Escolar Documentos
Profissional Documentos
Cultura Documentos
Prepared by Office of Radiation, Chemical and Biological Safety and Department of Police and Public Safety
May 2003
Table Of Contents
Summary ........................................................................................................................1 Scope..............................................................................................................................1 Reference Regulations ...................................................................................................1 Definitions......................................................................................................................2 Responsibility ................................................................................................................2 Procedures......................................................................................................................3 Conduct a Hazard Assessment of the Workplace ....................................................3 Certify a Hazard Assessment was Performed..........................................................4 PPE Selection Guidelines ........................................................................................5 General Considerations......................................................................................5 Eye and Face Protection.....................................................................................5 Eye and Face Protection in Laboratories ...........................................................6 Head Protection..................................................................................................6 Foot Protection...................................................................................................8 Hand Protection .................................................................................................9 Body Protection, Other than Gloves ..................................................................9 Consultation With Affected Employees ................................................................10 Training Guidelines ...............................................................................................10 Training Certification.............................................................................................11 Reassessment And Retraining................................................................................11 Technical Support ........................................................................................................12 Appendices Appendix A: Hazard Assessment Information and PPE Selection Guides .................13 Table 1. Eye and Face Protection Selection.................................................................14 Table 2. Filter Lenses For Protection Against Radiant Energy ...................................16 Table 3. Footwear Selection Guidelines ......................................................................17 Figure 1. Footwear Labeling........................................................................................19 Table 4. Selection of Footwear Materials for Chemical Resistance............................20 Table 5. Selection of Hand Protection .........................................................................21 Table 6 Selection of Protective Clothing Materials.....................................................22 Table 7 Selection of High Visibility Clothing .............................................................23 PPE Program Compliance Checklist ...........................................................................24 PPE Survey and Analysis Checklist ............................................................................25 Personal Protective Equipment Hazard Assessment Certification Form.....................27 Appendix B: PPE Training Guide................................................................................28 Table 8. Eyewear Selection Chart................................................................................30 Table 9. Proper Care, Maintenance, Useful Life and Disposal of Protective Footwear.....................................................................34 Certification of Personal Protective Equipment Training Form ..................................36
DEFINITIONS ANSI American National Standard Institute, a nonprofit, voluntary membership organization that coordinates the U.S. Voluntary Consensus Standards System. Their standards have been adopted throughout government and industry for various types of personal protective equipment. Hazard Assessment The investigation of the work environment for potential dangers that could result in an injury or illness. Material Safety Data Sheet (MSDS) A document describing the hazards and safe handling practices for a specific product. Personal Protective Equipment (PPE) Equipment worn by workers to protect against hazards in the environment. Examples include safety glasses, face shields, respirators, gloves, hard hats, steel-toed shoes, and hearing protection. RESPONSIBILITY Deans, Directors, and Department Heads Designate and authorize individuals who will be responsible for the preparation and implementation of the Personal Protective Equipment Guidelines. Provide administrative and financial support for these Guidelines within individual departments. Ensure the Personal Protective Equipment Guidelines are implemented and maintained within the department.
DPPS/ORCBS Provide oversight and administration of the program. Provide technical information and assist departments in implementing an effective PPE Program in their workplace. Provide training for PPE instruction, as needed. Review and revise the PPE Program, as needed for compliance with applicable regulations.
ORCBS will be responsible for implementation of this Program within campus laboratories. DPPS will be responsible for implementation of this Program at Grounds, Housing, Physical Plant and all Farms and Research Stations. DPPS will also be responsible for shops and non-laboratory areas, such as greenhouses, within academic departments. DPPS: Call 355-2222 ORCBS: Call 355-0153
Supervisors Implement all aspects of these Guidelines, including documentation of the hazard assessments and site specific training. Be familiar with the applicable government regulations, safety standards, and prudent safety practices to protect themselves and their fellow employees. Conduct hazard assessments (see Appendix A). Complete the Hazard Assessment Certification form. Acquire the correct PPE. Ensure that employees are trained; o General on-line training o Site-specific training. Document site-specific training and maintain records. Retrain employees if; o Changes in the workplace render previous training obsolete o Changes in the types of personal protective equipment to be used render previous training obsolete o Inadequacies in an affected employees knowledge or use of assigned personal protective equipment indicate that the employee has not retained the requisite understanding or skill. Document retraining of employees.
Employees Comply with these Guidelines and any further safety recommendations provided by supervisors and/or DPPS/ORCBS regarding PPE. Conduct assigned tasks in a safe manner and wear all assigned PPE. Report any unsafe or unhealthy work conditions and job related injuries or illnesses to the supervisor immediately.
