RENOVATION OF 6TH FLOOR, ISBT, KASHMERE GATE, DELHI
Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting works Rate in Rs. Amount in Rs. in figures in words SH-1.00 DISMANTLING WORK 1.1 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge. 15.7.4 In cement mortar Cum 135 1.2 15.2.1 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.(a) 1:3:6 or richer mix. Cum 42 1.3 15.12.1 Dismantling doors, windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete andstacking within 50 metres lead Each 18 Item No DSR Ref Description Unit Qty Page 1 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty SH-2.00 FLOORING WORK 2.1 11.36 Providing and fixing Ist quality ceramic glazed walls tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. Sqm 108 2.2 11.38 Providing and laying Ceramic glazed floor tiles 300x300 mm(thickness to be specified by the manufacturer) of Ist quality conforming to IS:15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement:4 Coarse sand) including grouting the joints with white cement and matching pigments etc.complete Sqm 40 2.3 11.41.2 Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Sqm 415 Size of Tile 60x60cm 2.4 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to Floor five Level cum 9 Page 2 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 2.5 8.2 Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. 8.2.2 Granite of any colour and shade 8.2.2.1 Area of slab upto 0.50 sqm Sqm 25 SH-3.00 BRICK WORK 3.1 6.4.2 Brick work with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6( 1 cement: 6 coarse sand) cum 75 3.2 6.13.2 Half brick masonry with F.P.Sbricks of class designation 75 in super structure above plinth level upto floor V level. Cement mortar 1:4( 1 cement : 4 coarse sand) sqm 30 SH-4.00 RCC WORK Page 3 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 4.1 5.3 Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15 landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiralstair cases up to floor five level excluding the cost of centering,shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size). Cum 11 4.2 5.22.3 Reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete.Cold twisted bars kg 1000 4.3 Centering and shuttering including strutting, propping etc. and removal of form for 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 50 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. sqm 40 5.9.16.1 Edges of slabs and bracks in floors and walls (a) Under 20Cms wide. Metres 28 SH-5.00 FINISHING WORK 5.1 13.4 12 mm cement plaster of mix : 13.4.1 1:4 (1 cement: 4 coarse sand) sqm 325 Page 4 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 5.2 13.5 15 mm cement plaster on rough side of single or half brick wall of mix : 13.5.1 1:4 (1 cement: 4 coarse sand) sqm 325 5.3 13.16 6 mm cement plaster of mix : 13.16.1 1:3 (1 cement: 3 fine sand) sqm 50 5.4 13.42 Distempering with 1st quality acrylic washable distemper (ready mixed) of approved manufacturer and of required shade and colour complete as per manufacturer's specification 13.42.1 Two or more coats on new work. sqm 610 5.5 13.68 French spirit polishing : 13.68.1 Two or more coats on new works including a coat of wood filler sqm 150 5.6 13.62 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. sqm 120 SH-6.00 WOOD WORK Page 5 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 6.1 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: 9.1.1. Second class teak wood Cum 3 6.2 9.3 Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position: 9.3.2 Kiln seasoned and chemically treated Hollock wood. Cum 8 6.3 9.11 Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shuttrs.