Pacbrake Exhaust Brake Wiring Schematic For: INTERNATIONAL 4700 / 4900 MODELS 444E / DT466E /DT530E NAVPAK systems NOTE: pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051 if desired. 8 Pin connector 377 located behind fuse panel connector 7305 located at Allison ECU. The NavPak ECM requires exhaust brake circuit to be enabled.
Pacbrake Exhaust Brake Wiring Schematic For: INTERNATIONAL 4700 / 4900 MODELS 444E / DT466E /DT530E NAVPAK systems NOTE: pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051 if desired. 8 Pin connector 377 located behind fuse panel connector 7305 located at Allison ECU. The NavPak ECM requires exhaust brake circuit to be enabled.
Pacbrake Exhaust Brake Wiring Schematic For: INTERNATIONAL 4700 / 4900 MODELS 444E / DT466E /DT530E NAVPAK systems NOTE: pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051 if desired. 8 Pin connector 377 located behind fuse panel connector 7305 located at Allison ECU. The NavPak ECM requires exhaust brake circuit to be enabled.
INTERNATIONAL 4700/4900 MODELS 444E/DT466E/DT530E NAVPAK SYSTEMS
For vehicles: (WITH) Allison 1000/2000/2400 Transmissions (WITH or WITHOUT) ABS Braking (WITH) On-board air supply Phone: 800-663-0096 Fax: 604-882-9278 E-mail: info@pacbrake.com Internet: www.pacbrake.com Pacbrake is a registered trademark of Pacbrake Company. Other trademarks used herein are property of their respective holders. Printed in Canada L5252.201003 NOTE: Pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051 if desired. Dotted area indicates Pacbrake harness PN11804. Navistar supplied wires illustrated in circled area. Relays shown are de-energized. Connector 372 located above starter on DT 466 and DT530. On 444E it is located behind the cylinder head drivers side. Remove protective cap and connect to pacbrake harness (supplied). 8 Pin connector 377 located behind fuse panel Connector 7305 located at Allison ECU. The NavPak ECM requires exhaust brake circuit to be enabled. Updates or variations by vehicle manufacturers constituting changes will not be the responsibility of Pacbrake. Information for this schematic was derived from vehicle systems at the date of this printing. Connector 372 Connector 377 Connector 632/634 A B 24B 24A A B C D E F G H A 2 9 2 9 24AC 24 94-GC 92M B 7 1 J 3 1 1 1 6 1 7 3 2 Pacbrake On/Off switch 30 30 87A 87 87A 87 85 86 86 85 Torque Converter Relay NavPak ECM Pin 15 Pin 47 10 amp Ignition power Connector 372 Connector 377 13M PK 24 GY P i n B P i n A OFF Exhaust brake Pacbrake exhaust brake relay Red Pin E Pin F 24A GY 24B GY Allison 107 Allison 120 A l l i s o n
T C M
( G r e y )
C o n n e c t o r
7 3 0 5 J1-20 J1-07 Optional customer-furnished vehicle interface wiring connectors Connector 7305 Pacbrake solenoid *At grey connector locate wires #107 and #120. Connect as shown. Note: Do not use on vehicles equipped with Allison 4th Generation Transmissions, they are identified by one connector at the transmission ECU, consult Pacbrake factory