This document provides specifications for a precision air conditioning system, including:
- Requirements for the air conditioning unit including the frame, cabinet, cooling and fan sections.
- Descriptions of the compressors, filters, electrical reheat, steam generator, and condensing section.
- Requirements for product data, operation/maintenance documentation, quality assurance, and a two-year warranty.
Descrição original:
Título original
20140529 161455 0726 Precision Air Conditioning System
This document provides specifications for a precision air conditioning system, including:
- Requirements for the air conditioning unit including the frame, cabinet, cooling and fan sections.
- Descriptions of the compressors, filters, electrical reheat, steam generator, and condensing section.
- Requirements for product data, operation/maintenance documentation, quality assurance, and a two-year warranty.
This document provides specifications for a precision air conditioning system, including:
- Requirements for the air conditioning unit including the frame, cabinet, cooling and fan sections.
- Descriptions of the compressors, filters, electrical reheat, steam generator, and condensing section.
- Requirements for product data, operation/maintenance documentation, quality assurance, and a two-year warranty.
Archetype Specification This section is part of the Archetype Specification and should be used in conjunction with the Specification Management Procedure of the Quality Management System. Rei!ion "ritten #y Reie$e% #y& MEP De!i'n Mana'er Approe% #y& MEP De!i'n Director Effectie %ate A Maila P. bal !uynhNgoc Nghia "hab Qasem
TA()E O* CONTENTS # $"N"%A&..............................................................................................................................' #.# S(MMA%)...................................................................................................................' #.' S(*MTTA&S...............................................................................................................' #.+ Q(A&T) ASS(%AN,"...................................................................................................' #.- .A%%ANT)..................................................................................................................' ' P%/0(,TS............................................................................................................................' '.# MAN(1A,T(%"%S........................................................................................................' '.' P%",S/N A% ,/N0T/NN$ (NT.............................................................................' '.+ 1%AM" AN0 ,A*N"T...................................................................................................' '.- ,/& S",T/N.............................................................................................................' '.2 1AN S",T/N..............................................................................................................' '.3 ,/MP%"SS/%S............................................................................................................+ '.4 1&T"%S......................................................................................................................+ '.5 "&",T%,A& %"!"AT....................................................................................................+ '.6 ST"AM $"N"%AT/% !(M01"%7/PT/N8......................................................................+ '.#9 ,/N0"NSN$ S",T/N................................................................................................+ '.## M/NT/%N$ AN0 ,/NT%/&&N$ S)ST"M......................................................................+ + ":",(T/N...........................................................................................................................- +.# NSTA&&AT/N.............................................................................................................- +.' ,/NN",T/NS............................................................................................................2 +.+ 1"&0 Q(A&T) ,/NT%/&.............................................................................................2 - S,!"0(&"............................................................................................................................2 %e;ision 9< 0ate= Specifications 94'3 Precision air conditioning system Page #>2 Archetype Project Name Project Phase + GENERA) +,+ S-MMARY a8 This section co;ers the specification of the precision air<conditioning for ser;er rooms or if specified in the drawings which re?uires clean air and well distributed with precisely controlled temperature and humidity for high sensible heat en;ironment. +,2 S-(MITTA)S a8 Product 0ata= 1or each unit indicated. nclude performance data in terms of capacities@ outlet ;elocities@ static pressures@ sound power characteristics@ motor re?uirements@ and electrical characteristics. b8 /peration and maintenance data. +,. /-A)ITY ASS-RANCE a8 "lectrical ,omponents@ 0e;ices@ and Accessories= &isted and labeled as defined in N1PA 49@ Article #99@ by a testing agency acceptable to authorities ha;ing jurisdiction@ and marAed for intended use. +,0 "ARRANTY a8 1urnish two year manufacturer warranty to include co;erage for complete assembly including materials and labor or as the period mentioned in the condition of contract whiche;er is greater. 