(Area of oepning for glass panes exluding portion inside rebate shall be measured) 9.11.1 5.5mm thick instead of 4mm thick Sqm 28 6.4 9.35 Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre- laminated one side decorative lamination on other side balancing lamination Grade 1, Type II, IS:12823 marked including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete. 9.35.1 12mm thick Sqm 610 6.5 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete Page 6 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.74.1 250x10 mm each 22 9.74.4 100x10 mm each 22 6.6 9.76 Providing and fixing bright finsihed brass 100mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality) each 22 6.7 9.82 Providing and fixing bright finsihed brass hanging type floor door stopper with necessary screws, etc. complete each 22 6.8 9.101 Providing and fixing aluminium hanging floor door stopper ISI on marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparant or dyed to required colour and shade with necessary screws etc. complete 9.101.2 Twin rubber stopper each 18 6.9 9.20 Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part 1) decorative type, core of block baord construction with frame of Ist class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.2 30mm thick including ISI marked Stainless Steel butt hinges with necessary screws. Sqm 42 Page 7 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 6.10 12.45 Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall partition with the help of rawl plungs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitably for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitable fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting with Page 8 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 12.45.1 12.5mm thick tapered edge gypsum board conforming to IS:2095-Part 1. Sqm 410 6.11 Providing and fixing 100 mm wide vertical venation blinds polyster fabric lourers linked to each other with wane chain and hanged with PVC hooks sliding on aluminium guide rail, the control handles attached to high strength polyster handle fibre cord shall be moulded type and to be made of steel ball chain, at the bottom of lourers shall be of a glavanised steel plate duly powder coated including fixing to galvanized steel bracket on the top, all complete Sqm 20 6.12 Disposal of malba, building rubbish etc. by mechanical transport including loading, unloading and stacking for all leads and lift complete as per direction of Engineer-in-Charge Cum 200 6.13 Providing and fixing UPVC panelled and glazed doors & windows with frames. Glazing with 5mm thick float glass on both sides and pre-laminated board of 6mm thick in bottom inside panel including fittings and fixtures insulation material etc complete. The window material should have the property of with acoustic insulation, thermal insulation,water tight, fire resistant, termite resistant as per ISI/ BS specification of required shape, size and design as per approval of Engineer-in- charge. Sqm 82 6.14 10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete kg 810 Page 9 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty SH-7.00 ALUMINIUM WORK 7.1 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC /neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing and panelling to be paid for separately) 21.1.1 For fixed portion 21.1.1.1 Abodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Kg 23 7.2 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately) 21.1.2.1 Abnodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15) Kg 45 Page 10 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 7.3 21.2 Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle boqard conforming to IS:12823 Grade 1 Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete as per architectual drawings and directions of engineer-in-charge. 21.2.2. Pre-laminated particle board with decorative lamination on both sides. Sqm 4 7.4 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge (Cost of aluminium snap beading 21.3.2 With float glass panes of 5.50 mm thickness Sqm 4 7.5 21.4 Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S sheet outer box with slide plate etc. complete as per the direction of Engineer- in-charge 21.4.1 With stainless steel cover plate each 4 Page 11 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 7.6 21.8 Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete 21.8.1 Upto 5mm depth and 5mm width metre 240 7.7 21.12 Providing and fixing aluminium tubular handle bar 32mm outer dia 3.0 mm thick & 2100 mm long with SS screws ect. Complete as per direction of Engineer- in -Charge 21.12.1 Anodized (AC 15) aluminium tubular handle bar each 8 7.8 21.13 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete