Escolar Documentos
Profissional Documentos
Cultura Documentos
POWER
Product
Product/technology
No.
P-1
MHI 1000MW high temperature
ultra-supercritical pressure
coal-fired power plant
P-2
Hitachi Supercritical/ultra
supercritical pressure coal-fired
power plant
P-3
MHI Large capacity high
temperature ultra-supercritical
steam turbine
P-4
MHI 1000MW high temperature
ultra-supercritical pressure
coal-fired boiler
P-5
IHI Large capacity high temperature
ultra-supercritical boiler
P-6
IHI Pressurized fluidized bed boiler
combined cycle Plant
P-7
Integrated coal gasification
combined cycle
P-8
Integrated coal gasification fuel cell
combined cycle
P-9
MHI RS pulvelizer
P-10
P-11
Function
Generation
Product group
Product feature
Ditto
Ditto
Steam turbine
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
IGFC
Ditto
Coal-fired boiler
auxiliary
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
Ditto
Gas-fired plant
Pulvelizer with
stationary/rotary
separator
Low NOx coal burner
Axial flow fan for FDF,
IDF, PAF
Selective catalytic
DeNOx equipment
GTCC
Ditto
Ditto
Gas/oil- fired
plant
Ditto
Ditto
Ditto
Ditto
Gas-fired plant
Ditto
Oil-fired plant
Ditto
Gas-fired plant
Ditto
Gas, oil,
(power & heat) coal-fired
P-21
Ditto
P-22
Ditto
Ditto
Hydraulic
turbine plant
Ditto
Ditto
Ditto
Ocean thermal
power plant
Geothermal
P-12
P-13
P-14
P-15
P-16
P-17
P-18
P-19
P-20
P-23
P-24
P-25
P-26
P-27
Abbreviation of manufacturersname
Ditto
Transmission
Distribution
Wind turbine
plant
Solar cell
Transformer
Geothermal reservoir
analysis tool
Amorphous metal
transformer
MES:Mitsui Engineering & Ship Building Co.,Ltd., WEC:West Japan Engineering Consultants,Inc. Xenesys: Xenesys Inc.
11
P-1 MHI 1,000MW High Temperature Ultra-Supercritical Pressure Coal-fired Power Plant
Power
Generation
1,000 MW
Steam condition
(at turbine inlet)
Pressure
main steam
Temperature Main steam
Reheat steam
Main fuel
Pressure mode
24.5 MPa
600 C
600 C
Imported coal
Sliding pressure
Type of boiler
Steam flow
Steam
pressure
Steam
temperature
Feedwater
temperature
Fuel
Combustion
Pulvelized coal
system
Draft system
Primary air
system
Type of steam
turbine
Steam condition
Main steam
Pressure
Temperature
Main steam
Reheat steam
Rotating speed
Primary turbine
Secondary
turbine
Last blade length
No. of FW heater
stages
11
600 C
600 C
3,600 rpm
1,800 rpm
46 ins
8
Features
High efficiency over whole operating load range
Large capacity for better operating performance and cost performance
High operational flexibility for a wide range of operating condition
Excellent environmental performance
Excellent dynamic performance
High reliability
Energy Saving /CO2 Emission Reduction
Fuel consumption is less by about 5(8)% compared with the standard units with steam condition
of 16.7MPa538/538C in India depending on unit capacity and design
CO2 emission is less by about 5 (8)% than the standard units with steam condition of
16.7MPa538/538C
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
E-mail
12
P-2 Hitachi Supercritical / Ultra Supercritical Pressure Coal-fired Thermal Power Plant
Power
Generation
Outline of Product/Technology
(1) Function
Power Generation
(2) Structure/System
Apply supercritical pressure steam to realize high efficiency in power generation
We can provide the most efficient generating component for coal-fired thermal power plant.
(3) Features
-
13
Generation
Steam turbine
Outline of Product/Technology
(1) Function
High efficient power generation with high temperature supercritical pressure steam
Large power production
Excellent load swing capability
High reliability
(2) Structure/System
(3) Features
High efficiency
Large output
Flexible operation
Excellent dynamic performance
High reliability
(3) Contact to
Tel
14
Generation
Coal-fired boiler
(3)Technical Features
High efficiency
High flexibility for operating condition and excellent dynamic performance
Environmentally friendly performance
High reliability with simple robust construction
Less feedwater pressure loss with vertical furnace wall with rifled tubes
Energy Saving /CO2 Emission Reduction
More than 5%(8%) reduction of fuel consumption and CO2 emission is achievable compared with
the standard unit with steam condition of 16.7MPa538C /538C.