PROCEDURES General - The following steps are necessary for compliance with the PPE Guidelines: 1. Conduct a Hazard Assessment of the Workplace A Hazard Assessment is not a new process; it is simply a formalization of what is done whenever personal protective equipment is selected based on the hazards of the job. When conducting a hazard assessment, a task is investigated and the hazards and the potential hazards associated with the task are determined. This allows selection of personal protective equipment that will protect the employee from the identified hazards. A hazard assessment may be conducted on a single employee, performing a single task, or a group of employees if all the employees perform an identical task. For example, if all employees in a group are exposed to ultraviolet radiation during one type of welding, the 3
hazard assessment could include all of the welders conducting that task. Likewise, painters using similar types of materials or laboratory workers using similar types of chemicals could be grouped under the same assessment. The individual conducting the hazard assessment must have an intimate knowledge of each task. In some cases this may require directly observing an employee. In other instances the assessor may know all the hazards associated with a job without additional review. During the hazard assessment of each task, inspect the layout of the workplace and look for the following hazard sources: a. High temperatures that could result in burns, eye injury, ignition of equipment, heat stress, etc. b. Cold temperatures that could result in frostbite, lack of coordination, cold stress, etc. c. Chemical exposure, including airborne or skin contact that would have the potential for splash on the skin or eyes, or the potential to breathe vapors or mists. d. Harmful dust or particulates e. Light radiation, e.g., welding, cutting, brazing, furnaces, heat treating, high intensity lights, etc. f. Sources of falling objects, potential for dropping objects, rolling objects that could crush or pinch the feet. g. Sharp objects that may pierce the feet or cut the hands. h. Electrical hazards. i. Observe the layout of the workplace and the location of co-workers for the potential for collision with other personnel or objects. k. Any other identified potential hazard. Where these hazards exist and could cause injury to employees, personal protective equipment must be selected to eliminate substantially the injury potential. A PPE Hazard Assessment Certification form and accompanying Hazard Assessment Checklist are attached as Appendix A. To assist each department and supervisor, sample PPE Hazard Assessment Certification forms have been done for typical tasks for various job classifications. These can be viewed on the ORCBS website. Supervisor may use these Certifications as they apply to their employees. Be sure to evaluate the completed Hazard Assessment Certifications and make any necessary modifications so that they specifically address the tasks your workers perform. There may be other tasks that your workers perform that also need to be assessed and added to the Certification form. If you need assistance, please contact ORCBS or DPPS. 2. Certify a Hazard Assessment was performed By signing the PPE Hazard Assessment Certification forms you will be certifying that this process has been completed as required by the regulation. The forms must be kept with the departmental Hazard Communication Plan. In laboratories, the forms must be 4
kept with the Chemical Hygiene Plan. ORCBS/DPPS inspectors will ask to review these forms during routine safety inspections. 3. PPE Selection Guidelines a. General Considerations For each hazard identified, select personal protective equipment that will protect the employee by creating a barrier against workplace hazards. Consider the likelihood of an accident and the seriousness of a potential accident. Personal protective equipment must be selected to protect against any hazard that is present or likely to be present. It is important for department personnel to become familiar with the potential hazards, the type of protective equipment that is available, and the level of protection that is provided by that equipment, i.e., splash protection, impact protection, etc. The personal protective equipment selected must fit the employee it is intended to protect. Make certain that employees have the correct size of protective equipment. Whenever possible, select adjustable personal protective equipment. Employee input in the selection process is critical. Personal protective equipment that fits properly and is comfortable will more likely be worn by employees. Damaged or defective protective equipment must be taken out of service immediately to be repaired or replaced and employees must be provided with the proper equipment in the interim. For the proper selection of PPE, please use the following resources: Information presented in these Guidelines; Appendix A guides: Eye and Face Protection Chart, Filter Lenses for Protection against Radiant Energy Chart; Footwear Selection Guidelines, Selection of Footwear for Chemical Resistance, Selection of Hand Protection, Selection of Protective Clothing Materials, Selection of High Visibility Clothing Technical assistance from ORCBS/DPPS and the manufacturers of PPE; MSDSs for chemicals; and University Stores Catalog, product descriptions.
b. Eye and Face Protection Eye and face protection must be used where a hazard exists due to any of the following: Flying objects or particles Molten metal Liquid chemicals Harmful contacts Exposures Acids or caustic chemicals Chemical gases or vapors Glare Air contaminants 5
Select eye and face protection based on Tables 1 and 2 of Appendix A. If the appropriate protection is not listed in the tables, such as laser eyewear, contact ORCBS or DPPS for further assistance. All protective eye and face protection must comply with ANSI Z 87.1-1989. Some departments provide prescription safety glasses while others opt for the over-the-glass safety glasses. c. Eye and Face Protection in Laboratories Appropriate eye and face protective equipment must be worn at all times in those laboratories where eye and face hazards exist. Safety glasses are required when an impact hazard exists or when working with low hazard chemicals, or when a low probability of splash exists. For example: pipeting, handling a closed bottle of an injurious chemical, mixing solutions and opening centrifuge tubes. Chemical splash goggles are required when working with smaller amounts of corrosive or injurious chemicals and a reasonable probability of splash exists. For example: pouring acid out of a 1 pint bottle, pouring methylene chloride from a 1 liter bottle or working with liquids under pressure. Face shield and chemical splash goggles are required when: working with larger quantities of corrosive chemicals and / or a high probability of eye and face injury exists. For example: working with an acid bath, pouring 4 liters of acid into a container or handling highly reactive chemicals that may spatter. d. Head Protection Head protection must be used when a hazard exists due to any of the following: Impact and penetration of falling objects Impact when working in low clearance areas Impact from hanging objects such as hooks and chains High voltage electric shock and burns Flying objects Electric shock Hair entanglement Chemicals Temperature extremes.