each 2 Page 12 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty SH-8.00 SANITARY AND WATER SUPPLY 8.1 Water closed-p/fixing wall mounted european type W.C pan Hindware make along with cast iron wall cantilever brackets ,with seat cover,installing/connecting into S.C.I pipe,water supply,p/fixing concealed cistern and all connection complete as per specification and direction of engineer in charge(sample can be seen for the same in DIMTS office). each 4 8.2 Providing and fixing hindware riva urinal with censor attachment within it etc. complete as per specification and approval of Engineer in charge (sample can be seen for the same in dimts office). each 2 8.3 P/F (hindware make kathy) rectangular wash basin fixed into counter including CP waste coupling with rubber plug, bottle trap with long wall connection pipe and CP inlet connection as per specification and aprroval of E in charge.(sample can be seen for the same in dimts office). each 4 8.4 Providing and fixing Stainless Steel A ISI 304(18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510x1040mm bowl depth 250mm each 0 Page 13 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 8.5 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing. Rectangular shape 1500x450mm each 2 8.6 Providing and fixing toilet paper holder CP brass each 4 8.7 Urinal partitions , providing and fixing merino modesty pannels as per specification and approval of Engineer in charge.(sample can be seen for the same in DIMTS office). each 1 8.8 Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. each 2 8.9 Angle cock: P/F Jaguar- florentine series heavy body CP complete as per specification and approval of E in charge. each 8 8.10 Pillar Cock: P/F Jaguar PRESSMATIC series heavy body CP make pillar cock with adjustable wall flange etc . Complete as per specification and approval of Engineer in charge. each 4 8.11 Jet spray: P/F hand shower (Health faucet with 8 mm dia 1 meter long PVC tube wall hook etc . Complete (make Jaguar "florentine") as per specification and approval of Engineer in charge. each 4 Page 14 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 8.12 17.35 Providing and fixing soil, waste and vent pipes : 17.35.1 100 mm dia. 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729. metre 50 8.13 17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. 17.37.1 For 100 mm dia. Pipe each 10 8.14 17.41 Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 17.41.1 100x100x100x100mm 17.41.1.1 Sand cast iron S&S as per IS - 1729 each 3 8.15 17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 17.58.1 100 mm each 25 8.16 P/F CP brass Jali for floor traps 100 mm. each 5 Page 15 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 8.17 Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall 18.11.1 15 mm dia nominal bore metre 50 18.11.2 20 mm dia nominal bore metre 70 8.18 22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. sqm 42 8.19 Granite Counter ( toilet and pantry) : P/F counter made out of 25 mm thick granite ( of approved colour & shade supported by 20 mm thick Kadappa horizontally and 12 mm thick.Sandwiched Kaddappa vertically at intervals as per specification and approval of engineer in charge. Sqm 4 Page 16 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 8.20 Below Counter Storage: P/Constructin 1 mm thick laminate shutters for electrical pannels ,toilet and pantry counter platform area with 3/4" thick marine ply of Anchor/Kit ply or Kenwood make with 3/4" * 2 " Teak wood frame, shutter to include. sqm 3 SH: 9.00 FURNITURE 9.1 MR Supply of table of size 1800x900x750mm using 25mm thick post form top and rest 18mm thick pre laminated particle board, PVC side edge with all fittings and fixtures complete as per direction of Engineer-in-charge including Each 8 (i) Pedestal unit of size 450x450x715mm(ht) under the table made of 25mm thick post form top and rest 18mm thick pre-laminated particle board with two equal drawers and one filling drawer with centralized locking and castors duly powdered coated in/c all fittings & fixtures complete. (ii)Side Storage: 1200x450x725mm (ht) using 25mm thick post form top and rest 18mm thick pre laminated particle