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
15
16
P- 5 IHI
Power
Generation
Boiler
Rated output
: 1,000 MW
Steam condition at turbine inlet
Main steam press. : 24.5 MPa
temp. : 600 C
RH steam temp.
: 600 C
Maximum continuous evaporation of
boiler : 2900 t/h
Main fuel: Wide range of imported coal
Commercial operation date: June 1998
EPDC Tachibanawan PS No.1 boiler
(3) Features
(1) Helically wound tube circuitry is used in the lower furnace to meet variable pressure operation.
(2) Boiler water circulation system is applied to keep a minimum water flow through the furnace during
start-up
(3) Others
Energy Saving /CO2 Emission Reduction
Fuel consumption and CO2 emission are much less compared with the standard steam condition of
16.7MPa538/538C in India in case that it is coupled with a proper steam turbine plant.
Information of Manufacturer
(1) Name of Company and DepartmentIshikawajima-harima Heavy Industries Co., Ltd.
(2) Address
(3) Contact to
Tel
E-mail
17
18
P- 6
Power
Generation
PFBC
: 360 MW
: 290 MW
: 24.12 MPa
temp.
: 566 C
RH steam temp.
: 593 C
boiler
: 760 t/h
: 75 MW
GT inlet pressure
: 1.55 MPa
GT inlet temperature
: 870 C
Main fuel
: Imported coal
DeSOx
DeNOx
(3) Features
High plant efficiency
Low emission
In-Bed DeSOx
Less NOx
Less CO2
Compactness
Energy Saving /CO2 Emission Reduction
Less fuel consumption and CO2 emission
Information of Manufacturer
(1) Name of Company and DepartmentIshikawajima-harima Heavy Industries Co., Ltd.
(2) Address
(3) Contact to
Tel
E-mail
19
110
P-7
Power
Generation
Outline of Product / Technology
IGCC
(1) Function
Coal gasification and power generation
High efficiency power generation with coal
Environmentally friendly coal-used power generation
(2) Structure/System
Coal gasifier
Coal gas
Coal feed
system
Wet
DeSOx
Porous
filter
Gypsum
Combust
Air
Stack
Char
N2
O2
Air
Air
(3) Contact to
Tel
111
P-8
Generation
IGFC
(3) Features
Ultra high efficiency power generation with coal which is the most abundantly reserved fuel on the earth.
Ultra high efficiency such as 60% (HHV basis) or higher is obtainable with coal. (under development)
Environmentally friendly power generation with coal
As the plant efficiency is much higher than those of the presently available power generation
technologies, CO2 emission is reduced to about two-third (2/3) contributing to the prevention of global
warming.
As the fuel gas is cleaned, then used for fuel cell first, then burnt in combustor for gas turbine, the exhaust
gas contains almost no SOx, particulate and negligible amount of NOx, CO and hydrocarbon.
Versatility in application
As the main power generation element is fuel cell which is static power generator by electro-chemical
reaction, moving power generators such as gas turbine and steam turbine are comparatively smaller, the
operation of the plant is low in noise and vibration and much less cooling water is required.
Therefore it is applicable not only to central power generation but to cogeneration plant deployed near
urban area.
The plant is suitable for central power generation of large capacity and medium to small capacity as well.
The type of fuel cell shall be SOFC (Solid Oxide Fuel Cell) which is suitable for high temperature
operation such as 1000C.
(3) Contact to
Tel
E-mail
Fax
112
P-9
Power
MHI RS Pulvelizer
Generation
Boiler auxiliary
(3) Features
High uniform fineness
Effective classification of coarse
particle
High combustion efficiency
Low NOx emission and little
unburnt carbon
High capacity and minimum
power
consumption
Energy Saving /CO2 Emission Reduction
High boiler efficiency is obtained owing to minimum unburned carbon loss with low excess air
combustion, which results in reduction of fuel consumption and CO2 emission.
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
113
P-10
Power
Boiler auxiliary
Advanced PM burner
(3) Features
Stable ignition and combustion owing to dense fuel combustion flame with a wide range coal
Stable, uniform, complete combustion owing to long helical trajectory of combustion flame
High combustion efficiency with mini9mum excess air and unburnt carbon
Low NOx emission
Energy Saving /CO2 Emission Reduction
High boiler efficiency is obtained owing to the least unburned carbon loss with minimum excess air,
which results in reduction of fuel consumption and CO2 emission.
