ASTM A216 covers carbon Steel Castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for Fusion Welding. Election will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. The values stated in either inch-pound units or! units are to be regarded separately as standard.
ASTM A216 covers carbon Steel Castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for Fusion Welding. Election will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. The values stated in either inch-pound units or! units are to be regarded separately as standard.
ASTM A216 covers carbon Steel Castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for Fusion Welding. Election will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. The values stated in either inch-pound units or! units are to be regarded separately as standard.
ASTM A216 Standard Specification for Steel Castings, Carbon, Suitable for Fusion
Welding, for High-Teperature Ser!ice
This specification covers carbon steel castings for valves, flanges, fittings, or other pressure- containing parts for high-temperature service and of quality suitable for assembly with other castings or wrought-steel parts by fusion welding. Three grades, WCA, WCB, and WCC, are covered in this specification. election will depend upon design and service conditions, mechanical properties, and the high temperature characteristics. The values stated in either inch-pound units or ! units are to be regarded separately as standard. Within the te"t, the ! units are shown in brac#ets. The values stated in each system are not e"act equivalents$ therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. "eferenced #ocuents ASTM Standards$ A %&&'A %&&( )ractice for teel Castings, Welding, *ualifications of )rocedures and )ersonnel A +,-'A +,-( pecification for teel Castings, .eneral /equirements, for )ressure- Containing )arts 0 123 Test (ethod for 4iquid )enetrant 0"amination 0 +,5 .uide for (agnetic )article 0"amination Manufacturers% Standardi&ation Societ' of the (al!e and Fittings )ndustr' Standard$ ) 33 teel Castings for 6alve, 7langes, and 7ittings, and 8ther Components 96isual (ethod:3 *eneral Conditions for #eli!er' (aterial furnished to this specification shall conform to the requirements of pecification A +,-'A +,-(, including any supplementary requirements that are indicated in the purchase order. 7ailure to comply with the general requirements of pecification A +,-'A +,-( constitutes nonconformance with this specification. !n case of conflict between the requirements of this specification and pecification A +,-'A +,-(, this specification shall prevail. +rdering )nforation The inquiry and order should include or indicate the following; A description of the casting by pattern number or drawing 9dimensional tolerances shall be included on the casting drawing:, .rade of steel, 8ptions in the specification, and The supplementary requirements desired including the standards of acceptance. Heat Treatent All castings shall receive a heat treatment proper to their design and chemical composition. Castings shall be furnished in the annealed, or normali<ed, or normali<ed and tempered condition unless upplementary /equirement 13 is specified. =eat treatment shall be performed after castings have been allowed to cool below the transformation range. Teperature Control 7urnace temperatures for heat treating shall be effectively controlled by pyrometer. (isit our site to do,nload http://code-pdf.com/astm-a216
ASME VIII Div 1 Part UCL Welded Pressure Vessels Constructed of Material With Corrosion Resistant Integral Cladding, Weld Metal Overlay Cladding, or With Applied Linings