3) What is fdbm and sdbm? differentiate it? 4) What is the ranges of Fdbm & Sdbm? 5) What is handover in telecom? 6) What is handover failure? 7) How u will determine the particular cell is overshooting while performing drive test? 8) Whats are the reason for quality degradation? 9) Whats is BCCH frequency and what is TCH frequency? 10) In idle mode fdbm, sdbm and RxQual value visible or not? 11) Where you observed data in tems? 12) When you establish internet connection which even comes first? 13) What is Ec/No in 3g? 14) What is AS, NS and DN? 15) Pilot pollution? 16) How you monitor data in 3g? 17) How much active set can be there in neighbor window? 18) What is IRAT?
In the following questions, please select one alternative which you think is the best answer for the particular question.
Q1. SMS broadcast is done over which channel
1. SDCCH 2. BCCH 3. TCH 4. A & C
Q2. The parameter number of Slot Spread Trans (SLO)(BTS) is used to allocate a number of CCCH blocks for .
a) Paging Channel (PCH) b) Random Access Channel (RACH) c) Access Grant Channel (AGCH) d) Traffic Channel
Q3. Which of the following comment is true?
a) MAIO step is used to avoid intra-cell interference where as HSN is used to avoid inter-cell interference b) HSN is used to avoid intra-cell interference where as MAIO step is used to avoid inter-cell interference c) Both MAIO step and HSN are used to avoid intra-cell interference. d) Both MAIO step and HSN are used to avoid inter-cell interference
Q4. Timer T200 is related with which KPI
a) SDCCH Completion rate b) Paging success rate c) TCH assignment success rate d) All of the above
Q5. Which parameter defines how often paging messages are sent to MS?
a) No of Multi-frames between Paging (MFR) b) Max No of Retransmission (RET) c) No of Slots Spread Transmission (SLO) d) No of Blocks for Access Grant (AG)
Q6. Which parameter is used as a margin to prevent ping-pong location updates?
a) PLMN-Permitted (PLMN) b) Rx Level Access Minimum (RXP) c) Cell Reselect Hysteresys (HYS) d) Handover Margin Level (LMRG)
Q7. Which Parameter describes the minimum received field strength required by an MS to get any service from the network in that cell in Idle mode?
a) PLMN-Permitted (PLMN) b) Rx Level Access Minimum (RXP) c) Cell Reselect Hysteresis (HYS) d) Direct Access Level (DAL)
Q8. When is location updates carried out?
a) Every time an MS changes its location area under one MSC. b) Every time an MS changes between two different MSCs c) On a periodic basis set by a timer d) All of the above
Q9. Increasing Radio Link Time Out (RLT) from 16 to 24 will improve following KPI
a) SDCCH Completion rate b) TCH Completion rate c) Paging Success rate d) All of the above
Q10. If a cell is having TCH congestion, which of the following is true?
a) It is having TCH blocking b) It may have TCH blocking. c) It is having TCH Drop. d) All of the above
Q11. Which of the parameter is set to zero for cyclic hopping?
a) BTS Hopping (HOP) b) Hopping sequence number (HSN) c) MAIO Offset (MAIO) d) All of the above
Q12. What is directed retry?
a) A feature that allows a recovery system to restore a BCCH to its original TRX after fault has been eliminated. b) It is designed to control the traffic load of a frequency hopping radio network in which frequencies are reused tightly. c) It is used in call set up to assign a TCH to an MS from a cell outside the serving cell due to TCH congestion d) None of the above
Q13. Which of the following is measured as BER?
a) Received Signal Quality (RX QUAL) b) Speech Quality Index (SQI) c) Voice Quality d) All of above
Q14. Polarization is characterized by
1. Direction of Magnetic Field 2. Direction of Electric Field 3. Direction of Electromagnetic Field 4. None of Above.
Q15 Which one is correct for TMA, TMB and Repeater?
