Escolar Documentos
Profissional Documentos
Cultura Documentos
06/2008
999800302
Method statement
GB
98003-287-01
Introduction
999800302 - 06/2008
Contents
Introduction
Page
Introduction .................................................................................................. 2
Elementary safety warnings ........................................................................ 4
Eurocodes at Doka........................................................................................ 6
System description ...................................................................................... 8
System overview ........................................................................................ 10
The Staxo 100 frame in detail.................................................................... 12
Practical examples...................................................................................... 14
Adapts to different ground plans, heights, floor shapes and loads ....... 16
Assembly (overview).................................................................................. 19
Horizontal assembly................................................................................... 20
Assembling towers in the upright ............................................................ 25
Assembling towers in the upright with mounted-ahead railings....... 25
Assembling towers in the upright:
with mounted-ahead 1.20m frames ...................................................... 30
Assembling towers in the upright by forklift truck .................................. 34
Examples of the system in action ............................................................. 36
Repositioning.............................................................................................. 37
Repositioning using wheel units ............................................................... 38
Lifting by crane ........................................................................................... 40
Lifting by forklift truck ................................................................................ 42
Structural design (overview)..................................................................... 43
Standard application: Load capacity up to 70 kN ................................... 44
Custom application: Load capacity up to 85 kN...................................... 56
Custom application: Load capacity up to 97 kN...................................... 58
General remarks ......................................................................................... 62
Combining Staxo 100 with Staxo.............................................................. 62
Anchoring on the structure........................................................................ 63
Back-stays/shoring supports for the load-bearing towers ...................... 64
Adapting to the building layout with single legs ..................................... 66
Inclination adjustment................................................................................ 69
Transporting, stacking and storing ........................................................... 70
Floor prop Eurex 60 550 ............................................................................. 72
Component overview................................................................................. 74
999800302 - 06/2008
Introduction
Planning
Provide safe workplaces for those using the
formwork (e.g. for when it is being erected/dismantled, modified or repositioned etc). It must be
possible to get to and from these workplaces via
safe access routes!
If you are considering any deviation from the
details and instructions given in this booklet, or
any application which goes beyond those
described in the booklet, then revised static calculations must be produced for checking, as well
as supplementary assembly instructions.
Assembly
The equipment/system must be inspected by the
customer before use, to ensure that it is in suitable condition. Steps must be taken to rule out the
use of any components that are damaged,
deformed, or weakened due to wear, corrosion or
rot.
Combining our formwork systems with those of
other manufacturers could be dangerous, risking
damage to both health and property. If you
intend to combine different systems, please contact Doka for advice first.
The assembly work must be carried out by suitably qualified employees of the client's.
999800302 - 06/2008
Introduction
Symbols used
Pouring
Do not exceed the permitted fresh-concrete pressures. Excessively high pouring rates lead to
formwork overload, cause greater deflection and
risk causing breakage.
Important note
Failure to observe this may lead to malfunction or damage.
Instruction
This symbol indicates that actions need to
be taken by the user.
Sight-check
Indicates that you need to do a sightcheck to make sure that necessary actions
have been carried out.
Tip
Points out useful practical tips.
Reference
Refers to other documents and materials.
Miscellaneous
We reserve the right to make alterations in the interests of technical progress.
Unless otherwise stated, all dimensions are given
in cm.
Maintenance
Only original Doka components may be used as
spare parts.
999800302 - 06/2008
Introduction
Eurocodes at Doka
In Europe, a uniform series of Standards known as
Eurocodes (EC) was developed for the construction
field by the end of 2007. These are intended to provide a uniform basis, valid throughout Europe, for
product specifications, tenders and mathematical
verification.
The EC are the world's most highly developed
Standards in the construction field.
In the Doka Group, the EC are to be used as standard from the end of 2008. They will thus supersede
Ed
Ed
Fd
Fk
Rd
Rd
Rk
115.5 [kN]
Fyield
EC/DIN concept
115.5 [kN]
90<105 [kN]
n ~ 1.65
90 [kN]
Factual
Ed
gF = 1.5
Fpermissible
A
98013-100
60 [kN]
Rd gM = 1.1
98013-102
60<70 [kN]
Rk
Factual Fpermissible
E d Rd
A Load factor
999800302 - 06/2008
999800302 - 06/2008
Introduction
System description
System description
Load-bearing tower Staxo 100 the
extra-high-capacity, fast load-bearing tower made of steel, with integral safety features
Staxo 100 comes with all the field-proven advantages of Staxo meaning that it is robust, fast and
versatile. On top of all this, Staxo 100 has been
given an extensive package of built-in safety features, and its load capacity greatly increased.
Sturdy galvanised steel frames, in three different
heights, are the basis of this high-speed, high-performance load-bearing tower system.
High load-bearing capacity, quick and easy assembly using integrated connectors, and great versatility - these are the outstanding characteristics of
Staxo.
Wherever high loads occur, in either the buildingconstruction or civil-engineering fields, this loadbearing tower is the ideal solution.
... is economical
The tower units are quick and easy to assemble:
- either on their sides or in the upright
- for tall towers, tower units can be pre-assembled on their sides, and then simply stacked by
crane
- clip-on assembly battens make it easy to erect
and dismantle the tower and the superstructure
with special wheel units, complete tableforms
can quickly be wheeled to their next location
the Forklift shifting device TG makes the job of
erecting, dismantling and transporting Doka
load-bearing towers very much easier.