For example, operations requiring head protection may include: tree trimming, construction and demolition work, electric and communication line maintenance. 6
Protective Helmets (Hard Hats) Protective helmets are required where falling object hazards are present. Some examples include: working below other workers who are using tools and materials which could fall; working around or under conveyor belts which are carrying parts or materials; working below machinery or process which might cause material or objects to fall; and working on exposed energized conductors. Some examples of occupations for which head protection should be considered are: carpenters, electricians, linemen, mechanics and repairers, plumbers and pipe fitters, assemblers, packers, wrappers, sawyers, welders, laborers, freight handlers, timber cutting and logging, stock handlers, and warehouse laborers. By the MIOSHA Standards, all hard hats must be certified to meet ANSI Z89.1-1986. ANSI updated the standard in 1997 changing the types of helmets to provide for crown and side impact protection. The class designation letters have also been changed. Many suppliers are now only listing their products to the 1997 standard. All hard hats meeting the 1997 standard will also meet the 1986 standard. Be certain that hard hats provided are not bump caps. Bump caps look like hard hats but they do not meet the requirements of ANSI Z89.1-1986 and cannot be used to protect employees from the above listed hazards. To check this, inspect each hard hat to confirm that it contains the designation "ANSI Z89.1-1986 or ANSI Z89.11997. Description of Protective Helmets 1986 Standard Type 1 Type 2 Class A Class B Class C Helmets with a full brim Brimless helmets with a peak extending forward from the crown. General service, limited voltage. Intended for protection against impact hazard. Used in mining, construction, and manufacturing. Provides electrical protection from low voltage conductors (tested to 2,200 volts) Utility service, high voltage. Used by electrical workers and workers who also need protection from falling objects. Provides electrical protection from high-voltage conductors (tested to 20,000 volts) Special service, no voltage protection. Designed for lightweight comfort and impact protection. Used in certain construction, manufacturing, refineries, and where there is a possibility of bumping the head against a fixed object. Must not be used except where it has been determined that the use of other types of protective helmets is impractical, such as where chemical reaction will cause the deterioration of other types of head protection.
Description of Protective Helmets 1997 Standard Type 1 Type 2 Class G Class E Class C Helmets providing crown impact protection Helmets providing lateral impact protection General service, limited voltage. Intended for protection against impact hazard. Used in mining, construction, and manufacturing. Provides electrical protection from low voltage conductors (tested to 2,200 volts) Utility service, high voltage. Used by electrical workers and workers who also need protection from falling objects. Provides electrical protection from high-voltage conductors (tested to 20,000 volts) Conductive no electrical protection. Designed for lightweight comfort and impact protection. Must not be used except where it has been determined that the use of other types of protective helmets is impractical, such as where chemical reaction will cause the deterioration of other types of head protection.
Hair enclosures Long hair (longer than four inches) can be drawn into machine parts such as chains, belts, rotating devices, suction devices, and blowers. Hair may even be drawn into machines guarded with mesh. It may also present an ignition risk in areas near open flames or welding. Employees with long hair must cover and protect their hair with a hat, cap, net, or bandana. These items must fit so as to not present a hazard either with machinery, ignition sources, or interference with other PPE. e. Foot Protection Select protective footwear when employees work in areas where there is a danger of foot injuries due to falling and rolling objects, objects piercing the sole, and where employees' feet are exposed to electrical hazards. Select protective footwear based on Tables 3 and 4 of Appendix A. Protective footwear must comply with ANSI Z411991. Examples of situations that may require the use of protective footwear include: Handling heavy objects and/or tools that could be dropped; Work activities involving manual material handling carts, heavy pipes, or bulk rolls, all of which could potentially roll over an employee's feet; Work involving sharp objects such as nails, tacks, large staples, scrap metal, etc., which could penetrate the sole of the shoe; Work involving explosive materials such as black powder, volatile substances, cotton dust, grain dust that could be ignited by the discharge of static electricity; Work with electrical hazards; Work with electronic components.
