEG) operation, Flexi System External GPS Mediator (FSEG) dimensions and weight, Flexi System External GPS Mediator (FSEG) interfaces and GPS antenna removed. Term Flexi Rectifier Module replaced with Flexi Power Rectifier and information related to it updated in sections FCIA cabinet construction, FCIA optional items, and FCOA optional items. Editorial changes made.
5 (83)
Changes between issues 7-1 and 8-0 Table Dimensions and weight of the FMFA in section Flexi mounting kit for floor, wall and pole (FMFA) description edited. Figure Flexi Pole Installation Kit (FPIA) added to section Flexi Pole Installation Kit (FPIA) description. Section Flexi Pole Mounting Kit (FPKA) description edited. Section Flexi Mounting Covers for Back and Front (FMCA and FMCB) description edited. Section Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) operation edited. Section Flexi power DC/DC sub-module (FPDA) operation edited. Section FCIA cabinet construction edited. Section FCIA cabinet optional items edited. Section FCOA optional items edited. Section FCOA dimensions and weight edited. Section Physical dimensions of the I-HSPA Adapter edited. Section Physical interfaces of the I-HSPA Adapter edited. Section Talk Conversion Kit (EMIA) edited and figure Parts needed for installing Flexi EDGE BTS modules in Citytalk cabinet added.
6 (83)
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description
Flexi BTS modules are installed on the floor, wall or pole using Flexi Mounting kit for Floor, Wall and Pole (FMFA). The FMFA consists of a plinth and adapter mechanics. The plinth is required in BTS site installations without a cabinet and it provides grounding points for BTS and module grounding. The mounting principles are the following:
.
In floor mounting, the plinth is fixed directly onto the floor. To meet the Telcordia GR-63-CORE Vibrational requirements for earthquake Zone 4 requirement, the maximum number of modules in a stack is five (maximum total height 15 U). To meet the Telcordia GR-63CORE Vibrational requirements for earthquake Zone 2 requirement, the maximum number of modules in a stack is nine (maximum total height 22 U). In wall mounting, the plinth is fixed onto the wall either by using adapter mechanics or directly to the wall. The maximum number of modules per plinth is two. In pole mounting, the plinth is fixed onto a pole mounting kit (VMPB or FPKA) by using adapter mechanics. Adapters are needed to reduce the influence of non-parallel surfaces of the mounting brackets. The maximum number of modules per plinth is two. The FMFA delivery includes two fixing plates for the casings. Used in pole and wall installations, the plates are attached across two module casings on both sides of the modules. See the following figure for an isometric view of the FMFA.
7 (83)
DN7082497
Figure 1.
DN7099438
Figure 2.
Adapter mechanics
8 (83)
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description
The plinth has a back stop that prevents installing the BTS too near to a wall (40 mm). The compartment behind the front panel of the plinth is used as a storage place, for example, for seal caps. FMFA dimensions and weight The dimensions and weight of the FMFA are presented in the following table.
Table 1. Property
Height
Width
Depth
Weight
Wall configuration 4.2 kg (9.3 lbs) Floor configuration 2.9 kg (6.4 lbs)
The material of the plinth is 1.5 mm (0.06 in.) sheet metal. For installation instructions, see Installing Flexi WCDMA BTS Modules for Stack, Wall, and Pole Configurations. External connections The plinth has the following fixing interfaces:
.
ESD studs (2 pcs) Casing fixing points (4 pcs) Pole/wall adapter fixing points (6 pcs) Threads for the lifting eye bolts (4 pcs) Modules grounding (24 pcs) BTS grounding (1 pcs) Casing locking points (2 pcs)
9 (83)
Anchoring points to floor (4 main and 2 optional) Fixing plate fixing points (4 pcs)
See the following figure for the external fixing interfaces of the FMFA.
Casing fixing points Casing locking points Casing locking points Fixing holes for fixing plates
ESD Stud
DN7082504
Figure 3.
10 (83)
DN70415461
Figure 4.
See the following table for the delivery contents of the VMPB.
Table 2. Item
Pole Mounting Kit (VMPB) Mounting blocks M8x25 bolts M10x120 bolts M10x200 bolts M10x300 bolts Washers
11 (83)
See the following table for dimensions and weight of the VMPB.
Table 3. Property
Height Width Depth Weight
For installation instructions, see section Mounting the plinth on a pole in the Installing Flexi WCDMA BTS Modules for Stack, Wall, and Pole Configurations document.