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
114
P-11
Power
Boiler auxiliary
(3) Features
High efficiency over wide load range resulting in little power consumption
Easy operation with automatic control and easy maintenance
Abundant experience of application to modern boiler plants showing its excellent performance and
reliability
For high pressure requirement, double stage axial fan is available
Energy Saving /CO2 Emission Reduction
Least power consumption of draught system over whole load range owing to the high efficiency of
Mitsubishi blade pitch control axial flow fan
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
115
P-12
Power
(3) Contact to
Tel
116
P-13
Power
Generation
Outline of Product / Technology
GT CC
(1) Function
Highest efficiency natural gas-fired power generation technology commercially available at the
present.
Most environmentally friendly power generation using fossil fuel commercially available at the
present.
Suitable for large output. Maximum output of a single shaft type CC (gas turbine combined cycle
plant composed of a gas turbine with a steam turbine on one shaft) is almost 500MW.
(2) Structure / System
HRSG
HP/IP ST
Stack
Generator
LP steam turbine
Gas turbine
(3) Contact to
Tel
As for MHI G series gas turbine, reference shall be made to the attached catalogue.
117
118
P-14
Power
Combined cycle
(1) Function
Barge mounted combined cycle power generation plant
Construction work at site is minimized
(2) Structure / System
Information of Manufacturer
(1) Name of Company and DepartmentIshikawajima-Harima Heavy Industries Co., Ltd.
(2) Address
(3) Contact to
Tel
Fax
ULR
119
120
P-15
Power
Generation
Gas turbine
Information of Manufacturer
(1) Name of Company and DepartmentIshikawajima-Harima Heavy Industries Co., Ltd.
(2) Address
(3) Contact to
Tel
121
122
123
P-16
Power
Gas turbine
Outline of Product/Technology
(1) Function
Power Generation
(3) Features
- High Reliability and Easy Maintenance with Heavy Duty Design
- High Fuel Flexibility (Natural Gas, Diesel Oil, Off gas, etc.) with Low Emission Level
- Applicable to Replacing Existing Old MS5001Gas Turbine with New H-25
Energy Saving / CO2 Emission Reduction
(1)Technical Features
Fuel saving and low emission level are achieved by using the H-25.
- Efficiency 34.8% (LHV, ISO base load condition, with Natural Gas)
- Low NOx Emission (25 ppm@15%O2, ISO base load operation, (Low NOx combustor case)
(2) Energy Saving / CO2 Emission Reduction
- In case of replacement from 15 years old gas turbine to new H-25, fuel consumption will be
reduced to around 3/5.
(Depends on existing equipment specification, site condition (temperature, humidity, etc.) and
fuel specification.)
Information of Manufacturer
(1) Name of Company and DepartmentHitachi, Ltd. / Power Systems
(2) Address
Akihabara Daibiru Building, 18-13, Soto-Kanda 1-chome, Chiyoda-ku,
Tokyo, 101-8608 Japan
(3) Contact to
Mr. Keika Gomi
Tel
81-3-5295-5787,
Fax81-3-4564-3511
E-mail
keika.gomi.qz@hitachi.com
124
125
126
P-17
Power
Generation
Outline of Product / Technology
SOFC
(1) Function
Ultimate power generation technology for high efficiency over 65
Most environmentally friendly power generation technology owing to almost no emission of SOx,
NOx, particulate and least emission of CO2. SOFC is an electro chemical apparatus without moving
parts unlike combustion engines and without producing noise and vibration.
Suitable not only for central power generation but for distributed power generation and cogeneration
which can be deployed anywhere gaseous fuel is available.
(2) Structure / System
Inverter
Fuel
Combustor
Condenser.
Exhaust
gas
Most suitable for cogeneration of power and steam owing to the relatively high operating
temperature of SOFC, suitable for the deployment even at populated area where demand for
steam / hot water exists.
Energy Saving / CO2 Emission Reduction
The power generation efficiency is so high as 65 to 75% that fuel consumption is greatly reduced,
resulting in the large reduction of CO2 emission correspondingly.
If compared with conventional coal-fired plant, CO2 emission is less than 40%.
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
127
Oil-fired
Diesel engine
Outline of Product/Technology
(1) Function
2-stroke low speed diesel engine power plant
(2) Structure/System
Generating set driven by low speed diesel engine, which is widely applied to propulsion for
ocean-going vessel due to very high reliability.
