63488K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00E0.B07D.2CD4
Motherboard assembly number : 73-9832-06 Power supply part number : 341-0097-02 Motherboard serial number : FOC103248MJ Power supply serial number : DCA102133JA Model revision number : B0 Motherboard revision number : C0 Model number : WS-C2960-24TT System serial number : FOC1033Z1EY Top Assembly Part Number : 800-26671-02 Top Assembly Revision Number : B0 Version ID : V02 CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M Configuration register is 0xF Switch#show flash Directory of flash:/ 1 -rw- 4414921 <no date> c2960-lanbase-mz.122-25.FX.bin 64016384 bytes total (59601463 bytes free) Switch#show ram ^ % Invalid input detected at '^' marker. Switch#show memory ^ % Invalid input detected at '^' marker. Switch#config t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname SW1 SW1(config)#int vlan1 SW1(config-if)#ip address 10.1.1.11 255.255.255.0 SW1(config-if)#no shutdown %LINK-5-CHANGED: Interface Vlan1, changed state to up SW1(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up exit SW1(config)#exit SW1# %SYS-5-CONFIG_I: Configured from console by console show running-config Building configuration... Current configuration : 1017 bytes ! version 12.2 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname SW1 ! ! ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! interface FastEthernet0/3 ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! interface FastEthernet0/8 ! interface FastEthernet0/9 ! interface FastEthernet0/10 ! interface FastEthernet0/11 ! interface FastEthernet0/12 ! interface FastEthernet0/13 ! interface FastEthernet0/14 ! interface FastEthernet0/15 ! interface FastEthernet0/16 ! interface FastEthernet0/17 ! interface FastEthernet0/18 ! interface FastEthernet0/19 ! interface FastEthernet0/20 ! interface FastEthernet0/21 ! interface FastEthernet0/22 ! interface FastEthernet0/23 ! interface FastEthernet0/24 ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/2 ! interface Vlan1 ip address 10.1.1.11 255.255.255.0 ! ! line con 0 ! line vty 0 4 login line vty 5 15 login ! ! end SW1#copy ru SW1#copy running-config s SW1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] SW1#sh SW1#show ip in SW1#show ip interface brie SW1#show ip interface brief Interface IP-Address OK? Method Status Protocol
FastEthernet0/1 unassigned YES manual up up
FastEthernet0/2 unassigned YES manual down down
FastEthernet0/3 unassigned YES manual down down
FastEthernet0/4 unassigned YES manual down down
FastEthernet0/5 unassigned YES manual down down
FastEthernet0/6 unassigned YES manual down down
FastEthernet0/7 unassigned YES manual down down
FastEthernet0/8 unassigned YES manual down down
FastEthernet0/9 unassigned YES manual down down
FastEthernet0/10 unassigned YES manual down down
FastEthernet0/11 unassigned YES manual down down
FastEthernet0/12 unassigned YES manual down down
FastEthernet0/13 unassigned YES manual down down
FastEthernet0/14 unassigned YES manual down down
FastEthernet0/15 unassigned YES manual down down
FastEthernet0/16 unassigned YES manual down down
FastEthernet0/17 unassigned YES manual down down
FastEthernet0/18 unassigned YES manual down down
FastEthernet0/19 unassigned YES manual down down
FastEthernet0/20 unassigned YES manual down down
FastEthernet0/21 unassigned YES manual down down
FastEthernet0/22 unassigned YES manual down down
FastEthernet0/23 unassigned YES manual down down
FastEthernet0/24 unassigned YES manual down down
GigabitEthernet1/1 unassigned YES manual down down
GigabitEthernet1/2 unassigned YES manual down down
Vlan1 10.1.1.11 YES manual up up SW1#clock set ? hh:mm:ss Current Time SW1#clock set 11:35:00 ? <1-31> Day of the month MONTH Month of the year SW1#clock set 11:35:00 08 ? MONTH Month of the year SW1#clock set 11:35:00 25 ? MONTH Month of the year SW1#clock set 11:35:00 25 August ? <1993-2035> Year SW1#clock set 11:35:00 25 August 2014 SW1#copy run SW1#copy running-config s SW1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] SW1#show version Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEAS E SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team ROM: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc 4) System returned to ROM by power-on Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memor y. 24 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s) 63488K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00E0.B07D.2CD4 Motherboard assembly number : 73-9832-06 Power supply part number : 341-0097-02 Motherboard serial number : FOC103248MJ Power supply serial number : DCA102133JA Model revision number : B0 Motherboard revision number : C0 Model number : WS-C2960-24TT System serial number : FOC1033Z1EY Top Assembly Part Number : 