Some occupations for which foot protection should be considered are: shipping and receiving clerks, stock clerks, carpenters, electricians, machinists, mechanics and 8
repairers, plumbers and pipe fitters, structural metal workers, assemblers, drywall installers and lathers, packers, wrappers, craters, welders, laborers, freight handlers, gardeners and grounds-keepers, timber cutting and logging, stock handlers, warehouse laborers, and farm workers. f. Hand Protection Select and use the appropriate hand protection when employees' hands may be potentially exposed to the following hazard sources: skin absorption of harmful substances severe cuts or lacerations severe abrasions punctures chemical burns irritating materials thermal burns harmful temperature extremes It is important to select appropriate gloves for a particular application and to determine how long the glove can be worn, and whether it can be reused. Cloth gloves must not be worn when operating rotating equipment such as a drill or powered threading machine. Gloves used to protect against chemical hazards should be selected based on tested performance against specific chemicals. Glove manufacturers have developed recommendations for the proper selection and use of chemically-protective gloves. For online manufacturer recommendations go to http://www.orcbs.msu.edu/chemical/glove_guide/glove_guide_master.htm or contact the manufacturer or ORCBS/DPPS for assistance. Refer to Appendix A, Table 5 for selection of hand protection other than chemically protective gloves. g. Body Protection, Other than Gloves Body protection should be worn when there is a possibility of bodily injury from hazards while performing their jobs. Workplace hazards include the following: Intense heat Splashes of hot metals and other hot liquids Impacts from tools, machinery and materials Cuts Hazardous chemicals Contact with potentially infectious materials, like blood (refer to the Biosafety Manual for PPE guidelines) Radiant energy (ultraviolet, visible, infrared) 9
Protective clothing needs to be provided only for the specific parts of the body that are exposed to the hazard. Depending on the hazards of the workplace one or more of the following may need to be provided: Vests Jackets Aprons Coveralls Sleeve protectors Surgical gowns Full body suits The process for selecting chemically resistant clothes is similar to that for gloves. Please check the manufacturers recommendations for the proper selection of chemical protective clothing or contact ORCBS. For protective clothing selection, other than chemical protection, refer to Appendix A, Table 6. MIOSHA requires the use of a fluorescent orange warning garment while flagging or directing vehicular traffic. At night the garment is required to be reflectorized. A voluntary standard, ANSI/ISEA 107-1999, has been developed to provide guidance in selecting warning garments. This standard is not required by MIOSHA. Refer to Appendix A, Table 7 for selection guidance. 4. Consultation With Affected Employees Include employees in the PPE selection process to the extent possible and provide them access to the PPE Hazard Assessment Certification form. 5. Training Requirements Training will be conducted in two phases. Online general PPE training provided through ORCBS will be required for all employees who wear PPE. Site specific PPE training will be conducted by department supervisors and documented with the PPE Training Form. On line training will include: When and why personal protective equipment is necessary; What type of personal protective equipment is necessary; How properly to don, doff, adjust and wear personal protective equipment; The limitations of the personal protective equipment; The proper care, maintenance, useful life and disposal of the personal protective equipment. 10
Site specific training will include: What type of personal protective equipment is necessary for each job; How properly to don, doff, adjust and wear personal protective equipment; How to obtain PPE Departmental cleaning, maintenance and replacement procedures.
Laboratory personnel must be instructed to remove gloves and lab coats prior to entering common areas (hallways, elevators, eating areas, rest rooms, offices, etc.). Each employee shall demonstrate an understanding of the training and the ability to use personal protective equipment properly before being allowed to perform work requiring the use of PPE. Appendix B is a PPE Training Guide which can be discussed with or distributed to employees. 6. Training Certification Certify in writing any training that has been completed. Maintain the certification with your departmental training records. Laboratories must keep the certification with the Chemical Hygiene Plan. The certification must verify that each affected employee has received and understood the required training. The record must be identified as a certification. An example Training Certification form is provided in Appendix B. 7. Reassessment and Retraining Reassessment of the workplace should be conducted when new equipment or processes are introduced that could create new or additional hazards. If necessary, new training must be completed. Accident records should be reviewed and the suitability of previously selected PPE be reevaluated, if warranted. When the supervisor has reason to believe that any affected employee who has been trained does not have the understanding or skills required to use the personal protective equipment properly, the supervisor shall retrain such employees and document the retraining. Retraining is also required when there have been changes in the workplace or personal protective equipment that render previous training obsolete, or when there are inadequacies in the affected employee's knowledge or use of the assigned personal protective equipment. TECHNICAL SUPPORT
11
All referenced guidelines, regulations, and other documents are available through ORCBS (5-0153) or DPPS (5-2221). ATTACHMENTS Appendix A - Hazard Assessment Information and PPE Selection Guides Appendix B - PPE Training Guide
12
13
SOURCE OF HAZARD
IMPACT - Chipping, grinding, machining, masonry work, woodworking, sawing, drilling, chiseling, powered fastening, riveting, and sanding HEAT - Furnace operations, pouring, casting, hot dipping, and welding.
ASSESSMENT OF HAZARD
Flying fragments, objects, large chips, particles, sand, dirt, etc. Hot sparks Splash from molten metals High temperature exposure
TYPE
B, C, D, E, F, G, H, I, J, K, L, N B, C, D, E, F, G, H, I, J, K, L, N N N G, H, K
CHEMICALS - Acid and chemical handling, use of cleaning products, paint use and clean-up products, pesticide and herbicide use. DUST - Woodworking, buffing, general dusty conditions. LIGHT and/or RADIATION - Welding: Electric arc. - Welding: Gas. - Cutting, Torch brazing, Torch soldering. - Glare.
Splash
Irritating mists Nuisance dust Optical radiation Optical radiation Optical radiation Poor vision
G G, H, K O, P, Q J, K, L, M, N, O, P, Q B, C, D, E, F, N A, B
14
15
Plasma arc cutting Torch soldering Torch brazing Carbon arc welding Operations Gas Welding: -Light -Medium -Heavy Oxygen Cutting: -Light -Medium -Heavy
Plate Thickness inches Under 1/8 1/8 to 1/2 Over 1/2 Under 1 1 to 6 Over 6
Thickness mm Under 3.2 3.2 to 12.7 Over 12.7 Under 25 25 to 150 Over 150
* As a rule of thumb, start with a shade that is too dark to see the weld zone. Then go to a lighter shade which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line in the visible light of the (spectrum) operation. ** These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece.