12 (83)
13 (83)
DN70449903
Figure 5.
14 (83)
Flexi System External Alarm (FSEB) Flexi System External OVP (FSEC)
The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter. There are two sets of fixing points on the installation plate. The FPIA can carry the weight of 5 kg (11 lbs). For the FPIA delivery contents, see section Contents of the Flexi Pole Installation Kit (FPIA) delivery in the Installing Flexi WCDMA BTS Optional Items document.
15 (83)
DN70458657
Figure 6.
16 (83)
Bolt M8x20
Fixingpoints 64mm (2.5 in.) Fixingpoints 184mm (7.2 in.) Bolt M10X120 105 mm thread
Figure 7.
The width of the fixing points is 184 mm (7.2 in.) and 64 mm (2.5in.). There are fixing points in three sides of the FPKA. The M10 screws should be tightened to 30 Nm and the M8 screws to 20 Nm. The FPKA can carry the maximum weight of 160 kg (352.7 lbs). The delivery contents of the FPKA are listed in the following table.
17 (83)
Table 4. Item
FPKA Bracket Bolt M8 x 20 Bolt restrainer FPKA bracket strainer Bolt M10 x120 105 mm thread ISO 4762 (DIN912)
Installation with Remote Radio Heads The FPKA has room for three Remote Radio Heads (FRGG). It is possible to use three installation directions. See the following figure for the FPKA installation with three Remote Radio Heads.
18 (83)
Figure 8.
Installation with Flexi modules The FPKA has room for a maximum of four 3U Flexi modules (12U total). Two modules (or casings) can be installed on opposite sides of the FPKA. See the following figure for the FPKA Installation with four 3U modules.
19 (83)
DN70424752
Figure 9.
Installation with MetroSite 50 The FPKA supports the MetroSite 50 with two installation directions. See the following figure for the FPKA installation with MetroSite 50.
20 (83)
DN70424776
Figure 10.
21 (83)
22 (83)
Flexi Mounting Covers for Back and Front (FMCA and FMCB) description
Flexi Mounting Covers for Back and Front (FMCA and FMCB) description
Flexi mounting covers for back and front are optional 3U (FMCA) and 2U (FMCB) module covers that are required in installations without a cabinet. The primary functions of the covers are to provide protection against winddriven rain, visual protection, and mechanical protection for the cables. Furthermore, the back cover protects the installer's fingers from the rotating fans. The front cover air deflector is semi-transparent to allow assessing the status of the hardware LEDs without removing the front covers. For installation instructions, see section Installing back and front covers in the Installing Flexi WCDMA BTS Optional Items document. The FMCA and FMCB deliveries include a grounding cable. Note that it is not included in any module deliveries. The back and front covers, the safety catches and the grounding cable are illustrated in the following figure.
23 (83)
Front cover
Back cover
2 x safety catch
Grounding cable
DN7082516
Figure 11.
FMCA: 3U back cover, 3U front cover, 2 x safety catch and grounding cable
FMCA dimensions The dimensions of the FMCA are presented in the following table.
Table 5. Property
Height
Back cover
128 mm (5 in.) 446 mm (17.6 in.) 37 mm (1.5 in.)
Width
Depth
24 (83)
Flexi Mounting Covers for Back and Front (FMCA and FMCB) description
Table 6. Property
Height
Back cover
83 mm (3.3 in.) 446 mm (17.6 in.) 37 mm (1.5 in.)
Width
Depth
Table 7. Property
Length Thickness
25 (83)
26 (83)
7
7.1
7.2
27 (83)
Table 8. Property
Width
Height
94 mm (3.7 in.)
Depth
Weight
The mounting dimensions of the FSEB enclosure are 110 mm x 324 mm (4.3 in. x 12.8 in.). The material of the box is plastic.
7.3
28 (83)
ESD
Grounding point EAC M16 UltraSite and Talk swap cases BTS interconnection cable DN70283679
Figure 12.
FSEB interfaces
PWB interface The PWB interface and connectors are presented in the table below.
Table 9. Interface
EACX-I
Description
. .
12 direct alarm inputs 6 alarm outputs (ESM extension, compatible to EAC on ESM)
EACX-S
10 SMDK1/6-3.5
DC power supply for the optional fire detector Interface to the System Module, *CAN bus
29 (83)
Table 9. Interface
*EACX-II
Description
12 alarm inputs via CAN bus
*Not used in WCDMA mode. See the following figure for the FSEB PWB.