800-26671-02 Top Assembly Revision Number : B0 Version ID : V02 CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M Configuration register is 0xF SW1#show clock *11:38:22.128 UTC lun ago 25 2014 SW1#show terminal | include history size ^ % Invalid input detected at '^' marker. SW1# %SYS-5-CONFIG_I: Configured from console by console show terminal Line 0, Location: , Type: Length: 24 lines, Width: 80 columns Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits Status: PSI Enabled, Ready, Active, Automore On Capabilities: none Modem state: Ready Modem hardware state: CTS* noDSR DTR RTS Special Chars: Escape Hold Stop Start Disconnect Activation ^^x none - - none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response 00:00:30 Autoselect Initial Wait not set Modem type is unknown. Session limit is not set. Time since activation: 00:03:04 Editing is enabled. History is enabled, history size is 10. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are All. Allowed output transports are pad telnet rlogin. Preferred transport is telnet. No output characters are padded No special data dispatching characters SW1>show terminal Line 0, Location: , Type: Length: 24 lines, Width: 80 columns Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits Status: PSI Enabled, Ready, Active, Automore On Capabilities: none Modem state: Ready Modem hardware state: CTS* noDSR DTR RTS Special Chars: Escape Hold Stop Start Disconnect Activation ^^x none - - none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response 00:00:30 Autoselect Initial Wait not set Modem type is unknown. Session limit is not set. Time since activation: 00:03:04 Editing is enabled. History is enabled, history size is 10. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are All. Allowed output transports are pad telnet rlogin. Preferred transport is telnet. No output characters are padded No special data dispatching characters SW1>show terminal | include history size ^ % Invalid input detected at '^' marker. SW1> SW1>enable SW1#config t Enter configuration commands, one per line. End with CNTL/Z. SW1(config)#line console 0 SW1(config-line)#history size 100 SW1(config-line)#end SW1# %SYS-5-CONFIG_I: Configured from console by console copy runn SW1#copy running-config s SW1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] SW1#show terminal Line 0, Location: , Type: Length: 24 lines, Width: 80 columns Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits Status: PSI Enabled, Ready, Active, Automore On Capabilities: none Modem state: Ready Modem hardware state: CTS* noDSR DTR RTS Special Chars: Escape Hold Stop Start Disconnect Activation ^^x none - - none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response 00:00:30 Autoselect Initial Wait not set Modem type is unknown. Session limit is not set. Time since activation: 00:03:04 Editing is enabled. History is enabled, history size is 100. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are All. Allowed output transports are pad telnet rlogin. Preferred transport is telnet. No output characters are padded No special data dispatching characters SW1#config t Enter configuration commands, one per line. End with CNTL/Z. SW1(config)#no ip domain lookup SW1(config)#line console 0 SW1(config-line)#exec-timeout 60 SW1(config-line)#exit SW1(config)#exit SW1# %SYS-5-CONFIG_I: Configured from console by console copy runn SW1#copy running-config st SW1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] SW1#show terminal line console 0 ^ % Invalid input detected at '^' marker. SW1#show terminal Line 0, Location: , Type: Length: 24 lines, Width: 80 columns Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits Status: PSI Enabled, Ready, Active, Automore On Capabilities: none Modem state: Ready Modem hardware state: CTS* noDSR DTR RTS Special Chars: Escape Hold Stop Start Disconnect Activation ^^x none - - none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response 00:00:30 Autoselect Initial Wait not set Modem type is unknown. Session limit is not set. Time since activation: 00:03:04 Editing is enabled. History is enabled, history size is 100. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are All. Allowed output transports are pad telnet rlogin. Preferred transport is telnet. No output characters are padded No special data dispatching characters SW1#show terminal | begin Timeouts ^ % Invalid input detected at '^' marker. SW1#config t Enter configuration commands, one per line. End with CNTL/Z. SW1(config)#line console 0 SW1(config-line)#logging syn SW1(config-line)#logging synchronous SW1(config-line)#end SW1# %SYS-5-CONFIG_I: Configured from console by console SW1#copy running-c SW1#copy running-config s SW1#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] SW1#