board with PVC side edge bidding, metal key board tray(pull out type (iii) CPU trolley with W-180mm, D-245mm, H- 210mm made up of press formed MS CP sheet 1.6mm thick with adjustable width, rubber pads inside the trolley for the safety of CPU in/c castors and brakes with fittings and fixtures complete. Page 17 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.2 MR Supply of table of size 1500x750x750mm using 25mm thick post form top and rest 18mm thick pre laminated particle board, PVC side edge with all fittings and fixtures complete as per direction of Engineer-in-charge including Each 14 (i) Pedestal unit of size 450x450x715mm(ht) under the table made of 25mm thick post form top and rest 18mm thick pre-laminated particle board with two equal drawers and one filling drawer with centralized locking and castors duly powdered coated in/c all fittings & fixtures complete. (ii)Side Storage: 900x450x725mm (ht) using 25mm thick post form top and rest 18mm thick pre laminated particle board with PVC side edge bidding, metal key board tray(pull out type, (iii) CPU trolley with W-180mm, D-245mm, H- 210mm made up of press formed MS CP sheet 1.6mm thick with adjustable width, rubber pads inside the trolley for the safety of CPU in/c castors and brakes with fittings and fixtures complete. 9.3 MR Suppl of work station table of size 1500mm x 750mm x 750mm, with key board tray, expendable CPU trolly (Metal), Pedestal unit under the working top using 25mm thick post form top and rest 18mm thick pre-laminated particle board as per specification of key board tray(Pull out type), CPU Trolley & Pedestal unit are given below with all fixture and fittings, as per direction of Engineer-in-charge. Each 7 Page 18 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty (i) Pedestal unit of size 450x450x715mm(ht) under the table made of 25mm thick post form top and rest 18mm thick pre-laminated particle board with two equal drawers and one filling drawer with centralized locking and castors duly powdered coated in/c all fittings & fixtures complete. (ii) CPU trolley with W-180mm, D-245mm, H- 210mm made up of press formed MS CP sheet 1.6mm thick with adjustable width, rubber pads inside the trolley for the safety of CPU in/c castors and brakes with fittings and fixtures complete. 9.4 MR Supply of storage unit of height 750mm and depth 450mm using 25mm thick post form top and rest 18mm thick pre- laminated particle board for partitions storage, doors etc. with PVC side edge beading and all fittings & fixtures complete as per direction of Engineer-in-charge( Note : Area of storage shall be calculated length multiplied by height of storage) sq.m 30 Page 19 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.5 MR Providing and fixing modular partition 69mm thick ( 4mm) made of M S profile 38x38mm. Medium horizontal profiles shall run parallel inside the partition at 600mm centre to centre and verticle profiles shall be provided 750mm centre to centre or as per site requirement with provision of horizontal slots for taking wires as required. All M.Sprofiles shall be powder coated. Both sides of partition frame shall be covered with 12mm thick pre laminated particle board/ fabric mounted on soft board /partly with 5.5mm thick frosted float glass at top of required height over particle board partitions as required at site the particle board shall be attached to the partition frame with clips on the rear side. The end of vertical member as well top member of partition shall be fixed / covered with powder coated aluminium member of 72mm wide and 1.8mm thick complete as per direction of Engineer-in-charge. Sqm 115 9.6 MR Supply of high back chair, CRC steel frame, padding Nivar & Hellical springs, centre tilt, gas lift, Wooden Arms, Upholstery in fabric/leatherite top quality of approved shade and design, cushion made of 60mm thick PU foam as per specificationsas under and direction of Engineer-in-charge Overall Size: W-700mm, D-700mm, H-1060 to 1100mm Adjustability of seat height 450mm to 540mm Seat size:520x530mm (approx.) Back size:480x520 (ht.) (approx.) Each 10 Page 20 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty Material of seat and back should be made up