Escolar Documentos
Profissional Documentos
Cultura Documentos
Step 2 If the version is V100R002C02SPC100, check that the system does not load other files.
<S2300> display patch-information
Info: No patch exists
Step 3 If the system loads other files (patches earlier than V100R002C02SPH005), delete the
files.
<S2300> patch delete
Patch will be deleted! Confirm?[Y/N]:Y
Info: Patch delete successfully on master board.
----End
1----------
Start the FTP server on the S3300, and set the FTP user name to ftpuser and password to ftpwd.
<Quidway> system-view
[Quidway] ftp server enable
[Quidway] aaa
[Quidway-aaa] local-user ftpuser password simple ftppwd
[Quidway-aaa] local-user ftpuser service-type ftp
[Quidway-aaa] local-user ftpuser ftp-directory flash:/
[Quidway-aaa] return
Run the ftp ip-address command on the PC to set up an FTP connection with the S3300 and
enter the FTP client view.
D:\>ftp 1.1.1.1
Connected to 1.1.1.1.
220 FTP service ready.
User (1.1.1.2:(none)): ftpuser
331 Password required for 1.
Password:
230 User logged in.
ftp>
Run the put source-filename [ destination-filename ] command on the FTP client (PC) to upload
the VRP from the PC. After uploading the VRP, run the bye command to close the FTP
connection and return to the user view.
ftp> put "D:\ V100R002C00SPC301.cc"
200 Port command okay.
150 Opening ASCII mode data connection for V100R002C00SPC301.cc.
226 Transfer complete.
ftp: 4940436 bytes sent in 35.10Seconds 140.76Kbytes/sec.
ftp> bye
221 Server closing.
D:\>
Step 14 Specify the VRP in service, which is loaded when the S3300 is started.
<Quidway> startup system-software S2352_S3352-V100R003C00SPC301.cc
If the preceding information is displayed after you run the startup system-software file command,
enter Y to update the BootROM. If the BootROM is updated successfully, go to Step 15; otherwise,
go to Step 14.
Warning: Basic BOOTROM will be upgraded. Continue?(Y/N)[N]: y
BOOTROM begin to be upgraded ! please wait for a moment
Info: BOOTROM UPGRADE OK
The new version is 116. Please restart to validate the upgrade.
Step 15 Upgrade the BootROM in service, which is loaded when the S3300 is started.
<Quidway> system-view
[Quidway] upgrade basic-bootrom S2352_S3352-V100R003C00SPC301.cc
Confirm basic BOOTROM will be upgrade?(Y/N)[N]: y
BOOTROM begin to upgraded ! please wait for a minute...
BOOTROM UPGRADE OK
The new version is 116. Please restart to validate the upgrade.
----End
Step 18 Check that the system does not load other files.
<S5328> display patch-information
Info: No patch exists on unit 0
Step 19 If the system loads the V100R003C00SPH001 file, run the following command:
<S5328> patch delete
Patch will be deleted! Confirm?[Y/N]:Y
Info: Patch is deleting on unit 0...
Info: Patch delete successfully on master board.
The SPs later than V100R003C00SPH001 are cumulative patches and these patches do not need to
be deleted.
----End
Step 20 Download the patch S23_33_53-V100R003SPH006.pat to the flash memory of the device.
Download the patches to the flash memory of the device in FTP mode or through a serial
interface.
---End
0----------
As shown in the preceding command output, there are 37 patches in the RUN state on the S5328.
The number of patches must be the same as the number of patches described in Error! Reference
source not found..
NOTE: If you see this during the reboot process please go to the Problem during Upgrade
process section in next page to solve it.
And if after the upgrade you cant use the VRRP feature:
<HN-HJSW-1>sys
Enter system view, return user view with Ctrl+Z.
[HN-HJSW-1]int vlan 30
[HN-HJSW-1-Vlanif30]vrrp ?
Error:Unrecognized command found at '^' position.
Do as follows:
<Quidway>sys
[Quidway]_h
Password: Vrp&8031
[Quidway-hidecmd]shell
[Quidway-hidecmd]->
->
-> Shell_flashUnlockSector 4
-> Shell_flashUnlockSector 5
-> Shell_flashUnlockSector 6
-> Shell_flashUnlockSector 7
-> Shell_flashEraseSector 4
-> Shell_flashEraseSector 5
-> Shell_flashEraseSector 6
-> Shell_flashEraseSector 7
-> exit
[Quidway[Quidway-hidecmd]return
<Quidway> reboot
Info: The system is now comparing the configuration, please wait.
Info: Save current configuration?[Y/N]:
y or n
System will reboot! Continue?[Y/N]:
y
************************************************
: 32KB
Memory Size
: 128MB
BOOTROM MENU
1. Boot with default mode
2. Enter serial submenu
3. Enter startup submenu
4. Display flash files
5. Modify BOOTROM password
6. Reboot
Enter your choice(1-6): 6
Reboot...
End