(3) Features
High thermal efficiency (4850% on LHV base)
Higher Availability (More than 90%)
Low maintenance cost
Less consumption of spare parts
Information of Manufacturer
(1) Name of Company and DepartmentMitsui Engineering & Shipbuilding Co., Ltd.
Power System Sales Dept.
(2) Address
(3) Contact to
Tel
E-mail
128
P-19
Power Generation
Gas engine
(1) Function
Power generation with gas fuel
Micro-pilot, instead of spark-ignited, combustion system to challenge the performance level of
Diesel engines and gas turbines
(2) Structure / System
(3) Features
Higher electrical efficiency
5,800kWe, 47.6% on LHV base
1,070kWe, 41.6 to 5,255kWe, 43.7% on LHV base
Applicable to low calorie (5,020kJ/Nm3) gas fuel
Low NOx lean-burn system
Energy Saving / CO2 Emission Reduction
(1) Energy saving
Fuel consumption is reduced owing to the high efficiency.
(2) CO2 Emission Reduction
CO2 emission is reduced owing to the reduction of fuel consumption
Information of Manufacturer
(1) Name of Company and DepartmentNiigata Power Systems Co., Ltd.
(2) Address
(3) Contact to
Tel
Fax
E-mail
129
130
131
P- 20
Power
(1) Function
Cogeneration (combined heat and power generation or CHP) is to produce heat (steam and/or hot
water) using the energy of exhaust gas and/or low temperature stream in addition to power generation.
As for the engine, diesel engine, gas engine, gas turbine, gas turbine combined cycle, steam turbine
plant and fuel cell are used depending on available fuel, steam/hot water condition required, capacity
and so on.
Compared with power plant of which energy efficiency is maximum about 50%, much higher efficiency
upto 80 to 90% is obtainable.
The heat (steam/hot water) is used for refrigerating system, factory use, swimming pool, bath, home
use.
(2) Structure/System
The following cogeneration system is an example using gas engine. By installing HRSG (heat recovery
steam generator to produce steam with waste heat of exhaust gas and heat exchangers to produce
hot/warm water with the heat of cooling water, energy efficiency is increased from 43.5% to 72.5% while
maintaining power generation efficiency of 43.5%.
Exhaust gas
HRSG
Feedwater
Air cooler
Fuel
100%
Steam
Power
Engine
Cooling water
Generator
Lub.oil
Hot water
1ry cooler
Warm water
Oil
cooler
(3) Features
High energy efficiency while keeping high power generation efficiency.
Various kinds of engines are applicable as the main engine.
High energy efficiency results in reduced fuel consumption and CO2 emission.
Energy Saving/ CO2 Emission Reduction
Fuel consumption is much reduced to maximum about 50% by cogeneration from exclusive power
and independent heat generation (Example: Power generation efficiency of g40% is possible to
be raisedc80% of cogeneration efficiency)
CO2 emission is reduced at the rate of g /c
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
132
P-21
Power
Generation
Outline of Product / Technology
Wind turbine
(1) Function
Clean power generation with wind (renewable clean energy) with no fuel consumption and no CO2
emission
Suitable for distributed power generation deployed where wind is available.
(2) Structure / System
(3) Contact to
Tel
133
134
135
P-22
Power
Generation
Outline of Product / Technology
Photovoltaic cell
(1) Function
Clean power generation with sunlight (renewable clean energy) with no fuel consumption and no
CO2 emission
Suitable for distributed power generation which can be deployed anywhere sun shines.
(2) Structure / System
(3) Features
It is amorphous Si-microcrystalline Si tandem type thin film photovoltaic cell.
It is advantageous at hot/warm region because that it produces more power than crystalline Si and
polycrystalline Si PVC at higher temperature (>25).
It does not require high quality Si such as required for crystalline/polycrystalline Si PVC, require
much less Si and less energy for manufacturing, resulting in the most environmentally friendly PVC
developed by MHI.
Energy Saving / CO2 Emission Reduction
Photovoltaic power generation is a typical renewable energy power generation technology which does
not consume any amount of fuel for power generation.
Therefore the quantity of fossil fuel required for the same amount of power generation with thermal
power is saved with photovoltaic power generation resulting in no emission of CO2.