1. Amplifies U/L, Amplifies D/L, and Amplifies both. 2. Amplifies D/L, Amplifies U/L, and Amplifies both. 3. Amplifies U/L, Amplifies D/L, and Amplifies U/L. 4. Amplifies U/L, Amplifies D/L, and Amplifies D/L.
Q16 Define Beam width of Antenna?
1. Angular distance between the points on two opposite sides of the peak direction where the radiation intensity drops to the 1/2 of the peak intensity. 2. Angular distance between the points on two opposite sides of the peak direction where the radiation intensity drops to the 1/3 of the peak intensity. 3. Angular distance between the points on two opposite sides of the peak direction where the radiation intensity drops to the 1/4 of the peak intensity. 4. Angular distance between the points on two opposite sides of the peak direction where the radiation intensity drops to the 1/8 of the peak intensity.
Q17 From which technique we cancel the effect of Rayleigh Fading?
1. Tilting of Dipoles. 2. Inserting Phase Shift. 3. Inserting attenuation. 4. None of the above.
Q20 Which Antenna has the highest front to back Ratio?
1. Loop 2. Yagi 3. Dipole 4. Parabolic
Q21 Select relation between forward power and Reflected Power if load is not connected?
1. VSWR=1 2. VSWR= 3. VSWR=0 4. VSWR=1/2
Q22 What is the difference between splitter and coupler?
1. Even Distribution of Power in coupler and uneven distribution in splitter. 2. Uneven Distribution of Power in coupler and even distribution in splitter. 3. Even Distribution of Power in both. 4. Uneven Distribution of Power in both.
Q23. What are mobility management states in GPRS?
1. Idle,Standby,Ready 2. Dedicated,Standby,Ready 3. Idle,Dedicated,Standby 4. None of above
Q24. Which modulation is used for EDGE above MCS-4
1. QPSK 2. GMSK 3. 8PSK 4. PSK
Q25. What does SGSN stands for?
1. Serving Gateway Support node 2. Serving GPRS Support node 3. Serving GMSC Support node 4. None of the above
Q26 In dedicated mode, SMS comes on which channel? a) SDCCH. b) SACCH. c) FACCH. d) None of the above.
Q27 In Dedicated Mode, MS receives which system info. Messages?
1. System Info 1, 2, 3. 2. System Info 1, 2, 3,4,13. 3. System Info 5, 6. 4. None of the above.
Q28 Freq used in Uplink of Satellite communication is higher while in GSM it is lower. Why?
1. Loss freq. 2. Loss 1/freq. 3. Loss sqr(freq) 4. None of the above.
Q29 AMR is used to improve?
1. SQI 2. Downlink quality. 3. Uplink Quality 4. None of the Above.
Q30 In Idle Mode, MS receives which system info. Messages?
a) System Info 1, 2,3. b) System Info 1, 2, 3,4,13. 3. System Info 5, 6. d) None of the above
Q31 The Common Control channel multiframe consists of? 1. 51 time slots. 2. 50 timeslots 3. 4 Time slots 4. 9 Time slots
Q32 Which of the following are true?
1. Type 1 Paging: can address up to 2 mobiles using either IMSI or TMSI. 2. Type 2 Paging: can address up to 3 mobiles, one by IMSI and the other 2 by TMSI. 3. Type 3 Paging: can address up to 4 mobiles using the TMSI only. 4. All of the above.
Q33 In GSM while performing handover
1. The MS breaks connection from source cell and then tunes on the target cell. 2. The MS continues connection from the source, tunes on the target and then releases the source cell. 3. MS gets paging message from the target and replies it on its RACH and gets TCH allocated. 4. MS gets paging message from the target and replies it on its RACH and gets SDCCH allocated.
Q34 If E-RACH is used then which of the following is true?
1. GSM range will increase beyond 35Km 2. It will increase no of RACH channels and release congestion on RACH. 3. SDCCH assignment will improve. 4. All above are false.
