BITMINOS P!INTIN" ON CONCRETE/ M!SON!R# SR$!CES. BITMINOS P!INTIN" ON CONRETE/ M!SON!R# SR$!CES. 1.0 PRPOSE The purpose of this procedure is to describe & define a method for carrying out bituminous painting on concrete/ masonary surfaces at sites. 2.0 SCOPE This procedure shall be applicable for all types of bituminous painting/ coating on concrete/ masonary surfaces undertaken by the Company. 3.0 RE$ERENCE 3.1 Q!"0#0 $ocument & $ata Control. 3.2 Q!"100 %nspection & Testing. &.0 %E$INITIONS &.1 Company '(). &.2 Quality *ngineer +ominated Quality *ngineer at ,ite. &.3 !ro-ect *ngineer Company designated !ro-ect leader as decided by the .anagement and assigned /ith the responsibility of managing the !ro-ect. &.& 0ituminous coating 0itumen emulsion consisting of bitumen1 rubber late2 to 3aried ratio /hich dries to pro3ide a tough & fle2ible coating. #.0 PROCE%RE #.1 Responsibility #.1.1 The responsibility for carrying out this .ethod ,tatement shall be that of the !ro-ect *ngineer1 unless other/ise specifically mentioned in this procedure. The Quality *ngineer/ !ro-ect *ngineer shall be responsible for inspection & testing. #.2 Typical uses C%4%5 .,T6 010/ 7*4 0 $ate8 9anuary 2:1 2001 Xyz COMPANY Method Statement CIVIL NO.: CIVIL MST- 010/ REV 0 Page & of 3 TITLE:
BITMINOS P!INTIN" ON CONCRETE/ M!SON!R# SR$!CES. #.2.1 The cold applied 0ituminous emulsion can be used for the follo/ing applications if not specified or as per Contract specifications/ or as agreed /ith the Quality *ngineer. /aterproof membrane for concrete and brick foundations1 retaining /alls etc. s /aterproofer for floor1 /alls including /et areas %.e. floors of bathrooms1 kitchens1 balconies etc. s a 3apour/ salt barrier to building facades behind granite1 marble and stone cladding1 curtain /alling1 etc. s a protecti3e coating and 3apour barrier to surfaces behind false ceiling1 bulk heads and other areas. #.3 Environmental conditions #.3.1 *nsure that the atmospheric conditions are conduci3e for application of the 0ituminous painting/ coating as follo/s8 There should be no rain1 mist or fog. The application temperature shall be from # degree to #0 degree if not specified or as per Contract specifications/ .anufacturer;s instructions or as agreed /ith the Quality *ngineer. The en3ironment should be dust free. #.& Surface preparation #.&.1 *nsure that the surface is sound1 stable. #.&.2 *nsure that the surface is free from dust1 dirt1 grease1 oil and loose matter. #.&.3 *nsure that the surface is not /ater logged. #.&.& *nsure that the surface is de3oid of holes and cracks and the holes are filled /ith appropriate filled material as per Contract specifications/ .anufacturer;s instructions or as agreed /ith the Quality *ngineer. #.# Paint Application #.#.1 The paint shall be applied /ith a brush1 roller or as per Contract specifications/ .anufacturer;s recommendations. #.#.2 The painting system and the application shall be as per Contract specifications/ .anufacturer;s recommendations. #.#.3 The paint shall be stirred /ell before use. #.#.& *nsure that the good 3entilation is allo/ed in case of confined areas. C%4%5 .,T6 010/ 7*4 0 $ate8 9anuary 2:1 2001 Xyz COMPANY Method Statement CIVIL NO.: CIVIL MST- 010/ REV 0 Page 3 of 3 TITLE:
BITMINOS P!INTIN" ON CONCRETE/ M!SON!R# SR$!CES. #.#.# %n case of interior & e2terior applications1 minimum t/o coats shall be applied if not specificied or as per Contract ,pecifications/ .anufacturer;s recommendations. #.#.: <or multi6 coat applications1 each coat should be allo/ed to dry completely before the ne2t coat is applied. #.#.= *nsure that the application of painting coat is uniform to e3en & specificed thickness and the specified co3erage rate is attained. #.#.> The final surface should be free from drips1 runs1 bubbles or any other defects. :.0 %OCMENT!TION / RECOR%S :.1 0ituminous painting6 %nspection report C%4%5 QC"<orm6 010601/ 7*4 0. C%4%5 .,T6 010/ 7*4 0 $ate8 9anuary 2:1 2001