16
Hazard Types/Area
Falling objects
Comments
Metatarsals should be recommended any time potential hazards exist that may result in blunt trauma injury to the metatarsal portion of the foot resulting from falling, moving, or rolling objects or equipment (Not just limited to falling objects) Required Required Do Not Use Required* Do Not Use Conductive footwear must be kept clean and worn in conjunction with conductive (grounded) floors/mats/carpets. For specific voltage protection check with your footwear supplier.
Rolling objects Sharp Objects a) Glass/nails/rocks or other sharp objects Explosion Resulting from a) black powder b) volatile substances c) dust (cotton/grain elevators) Electrical Hazards a) Open circuits*/Dry Environment b) Dielectric/Non-Conductive Footwear *Open Circuits (600 Volts or less AC) Electronic Components
Recommended
Required
Do Not Use
Do Not Use
Required
Recommended
Static Dissipative Footwear must be kept clean and worn in conjunction with static dissipative flooring
*=Check with your protective footwear supplier for these specialty applications.
I/C = Impact/Compression Mt = Metatarsal Cd = Conductive EH = Electrical Hazard PR = Puncture Resistant SD = Static Dissipative
Required To meet the requirements of ANSI Z41 Standard a protective toe cap is required Do not use Use in this area is dangerous and may result in severe injury. Recommended The results of a Hazard Assessment may or may not require this special feature There are three levels of protection for Impact/Compression and Metatarsal Protection: Class 30, 50, and 75. Class 75 is recommended for most application.
17
Provides a test for a shoes capacity to protect the toe area of the foot against falling or rolling objects. There are three levels of protection: Class 30, 50, and 75. Class 75 is the highest level and is recommended for most applications. Section 2 Metatarsal Identification Code Mt
Provides standards for the protection of the upper foot (metatarsal bones) and toe areas. Designed to prevent or reduce injuries when the toe and metatarsal areas of the foot are exposed to drop hazards. There are three levels of protection: Class 30, 50 and 75. Class 75 is the highest level and is recommended for most applications. Section 3 Conductive Footwear Identification Code Cd
Conductive footwear is designed to discharge static electricity from your body through your shoes into grounded floors. Floors must be grounded so that a charge can be dissipated. Conductive footwear is designed and manufactured to minimize static electricity and to reduce the possibility of ignition of volatile chemicals, explosives, or explosive dusts. Warning Conductive footwear may NOT be worn near open electrical circuits or highly charged objects of any kind that require Electrical Hazard (NON-conductive) footwear. Section 4 Electrical Hazard Protective Sole and Heel Identification Code EH
The sole construction of Electrical Hazard footwear is designed to reduce the hazards due to the contact of the sole with electrically energized parts and to provide secondary electrical hazards protection on substantially insulated surfaces. The soles of electrical hazards footwear are designed to reduce the potential of electrical shock when soles are exposed to open circuits (600 volts AC or less). Warning Electrical Hazard non-conductive footwear may not be worn near explosives or in other environments that require Conductive footwear. Section 5 Sole Puncture Resistant Protective Device Identification Code PR
Footwear includes a sole puncture resistant protective device. This reduces the possibility of puncture wounds to the soles of the feet by objects that could penetrate the outsoles of the footwear. The protective plate must be an integral part of the shoe. Section 6 Static Dissipative Identification Code SD
Footwear designed to reduce the accumulation of excess static electricity by conducting body charge to ground, while maintaining a high enough level of electrical resistance. 18
Indicates the shoe as complying with ANSI Z41, the letters PT signify the protective section, 99 indicates the version of the standard C indicates compression C/75 = 2500 lb C/50 = 1750 lb C/30 = 1000 lb
Description Female protective footwear With impact and compression protection Male protective footwear With impact and compression protection With metatarsal and electrical hazard protection With puncture resistance Male protective footwear With impact and compression protection With puncture resistance
Line 1 2 1 2 3 4 1 2 3
Identification ANSI Z41 PT99 F 1/75 C/75 ANSI Z41 PT99 M I/75 C/75 Mt/75 EH PR ANSI Z41 PT99 M I/30 C/30 PR
19
Concentrated NR R** mineral acids Dilute mineral R R acids Alkalis NR R Fats/organic R* R acids Polar organic R NR solvents# Non-polar R R** organic solvents## Oils/lubricants R R** *=Some resistance, but only short term **=Leather with nitrile rubber coating only
Concentrated R mineral acids Dilute mineral R R acids Alkalis R R Fats/organic NR R acids Polar organic NR NR solvents# Non-polar R R organic solvents## Oils/lubricants NR R *=Some resistance, but only short term
# Polar organic solvents include those that dissolve in water including, ethanol, methanol, and acetone. ## Non-polar organic solvent do not dissolve in water and include hexane and benzene.
20
21
Paperlike fiber Disposable suits made of this material provide protection against dusts. Nomex A synthetic fiber which provides high heat resistance Kevlar A synthetic fiber which is highly resistant to cuts and punctures. Treated wool and cotton Protective clothing made from treated wool and cotton adapts well to changing workplace temperatures and is comfortable as well as fire resistant. Treated cotton and wool clothing protects against dust, abrasions, and rough and irritating surfaces Duck Closely woven cotton fabric protects against cuts and bruises while handling heavy, sharp, or rough materials. Leather- often used for protection against dry heat, flame, cuts, and abrasion. Rubber, rubberized fabrics, neoprene and plastics Protective clothing made from these materials protects against certain acids and other chemicals.