Q35 In dedicated mode the BTS receives handover command on?
1. Terminal Equipment identifier 2. Transcoder Input Erlang 3. TRX identifier for Edge TRX 4. None of the above
Q39 As per GSM Standard in case of frequency hopping the C/I value should be at least?
1. 3 dB 2. 6 dB 3. 9 dB 4. 12 dB
Q40 In inter BSC handover the handover is controlled by?
1. GMSC 2. MSC 3. Source BSC 4. Target BSC
Q41 The maximum no of neighbors that can be defined with a cell is?
1. 8 2. 16 3. 32 4. 64
Q42 The permissible value of VSWR for feeder cable is?
1. < 1.3 2. >1.3 3. > 1 4. <2
Q43 The function of Transcoder is
1. To convert 64 kbps speech channel on A interface to 16 kbps speech channel on A-ter Interface and vice versa. 2. To convert 16 kbps speech channel on A interface to 64 kbps speech channel on A-ter Interface and vice versa. 3. To convert analogue speech signal from MSC to Digital signal for use of BSC 4. To convert analogue speech signal from BSC to Digital signal for use of MSC
Q44 TSC stands for
1. Time Synchronized Channel 2. Temporary subscriber code 3. Transcoder Signaling Controller 4. Training Sequence Code
Q45 If Cell bar is set to yes on a cell then
1. It will reject new calls as well as handover calls 2. It will reject new call assignment but will receive calls by Handover 3. It will reject Handover but allow new call to come 4. The BTS will go into locked state.
Q46 DAP stands for
1. Dual Abis pool 2. Dynamic Allocation protocol 3. Dynamic Abis Pool 4. None of the above
Q47 Who can initiate the GPRS detach
1. The MS only 2. The SGSN only 3. Both the MS and the SGSN 4. None of the above
Q48 The mapping of logical name/Host name to IP addresses in the GPRS network is done by
1. Border Gateway 2. SGSN 3. GGSN 4. DNS
Q49 Where is the mobility management context established in GPRS
1. In the MSC 2. In the SGSN 3. In the GGSN 4. All of the above
Q50 Which layer uses the functionality of Uplink State Flag (USF)?
1. RLC Layer 2. Physical Layer 3. MAC Layer 4. All of the above
Q51 How many TDMA frames are there in a PDCH multiframe?
1. 51 2. 52 3. 26 4. 8
Q52 Which coding scheme does not use Forward Error Correction (FEC)?
1. CS-1 2. CS-2 3. CS-3 4. CS-4
Q53 Which new area is defined in GPRS compared to GSM?
1. Location Area 2. Routing Area 3. Both a and b 4. None of the above
Q54 Which layer is responsible for segmentation and reassembly of LLC PDUs and backward error correction (BEC) procedures?
a) Downlink direction b) Uplink direction c) In both direction d) As a Amplifier
Q58 Number of AMR codec modes used only in FR?
1. 6 2. 4 3. 2 4. 8
Q59 During conference call which channel is used to establish another call-
1. SACCH 2. SDCCH 3. FACCH 4. TCH
Q60 What is Duplex spacing.
1. Difference between first frequency of Uplink and last frequency of Downlink. 2. Difference between first frequency of Downlink and first frequency of Uplink. 3. Difference between last frequency of Downlink and first frequency of Uplink. 4. None of the above.
Q61 What does MSRN stands for .
1. Mobile Station Registration Number 2. Mobile System Registration Number 3. Mobile Station Roaming Number 4. Mobile Station Register Number.
Q62. If my MCC=404, MNC=05, LAC=100, CI = 14011, then what will be CGI for same??
Q63. Which information is there in Handover Access Command in Layer 3 Message?
1. BCCH & BSIC of Source 2. BCCH & BSIC of Target 3. Handover Reference Value 4. All of above.
Q64 What is the use of Immediate Assignment Extended Command?
