a)ASTM A 53 b)ASTM A 106 c)ASTM A 333 d)All of the above
Ans. b
2.What is the mills tolerance to be considered for the thickness calculation of smls pipe as per ASME B31.3 a)12 b)12.25 c)12.5 d)None of the above
Ans. c
3.Butt welded fittings (upto 600#) are generally used in which Size range a)1/2 & above b)2 & above c)Both a & b d)None of the above
Ans. b
4.ASME B16.10 describes about a)Face to face & end to end dimensions of non-ferrous valves b)Face to face & end to end dimensions of ferrous valves c)Both a & b d)None of the above
Ans. b
5.ASTM Std. for 6 C.S welded pipe is a)A106 Gr.B b)A53 Gr.B c)API 5L Gr.B d)All of the above
Ans. b
6.ASTM Std. for 8 C.S 150# flange a)A234Gr WPB b)A216Gr WCB c)A105 d)None of the above
Ans. c
7.Usually the ASTM Std. for 30 L.T.C.S. EFW pipe is a)A333 Gr.6 b)A106 Gr.B c)A671 Gr.CC60 Cl.32 d)All of the above
Ans. c
8.Which of the fluid Service is non-toxic in nature? a)Category D b)Category M c)High Pressure fluid service d)Normal fluid service
Ans. a
9.All Pipe bends in CS are ____________ a)hot formed b)cold formed c)both a & b d)none of the above
Ans. b
10.What is the Size range in NPS for ASTM A106 Smls.Pipe a)1/8 to 46 b)1/8 to 44 c)1/8 to 48 d)None of the above
Ans. c
11.What is the dmn.std. for S.B. gate valve? a)API-602 b)API-600 c)API-609 d)None of the above Ans. a 12.What is the dmn.std. for L.B. gate valve? a)API-602 b)API-600 c)API-609 d)None of the above
Ans. b
13.What is the dmn.std. for S.B. globe valve? a)BS-5351 b)BS-5352 c)BS-1873 d)API-602
Ans. b
14.What is the dmn.std. for L.B. globe valve? a)BS-5351 b)BS-5352 c)BS-1873 d)API-602
Ans. c
15.What is the dmn.std. for check valve? a)BS-5352 b)BS-1868 c)BS-1873 d)Both a & b
Ans. d
16.What is the dmn.std. for Ball valve? a)BS-5351 b)BS-5352 c)BS-1873 d)None of the above
Ans. a
17.Steam pipe lines are usually _________________ a)ERW b)EFW c)Seamless d)None of the above Ans. c 18.Low temp. carbon steel shall be used below which temp. in 0C a)-20 b)-30 c)-29 d)-40
Ans. c
19.What is the std. used for Welded and seamless wrought steel pipe? a)ASME B36.10 b)ASME B36.19 c)ASME B16.11 d)ASME B16.9
Ans. a
20.Small bore fitting are covered under which American std.? a)ASME B36.10 b)ASME B36.19 c)ASME B16.11 d)ASME B16.9
Ans. c
21.Large bore fittings are covered under which American std.? a)ASME B36.10 b)ASME B36.19 c)ASME B16.11 d)ASME B16.9
Ans. d
22.Which Std. is used for large dia. flanges ? a)ASME B16.5 b)ASME B16.47 c)ASME B16.48 d)None of the above
Ans. b
23._________is used as the fitting material in LTCS for Sizes usually 2 & above a)ASTM A420 Gr.WPL6 b)ASTM A350 Gr.LF2 c)Both a & b d)None of the above Ans. a
24._________is used as the fitting material in LTCS for Sizes usually 11/2 & below a)ASTM A420 Gr.WPL6 b)ASTM A350 Gr.LF2 c)Both a & b d)None of the above
Ans. b
25._____________ is a non-return Valve. a)Gate Valve b)Globe valve c)Ball Valve d)Check Valve
Ans. d
26.What is the dmn.std. for Plug valve? a)BS-5352 b)BS-5351 c)API-599 d)API-602
Ans. c
27._________ is the maximum temp. till which Carbon Steel can be used as per B31.3 a)4200C b)4290C c)4250C d)4270C
Ans. c
28._________ is the minimum temp. till which Carbon Steel can be used as per B31.3 a)-300C b)-280C c)-450C d)-290C
Ans. d
29.Under which p group is Carbon Steel Considered? a)1 b)3 c)6 d)7
Ans. a
30.Generally _____________ is used as a by-pass Valve a)Gate Valve b)Butterfly Valve c)Ball Valve d)Globe Valve
Ans. d
31.Types of Ball Valve: a)Full Port b)Regular Port c)Soft Seat & Metal Seat d)All of the above
Ans. d
32.Types of Check Valve: a)Lift type b)Swing type c)Wafer type d)All of the above
Ans. d
33.Gate & Ball Valve are ________________ valves a)Isolating b)Regulating c)Non-return d)None of the above
Ans. a
34.Globe Valve is a ________________ valve a)Isolating b)Regulating c)Non-return d)None of the above Ans. b
35.What is the minimum thickness required for CS pipe which needs PWHT requirement? a)18 mm b)20 mm c)19 mm d)21 mm