Escolar Documentos
Profissional Documentos
Cultura Documentos
INTERFACE
Data sheet
103161_en_01
1
Description
The MACX MCR-SL-CAC-5-I(-UP) current transducer converts sinusoidal alternating currents 1 A or 5 A into standard
analog signals 0...20 mA or 4...20 mA. The DIP switches accessible on the topside of the housing enable configuration of
the input and output current. The MACX MCR-SL-CAC-5-I
current transducer provides a voltage supply range of 19.2 V
DC to 30 V DC.
Features
Table of contents
Description .............................................................................................................................. 1
Installation ............................................................................................................................... 7
6.1
Connection notes ................................................................................................................ 7
6.2
Structure ........................................................................................................................... 7
6.3
Block diagram ..................................................................................................................... 7
6.4
Power supply ...................................................................................................................... 7
6.5
Assembly........................................................................................................................... 8
6.6
Connecting the wires ............................................................................................................ 8
Configuration ........................................................................................................................... 9
103161_en_01
PHOENIX CONTACT
Ordering data
Description
Type
Order No.
Pcs. / Pkt.
Current measuring transducer for 1 A and 5 A AC, the output signal 0...20
mA or 4...20 mA, can be configured using a DIP switch with an operating
mode indication through an LED
2810612
Current measuring transducer for 1 A and 5 A AC, the output signal 0...20
mA or 4...20 mA, can be configured using a DIP switch with an operating
mode indication through an LED
2810625
Accessories
Type
Order No.
Pcs. / Pkt.
DIN rail power supply unit, primary-switched mode, slim design, output: 24
V DC / 1.5 A
MINI-SYS-PS-100-240AC/24DC/1.5
2866983
DIN rail power supply unit, primary-switched mode, slim design, output: 24
V DC / 1.5 A, ATEX approval
MINI-PS-100-240AC/24DC/1.5/EX
2866653
DIN rail connector for current transducers, gold-plated contacts, for DIN rail
mounting, 5-pos.
2707437
50
DIN rail connector for DIN rail power supply unit, gold-plated contacts, for
DIN rail mounting, 5-pos.
2709561
10
Technical data
Configurable/programmable
0 A AC ... 1 A AC (configurable)
0 A AC ... 5 A AC (configurable)
Overload capacity
2 x IN (continuous)
Surge strength
20 x IN (1 s)
Nominal frequency fN
50 Hz
45 Hz ... 65 Hz
Curve type
Sine
Operate threshold
0.3 % (1 A)
0.45 % (5 A)
Signal input
Voltage input signal
300 V AC
0 A AC ... 0.001 A AC
0 A AC ... 0.005 A AC
Input impedance
< 50 m
Output
Output description
Current output
Non-load voltage
15 V
0 mA ... 20 mA (configurable)
4 mA ... 20 mA (configurable)
25 mA
Configurable/programmable
Ripple
Status display
103161_en_01
PHOENIX CONTACT
Supply
24 V DC (-20%...+25%)
19.2 V DC ... 30 V DC
< 32 mA
(at UB=24 V DC, IOUT=20 mA)
< 30 mA
(at UB=24 V DC, IOUT=20 mA)
< 13 mA
(at UB=230 V AC, IOUT=20 mA)
Power consumption
< 0.9 W
(at UB=24 V DC, IOUT=20 mA)
< 0.9 W
(at UB=24 V DC, IOUT=20 mA)
< 3.4 W (at UB= 230 V AC, IOUT=20 mA)
Yes
Yes
General data
Measuring principle
Additional error
max. 300 ms
Typ. 200 ms
Yes
Mounting position
Any
Degree of protection
IP20
Pollution degree
Dimensions W / H / D
Type of housing
Connection data
Connection method
Screw connection
24 ... 14
Stripping length
8 mm
Safe isolation
Safe isolation
acc. to EN 61010
acc. to EN 61010
II
III
Pollution degree
Ambient conditions
Ambient temperature (operation)
Altitude
2000 m
103161_en_01
PHOENIX CONTACT
Conformance / approvals
Conformance
CE-compliant
ATEX
II 3 G Ex nA II T4 X
UL 508 Recognized
103161_en_01
PHOENIX CONTACT
5
5.1
5.2
Installation notes
where applicable).
It is not permissible to open or modify the device. Do not
repair the device yourself but replace it with an equivalent
device. Repairs may only be carried out by the manufacturer. The manufacturer is not liable for damage resulting
from violation.
The IP20 degree of protection (EN 60529) of the device
is intended for use in a clean and dry environment. Do not
subject the device to any load that exceeds the described
limits.
The device is not designed for use in atmospheres with a
danger of dust explosions.
The housing of the device provides a basic insulation
against the neighboring devices, for 300 V eff. If several
devices are installed next to each other, this has to be
taken into account, and additional insulation has to be installed if necessary. If the neighboring device is equipped
with basic insulation, no additional insulation is necessary.
Provide overcurrent protection (I 16 A) within the installation.
103161_en_01
PHOENIX CONTACT
Installation
6.1
Connection notes
Block diagram
L(+)
OUT
1.1
L(+) 1.2
3.1
OUT1
N(-)
1.3
3.2
GND
N(-)
1.4
3.3
GND
3.4
GND
4.1
1A
4.2
5A
4.3
NC
4.4
IN
6.2
Structure
Figure 2
2
6.4
Block diagram
Power supply
1A
5A
3
1
ATTENTION:
N
O
F
O
-C
L
C
-U
-I
-5
A
L(
+
L(
IG
(-
(-
Structure
DIP switch
LEDs: diagnostics
Transparent cover
Output: Standard signals
Supply voltage
Input
Connection option for DIN rail connector
103161_en_01
PHOENIX CONTACT
Assembly
Figure 4
Figure 3
6.6
103161_en_01
PHOENIX CONTACT
Configuration
Application example
DIP
N
O
F
O
1A
5A
0...20mA
S
-C
R
R
E
L
C
-I
-5
A
-U
5A
+
L(
+
L(
IG
)
(-
)
(-
24V
00
10
Figure 5
Figure 6
Mains voltage
Current measurement
DIP switches
OFF = 1 A
ON = 5 A
OFF = 0 mA ... 20 mA
ON = 4 mA ... 20 mA
103161_en_01
PHOENIX CONTACT GmbH & Co. KG 32823 Blomberg Germany Phone: +49-(0) 5235-3-00
PHOENIX CONTACT P.O.Box 4100 Harrisburg PA 17111-0100 USA Phone: +717-944-1300
www.phoenixcontact.com