2 PROD-CTS 2,+ MAN-*ACT-RERS a8 Manufacturers= Subject to compliance with re?uirements@ pro;ide products by one of the following= #. ,yber ,orp. '. 0aiAin@ nc. +. &iebert ,orp. cc -. /r e?ui;alent to the appro;al of the engineer 2,2 PRECISION AIR CONDITIONING -NIT ) "ach unit shall be a complete en;ironmental control system factory wired@ tested and specifically designed to pro;ide temperature@ humidity and dust control for computer room or telecommunications installations. The precision air< conditioners shall be either floor standing or ceiling hung type to suit drawings and construction site limitation. 2,. *RAME AND CA(INET a8 The unit shall ha;e aluminium profile structural frame for maBimum strength@ minimum weight and ease of access and assembly. Side and front panel shall be easily opened and remo;ed with ?uarter<turn fasteners allowing full access to all unit components. All panels shall include '2mm thicA fibreglass insulation with matt surface for thermal protection and sound attenuation. 2,0 COI) SECTION a8 The unit shall be designed for draw through or blow through type with large face areas for low ;elocity to reduce turbulence and pro;ide greater efficiency in the cooling and dehumidification process. The cooling coils shall be of seamless copper tubes mechanically bonded to hydrophilic coated aluminum fins for cooling performance enhancement as well as corrosion resistance and tested under water to '599 APa with compressed air. %e;ision 9< 0ate= Specifications 94'3 Precision air conditioning system Page '>2 Archetype Project Name Project Phase 2,1 *AN SECTION ) The fan shall be centrifugal forward cur;e@ double width@ double inlet blower configuration for ?uiet operation. ,eiling hung series shall ha;e direct dri;e +< speed motors for ease of change of air<flow for optimum air<change and noise le;el. The floor standing unit shall be a belt dri;e system. The blowers shall be AM,A certified and factory certified dynamically balanced. The motor shall be totally enclosed and mounted on an adjustable slide base. 2,6 COMPRESSORS a8 The unit shall be a single or multiple scroll compressors type with a high ""%@ low sound power le;el@ best sound ?uality due to low discharge pulse and high reliability to meet application re?uirement. 1loor standing precision air< conditioners with capacity eBceeding '2 C. shall ha;e dual compressors with independent refrigerant circuit for maBimum load fleBibility. The hermetic motor shall be suction gas<cooled with high starting tor?ue and the windings shall be inherently protected from o;er<loading@ single phasing and under<;oltage operation. The compressor shall ha;e a checA ;al;e which located directly abo;e the fiBed scroll discharge port to pre;ent the compressor from running bacAwards after the power has been switched off. The motor shall be fitted with a thermostat which protects the compressor if a malfunction occurs. 2,7 *I)TERS a8 The filter chamber shall be an integral part of the system@ designed within the frame and cabinet. The filters shall be disposable type +9D efficient 7based on AS!%A" 2'<438 or "(- basd on "uropean standards. 2,2 E)ECTRICA) RE3EAT a8 The unit shall ha;e multi<stage stainless steel finned tubular reheat coils capable of pro;iding ample capacity to maintain room dry bulb conditions during a system call for dehumidification. The reheat shall be installed on the air discharge side of the cooling coil and shall ha;e three 7+8 stages to pro;ide more accurate controlled response to the re?uirements of the computer room. The heating elements shall be protected by thermal and air flow status safety switches. The three stages of reheat shall ha;e a noticeable lowering of energy use and to be operate on +<phase supply. 2,4 STEAM GENERATOR 3-MIDI*IER5OPTION6 a8 "ach en;ironmental control units shall pro;ide with a steam generator humidifier. The steam generating humidifier shall be of the self contained disposable type with electronic control to pro;ides humidification downstream of the cooling coil. The humidifier is designed to produce full rated steam output at an optimum low water le;el. 2,+0 CONDENSING SECTION a8 The casing of the condensing section shall be hea;y gauge steel panels@ insulated with EF thicA B # E ib per cu. 1t mat faced line<acoustic fiberglass@ tightly fitted with gasAet on rigid frame@ to guard against leaAs of conditioned air. All steel parts shall be coated with o;en<baAed epoBy paint@ which gi;es eBcellent finishing@ weatherability and salt<spray test of minimum 5-9 hours. /;en<baAed epoBy paint shall pro;ide the best painting system@ which e;en can coat the inaccessible places of part liAe the edges@ the joints or interior surface of hollow sections. b8 The condenser coils shall be of seamless copper tubes mechanically bonded to aluminum fins for heat rejection performance enhancement as well as corrosion resistance and tested under water to '599 APa with compressed air. 1ans shall be propeller type direct dri;en by weatherproof electric induction motors. 