22
Class II
Class III
Emergency responders, accident site investigators, utility workers, survey crews, highway construction workers
23
24
25
Hazard
Penetration - sharp objects Penetration animal bites Penetration rough objects Penetration knives Chemicals _______________________ Extreme cold Extreme heat Blood Electrical shock Product contamination Other Impact-flying objects, chips, sand or dirt Nuisance dust UV light welding, cutting, torch brazing or soldering Chemical splashing liquid Chemical irritating mists Hot sparks-grinding Splashing molten metal Glare/high intensity lights Laser operations Other Exposure to noise levels >85 dBA 8-hour TWA Exposure to noise levels >105 dBA 8 hour TWA Exposure to sparks Other
Required PPE
Leather/cut resistant gloves Leather/cut resistant gloves General purpose work gloves Metal mesh, Kevlar, steel mesh, heavy leather Chemical resistant gloves Type____________ Insulated gloves Heat flame resistant gloves Nitrile gloves Insulated rubber gloves Type___________ Plastic, cotton, nylon Other______________ Safety glasses w/side shields Goggles w/face shield Unvented chemical goggles Welding goggles Welding helmet/shield w/safety glasses & side shields Chemical goggles/face shield Unvented chemical goggles Safety glasses w/side shields Safety goggles w/face shield Safety goggle w/face shield Shaded safety glasses Laser goggles or glasses Other Ear muffs or plugs Ear muffs AND plugs Leather Other
Notes
Ears
26
For comfort for nuisance Respiratory dust/mist System Welding fumes Asbestos Pesticides Paint Spray Organic Vapors Acid gases Oxygen deficient/toxic or IDLH atmosphere Impact-heavy objects Compression-rolling or pinching objects/vehicles Slippery or wet surfaces Electrical hazards Explosive atmosphere Penetration-sharp objects Penetration-chemical Splashing-chemical Exposure to extreme cold Other Object from overhead Impact to side of head Struck by falling object Struck against fixed object Electrical contact with exposed wires/conductors Special circumstances no electrical protection Hair entanglement, open flames Other Impact-flying objects Moving vehicles Penetration-sharp objects Penetration-knives Electrical-static discharge Hot metal or sparks Chemical ____________ Unprotected elevated walking/working surface Other
Disposable dust/mist mask Respirator w/P100 filter Respirator w/P100 filter Respirator w/cartridges as per pesticide label Respirator w/OV/P100 Respirator with organic cartridges Respirator w/acid gas cartridges SCBA or Type C airline respirator Steel toe safety shoes Leather boots or safety shoes w/metatarsal (top of foot) guards Slip resistant soles Electrical hazard shoes Conductive footwear Puncture resistant soles Chemical resistant boots/covers Rubber boots/closed top shoes Insulated boots or shoes Other Type 1 ANSI Z89.1-1997 Type 2 ANSI Z89.1-1997 Hard Hat Class Class A/G Class B/E Class C Cap, hairnet, bandana Other Long sleeves/apron/coat Traffic vest Cut-resistant sleeves, wristlets Metal mesh, Kevlar, steel mesh, heavy leather sleeves, wristlets, aprons Static control coats/coveralls Flame-resistant jacket/pants, aluminized jacket/pants Lab coat or apron/sleeves Body harness and lanyard Other
Feet
Head
Body
27
28
Potential Hazard
29
Upon completion of the training, the employee must be able to demonstrate his or her knowledge of these elements. Any type of training format can be used as long as a hands-on session is incorporated. PowerPoint presentations are available from ORCBS/DPPS to assist with employee PPE training. Documentation of training is required. Information is provided in this document for eye and face protection, as well as head, foot and hand protection. Each section can be used as needed and be adapted to individual workplaces after the completion of a Hazard Assessment to select the proper PPE. Whenever PPE is used, employee comfort should be considered. When PPE does not fit properly, workers will tend not to use it. Follow the manufacturers recommendations for proper PPE usage. EYE AND FACE PROTECTION Eye and face protection must be used where a hazard exists due to any of the following: Flying objects or particles Molten metal Liquid chemicals Harmful contacts Exposures Acids or caustic chemicals Chemical gases or vapors Glare
30
Eye and face protection is available for protection against a variety of hazards. The hazard must be identified prior to selecting the PPE to ensure the employee will be properly protected. Side shields are required when there is an impact hazard from flying objects or a chemical splash hazard present. Safety glasses and goggles can protect against impact hazards. Safety glasses are made of special materials to provide the necessary impact protection. All eye and face protection must meet the requirements of the ANSI (American National Standards Institute) Standard Z87.1-1989, entitled American National Standard Practice for Occupational and Educational Eye and Face Protection. Laser eyewear must meet the requirements of ANSI Z136.1, 136.2, and 136.3. To comply with the Michigan Occupational Safety and Health Administration (MIOSHA) requirements for PPE, eye protection must: Provide adequate protection against the hazards for which it is designed Be reasonably comfortable under the conditions of use Fit securely without interfering with vision or movement Be durable Be kept clean and in good repair
Protective eyewear and face wear should be adjusted to provide maximum protection to the areas being protected. Eyeglasses should be worn close to the face to minimize gaps that would allow foreign materials to enter the eye. Eye and face protection should be kept clean based on recommendations from the manufacturer. When the protection becomes scratched or damaged, it should be replaced. Pits or scratches may affect the impact resistance. Workers should inspect eye and face protection before wearing and replace any defective equipment. Goggles can be worn over spectacles and can be vented or non-vented. Goggles are available for splash and impact protection, depending on the hazard. Face shields are considered a secondary form of protection and must be used in combination with spectacles or goggles to offer the necessary impact protection to the eye. Filter lens protection should be selected by starting with a shade that is too dark to see the weld zone. Then go to a lighter shade, which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line in the visible light of the operation.
