Escolar Documentos
Profissional Documentos
Cultura Documentos
CALCIUM
SILICATE PIPE
PIPE &
& BLOCK
BLOCK INSULATION
INSULATION
CALCIUM SILICATE
Description
HI-THERM calcium silicate block and pipe high temperature
insulation is manufactured using an industry preferred filter
press method which provides accurate dimensional tolerances and superior compressive and flexural strength.
These attributes facilitate installation and provide exceptional resistance to mechanical abuse. HI-THERM calcium silicate insulation is asbestos free and meets or exceeds all of
the requirements of ASTM C 533, Type I.
PHYSICAL PROPERTIES
Compressive Strength
(ASTM C 165)
HI-THERM, nominal
177 psi. to Produce 5%
compression (1206 kPa)
A.S.T.M.
Min. 100 psi.
(688 kPa)
Max 15.0
(240 kg/m3)
Flexural Strength
(ASTM C 203)
70 psi.
(483 kPa)
Min. 50 psi.
(344 kPa)
Applications
HI-THERM calcium silicate insulation is recommended for
use on equipment and piping operating at temperatures
from ambient to 250 Deg F (121 Deg C) indoors and protected outdoors up to 1200 Deg F (649 Deg C). it is ideally
suited for industrial use in areas such as the petrochemical
and power generating industries where energy conservation,
process control, personal protection and fire protection are
prerequisites.
Tumbling Friability
(ASTM C 421)
Max. 20%
Max. 40%
Linear Shrinkage
(ASTM C 356)
Max. 2%
Surface Burning
Characteristics
(ASTM E 84)
Flame Spread-0
Smoke developed-0
Max. 0
Max. 0
1200 Deg F.
(649 Deg C.)
Forms available
HI-THERM calcium silicate block and pipe insulation are
available
Product Range
Calcium Silicate Pipe Cover
Length:
3 feet (915mm)
Diameter:
half-37 inches (22-942mm)
half-19 inches 2 pcs/section
20-28 inches 4 pcs/section
29-37 inches 6 pcs/section
Thickness:
1-3 inches (25-76mm) in single layer in half inch (13mm)
increments. Over 3 inches (76mm) are layed
Calcium Silicate Board
Length:
3 feet (915mm)
Width:
6 inch/12inch (150/305mm)
Thickness:
1-3 inches (25-75mm)
Other Type available
Service Temperature: 1200 Deg F (650 Deg C)
Service Temperature: 2012 Deg F (1100 Deg C)
Density: 10-11 Ib/cu.ft. (170kg/m3)
Density: 8-9Ib/cu.ft. (130-150kg/m3)
Length: 2 feet (600 / 610mm) 3 feet (915mm) on request
Board Width: 6 inch / 12 inch (150 / 300mm)
Groove & Curved Board with 2 bevelled edges
Other sizes available upon request
SPECIFICATION COMPLIANCE
ASTM C 533, TYPE I
ASTM C 795
Tested by TUTCO SCIENTIFIC CO., USA
(Test Report Copies on request)
THERMAL CONDUCTIVITY ("K")*
Mean
K
Mean
Temp
Btu-in.
Temp
Deg. F
/h-ft2-Deg F
Deg. C
200
.390
93
300
.418
149
400
.458
204
500
.512
260
600
.579
316
700
.659
371
K
W/M
Deg. C
.0562
.0603
.0660
.0738
.0835
.0950
DISCLAIMER
Ultimet Group
01634 232666
Email: industrial@ultimetgroup.com
01634
232666
Website:
www.ultimetgroup.com
Email: enquiries@ultimetalloys.com
Website: www.ultimetalloys.com
These data sheets are based on specifications, data and test results at time of
DISCLAIMER
publication.
No guarantee as to completeness, accuracy or results is either expressed
orThese
implied.
Thesheets
suitability
an intended
use is the responsibility
the user.
choice
data
are for
based
on specifications,
data and testofresults
at As
time
publication.
Noofguarantee
to completeness,
accuracy
ofofmaterial,
method
applicationasand
site conditions are
beyond or
ourresults
controlisweeither
accept
implied.
The suitability
for an intended
useproved
is the to
responsibility
noexpressed
liability foror
direct
or consequential
damages.
Any material
be defective
of thethe
user.
As choice
material,
method
of application
and site conditions are
within
published
shelfoflife,
from date
of supply,
will be replaced.
beyond our control we accept no liability for direct or consequential damages.
Any material proved to be defective within the published shelf life, from UIS011
date
of supply, will be replaced.