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
136
137
P-23
Power
Generation
Outline of Product / Technology
Hydroelectric turbine
(1) Function
Power generation with hydraulic energy (renewable clean energy)
Environmentally friendly power generation
(2) Structure / System
Efficiency dependence on GT
(3) Features
Environmentally friendly power generation
Suitable for peak load shaving and quick load following operation
Suitable for storage of surplus electric power (during night) and for discharge when required (at
daytime)
Applicable to low to very high head (over 800m)
Information of Manufacturer
(1) Name of Company and DepartmentMitsubishi Heavy Industries, Ltd.
(2) Address
(3) Contact to
Tel
138
139
P-24
Power
Toshiba
Generation
Hydroelectric plant for DPG
Outline of Product / Technology
(1) Function
Small-scale hydro-power generation system Hydro - eKIDSTM using renewable energy
(2) Structure / System
140
141
142
143
144
145
146
147
148
149
P-25
Power
Outline of Product/Technology
(1) Function
Power generation
Desalination
Heat recovery for low temperature waste heat
CO2 reduction
(2) Structure/System
DTEC is a simultaneous power generation and desalination system using the low temperature waste
heats, such as waste steam, waste gas, waste water, waste heat in the cooling system etc. Uehara
cycle system is employed for power generation unit, where mixture of ammonia and water is used for
working fluid, and flash evaporation desalination method is used for desalination unit. These units are
efficiently combined in DTEC.
(3) Features
Simultaneous power generation and desalination using waste heat
No use of additional heat energy, No use of fossil fuel
Contribution to cutting of cooling cost
Contribution to decease of burdens on environment
Information of Manufacturer
(1) Name of Company and DepartmentEngineering Department, Xenesys Inc.
(2) Address
12-16-7F, Mita 3-chome, Minato-ku, Tokyo 108-8328, Japan
(3) Contact to
Takayuki Watanabe
Tel
81-3-5765-2960 Fax81-3-5765-5625
E-mail
watanabe@xenesys.com
150
151
152
153
154
155
156
157
158
P-26
Power generation
Geothermal
Geothermal reservoir
Outline of Product/Technology
(1) Function
Evaluate geothermal reservoir potential
Forecast the future reservoir and well performances
(2) Structure/System
Computer simulation coupled three kinds of numerical simulators capable of calculating mass and
energy transport from upstream (reservoirs) to downstream (turbines) has been conducted
periodically to ensure an accurate forecast of the future reservoir and well performances, which has
contributed to a stable power plant operation and a sustainable reservoir management.
(3) Features
More accurate prediction by coupling three simulators (reservoir, well bore and pipeline flow)
Changes of wellhead pressure and mass flow rate of production well can be predicted.
Fluid transportation and interconnection pressures at pipelines can be simulated.
Energy Saving / CO2 Emission Reduction
(1) Technical Features
Geothermal energy is generally defined as heat stored within the earth. A huge energy is usually
stored in the volcanic areas, where magma exists in deep underground. The geothermal power
generation produces electricity by utilizing steam, which is rainorigin underground-water heated by
geothermal energy and stored in an underground reservoir. The hot water, simultaneously spouted
out with steam, is to be separated and to be returned into underground in order to save water
resources and to protect surrounding environment
(2) Energy Saving/CO2 Emission Reduction
The 50,000kW geothermal power generation field corresponds to the oilfield of about 500,000
barrels/year production capacity with no production decrease.
The amount of the CO2 emission from power plant is usually evaluated on the life-cycle assessment
basis, where the total CO2 emission from the period of installation/construction of the plant to the
operation period of the plant is considered. From this life-cycle evaluation view point, the amount of
CO2 emission from geothermal power is extremely low 6.3 g-C/KWh.
Information of Manufacturer
(1) Company and Department West Japan Engineering Consultants, Inc. Geothermal Department
(2) Address
Watanabe-dori 1-1-1, Chuoh-ku, Fukuoka, Japan
(3) Contact to
TOKITA, Hiroyuki
Tel
81-92-781-2835
Fax81-92-751-5044
E-mail
tokita@wjec.co.jp
159
160
161
162
163
P-27
Power
Distribution transformer
Outline of Product/Technology
(1) Function
High efficient industrial transformer
(2) Structure/ System
Amorphous metal alloy in used for reducing loss
(1) Features
High efficient industrial distribution transformer
Energy Saving / CO2 Emission Reduction
(1)Technical Features
Information of Manufacturer
(1) Name of Company and DepartmentHitachi, Ltd. / Power Systems Sales Division
(2) Address
(3) Contact to
Tel
E-mail
164
165
166