ESM EACX-II(D37) EACX-I(D37) Smoke-Detector Power X4114 EACX-S screw terminals X4104 to X4113 grounding
Not in use
DN70410509
Figure 13.
FSEB PWB
30 (83)
DN70154491
Figure 14.
31 (83)
See the following figures for the internal and external wiring of the FSEC.
Internal wiring (factory cabling) version 6Yxxxxxxxxx FSEC
VAL-MS VAL-MS 60 ST 60 ST
PE
PE
Electrical connection
GND PE
0V (+)
-48 V DN70592401
Figure 15.
32 (83)
VAL-MS VAL-MS 60 ST 60 ST
+
Cable shield
PE
PE
System/RF Module
DN70592413
Figure 16.
FSEC dimensions The dimensions of the Flexi system external OVP box are presented in the following table. The FSEC is made of aluminium.
33 (83)
Height
Depth
Weight
FSEC connectors In the FSEC, there are screw terminals for input and output cables. There are four pieces of screw terminals for AWG 2 cables and for earthing two PEs (protective earthing GND) terminals for AWG 2 cable size. A 2-meter DC cable is included in the FSEC delivery.
34 (83)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description
9
9.1
Flexi Power Module (FPMA) and submodules (FPAA and FPBA) description
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) operation
Flexi Power Module (FPMA) is an optional module. It comprises FPMA mechanics and AC and DC interfaces. The actual power sub-modules are the following:
.
Flexi Power AC/DC sub-module 200-240 V AC (FPAA) Flexi Power Battery sub-module (FPBA)
The maximum number of sub-modules in an FPMA is four. For installation instructions, see section Installing Flexi Power Module (FPMA) in the Installing Flexi WCDMA BTS Optional Items document. The FPMA is presented in the following figures.
35 (83)
Type label
DN70230045
Figure 17.
DN7084386
Figure 18.
36 (83)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description
The FPMA can support 1-phase and 3-phase AC input. The nominal input voltage is 200-240 V AC (the operating voltage range is 180 - 276 V AC). The maximum output power from the FPMA is 4kW (with 4 FPAAs). Flexi Power AC-DC sub-module (FPAA) The main function of the FPAA is to provide the BTS with nominal 48 V DC power from an AC supply. Maximum DC output power of one FPAA module is 1000 W. A nominal 48 V DC supply is intended for BTS internal use only (a nominal 48 V DC supply is not intended for 3rd party equipment because they may require lower conducted emission level than EN55022 Class A). The FPAA includes its own integrated self-controlled fan. In case the fan fails, an alarm is generated and the FPAA has to be replaced (the fan alone cannot be replaced).
Caution
Risk of thermal runaway of the battery, because temperature compensation of charging voltage is not supported. Do not connect an external lead acid battery for longer backup times to a nominal 48 V DC supply.
Flexi Power Battery sub-module (FPBA) The Flexi Power Battery Sub-Module (FPBA) is a separate optional submodule used together with the FPAA. The FPBA provides short-term battery backup time when the AC power mains is down on a Flexi BTS site. The FPBA is a lithium ion battery. The maximum DC output power from one FPBA module is 1000 W. The input power for the BTS cannot exceed the maximum output power of the installed batteries. Otherwise the batteries do not provide the BTS with the needed power during power failure.
9.2
37 (83)
Width
Weight (empty)
Weight (fully equipped with one AC/DC power module and batteries)
28 kg (61.9 lbs)
9.3
Flexi Power Module (FPMA) and sub-module (FPAA and FPBA) interfaces
FPMA front panel connectors The connectors on the FPMA front panel, their types and purposes are listed in the table below.
Type
Terminal block 2-wire DC cable 4 x multibeam 2 x M5
38 (83)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description
FPAA front panel connectors There is a stand-by switch on the front panel of the FPAA. The stand-by switch is used for switching the FPAA unit ON/stand-by. The connectors on the FPAA front panel, their types and purposes are listed in the table below.
Type
Mate-N-Lock Multi-beam power supply connector 2 x RJ-45* tri-colour LED
*for chaining **Alarm 1 (AL01): AC input failure (alarm is sent when AC input voltage is missing or it is out of range). **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, cooling fan failure, output power is low or over temperature shut down is ON). FPBA front panel connectors There is a stand-by switch on the front panel of the FPBA. The connectors on the FPBA front panel, their types and purposes are listed in the table below.