1. Allocate AGCH for 2 Mobiles 2. Allocate SDCCH for 3 Mobiles 3. Allocate SDCCH for Call and SMS simultaneously. 4. None of Above.
Q65. What is the cause value for normal call release? 1. 16 2. 3 3. 14 4. 45
Q66. Location Update Request falls under which management system? 1. RRM 2. CM 3. CRM 4. MM
Q67. Which system information message contains NCC Permitted Values? 1. SI 6 2. SI 2 3. All of Above. 4. None of Above.
Q68. When timer T3212 expires which process is initiated? 1. Cell Update 2. RAC Update 3. LAC Update 4. Handover
Q69. If AMR FR & AMR HR is enabled in network, then what will be the formula for counting GSM FR Traffic with help of EOSFLX KPI Reports ? 1. Total Traffic AMR FR Traffic 2. Total Traffic AMR FR Traffic - AMR HR Traffic 3. Total Traffic GSM HR Traffic AMR FR Traffic AMR HR Traffic 4. None of Above.
Q70. By reducing value of RET parameter it will help to improve which KPI? 1. TCH Drop 2. SDCCH Drop 3. HO Success 4. None of above.
Q71. What is the range of AMH TRHO PBGT Margin parameter? 1. -6 to +6, 255 2. -24 to +24, 255 3. -6 to +24, 255 4. +6 to +24, 255
Q72. What is the relation between HO Load Factor and HO Priority Level? 1. Load Factor > Priority Level 2. Load Factor >= Priority Level 3. Load factor < Priority Level 4. Load Factor <=Priority Level
Q73. Which are the basic features helps to distribute traffic in nearby cells? 1. DR 2. IDR 3. AMH 4. All of above
Q74. Using Multi BCF Common BCCH feature operator can expand how many numbers of TRX in one segment without using another BCCH? 1. 16 2. 24 3. 30 4. 36
Q75. While Using Path loss Criterion C2 which parameter should be made 0 so that this particular cell have higher C2 Value even though having poor C1? 1. CRO 2. TEO 3. Penalty Time 4. None of above.
Q76. Common BCCH feature is implemented in network, then which feature will help to access the secondary freq. spectrum directly? 1. DR 2. DADB 3. DADL 4. All of above
Q77. Which types of GSM Reports are generated by Nemo Analyzer? 1. GSM Performance Report 2. GSM Benchmark Report 3. All of above 4. None of above
Q78. What is the range of parameter PMRG? 1. -24to +63 2. -24 to +24 3. -63 to +63 4. 0 to +63
Q79. How many maximum uplink TBF can be there per RTSL? 1. 6 2. 7 3. 8 4. 9
Q80. What should be minimum value of CDED (%) to have 1 RTSL as dedicated GPRS Timeslot considering 2 TRX as GPRS TRX? 1. 0 2. 1 3. 8 4. 10
Q81. What does TRP Value = 3 means? 1. TCH allocation from BCCH TRX for non-amr user and from beyond BCCH TRX for amr USER 2. TCH allocation from beyond BCCH TRX for non-amr user and from BCCH TRX for amr USER 3. All of above 4. None of Above
Q82. How many basic EGPRS MCS Families are there? 1. 1 2. 2 3. 3 4. 4
Q83. Which is / are the main factors affecting the Radio Accessibility for TBF in UL/ DL? 1. Coverage 2. Capacity 3. Interference 4. All of above.
Q84. Which parameter setting can help to increase the TBF Retainability? 1. UL Power Control 2. DL Power Control 3. All of above. 4. None of above.