1an motor has class * insulation and splash<proof enclosure. The motor shall be suitable for operation with -#2>+>29 electric supply with G#9D or #2D ;oltage fluctuation. %e;ision 9< 0ate= Specifications 94'3 Precision air conditioning system Page +>2 Archetype Project Name Project Phase 2,++ MONITORING AND CONTRO))ING SYSTEM a) The unit shall ha;e - rows@ '9 character &,0 display wall mounted type for ceiling hung unit and 5 rows@ '' character &,0 display for floor mounted unit. t shall display data centreHs temperature@ humidity@ airflow status@ cleanliness and shall be able to pro;ide component run times@ alarm history@ an automatic self< test of the microprocessor on system start<up. The microprocessor controller shall be of #3 bits type with flash memory to stored customised application programming data. All of these messages shall be spelled out in full "nglish &anguage on the &"0 display. Multiple alarms shall be able to be displayed se?uentially in order of occurrence. b) The user<friendly menu selection switch shall permit step<by<step programming and display of the following functions= Temperature set point #5 9, to '6 9, 732 1 to 52 18 Temperature sensiti;ity 9.2 9, to '.4 9, 7# to 218 !umidity set point -9D to 39D %! !umidity sensiti;ity #D to #9D %! Temperature alarm points !umidity alarm points (nit start time delay ,urrent temperature 79, or 18 ,urrent humidity 7D%!8 ,ooling stages #@ ' as applicable !eating stages #@'@+ !umidification 0ehumidification ,urrent D of capacity and the a;erage D of capacity for the last hour of operation for compressors@ humidification@ dehumidification@ reheat and chilled water. The unit shall ha;e standard alarm system as follows= ,ompressor high pressure !igh and low temperature !igh and low humidity No air flow ,hange filter !umidifier failure Manual o;erride Power failure restart ,ompressor short cycle Temperature sensor error !umidity sensor error 1irestat tripped &ocal alarm 7programmable8 Maintenance due c) n order to facilitate maintenance and ser;ice@ component run times for fan motor@ compressor operation@ reheat stages@ humidification and dehumidification@ %e;ision 9< 0ate= Specifications 94'3 Precision air conditioning system Page ->2 Archetype Project Name Project Phase the unit shall be able to recall and display on the &,0. The historical data base shall be maintained by battery bacA<up should power fail. . E7EC-TION .,+ INSTA))ATION a) nstall e;aporator<fan components using manufacturerIs standard mounting de;ices securely fastened to building structure. b) nstall ground<mounted@ compressor<condenser components on #99<mm thicA@ reinforced concrete baseJ #99 mm larger on each side than unit. c) nstall ground<mounted@ compressor<condenser components on polyethylene mounting base. d) nstall roof<mounted@ compressor<condenser components on e?uipment supports specified in related Sections. e) nstall compressor<condenser components on restrained@ spring isolators with a minimum static deflection of '2 mm. %efer to related Section. .,2 CONNECTIONS a8 ,onnect precharged refrigerant tubing to componentIs ?uicA<connect fittings. nstall tubing to allow access to unit. b8 ,onnect supply and return water coil with shutoff<duty ;al;e and union or flange on the supply connection and with throttling<duty ;al;e and union or flange on the return connection. c8 ,onnect supply and return condenser connections with shutoff<duty ;al;e and union or flange on the supply connection and with throttling<duty ;al;e and union or flange on the return connection. d8 nstall piping adjacent to unit to allow ser;ice and maintenance. .,. *IE)D /-A)ITY CONTRO) a) %etain first paragraph below to re?uire a factory<authoriKed ser;ice representati;e to perform@ or assist ,ontractor with@ field inspections@ tests@ and adjustment. %etain one of two options to suit ProjectJ delete both to re?uire only an inspection before field testing. b) ManufacturerIs 1ield Ser;ice= "ngage a factory<authoriKed ser;ice representati;e to inspect@ test@ and adjust field<assembled components and e?uipment installation@ including connections. %eport results in writing. c) &eaA Test= After installation@ charge system and test for leaAs. %epair leaAs and retest until no leaAs eBist. d) /perational Test= After electrical circuitry has been energiKed@ start units to confirm proper motor rotation and unit operation. %emo;e malfunctioning units@ replace with new components@ and retest. e) Test and adjust controls and safeties. %eplace damaged and malfunctioning controls and e?uipment. 0 SC3ED-)E "N0 /1 S",T/N %e;ision 9< 0ate= Specifications 94'3 Precision air conditioning system Page 2>2