Type
Multi-beam power supply connector
39 (83)
Type
2 x RJ-45* tri-colour LED
*for chaining **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, output power is low or unit has reached end of it's life). **Unit has an input for Alarm 1 (AL01) from FPAA unit (Alarm 1 is a trigger for battery discharging).
9.4
See the following figure for the location of the FPAA LED.
40 (83)
Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA) description
LED
DN70350654
Figure 19.
FPAA LED
FPBA LED indications The FPBA LED indications are explained in the table below.
Green, blinking slowly Green, blinking fast Blinking fast between green and yellow Red, blinking fast Red
The LED's slow blinking frequency is 1 Hz (1 sec) and fast blinking frequency 2 Hz (0.5 sec). See the following figure for the location of the FPBA LED.
41 (83)
LED
DN70350678
Figure 20.
FPBA LED
42 (83)
10
10.1
Caution
Risk of thermal runaway of the battery, because temperature compensation of charging voltage is not supported. Do not connect an external lead acid battery for longer backup times to the 53-55 V DC supply.
The FPDA includes its own integrated self-controlled fan. In case the fan fails, an alarm is generated and the fan has to be replaced. For installation instructions, see section Installing Flexi Power DC/DC Module 24V FPDA in the Installing Flexi WCDMA BTS Optional Items document. The FPDA is presented in the following figure.
43 (83)
DN70150502
Figure 21.
10.2
Width
44 (83)
10.3
FPDA front panel connectors, connector types and purposes Connector type
M10 bolts M10 bolts 2 x RJ-45*
Purpose
DC input DC output Alarms**
*for chaining **Alarm 1 (AL01): DC input failure (alarm is sent when DC input voltage is missing or it is out of range). **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, cooling fan failure, output power is low or over temperature shut down is ON). The FPDA front panel is presented in the following figure.
45 (83)
Alarm cabling
DC Output cabling
GND
DN70141402
Figure 22.
10.4
46 (83)
11
LED
DN70265249
Figure 23.
47 (83)
Figure 24.
FPAB connectors
See the following figure for installing the FPAB in the RF Module.
48 (83)
DN70286831
Figure 25.
FPAB dimensions The dimensions of the FPAB are presented in the following table.
49 (83)
50 (83)
12
12.1
Integrated long term battery backup solution (MIBBU) Flexi Power Rectifier (FPRx) EAC connection box (FSEB) Overvoltage protection box (FSEC)
51 (83)
DN70253985
Figure 26.
FCIA cabinet
12.2
52 (83)
Flexi System External OVP (FSEC) Flexi System External OVP (FSEC) is installed on the cabinet roof. Multi Integrated Battery Backup Solution (MIBBU) The optional Multi Integrated Battery Backup solution (MIBBU) with a separate battery can be installed in Nokia Flexi BTS Indoor Cabinet. The Multi Integrated Battery Backup Solution consists of
.
one power distribution unit (WPU) with one control unit (CU), and one to four rectifier power units (WPM).
The power distribution unit mainly distributes the input AC mains to the rectifier units. The control unit controls the rectifier power units and monitors the alarms in the event of low supply voltage, or if the MIBBU enters the battery backup mode in the event of an AC mains failure. The alarm generated by the control unit is forwarded to the BTS O&M software. Flexi Power Rectifier (FPRx) The Flexi Rectifier Module (FPRA) is a modular 6kW output power AC rectifier package made up of three individual 2kW AC/DC power modules operating in a parallel mode configuration. The FPRA outputs a positive earthed 54VDC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It supports 2G and 3G Flexi BTS configurations (indoor and outdoor cabinets, and stack, pole and wall configurations). Flexi Battery Mounting Kit for FCIA (FMBB) Flexi Battery Mounting Kit (FMBB) is needed when using batteries or the MIBBU solution in FCIA. The mounting kit is installed at the bottom of the cabinet.
12.3
53 (83)
Width
Depth
62 kg (136 lbs.) 36 U
54 (83)
13
13.1
it provides the base station and cables protection against external damage and foreign objects it supports earthquake protection it houses the Flexi cabinet site support module (FCSA) that provides long-term battery back-up and a 4U-high IP55-protected space for Line Terminal Equipment (LTE) together with Flexi cabinet air filter (FCFA), it protects the BTS in extremely dirty conditions
The FCOA provides earthquake protection for an installation of more than nine modules.