Q85. What should be SDCCH GOS when compared to TCH GOS? 1. SD GOS = TCH GOSDTX 2. SD GOS = 1/2(TCH GOS) 3. SD GOS = 1/4(TCH GOS) 4. SD GOS = 2(TCH GOS)
Q86. Which feature/technique is not used to reduce blocking / congestion? 1. Directed Retry 2. Traffic Reason Handover 3. Dynamic SDCCH 4. Intra Cell Handover
Q88. Following is false when using Dynamic SDCCH. 1. SDCCH Handover cannot be used. 2. Free TCH is used when SDCCH is required. 3. SDCCH carrying CBCH cannot be used. 4. Every SDCCH request can be fulfilled by Dynamic SDCCH.
Q89. In Link Budget; what has the least importance? 1. GSM Antenna Gain 2. Path Loss 3. Feeder Loss 4. MS Antenna Gain
Q90. When 2 calls are made from different TRXs of same cell having 1*1 RF hopping; what plays important role to neglect C/I? 1. MAL ID 2. HSN 3. MAIO Step 4. MAIO Offset
Q91. Frame loss can be reduced by: 1. Speech Coding 2. Channel Coding 3. Interleaving 4. Burst Formatting
Q92. What can be done to overcome combiner loss when cell is upgraded from 2 TRX to 3 TRX? 1. Remove Combiner 2. Air-Combining 3. HOP = OFF 4. TMA Implementation
Q93. What is the Basic feature amongst below: 1. SAIC 2. STIRC 3. AMR Progressive Power Control 4. Freq. Hopping
Q94. Out of following channels which one is common channel? 1. AGCH 2. SACCH 3. TCH-FR 4. FACCH
Q95. Out of following channels which one is the answer to RACH? 1. SDCCH 2. AGCH 3. FACCH 4. SACCH
Q96. In Air-interface TDMA time-slot means how many Seconds? 1. 576.9us 2. 4.615ms 3. 6.12sec 4. 480ms
Q97. Which type of antenna is used in MS? 1. Dipole 2. Omni 3. Loop 4. Cross-polar
Q98. Choose the correct Erlang Formula? 1. x Erlang= (calls per hour) * (average call duration)/3600 Sec 2. x Erlang= (no. of user)*(3600 sec)/ (calls per hour) 3. x Erlang= (no. of calls)*(no. of user)/ (average call duration) 4. x Erlang= (calls per hour)*(no. of users)/3600 sec
Q99. If GOS of an N/W is 3%, what does it mean? 1. 3 out of 100 calls may fails 2. average call duration is 3min 3. at a time 3% of total users can make a call 4. 3% blocking in the N/W is permitted
Q100. Which type of message is "Identity Request? 1. Mobility Management 2. Radio Resource Management 3. Call Control 4. Call related SS message
Q101. Paging message type 2 contains. 1. Paging message for 3 mobiles 2. Paging message for 2 mobiles 3. Paging message for 4 mobiles 4. Paging message for >4 mobiles
Q102. Out of following which one is not a part of NSS? 1. Mobility Management 2. Connection Management 3. Radio Resource Management 4. Charging
Q103. In L3 messages, out of following Info messages which one carries Dedicated Mode Information? 1. System Info 2 2. System Info 4 3. System Info 5 4. System Info 13
Q104. Which one out of following is not a part of AMR Codec Modes? 1. 4.6 2. 5.9 3. 7.4 4. 12.2
Q105. Frequency Hopping 1. Eliminates the problem of fading dips 2. Eliminates the problem of ISI 3. is part of channel coding 4. spreads the problem of fading dips to many mobile stations
Q106. ISI is caused by: 1. fading dips 2. the Viterbi equalizer 3. reflection 4. interleaving
Q107. Maximum data throughput / tsl possible incase of GPRS is: X` 1. 18.8kbps 2. 27.2kbps 3. 29.2kbps 4. 21.4kbps
Q108. Out of following which element/s in the GSM N/W can not initiate HO? 1. BSC 2. BTS 3. MSC 4. None of Above
Q109. Out of following, which type of antenna has highest directivity? 1. Dipole 2. Helical 3. Log-Periodic 4. Yaagi-Uda
Q110. When we say the output power of a Transmitter is 30dBm, how many watts does it mean? 1. 3W 2. 1W 3. 1mW 4. 30mW
Q111. Out of following which one is a passive device? 1. Repeater 2. Cross Polar Antenna 3. TMA (Tower Mount Amplifier) 4. TRX
Q112. Out of following which can not be observed during Drive-test? 1. Rx Quality 2. Location Update 3. Paging Load 4. GPRS Attach
Q113. If a cell is EDGE capable, how much Downlink Throughput can we guarantee to customer? 1. 59.2kbps 2. 473.6kbps 3. 236.8kbps 4. can't guarantee
Q114. How many blocks of AGCH are reserved in non combined mode?