of 12mm thick hot pressed ply wood, moulded polyurethane foam with density 60, together with moulded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. The seat and back are to be covered with vacuum foam from 3mm thick black ABS sheet. The chair should have forward tilt, required board tilt with tilt locking and anti shock back mechanism with wooden arms. The twin wheel castors should be injected moulded in black Nylon and having 5 prongs are powder coated/chrome plated base. 9.7 MR Supply of medium back chair, CRC steel frame, padding Nivar & Hellical springs, centre tilt, gas lift, Wooden Arms, Upholstery in fabric/leatherite top quality of approved shade and design, cushion made of 60mm thick PU foam as per specificationsas under and direction of Engineer-in-charge Overall Size: W-700mm, D-700mm, H-925mm to 975mm Adjustability of seat height 450mm Seat size:520x530mm (approx.) Back size:480x580mm (ht.) (approx.) Each 24 Page 21 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty Material of seat and back should be made up of 12mm thick hot pressed ply wood, moulded polyurethane foam with density 60, together with moulded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. The seat and back are to be covered with vacuum foam from 3mm thick black ABS sheet. The chair should have forward tilt, required board tilt with tilt locking and anti shock back mechanism with wooden arms. The twin wheel castors should be injected moulded in black Nylon and having 5 prongs are powder coated/chrome plated base. 9.8 MR Supply of medium back chair, CRC steel frame, padding Nivar & Hellical springs, centre tilt, Wooden Arms, Upholstery in fabric/leatherite top quality of approved shade and design,cushion made of 40mm thick PU foam as per specificationsas under and direction of Engineer-in-charge Overall Size: W-700mm, D-700mm, H-925mm to 975mm Adjustability of seat height 450mm Seat size:460x460mm (approx.) Back size:430x520mm (ht.) (approx.) Each 18 Page 22 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty Material of seat and back should be made up of 12mm thick hot pressed ply wood, moulded polyurethane foam with density 40, together with moulded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. The seat and backs are to be covered with vacuum foam from 3mm thick black ABS sheets. The chair should have forward tilt, required board tilt with tilt locking and anti shock back mechanism with wooden arms. The twin wheel castors should be injected moulded in black Nylon and having 5 prongs are powder coated/chrome plated base. Page 23 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.9 MR Supply of low back chair, CRC steel frame, padding Nivar & Hellical springs, centre tilt, Nylon base PU arms, Upholstery in fabric/leatherite top quality of approved shade and design, cushion made of 40mm thick PUfoam.as per specificationsas under and direction of Engineer-in-charge Overall Size: W-700mm, D-700mm, Adjustability of seat height 450mm Seat size:460x460mm (approx.) Back size:430x340mm (Ht.)(approx.) Material of seat and back should be made up of 12mm thick hot pressed ply wood, moulded polyurethane foam with density 40, together with moulded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. The seat and backs are to be covered with vacuum foam from 3mm thick black ABS sheets. The twin wheel castors should be injected moulded in black Nylon and having 5 prongs are powder coated/chrome plated base. Each 40 Page 24 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.9 MR Supply of 3(three) seater, 2(two) seater, single seater sofa with arms of size 2020mm (W)x750mm (D)x750mm(H) and seat height 400mm for 3 seater, 1420mm (W)x750mm(D)x750mm(H) for 2 seater and 1020mm(W)x 750mm(D)x 750mm(H) for single seater with arms height 590mm. The sofa structure is to be made of 45mmx28mm finished Teak wood section with flat vertical springs and 90mm thick 40 density PU foam with topping of 20mm super soft foam, back is to be made with 45mm thick 32 density PU foam with topping of 20mm super soft foam . Armed structure is to be made with 120x28mm teak section for top and vertical, 95x28mm for bottom. Arms are to be covered with 20mm thick 28 Each 2 foam