Escolar Documentos
Profissional Documentos
Cultura Documentos
APRIL 1982
PAGE 1 OF 4
1.
SCOPE
This Guide covers the minimum requirements for controlled-volume pumps, including packed-plunger and diaphragm pumps. However, diaphragm pumps using direct mechanical actuation are excluded. 2. REFERENCES
API (American Petroleum Institute) Standard: Std 675 Positive Displacement Pumps Controlled Volume, 1980
3. GENERAL 3.1 Controlled-volume positive displacement pumps shall conform to API Standard 675 except as modified in Section 4 of this Guide. 3.2 The vendor shall comply with the requirements of EGE 00-C-4, as well as the specific requirements of API Standard 675 as amended in Section 4 of this Guide. 3.3 In case of conflict between API Standard 675, this Guide, and EGE 15-D-12(a or b), the data sheet shall govern. 3.4 All equipment covered by this Guide shall meet the applicable noise levels established in EGE 00-B-5 without the use of acoustical enclosures.
The following items are amendments to API Standard 675. The section and paragraph numbers refer to those given in that standard.
SECTION 2 BASIC DESIGN
AS BUILT
DATE
BY PURCHASER
F F F F F F F F F F
OPERATING CONDITIONS Liquid PT, C: Normal Specific Gravity at PT Vapor Pressure at PT, kPa, abs Viscosity at PT, SSU Corrosion/Erosion Caused by Acceleration Head, m Electrical Area Hazard: Class Group Division Max. Capacity at PT, L/h: Min. Rated
G F F F F F
MODEL BY MANUFACTURER
Max.
Max.
Min.
Rated
F F
Actual
Min.
CONSTRUCTION FEATURES Nozzles Suction Discharge Flush Size Rating Racing Location
TYPE:
Diaphragm
Suction
Discharge
Diaphragm Diameter, mm
REMARKS:
MATERIALS Liquid End Contour Plate Hydraulic Diaphragm Process Diaphragm Plunger Lantern Ring Packing Gland REMARKS: Packing Valve Valve Seat Valve Guide Valve Body Valve Gasket Frame
G
PERFORMANCE: Number of Feeds Rated Capacity, L/h NPSH Required, m kW, Rated At Relief Setting
MANUFACTURERS DATA Plunger Speed, strokes/min Diameter, mm Length of Stroke, mm Pump Head: Maximum Pressure, kPa Hydro Test, kPa
REMARKS: NOTE: The absence of a modifier after kPa shall indicate gage or differential pressure.
F F F F
F F F F
F F F F
F G G G F G G F F F
DRIVERS MOTOR: Manufacturer Type Frame No. Constant Speed Variable Speed kW Volts Hz Enclosure rpm Phase Service Factor REMARKS: OTHER: Gas Driven Steam Driven Other
G G F F F F
WEIGHTS REMARKS:
SIGNAL: Pneumatic
F F F G F G
Remote Local
Electronic
Min.
Max.
Separate
F F F
External
REMARKS:
ADDITIONAL INFORMATION
AS BUILT
DATE
BY PURCHASER
F F F F F F F F F F
OPERATING CONDITIONS Liquid PT, F: Normal Specific Gravity at PT Vapor Pressure at PT, psia Viscosity at PT, SSU Corrosion/Erosion Caused by Acceleration Head, ft Electrical Area Hazard: Class Group Division Max. Capacity at PT, gph, cc/h: Min. Rated
G F F F F F
MODEL BY MANUFACTURER
Max.
Max.
Min.
Rated
F F
Actual
Min.
CONSTRUCTION FEATURES Nozzles Suction Discharge Flush Size Rating Racing Location
TYPE:
Diaphragm
Suction
Discharge
REMARKS:
MATERIALS Liquid End Contour Plate Hydraulic Diaphragm Process Diaphragm Plunger Lantern Ring Packing Gland REMARKS: Packing Valve Valve Seat Valve Guide Valve Body Valve Gasket Frame
G
PERFORMANCE: Number of Feeds Rated Capacity, gph, cc/h NPSH Required, psi bhp, Rated REMARKS: At Relief Setting
MANUFACTURERS DATA Plunger Speed, strokes/min Diameter, in. Length of Stroke, in. Pump Head: Maximum Pressure, psig Hydro Test, psig
F F F F
Witnessed
F F F F
F F F F
F G G G F G G F F F
DRIVERS MOTOR: Manufacturer Type Frame No. Constant Speed Variable Speed hp Volts Hz Enclosure rpm Phase Service Factor REMARKS: OTHER: Gas Driven Steam Driven Other
G G F F F F
WEIGHTS REMARKS:
SIGNAL: Pneumatic
F F F G F G
Remote Local
Electronic
Min.
Max.
Separate
F F F
External
REMARKS:
ADDITIONAL INFORMATION