1. 1-7 2. 0-2 3. 0-7 4. None of Above.
Q115. What are the contents of authentication triplets?
1. May or may not be implemented 2. Does not provide optimal gain if the hopping frequencies are less than 4 3. Both above are correct. 4. None of the above.
Q117 .Which of the following functions is not done by SDCCH CHANNEL:
1. Authentication 2. Transmission of short messages 3. Adaptive power control information from BTS to MS only 4. Assignment of traffic channel to MS. Q118 How many TS can be used at the most with HSCSD?
1. 2 2. 4 3. 6 4. 8
Q119 What should be the value of C/I when you are in hopping mode?
1. Above 9 2. Above 12 3. Less than 9 4. All of the above are correct
Q120 Which value of level and quality should be considered for analysis in a DT log
1. Full 2. Sub 3. Both 4. None of the above is correct.
Q121 What are the coding schemes observerd in UL/ DL after implementing EDGE in your Network:
1. CS1-CS4 2. MCS1-MCS6 3. MCS5-MCS9 4. MCS1-MCS9
Q122 What does DAP stand for?
1. Dynamic Abis Pool 2. Dynamic Access Pool 3. Dynamic Access Protocol 4. None of the above
Q123 How many codecs can be defined for AMR HR
1. 5 2. 2 3. 6 4. 4
Q124 How many TRXs can be accommodated max on a single E1 where DAP pool is assigned for 4 TS in a Ultra site
1. 12 2. 16 3. 18 4. 24
Q125 How much traffic will be offered by a sector having 4 TRX with GOS of 2%
Q127 On what basis would an optimizer decide whether the site serving is overshooting:
1. On the basis of TA 2. From ND report 232 3. Physically verifying whether the cell is having up tilt 4. All of the above
Q128 BBH is generally implemented where:
1. For dense network 2. For small capacity network 3. For cells where tight frequency reuse is required 4. None of the above
Q129 In case of Directed retry HO:
1. HO is performed from TCH of serving to TCH of Adjacent cell 2. HO is performed from SDCCH of serving to TCH of adjacent cell 3. HO is performed from TCH of Serving to SDCCH of adjacent cell 4. HO is performed from SDCCH of serving to SDCCH of adjacent cell
Q130 Which alarm indicates the TRX faulty operation in the system:
1. 7601 2. 7602 3. 7725 4. 7745
Q131 C/I estimation during a DT can be done in:
1. U/L 2. D/L 3. Both A&B 4. Cannot be estimated.
Q132 Which is the unique feature in TEMS for analsing speech quality:
1. Rx qual Full 2. Rx Qual Sub 3. SQI 4. Rx Qual.
Q133 Drop calls due to Handovers can be caused basically due to:
1. Neighbors with Co-BSIC 2. Neighbor with Co-BCCH 3. Neighbors with Co-BCCH and Co-BSIC 4. All of the above.
Q134 Consider a cell where the no calls are happening, the probable causes would be
1. Wrong definition of LAC,CI 2. DMAX=0 3. Only A is correct 4. Both A&B are correct.
Q135 What should be the value of Rxlev Access min set:
1. -47dbm 2. -110dm 3. -65dbm 4. -85dbm
Q136 What would be the output of a cell with parameter setting as MstxPwrmax=0db,BsTxPWrMax =30db
1. Cell will carry max.no of calls 2. Cell will carry very few calls 3. Cell will not be latched 4. Cell with a correct parameter setting.
