Escolar Documentos
Profissional Documentos
Cultura Documentos
Rev 10/06
WAIST
All Brands
Doubled or X2
Measured to
outside edge
DraFix Cad
1a-Waist
JaneR.
WAIST
Lay garment flat, face up with waistband edges flush so that no dipping occurs at
center.
Measure along top edge of waistband, outside edge to outside edge.
Double for total waist measurement.
QUALITY POINTS
Use ruler.
There should be no slack in the waistband.
Do not stretch waistband.
IF SPECIAL SYTLING, REFER TO MEASUREMENT SPECS
WAIST
All Brands
Doubled or X2
Measured to
outside edge
DraFix Cad
1b-Waist
JaneR.
WAIST, ALTERNATE METHOD - Due to thickness and/or styling, this alternate method may
need to be used so that the waistband will lay smoothly.
Fold garment with fly turned to left.
Measure along top edge of waistband, outside edge to outside edge.
Double for total waist measurement.
QUALITY POINTS
Use ruler.
There should be no slack in the waistband.
Do not stretch waistband.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS
WAIST-Elastic
All Brands
Relaxed Measurement
Doubled or X2
Measured to
outside edge
DraFix Cad
1c-Waist
JaneR.
waist measurement.
QUALITY POINTS
Use ruler.
Do not stretch.
ELASTIC WAIST (S-T-R-E-T-C-H-E-D) - This is a stretched measurement. Stretch to full
extension of elastic
Stretched Measurement
Doubled or X2
Measured to
outside edge
DraFix Cad
1c-Waist
JaneR.
Lay garment
flat, face up
with waistband
edges flush so
that no dipping
occurs at
center.
Stretch to full
extension of
elastic.
Measure along
QUALITY POINTS
Use ruler.
Levi Strauss & Co.2001
WAIST- Elastic
All Brands
Doubled or X2
Measured to
outside edge
DraFix Cad
1d-Waist
JaneR.
HIGH HIP
4"
4"
Doubled or X2
DraFix Cad
2a-Hip
JaneR.
HIGH HIP
Lay garment flat, face up, let pant lay naturally from waist. (Back will sit higher
than front.)
Measure from bottom waistband seam, down 4 along outseam. (Or as indicated in
Measurement Specification).
Measure straight across, outside edge to outside edge.
Double for total high hip measurement.
QUALITY POINTS
Use measurement tape
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Levi Strauss & Co.2001
LOW HIP
8"
8"
Doubled or X2
DraFix Cad
2b-Seat
JaneR.
LOW HIP
Lay garment flat, face up, let garment fall naturally from waist. (Back will sit
higher than front.)
Measure from bottom waistband seam down 8 along outseam edge. (Or as
indicated in Measurement Specification).
Measure straight across, outside edge to outside edge.
Double for total low hip measurement.
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
Do not stretch garment.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Levi Strauss & Co.2001
7-1/2"
7-1/2"
DO NOT STRETCH
Doubled or X2
Smooth Out
Smooth Out
4"
DraFix Cad
2c-Seat
JaneR.
SEAT
Felled Seam
Crotch point
is equal to center
of diamond
Doubled or X2
DraFix Cad
3a-Seat
JaneR.
4"
Crotch point
is equal to
seam edge
SEAT
Lay garment flat, face up. Let garment fall naturally from waist. (Back will sit
higher than front.)
Measure up 4 from crotch point on front.
Measure straight across, from outside edge to outside edge.
Double for total seat measurement.
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
Do not stretch garment.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS
SEAT
Felled Seam
Crotch point
is equal to center
of diamond
Doubled or X2
3"
SEAT
DraFix Cad
3b-Seat
JaneR.
Crotch point
is equal to
seam edge
Lay garment flat, face up, let garment fall naturally from waist. (Back will sit
higher than front.)
Measure up 3 from crotch point on front (Or as indicated in Measurement
Specification).
Measure straight across, from outside edge to outside edge.
Double for total seat measurement.
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
Do not stretch garment.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Levi Strauss & Co.2001
SEAT-Pleated Pant
DO NOT STRETCH
Doubled or X2
Smooth Out
Smooth Out
3"
DraFix Cad
3d-Seat
JaneR.
SEAT-PLEATED PANT
Lay garment flat, face up, let garment fall naturally from waist. (Back will sit
higher than front.)
Measure up 3 from crotch point on front.
Measure straight across, outside edge to outside edge.
Double for total seat measurement.