all side.Armed and back loose cushion are mde of 45mm thick 32 density PU foam with legs made out of 70x70mm teak section in round shape with 45mm height and good quality tapestry/leatherite, malemine polish etc. or as per size required at site with all fittings and fixtures. Complete as per direction of Engineer-in- charge 9.10 Supply of Center Table of size 1200x600x450mm made of teak wood duly spirit polish with 75x75mm teak wood legs and 12mm thick bevelled edge glass top or18mm thick pre laminated MDF board lipping the edge banding of pre glued tape of same shade by hot process or as per the design approved by Engineer in-charge Each 1 Page 25 of 26 Rate in Rs. Amount in Rs. in figures in words Item No DSR Ref Description Unit Qty 9.11 MR Supply of Conference Table of required shape of over all size 3600x1200x750mm(ht) comprising with three units of size 1200x1200x750mm (ht) using 25mm thick post form pre laminated particle board top supported with metal powder coated legs/chrome plated in approved shade with necessary fittings and fixtures complete as per directions of Engineer-in-charge. All the four corners should be covered with half round top and all the tables are to be covered with front panels. Each 1 TOTAL Page 26 of 26 BILL OF QUANTITIES - ELECTRICAL WORKS RENOVATION OF 6TH FLOOR, ISBT, KASHMERE GATE, DELHI Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting works Rate in Rs. Amount in Rs. in figures in words SUB HEAD :- A, INTERNAL WIRING I POINT WIRING 1.0 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. GROUP-C 172 Point 2.0 Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. 2 Point 3.0 Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 350 Meter 4.0 Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 300 Meter 5.0 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc. as required. (For light plugs to be used in non residential buildings). 48 Each Item No Description Qty Unit Page 1 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit 6.0 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. 19 Each 7.0 Supplying and fixing call bell/ buzzer suitable for D.C./A.C. single phase, 230 volts, complete as required. 0 Each 8.0 Supply and fixing fan box (hexagonal type) as per drg. Attached 75 mm side 75mm deep made of 16 SWG M.S. sheet having 6 Nos. knockouts of size 20/25 mm for conduit entry including fan hook made of 12mm M.S. Rod with bottom cover of 3mm thick phenolic laminated sheet, painting etc. as required. 22 Each II CIRCUIT /SUBMAIN WIRING 1.0 Wiring for circuit/ submain wiring alongwith earh wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 750 Meter b) 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire 20 Meter c) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire 20 Meter d) 4 X 10 sq. mm + 2 X 10 sq. mm earth wire 20 Meter SUB HEAD-B: LUMINARIES AND FIXTURES I SUPPLY OF LUMINARES 1.0 Supply of the following luminaires complete in all respects a) LED Strip light, Instapower Slim sparkle 8W or equivqlent 70 m b) LED ceiling light 45W, Instapower Milkyway or equivalent 8 Nos c) LED Downlighter 11W, Instapower D-Lite 119 Nos Page 2 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit d) Attractive wall mounted light fixture with 1x PL -S 11 W CFL lamp. Philips Cat No. FMC 170/111 or equivalent. 0 Nos II SUPPLY OF CEILING/ PROPELLER TYPE EXHAUST FANS (WITH GRAVITY LOUVERS) / CABIN FAN. a) 1200 mm sweep Ceiling fan. 22 Nos b) 300 mm dia 900 RPM exhaust fan. 2 Nos d) Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 22 Each III INSTALLATION OF LUMINARIES AND FIXTURES a) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. 148 Each b) Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 22 Each c) Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required. 