Q137 What would be the power loss after using a combiner in a sector:
1. -2db 2. -1db 3. -3db 4. -4db
Q138 What will happen in case where GTRX=Y(Non Edge TRX),EDGE=Y:
1. TRX will be unlocked 2. System will not allow the TRX to be unlock 3. TRX will go in Block state 4. Both B&C are correct.
Q139 Which report would give you the total payload for GPRS:
1. 232 2. 208 3. 228 4. 226.
Q140 In a Flexi BTS 1 physical TRX would logically represent how many Trx:
1. 1 2. 2 3. 3 4. None of the above. Q141 Booster becomes a solution in case of :
1. Capacity 2. Coverage 3. A & B Both 4. None of the above
Q142 Recommended value of ITCF is :
1. 2 2. 0 3. 1 4. 4
Q143. Which ND report gives the data for RACH rejection on cell level? 5. 134 6. 132 7. 188 8. 111.
Q144. Which ND report would you refer in order to find the discrepancy for Handovers?
Q160 Which counter shows DL multislot assignment in percentage? 1. msl_13 2. msl_14 3. msl_15a 4. msl_16a
Q161. How many 64 Kbps DAP TSLs are required if MS is using MCS 9 (consider: dedicated data timeslot = 4, single data user attached)? 1. 2 2. 4 3. 6 4. 8
Q162. How many maximum Abis timeslots can be handle by PCU ? 1. 64 2. 128 3. 256 4. 264
Q163. What is the Maximum output power of Metrosite BTS in terms of Watt? 1. 5 2. 10 3. 20 4. 40
Q164. What is the maximum number of TRXs can created per BCSU in BSC 3i with version S12? 1. 110 2. 200 3. 100 4. 220
Q165. Which interface is required to implement combine paging (Voice + Data) 1. Gs 2. DPM ( Dual Paging Mode) 3. Gn 4. DPT ( Dual Paging Transmission)
Q166. In which ND report we can see TRHO Handovers attempt and success? 1. 153 2. 154 3. 155 4. 156
Q167. How many TRXs can be handled by 1 BB2F Card in Ultra Site BTS? 1. 2 2. 3 3. 4 4. 6
Q168. Which of the following BTS Type do not have combiner in-built in them? 1. Ultra Site 2. Metro Site 3. Flexi BTS 4. None of above
Q169. Which report will help to see EDAP Congestion? 1. 280 2. 281 3. 128 4. 082
Q170. In which ND report we can see paging deletion counts for cell level? 1. 180 2. 181 3. 182 4. 186
Q171 Out of following, which is true as per NSN Specification? 1. CDED<=CDEF 2. CDED>CDEF 3. CDED=CDEF+CMAX 4. CDEF=CDED+CMAX
Q172. What should be minimum value of CDED(%) to have 1 RTSL as dedicated GPRS Timeslot considering 2 TRX as GPRS TRX? 1. 0 2. 1 3. 8 4. 10
Q173 Which report shows Intra Cell Handover Statistics? 1. 150 2. 153 3. 154 4. 158
Q174 What is the maximum data throughput/timeslot can be achieved in case of MCS 9? 1. 64 Kbps 2. 59.2 Kbps 3. 118 Kbps 4. 230.4 Kbps
Q175 Which BTS Type does not support Rx Diversity (RDIV) parameter? 1. Flexi Edge BTS 2. Ultra BTS 3. Metro BTS 4. Talk Family BTS
Q176 In case of EDGE which of the following CS offers highest coverage? 1. MCS 1 2. MCS 9 3. MCS 5 4. CS 1
Q179 Noise separation feature can be implemented in? 1. TCSM 2. BSC 3i 3. Flexi BTS 4. TRX
Q180 Which of the following is not a feature of GSM network alone, but also feature of analog mobile communication network? 1. Digital transmission of user data in air interface 2. Possibility of full international roaming in any country 3. Better speech quality 4. Fully digitized switching exchange
Q181 which of the following is parameter affecting cell sites while planning the network 1. Antenna height 2. MS power 3. BTS Power 4. None Of Above
Q182 What is E interface? 1. MSC-MSC 2. MSC-VLR 3. MSC-HLR 4. HLR-VLR
Q183 In GSM which type of handover occurs? 1. Hard 2. Soft 3. Both of the above 4. Make before break
Q184 Choose the correct bit pattern of a flag in LAP-D format ? 1. 01111110 2. 11111111 3. 10101010. 4. 01010101.