31
Liquid splash Chemical splash, glass breakage Potentially Infectious material splash
Laser work Furnace operations, pouring and casting molten metal Welding (electric arc) Welding (gas)
Reflected or direct beam impact Glare, heat, molten metals, hot sparks Infrared radiation and sparks Infrared radiation and sparks
32
Inspection and Maintenance Lenses of eye protectors must be kept clean. Continuous vision through dirty lenses can cause eyestrain - often an excuse for not wearing the eye protection. Daily inspection and cleaning of eye protectors with soap and warm water, or with a cleaning solution and tissues, is recommended. Pitted and scratched lenses can also be a source of reduced vision and compromised protection. Excessively pitted or scratched or otherwise damaged eye and face protection must be replaced. If safety glasses are to be worn with hearing protection, they must be compatible. If earmuffs are worn, the temple piece of the glasses must not break the seal of the muff. Thin temple piece glasses must be selected to avoid compromising the noise reduction capabilities of the muff. Cleaning and Disinfection Procedure for Shared Use Eyewear Safety eyewear should be regularly cleaned and disinfected. Eyewear issued for the exclusive use of one worker may be cleaned as often as necessary. Weekly or monthly cleaning is usually adequate but more frequent cleaning may be necessary. When eyewear is shared it must be cleaned and disinfected before use by a different employee. To clean and disinfect eyewear use the following procedure: a) b) Check lenses for scratches. Check head straps for tears or loss of elasticity. Discard and replace any defective parts. Wash in warm (43 C [110 F] maximum) water with a mild detergent or with a cleaner recommended by the manufacturer. A stiff bristle (not wire) brush may be used to facilitate the removal of dirt, taking care to not scratch the lenses When the cleaner used does not contain a disinfecting agent, eyewear should be immersed for two minutes in one of the following: i. Hypochlorite solution (50 ppm of chlorine) made by adding approximately one milliliter of laundry bleach to one liter of water at 43 C (110 F); or, ii. Aqueous solution of iodine (50 ppm iodine) made by adding approximately 0.8 milliliters of tincture of iodine (6-8 grams ammonium and/or potassium iodide/100 cc of 45% alcohol) to one liter of water at 43 C (110 F); or, iii. Other commercially available cleansers of equivalent disinfectant quality when used as directed, if their use is recommended or approved as a disinfectant by the EPA. d) Rinse components thoroughly in clean, warm (43 C [110 F] maximum), preferably running water. The importance of thorough rinsing cannot be 33
c)
overemphasized. Detergents or disinfectants that dry on face pieces may result in dermatitis. In addition, some disinfectants may cause deterioration of plastic and elastic parts if not completely removed. e) Eyewear should be hand-dried with a clean lint-free cloth or air-dried.
HEAD PROTECTION Head protection is available to protect the head from falling objects (impact and penetration), electrical hazards, and bump hazards. Protective headwear must comply with ANSI-Z89.1-1986 or 1997, entitled American National Standards for Personal Protection - Protective Headwear for Industrial Workers. Hard hats must be labeled with the ANSI Certification. ANSI reissued the Standard in 1997, adding two types of helmets: Type 1 - Helmets providing crown impact protection Type 2 - Helmets providing lateral impact protection. There are three classes of headwear addressed in the ANSI Standard. Classes A and B are for helmets listed to the 1986 Standard. Classes G and E are helmets listed to the 1997 Standard. Class A or G Helmet - will reduce the force of impact/penetration of falling objects and, are built to reduce the danger of contact with exposed low voltage conductors. Class B or E Helmet - will also reduce the force of impact/penetration of falling objects and are built to reduce the danger of contact with exposed high voltage conductors. Class C Helmet - offers the same type of impact/penetration protection as Class A and B helmets, but offers no protection from electrical hazards. Must not be used except where it has been determined that the use of other types of protective helmets is impractical, such as where chemical reaction will cause deterioration of other types of head protection. Where Required Protective helmets are required where falling object hazards are present. Some examples include: working below other workers who are using tools and materials which could fall; working around or under conveyor belts which are carrying parts or materials; working below machinery or process which might cause material or objects to fall; and working on exposed energized conductors. Hair enclosures are required for long hair (longer than four inches), which can be drawn into machine parts such as chains, belts rotating devices, suction devices, and blowers. Hair may even be drawn into machines guarded with mesh. It may also present an ignition risk in areas near open flames or welding. Employees with long hair must cover and protect their hair with a hat, cap, net, or bandana. These items must fit so as to not present a hazard either with machinery, ignition sources, or interference with other PPE. 34
Proper Usage of Protective Helmets The shell is the rigid part of the hat and the suspension is the inner portion that cradles the head. The suspension performs two functions. First it orients and keeps the helmet on the head. It is adjustable to maintain a snug and comfortable fit. The second and most important function of the suspension is to absorb and distribute the impact of a falling object. This is the reason for the space between the suspension and the shell. Never apply paints or solvents to the helmet; it could damage the strength and dielectric properties. Accessories are available for head protection such as, hearing protection, faceshields, sweat bands, and winter liners. Always follow the manufacturers direction for proper usage of accessories. Inspection and Maintenance Inspect the shell and the suspension before each use. Look for cracks, chips, dents, or deterioration or any other signs that would indicate the need to replace the shell immediately. Look for cracks, tears or broken straps in the suspension and replace as necessary. Never mix suspensions and shells from different manufacturers. Use warm soap and water to clean the helmet as necessary. FOOT PROTECTION Foot protection is necessary when hazards exist that could result in impact and compression, electrical, conductive, or metatarsal injuries. Foot protection must comply with the requirements of ANSI Z41-1991, American National Standard for Personal Protection - Protective Footwear. Selection and Maintenance Keep protective footwear clean and polished, they will last longer. Replace broken or frayed laces. Be attentive to the wear and tear on the entire shoe or boot. Refer to Table 9 for the proper care, maintenance and useful life of protective footwear.