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with open pleats and no wrinkles on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
SEAT-Pleated Pant
SEAT-PLEATED PANT
Unbutton and unzip pants.
Lay garment flat, face up, let garment fall naturally from waist. (Back will sit
higher than front.)
Using the bartack at the bottom of the J-stitch as the measuring point, measure
straight across, outside edge to outside edge.
Double for total seat measurement.
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with open pleats and no wrinkles on underside.
Do not stretch garment.
THIGH
Felled Seam
Crotch point
is equal to center
of diamond
2"
Crotch point
is equal to
seam edge
Doubled or X2
DraFix Cad
4a-Thigh
JaneR.
THIGH
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
Do not stretch garment.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS
THIGH
Felled Seam
Crotch point
is equal to center
of diamond
1"
Doubled or X2
Crotch point
is equal to
seam edge
DraFix Cad
4b-Thigh
JaneR.
THIGH
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
Do not stretch garment.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
KNEE
Crotch
Point
led
ub
Do
2"
X2
or
DraFix Cad
5a-Knee
JaneR.
KNEE
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
KNEE
Crotch
Point
led
ub
Do
X2
or "
1
DraFix Cad
5b-Knee
JaneR.
KNEE
KNEE
"
11
DraFix Cad
5c-Knee
JaneR.
Crotch
Point
led
ub
Do
X2
or
KNEE
QUALITY POINTS
Use tape measure.
Garment must lay smooth and flat with no hidden wrinkles or pleats on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Levi Strauss & Co.2001
LEG OPENING
All Brands
Sideseam Rolled In
Measure from
outside edge
to outside edge
DraFix Cad
6a-legop
JaneR.
Doubled or X2
BOTTOM
QUALITY POINTS
Use tape measure.
Smooth out, do not stretch.
If center creased, open up to measure.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Relaxed Measurement
Doubled or X2
All Brands
DraFix Cad
6b-legop
JaneR.
Sideseam Rolled In
Stretched Measurement
Doubled or X2
DraFix Cad
6b-legop
JaneR.
Measure from
outside edge
to outside edge
INSEAM
All Brands
Felled Seam
DraFix Cad
7a-Inseam
JaneR.
Crotch point
is equal to center
of diamond
INSEAM
Crotch point
is equal to
seam edge
QUALITY POINTS
Use ruler.
Do not hold out inseam with both hands, this will stretch it.
Pant must be measured flat on a table.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
Felled Seam
All Brands
DraFix Cad
7b-Inseam
JaneR.
Crotch point
is equal to center
of diamond
INSEAM
Crotch point
is equal to
seam edge
QUALITY POINTS
Use ruler.
Do not hold out inseam with both hands, this will stretch it.
Pant must be measured flat on a table.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
FRONT RISE
All Brands
Felled Seam
Crotch point
is equal to center
of diamond
DraFix Cad
8a-Frise
JaneR.
Crotch point
is equal to
seam edge
FRONT RISE
Lay garment flat, face up.
Measure center front from crotch point to top of waistband edge.
QUALITY POINTS
Use tape measure.
Follow crotch curve.
Do not stretch.
Do not pull out straight.
Rise must lay smooth without slack.
IF SPECIAL STYLING, REFER TO MEASUREM ENT SPECS.
BACK RISE
All Brands
Felled Seam
Crotch point
is equal to center
of diamond
DraFix Cad
9a-brise
JaneR.
Crotch point
is equal to
seam edge
BACK RISE
Lay garment flat, face down, with crotch point visible.
Measure center front from crotch point to top of waistband edge.)
QUALITY POINTS
Use tape measure.
Follow crotch curve.
Do not stretch.
Do not pull out straight.
Rise must lay smooth without slack, but not stretched.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
ZIPPER FLY
All Brands
DraFix Cad
10a-Zip
JaneR.
FLY OPENING
Lay garment flat, face up.
Zipper to be unzipped and fly to be completely open.
Measure right side of zipper from bottom of waistband to top of slider.
QUALITY POINTS
Use tape measure.
Garment must be flat and smooth with no wrinkles or pleats on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS.
DraFix Cad
10b-Zip
JaneR.
All Brands
DraFix Cad
10d-Zip
JaneR.
FLY OPENING
Lay garment flat, face up.
Button to be unbuttoned, and fly to be closed.
Measure from bottom waistband seam to top of bartack at crotch join.
QUALITY POINTS
Garment must be flat and smooth with no wrinkles or pleats on underside.
IF SPECIAL STYLING, REFER TO MEASUREMENT SPECS