Q185 Mobile identity is a part of?
1. Physical layer Info 2. Lap-D Info 3. BSSMAP Info 4. GSM L3 Info
Q186 Maximum PLMN Permitted can be ?
a) 7 b) 8 c) 1 d) 2
Q187 how many BSIC possible if NCC=4, no of BCCH ARFCN =8 ?
a) 32 b) 64 c) 256 d) 1024
Q188 DTX helps in
a) Reducing TCH congestion b) Reducing SDCCH congestion c) Reducing interference d) Improving paging success
Q189. BSSAP needs the services of SCCP to
a) Analyze A subscriber data b) To perform Connectionless signaling with the MSC c) Send MAP messages to HLR via the MSC d) To make a virtual connection between the MS and the MSC
Q190. Which of the following is true?
a) MAP stands for Mobile Access Part b) LAP-D protocol is used to communicate between MSC and BSC c) MAP is used for communication between MSC and HLR d) BSSAP is used for communicating between BSC and MS
Q191. If an inter MSC handover occurs during a call, the decision to make a handover is done by
a) BSC controlling the target cell b) MSC controlling the target cell c) BSC controlling the current cell d) MSC controlling the current cell
Q192. Which of the following is not an advantage of the GSM network Compared to other networks which use the same frequency band?
a) Lower Carrier to Interference Ratio for signal reception b) Use of MAP signaling c) Frequency reuse is more efficient than in other networks d) Lower bit rate for voice coding
Q193. The basic principle of speech coding in a GSM Mobile Station is
a) A-Law PCM with 8 bits per sample -Law PCM at 104Kbits/sb) c) A-Law PCM with special filtering at 13Kbits/s d) None of the above
Q194. Authentication verification is carried out in
a) HLR b) MSC c) VLR d) Authentication Centre
Q195. No calls initiating in a cell, handover traffic is present
1. wrong neighbor defined 2. CGI creation problem 3. Same BCCH Allocated in neighbor 4. None of above
Q196. Which of the following facility is not supported by Net monitor?
1. Neighbor Cell Id 2. DTX Status 3. Ciphering status 4. HSN
Q 197. In a cell configured with phase diversity, with air combining, what should be ideal distance between two antennas of same sector?
1. At least /4 separated 2. At least /10 separated 3. 0 distance 4. None of above
Q198. Which of the following is supported by remote tune combiner?
1. BB Hopping 2. RF Hopping 3. Cyclic Hopping 4. All of above
Q199. Which of the following is affecting SDCCH capacity on Abis Interface?
1. TRX Signaling Size 2. No of TCH in sector 3. EDAP Pool 4. OMU Signaling
Q200. Alarm no. 2993 indicates 1. TCH Drop on Abis Interface 2. TCH Drop on Ater Interface 3. TCH Drop on Air Interface 4. TCH Drop on A Interface
Example of Best Answer: ''I applied for this job since it matches my skills and abilities, my previous experience and positions. This job would allow me to use my proven skills to bring great value to this company. I am certain that I can make an impact and bring benefit to the company and to myself. This job is a logical step forward for me and if I was appointed then I feel you would not be disappointed.''