Escolar Documentos
Profissional Documentos
Cultura Documentos
()
=
Where Vs is the theoretical
volume displaced per revolution
(m
3
/rev), and n is the number of
revolutions of the gears per
second. Therefore:
()
100%
Procedure:
1. Run the IFD7 program and select FM-52. Then run the FM52 program.
2. Ensure the needle valve is fully open.
3. Set the pump to 80% and check that the pump starts to work. Check the sensor
displays and ensure that the flow rate increases from zero when the pump is
started.
4. Select the icon to record the pump setting and sensor readings in the results
table.
5. Slightly close the needle valve to give a small change in outlet pressure and
flow readings. Select the icon again.
6. Continue to close the needle valve in small increments, recording the
corresponding readings each time.
7. When the needle valve is fully closed, take a final set of readings then create a
new results sheet using the icon.
8. Take a second set of readings by opening the needle valve in small increments
until the valve is fully open.
9. Set the pump to 0% then switch the pump off.
Report:
1. For both sets of results taken, plot the flowrate, input power, volumetric efficiency
and overall efficiency against outlet pressure.
2. What can you conclude from these graphs?
3. Compare the shape of the volumetric efficiency graph with that for overall efficiency.
Campus Quertaro
3 Practice from Armfield Manual
PART B: CENTRIFUGAL PUMPS
Objective:
To obtain head, power and efficiency graphs for a centrifugal pump.
Introduction:
Turbines and centrifugal pumps are of a rotodynamic type. These pumps impart
momentum to a fluid, which then causes the fluid to move into the delivery chamber or
outlet. The operating characteristics of a centrifugal pump, as the ones used in this
practice, may be described or illustrated by using graphs of pump performance. The
most common graphical representation of these pumps are:
Change in total head produced by the pump (Ht)
Power input to the pump (Pm)
Pump efficiency (E)
Total head:
The change in total head produced as a result of the work done by pump can be
calculated as:
Ht = Change in static head + change in velocity head + change in elevation
Ht = Hs + Hv + He
and
)
2
2
Where:
Pin = fluid pressure at inlet in Pa
Pout = fluid pressure at outlet in Pa
Vin = fluid velocity at inlet in m/s
Vout = fluid velocity at outlet in m/s
He = vertical distance between inlet and outlet (0.075m for the FM-51)
Power input:
The mechanical power input to the pump may be calculated as:
Pm = rotational force x angular distance = 2
Where:
n = rotational speed of pump in revolutions per second
t = shaft torque in Nm
Pump efficiency:
The efficiency of the pump may be calculated as: =
100
Where:
Pm = mechanical power absorbed by pump = 2*n*t
Campus Quertaro
4 Practice from Armfield Manual
Ph = hydraulic power imparted to fluid = Ht*Q**g
Q = volume flow rate in m
3
/s
Each of these parameters is measured at
constant pump speed, and is plotted against the
volume flow rate, Q, through the pump. An
example of this type of graphical representation of
pump performance is given in the next figure
(Figure 1).
Figure 1 Graphical representation of pump
performance
Procedure:
1. Run the IFD7 program and select FM-51.
Then run the FM51 program.
2. Ensure the inlet valve and gate valve are fully open.
3. Set the 3-way valve for flow in parallel.
4. Close Pump 2 outlet valve. This will prevent flow through pump 2, thus directing
all the flow through a single pump, pump 1.
5. In the software, set the pump to 80%
6. Allow water to circulate until all air has been flushed from the system.
7. Close the gate valve to give a flow rate Q of 0. DO NOT LEAVE THE PUMP
RUNNING WITH CLOSED VALVE FOR A LONG TIME, DO DE NEXT STEP
FAST!
8. Select the icon to record the readings. Then open the gate valve to give a low
flow rate. Allow sufficient time for the sensor readings to stabilize then select the
icon to record the next set of data.
9. Open the gate valve in small increments, allowing the sensor readings to stabilize
then recording the sensor and pump data each time.
10. Set the pump to 0% then switch the pump off.
11. Repeat for pump at 100%, 90%, 70% and 60%.
Report:
1. Plot graph of Head against flowrate, with the 4 runs in the same plot.
2. Plot a graph of mechanical power against flowrate on one axis, and efficiency
against flowrate on the secondary axis, with the 4 runs in the same plot.
3. Plot a graph of head against flowrate on one axis, and mechanical power against
flowrate against flowrate on the secondary axis, with the 4 runs in the same plot.
4. For the results with the pump at 80%, examine and describe the shapes of the
graphs obtained, relating this to the flowrate.
5. For the results with the pump at 80%, determine the maximum efficiency and the
flowrate at which it occurs.
Campus Quertaro
5 Practice from Armfield Manual
PART C: PUMPS IN SERIES AND IN PARALLEL
Objective:
To investigate the result on discharge and total head of operating pumps in series and in
parallel.
Introduction:
When two pumps operate in series,
the flowrate is the same as for one
single pump but the total head is
increased. The combined pump
head-capacity curve is found by
adding the heads of the single pump
curves at the same capacity.
When two pumps operate in parallel
the total head increase remains
unchanged but the flow rate is
increased. The head-capacity curve is
found by adding the capacities of the
single pump curves at the same head.
Procedure:
1. Ensure the inlet valve and gate valve are fully open.
2. Set the 3-way valve for flow in series (the earlier experiments have all used this valve
in parallel).
3. Pump 1 should be set to 100%.
4. Open pump 2 outlet valve, close Pump 1 outlet valve and wait for any air to circulate
out the system.
5. Select the icon to record the readings. Close the gate valve to reduce a flow by
small increment. Select the icon again.
6. Continue to close the gate valve to give an incremental changes in flowrate,
recording the sensor data each time.
7. After taking the final set of data, fully open the valve gate again. DO NOT LEAVE
THE PUMP RUNNING WITH CLOSED VALVE FOR A LONG TIME!!
Campus Quertaro
6 Practice from Armfield Manual
8. Now, for running the pumps in parallel, fully open the Pump 1 outlet valve and Pump
2 outlet valve. Opening both valves fully ensures that the outlet pressure on both
pumps are equal. Pump 1 should be set to 100%.
9. Start taking readings as you reduce the flow by small increments.
10. After taking the final set of data, fully open the valve gate again. DO NOT LEAVE
THE PUMP RUNNING WITH CLOSED VALVE FOR A LONG TIME!!
Report:
1. Plot a graph of total head against discharge for a single pump and for two pumps
connected in series, both at 100%.
2. Calculate the head gain by connecting 2 pumps in series.
3. Which would be the reason to connect 2 pumps in series?
4. Plot a graph of total head against discharge for a single pump and for two pumps
connected in parallel, both at 100%.
5. Calculate the flowrate gain by connecting 2 pumps in parallel.
6. Which would be the reason to connect 2 pumps in parallel?
7. Compare the graphs for pumps in series and in parallel, and describe the similarities
and/or differences.