35
TABLE 9. PROPER CARE, MAINTENANCE, USEFUL LIFE AND DISPOSAL OF PROTECTIVE FOOTWEAR
Section 1 Impact & Compression Proper care & maintenance of protective footwear Warning: If insert or insole is added, device may reduce the impact/compression clearance. Section 2 Metatarsal Keep external metatarsal guards properly laced in shoes. Section 3 Conductive Keep soles clean. Do not add comfort insoles or use foot powder, these will affect conductivity. Do not use socks made of silk, wool, or nylon, they will create static electricity Dispose after soles become contaminated and/or no longer conductive. Section 4 Electrical Hazard Avoid moisture. Keep free of conductive materials (e.g. screws, nails, metal shavings). Section 5 Puncture Resistance Section 6 Static Dissipative Keep sole clean. Do not add comfort insoles that will affect static dissipative properties adversely. Be sure insole maintains static dissipative test. Dispose after soles become contaminated and/or no longer test SD Leather Clean according to footwear manufacturers instructions. Do not store in or near direct heat Rubber Clean according to manufacturers specification to remove impurities. Do not store in direct sunlight or near electric motors1. Dispose after cracks or punctures appear in the rubber.
If evidence of physical damage to the toe and/or evidence of physical damage to the toe area or to the shoe exists, replace the footwear at once.
Dispose after an impact has occurred to the metatarsal guard or after exterior covering becomes torn exposing the metatarsal guard.
Dispose if sole is punctured or cut, embedded with conductive materials or after significant wear causes the sole thickness to diminish
(1) Sunlight and electric motors Ultra violet light from sunlight and/or ozone from electric motors may cause rubber to crack.
Worn protective footwear should not be altered or repaired to be sure the protective footwear properties remain 36
HAND PROTECTION Hand protection is available to protect against cut/punctures, abrasions, thermal burns, vibration, chemical exposures, and electrical shock. There is not a single glove that will protect from all hazards. Selection of gloves must be based on the hazards that are present, the job task, work conditions, and the duration of use. Gloves to be used to protect against the effects of chemical use should be selected based on each manufacturers glove selection charts. Do not assume that the protection offered by one manufacturers glove will apply to all types of similar gloves. The protection of each glove is based on the manufacturing processes and glove thickness. Use and Maintenance Gloves that are torn or damaged should not be used. There is potential for the glove to be caught in machinery or other equipment. Consideration of the following items is necessary when using gloves to protect against chemical hazards: Penetration - This when a chemical passes through a physical defect in the glove, such as a pinhole or tear. Inspect gloves prior to each use. Degradation- This occurs when the chemical has some noticeable effect on the glove. The glove may appear wrinkled, dimpled, or cracked. Dispose of gloves if any of these signs appear. Never use defective gloves. Permeation - Permeation is the movement of a chemical through the glove. The vapor as well as the liquid phase of chemical can pass through the glove material. This is more difficult to detect than the previous types of warning signs. This is why it is very important to utilize the glove selection guides that are provided by the manufacturer. Refer to the ORCBS Glove Guide for assistance in glove selection. http://www.orcbs.msu.edu/chemical/chemical.html Assure that the glove will provide adequate protection for the chemical to be encountered. If multiple chemical hazards exist, base the effectiveness of the glove on the chemical with the fastest breakthrough time. Inspect gloves prior to each use. If gloves are to be reused, follow the manufacturers instructions for proper decontamination and storage. It is important to note the expected service life of the glove as well, to plan for expected disposal times.
37
(PPE) training, which included the following: when PPE is necessary; what PPE is necessary; how to properly don, doff, adjust, and wear PPE; the limitations of the PPE; and the proper care, maintenance, useful life and disposal of the PPE. Each of the affected employees has demonstrated an understanding of the above and an ability to use the PPE properly. This training is in compliance with 29 CFR 1910.132 (f). Name Signature Equipment Type
Date of Training
38