55 (83)
DN70138414
Figure 27.
FCOA cabinet
13.2
56 (83)
The air filter is installed in the back of the cabinet, replacing the original back wall. It consists of a filter element, 8 x diagonal fans, a pressure sensor, a control logic, and back wall mechanics. The wind plate is installed in the cabinet door. The control of the FCFA fans is based on a pressure sensor. The pressure sensor measures pressure inside the cabinet and this information is then used for controlling the fan speed. The air filter is presented in the following figure.
DN70150526
Figure 28.
Air filter
57 (83)
Flexi Cabinet Site Support Module (FCSA) The optional site support module (FCSA) can be used with the outdoor cabinet to provide long-term battery back-up time for the Flexi WCDMA BTS and a space for installing Line Terminal Equipment (LTE) units. The FCSA provides IP55 protected installation space for the PDU unit, IBBU AC interface box, rectifier units, LTE equipment, control card, heat exchanger, and fans. There is a separate option for battery installation in the site support module. Batteries are fixed and cabled using Flexi Mounting Kit for Batteries (FMBA). The kit contains battery cables, a cable from IBBU to the battery cables for safe installation, rubber spacers, and front fixing parts to the batteries. The site support is presented in the following figure.
58 (83)
Heat Exchanger
MIBBU
Control card
Figure 29.
Site support
Flexi Power Rectifier (FPRx) The Flexi Rectifier Module (FPRA) is a modular 6kW output power AC rectifier package made up of three individual 2kW AC/DC power modules operating in a parallel mode configuration. The FPRA outputs a positive earthed 54VDC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It supports 2G and 3G Flexi BTS configurations (indoor and outdoor cabinets, and stack, pole and wall configurations).
59 (83)
Flexi Cabinet Fire Detector (FCDA) The fire detector is installed on the cabinet roof, and the cables are routed to the Flexi System External Alarm (FSEB). The following figure presents the fire detector.
DN70150541
Figure 30.
Fire detector
Flexi System External OVP (FSEC) Flexi System External OVP (FSEC) is an IP-protected box for overvoltage protection and power terminals. The FSEC is installed on the cabinet roof. For more information on the FSEC, see Flexi System External OVP (FSEC) description.
13.3
60 (83)
Dimensions and weight of the Flexi Cabinet for Outdoor (FCOA) Value
1550 mm (61 in.)
Width
Depth
Weight (empty cabinet) Weight (with air filter) Weight (with air filter and wind plate) Total weight (Fully equipped with batteries) Free space for modules
Max. 80 kg (177 lbs) 104 kg (230 lbs) 110 kg (243 lbs) 365 kg (807 lbs) 40 U (30 U horizontally + 5 U + 5 U vertically
61 (83)
62 (83)
14
14.1
63 (83)
DN70324735
Figure 31.
64 (83)
DN70324723
Figure 32.
The FMSA provides installation space for up to any two Flexi 3U modules and the plinth (6U in total). It is installed on a pole or wall. The FMSB provides space for up to any six Flexi 3U modules and the plinth (18U in total). It is installed on the floor.
65 (83)
Flexi 3U Mounting Covers front/back (FMCA) as well as RF Module and System Module cable entries are not used in mounting shield installations. The cabinet door is right-handed (the handedness cannot be changed). For installation instructions, see sections Installing Flexi Mounting Shield 6U (FMSA) and Installing Flexi Mounting Shield 18U (FMSB) in the Installing Flexi WCDMA BTS Modules in Cabinets document.
14.2
66 (83)
15
15.1
UltraSite EDGE BTS (CRMA) UltraSite Indoor Cabinet (IDCA) v. 101 UltraSite Outdoor Cabinet (ODCA) v. 101
67 (83)
2G
System Module
1 U free space
RF Module
DN7082146
Figure 33.
Tip
The example RF Modules shown in the figure are Dual RF Modules.
Before the mounting kit can be installed, the following parts are removed from the lower half of the GSM/EDGE UltraSite cabinet:
.
68 (83)
The mounting kit consists of one dual rack in which one System Module and one RF Module are installed, one single rack for the second RF Module installation, and cables. There is a remaining space of 1 U in the single rack when the RF Module is installed. For installation instructions, see section Overview of installing modules in cabinet with Flexi Mounting Kit Vertical for 2G in the Installing Flexi WCDMA BTS Modules in Cabinets document.
15.2
69 (83)
DN7082037
Figure 34.