2 Each d) Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 2 Each SUB HEAD -C, DISTRIBUTION BOARDS I DISTRIBUTION BOARDS Page 3 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit 1.0 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 4 way (4 + 12), Double door, horizontal type 1 Each b) 6 way (4 + 18), Double door, horizontal type 1 Each c) 8 way (4 + 24), Double door, horizontal type 2 Each 2.0 Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) Single Pole 78 Each 3.0 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 20 Each 4.0 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) 63 A 4 Each SUB HEAD - D :- TELEPHONE / TV & DATA SYSTEM 1.0 Supplying and drawing following pair, 0.5 mm dia FR PVC insulated copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. a) 2 Pair 1000 Meter Page 4 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit 2.0 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 25 Meter 3.0 Supplying and fixing of following sizes of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. a) 20 mm. 200 Meter b) 25 mm. 600 Meter 4.0 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. a) Telephone socket outlet. 22 Each b) TV antenna socket outlet. 1 Each 5.0 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. a) 1 or 2 Module (75mm x 75mm) 45 Each 6.0 Supply and fixing following Data /Lan modular socket on the existing modular plate including connections but excluding modular plate etc. as required. a) RJ - 45 Socket. 22 Each 7.0 Supply of UTP Cat 6 Data /Lan wiring cable for computer communication (Data / Lan wiring) system in the existing surface / recessed steel / PVC conduit as required. a) 1 No. 900 Meter Page 5 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit 8.0 Supply and fixing of the following Telephone Tag Block made out of M.S sheets of 18 SWG thickness properly welded complete with all accessories such as Tag block, connector (KRONE make), mounting strips, tapped holes, fixing bolts, approved shad of paint after primer as per specifications. a) 50 Pair 1 Nos. b) 10 Pair 1 Nos. 9.0 Supply & fixing of 14 SWG under floor box alongwith 10SWG stainless steel cover plate. a) 350 x 350 x 50 mm deep 1 Nos. b) 300 x 300 x 50 mm deep 1 Nos. c) 250 x 250 x 50 mm deep 1 Nos. d) 200 x 200 x 50 mm deep 1 Nos. e) 150 x 150 x 50 mm deep 1 Nos. f) 100 x 100 x 50 mm deep 1 Nos. SUB HEAD - E , L.T. PANELS (SUPPLY AND INSTALLATION) 1.0 L.T. PANELS : Page 6 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit 1.1 Supply of the following cubical type panels made of 14 guage CRCA structure, base channel, complete with, moulded case circuit breakers, meters, indicating lamps, current transformer etc. Complete in all respects, insulated bus bars with heat shrinkable PVC sleeve in suitable bus chambers, interconnection, small wiring, name plate, danger plat, earth bus etc. & comprising of compartments with hinged door for each feeder & its accesories, cable alley with hinged doors, bus chamber with bolted door etc. The panel being of dust & vermin proof construction with rubber gasket attractively powder coating etc. The panel shall be free standing type/ wall mounted type as per relavant drawing and comprising with the following. Note:- 1 All MCCBS shall be with operating handle. 2 CTs burden shall be 15VA & accuracy class 1.0 3 CTs shall be cast resin type . 4 All MCCBs shall be with thermal magnetic/ Microprocessor based releases. 5 All indication lights shall be LED type. 6 All meter shall be digital type. 7 Rated Short Time withstand current of all MCCB's are Icw for one second. 8 Breaking Capacity of all MCCB's are Ics service breaking capacity A) MAIN L. T. PANEL (MLTP) a) INCOMING : i) 2 Nos.200A TP MCCB (35kA) 1No. 200A Changeover b) BUS BAR : i) One set of 300A Alu. Bus Bar with PVC Sleeve in sealed M.S. Painted bus chamber. c) METERING , INDICATIONS AND RELAYS : i) 1 set. of R/ Y/ B phase indicating lamp with control MCB's. ii) 1 No. (0 - 300A) Digital Ammeter with built- in selector switch and CT's. iii) 1 No . (0 - 500 V) Digital Voltmeter with built-in Selector switch & control MCB's. d) OUT GOINGS : i) 2 Nos. 100A, TP MCCB (25 kA) ii) 6 Nos. 63A, 4P MCB (10 kA) 1 Set Page 7 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit e) ON-OFF indication lamps shall be provided on all outgoing feeders f) 1 No. 50 x 6mm Aluminium Earth Bus across the width of the panel. B) MAIN UPS PANEL BOARD i) INCOMING : ii) 1 No.100A, TP MCCB (25 kA) ii) BUS BAR : i) One set of 100A TPN Cu. Bus Bar with PVC Sleeve in sealed M.S. Painted Bus Chamber.(Neutral Bus Bar & Neutral links of MCCB's shall be double of phase bus bar) iii) INDICATIONS : i) One set of R/Y/B phase indication lamp with control fuse. iv) OUTGOING : i) 3 Nos 63 A TP MCCB (10kA) g) 1 No. 40 x 5 mm Aluminium Earth Bus across the width of the panel. SUB HEAD - F , L.T. CABLES 1.0 L.T. CABLES (SUPPLY) 1.1 Supply of the following 1100 Volts Alu/ Cu. Conductor, PVC insulated PVC sheathed, steel armoured/ unarmoured or XLPE cables as per IS- 1554/ 7098 Part- I and as per stanard specification A) ALUMINIUM CABLE (ARMOURED) a) 3.5 core 185 sq.mm XLPE 150 RM b) 4 core 50 sq.mm PVC 30 RM B) COPPER CABLES (ARMOURED) a) 4 core 10 sq. mm. 50 RM b) 4 core 6 sq. mm. 15 RM 1.0 L.T. CABLES (INSTALLATION) 1.1 Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE Aluminium / Copper conductor cable of 1.1 KV grade on surface as required. A) ALUMINIUM CABLE (ARMOURED) a) 3.5 core 185 sq.mm XLPE 150 RM b) 4 core 50 sq.mm PVC 30 RM B) COPPER CABLES (ARMOURED) 1 Set 1 Set Page 8 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit a) 4 core 10 sq. mm. 50 RM b) 4 core 6 sq. mm. 15 RM 2.0 CABLE END TERMINATIONS 2.1 Supply & provide cable end terminations for following Aluminium/Copper conductor cables using crimping sockets, brass compression glands, etc, as required. A) ALUMINIUM CABLE (ARMOURED) a) 3.5 core 185 sq.mm XLPE 2 Nos b) 4 core 50 sq.mm PVC 2 Nos B) COPPER CABLES (ARMOURED) a) 4 core 10 sq. mm. 10 Nos b) 4 core 6 sq. mm. 4 Nos SUB HEAD - G , EARTHING & MISCELLANEOUS ITEMS 1.0 TAPES/WIRES Supplying, receiving, laying, fixing, jointing, and terminating of the following tapes/wires in masonry treches/on walls/on cable tray/ along the cable with suitable G.I./Copper Clamps, screws etc. The wire shall be terminated with proper thimbles, washers, bolts & nuts. All joints shall be regid using double rivites : a) 40 x 5 mm GI Tape 50 RM b) 1Core x 6 mm CU Flexible wire 20 RM c) 1Core x10 mm CU Flexible wire 20 RM 2.0 EARTH STATIONS: 2.1 Providing and fix following earth station as per IS 3043-1987, with watering pipe, GI funnels masonry chamber with CI cover, Including excavation and refilling of pit, supplying and fixing of charcoal salt & sand, identification of pit as as required. Page 9 of 10 Rate in Rs. Amount in Rs. in figures in words Item No Description Qty Unit a) 600 x 600 x 3.15 mm Copper Plate Earth Station 1 Nos. b) 600 x 600 x 6.00 mm GI Plate Earth Station 1 Nos. TOTAL Page 10 of 10 BILL OF QUANTITIES - FIRE FIGHTING WORKS RENOVATION OF 6TH FLOOR, ISBT, KASHMERE GATE, DELHI Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting works Rate in Rs. Amount in Rs. in Rs. in figures in words 1 Supply,installation and commissioning of semi concealed pendant type sprinkler 68C complete with crome steel sliding type rosette in the existing network including M.S pipe of 15 mm dia sized upto 1.5 m length as required including fittings consumable etc. complete. each 20 2 Supply,installation and commissioning of optical smoke detector standard design with wall mounting based in the existing fire alarm system complete (agni or system sensor make). each 60 3 Supply, installation and commissioning of response indicator on ceiling / walls ,including connections etc. in the existing fire alarm system complete (agni or system sensor make). each 40 4 Supply, installation and commissioning of copper conductor PVC insulated heavy duty armoured cable of havell make as per approval of Engineer in charge The following sizes a)2*1.5 sqmm metres 200 b)4*1.5 sqmm metres 35 5 Supply, installation and commissioning of sounder (hooter) standard make (such as agni or system sensor make) in the existing fire alarm system each 2 6 Supply, installation testing and commissioning of manual call boxes complete of standard make (agni or system sensor make) with hammer and chain including connection etc.as required each 8 7 P/F G.I. pipes complete with G.I. fittings and clamps including cutting and making good the walls a)15mm nominal bore metres 25 b)25mm nominal bore metres 10 8 Dismentling of existing 25 mmMS pipes& refixing the same after making necessary adjustment in sprinklers including testing of sprinklers complete as per the direction of engineer-in-charge. metres 25 Item No DSR Ref Description Unit Qty Page 1 of 1