70 (83)
15.3
Dual rack
694 mm (27.3 in.)
Single rack
585 mm (23 in.) 196 mm (7.7 in.) 400 mm (15.8 in.) 4.6 kg (10.2 lbs) 0.7dB
Width
Depth
Weight
0.7dB
71 (83)
72 (83)
16
16.1
UltraSite Indoor Cabinet (IDCA) v. 202 or newer UltraSite Outdoor Cabinet (ODCA) v. 202 or newer UltraSite EDGE Outdoor Cabinet (ODCF)
73 (83)
DN70231874
Figure 35.
The mounting kit consists of a rack in which, for example, one WCDMA System Module, up to three WCDMA RF Modules and one FPMA or System Extension Module or FPDA are installed, and cables. The space requirement for 5 x 3U modules is 15U. For installation instructions, see section Installing modules in cabinet with Flexi Mounting Kit Horizontal for 2G in the Installing Flexi WCDMA BTS Modules in Cabinets document.
16.2
74 (83)
Property
Height Width Depth Weight of the side wall Weight (cables excluded) The loss of RF cables
FMUB
732 mm (28.8 in.) 525 mm (20.7 in.) 393 mm (15.5 in.) 1.73kg (3.8 lbs) Max. 20 kg (44 lbs)
0.7dB
75 (83)
76 (83)
17
17.1
Figure 36.
The I-HSPA Adapter can be fitted to a Flexi BTS 2U module casing. When used with the Flexi BTS module casing, the I-HSPA Adapter can be installed with the Flexi WCDMA BTS in stand-alone configurations, such as free-standing, wall mounted or pole mounted.
77 (83)
Rear Cover
Casing
Front Cover
DN70287651
Figure 37.
The I-HSPA Adapter uses forced air cooling based on fresh air intake from back to front. This allows it be installed either horizontally or vertically. The contents of the I-HSPA Adapter delivery also include an air-blocking plate, to be used if the I-HSPA Adapter is with the Flexi BTS 2U module casing. The I-HSPA Adapter features a lightweight aluminium alloy casing with stainless steel alloy used for the fan carrier.
Figure 38.
78 (83)
17.2
Table 27.
Width without the fastening ears Height Depth from front plate Weight, including core mechanics, PWB and PMS
Table 28.
Width Height Depth Weight
17.3
Table 29.
Purpose
External transport
Interface type
Connector Type
Optical for Ethernet SFP, SFP cage (reserved for future use) 10/100/1000 BaseT Ethernet RJ45 shielded
EIF2 (TRS/LMT)
79 (83)
Table 29.
Purpose
External transport BTS interface 48VDC Power Input
Interface type
10/100/1000 BaseT Ethernet 10/100/1000 BaseT Ethernet
Connector Type
RJ45 shielded RJ45 shielded Multi-Beam XL RA 2 pin
DC IN
EIF1
DN70282859
EIF2
EIF3
EIF4
Figure 39.
80 (83)
18
81 (83)
Roof Mounting plate 2) Citytalk cabinet and roof 2) M8 screws and washers (4 pcs) 1) Back wall 1) Standoff proximity bracket 1)
taps, clips, pins, retaining rings, and M6 screws (4 sets) 2) Air guide plate 1)
Upper rod lock support (2 pcs) 1) screws and washers (4 pcs) 2) Door 1) Door proximity bracket 1) Connection pins (4 pcs) 1) Standoff casing plate 1) Hinges (2 pcs) and screws (8 pcs) 2) 1) Part of Talk Conversion Kit 2) Existing items of Citytalk cabinet DN70318511
Figure 40.
Parts needed for installing Flexi WCDMA BTS modules in Citytalk cabinet with Talk Conversion Kit EMIA
82 (83)
Screws and washers (4pcs) 2) Upper rod lock support (2pcs) 1) Top IP Cover 1) Air guide plate 1) Citytalk cabinet and roof 2) Roof mounting plate 2)
Back wall
Rack side plate Left and right assembly 1) Taps, clips, pins retaining rings and M6 screws (4 sets) 2)
Rack plinth 1) Lock cylinder 2) Lock cover 1) Standoff proximity bracket 1) Door proximity bracket 1) Door 1) Hinges (2 pcs) and screws (8pcs) 2)
Figure 41.
Parts needed for installing Flexi WCDMA BTS modules in Citytalk cabinet with Talk Conversion Kit EMIB
83 (83)