... is flexible
the inter-frame spacing can be varied (from
0.60 m to 3.00 m), for optimum utilisation of the
frames' load-bearing capacity. (From 1.00m, in
50 cm increments).
different frame heights - 0.90 m, 1.20 m and
1.80 m - for rough height adjustment in 30 cm
increments: 0.90, 1.20 and 1.80 m
fine adjustment by means of screw-jack U-heads
and feet
can be used in conjunction with floor props and
Dokaflex
999800302 - 06/2008
System description
Areas of use
The Load-bearing tower Staxo is ideal:
as falsework for use in bridge-building, where
high loads occur and where great stability is
called for in that horizontal forces such as wind
loads have to be safely transferred
in the building construction field, e.g. for administration buildings and multistorey car-park
decks, where large-area tableform units reduce
forming-times
in the industrial and power-station construction
field, as a load-bearing tower for all manner of
applications
999800302 - 06/2008
System description
System overview
How to erect
b
A
Heavy duty
Screw jack U- screw jack 70
top + Split nut
head
B
U-head D
B
C
Hot-dip galvanised steel frames. Connectors for upward stacking of the frames are captively integrated into each frame.
98003-228-01
10
999800302 - 06/2008
System description
Designation
Diagonal cross 9.060
Diagonal cross 9.100
Diagonal cross 9.150
Diagonal cross 9.200
Diagonal cross 9.250
Diagonal cross 9.300
Diagonal cross 12.060
Diagonal cross 12.100
Diagonal cross 12.150
Diagonal cross 12.200
Diagonal cross 12.250
Diagonal cross 12.300
Diagonal cross 18.100
Diagonal cross 18.150
Diagonal cross 18.200
Diagonal cross 18.250
Diagonal cross 18.300
Notches
1
1
1
1
1
1
3
3
3
3
3
Note:
For horizontal bracing of the frames, always use
Diagonal crosses 9.xxx.
In levels in which assembly battens are mounted,
horizontal bracing with diagonal crosses is no
longer needed. This only applies, of course, if the
assembly battens are left in place in this "storey"
until the very end of the assignment (assembly,
pouring etc.).
999800302 - 06/2008
11
System description
Frames linked in a crane-handling-safe manner = blue locking spring (C) is pushed out.
9716-236-01
The Staxo 100 frames have the following characteristic features differentiating them from the previous
Staxo frames.
9716-211-01
Important note:
Only Staxo 100 frames meet the loading
capacity data stated in this manual!
F
B
98003-206-01
98003-229-02
98003-229-03
12
999800302 - 06/2008
System description
Safety catch
integral ladder
extra "handles" to pick the frame up by
Closed
Open
98003-255-01
98003-223-01
Warning!
Never climb up or down the outside of the
tower! You risk falling and/or causing the
tower to tip over!
Only ever climb up the inside of the
tower. When doing this, make sure that
the assembly battens are in the correct
positions (as intermediate landings)!
98003-222-01
c
a ... max. 16 cm (exception: where tubes are being connected for
constructional design purposes)
b ... Diameter 48 mm
c ... Diameter 75 mm
A Transition swivel coupler 48/76mm.
This type of link is not in conformity with DIN 4421
(DIN EN 74). No loads may be introduced parallel to the
Staxo tubes.
B Swivel coupler 48mm or Normal coupler 48mm
Profile form
98003-257-01
98003-257-01
Profile seal
prevents connection sleeve falling out
protects against damage
sliding contact surface for nuts
999800302 - 06/2008
13
System description
Practical examples
Tableforms and tower frames are both assembled
from the same system components.
Tableform units
For repetitive use, the load-bearing tower can be
assembled into complete table-forms.
Tower frames
With a load-bearing capacity of up to 97 kN per leg,
Staxo 100 is an extremely strong load-bearing
tower system.
It safely withstands horizontal forces such as wind
loads.
The wide frames make for high stability right from
the word "go".
Close inter-frame spacing is possible, for transferring high loads.
Edge floor-beam
98003-231-01
E
B
F
98003-230-01
A Load-bearing tower
B Dokaflex 1-2-4
C Beam forming support 20
D Handrail post T 1.80m, Handrail clamp S or Handrail post
1.50m
E Lashing strap 5.00 m
F Doka Express anchor 16x125mm and Doka coil 16mm
14
999800302 - 06/2008
System description
9716-222-01
98003-232-01
999800302 - 06/2008
15
System description
98003-309-01
98003-311-01
Plan view
Plan view
98003-310-01
9716-263-01
98003-268-01
98003-269-01
16
999800302 - 06/2008
Height adjustment
The 3 different heights of frame (0.90 m, 1.20 m
and 1.80 m) enable coarse adjustment to within
30 cm.
Fine adjustment, down to the last millimetre, is
done using the various head and base units.
Important note:
The structural design of the load-bearing
tower may make it necessary to plan for
shorter extension lengths. For details, see
the section headed "Structural design".
System dimensions
on multi-section towers
Regarding Table A ("Height ranges and materials
schedule"), use the version of this table given in the
chapter for the usage situation concerned.
Table B: Head zone
Heavy duty screw jack 70 top
U-head D
LK max.
LK min.
98003-236-01
98003-237-01
98003-219-04
LK
LK
LK
Values in cm
Min. values with no formwork-striking play
LF max.
LF min.
1.80m
46.2
8.2
1.20m
46.2
8.2
0.90m
46.2
26.3
98003-236-03
LF
98003-236-02
LF
98003-219-03
LF
1.80m
131.2
40.0
1.20m
131.2
100.0
0.90m
---
Values in cm
Min. values with no formwork-striking play
999800302 - 06/2008
17
on single-section towers
Note:
For towers consisting of one section only, the min.
values LK and LF given in Tables B and C for the
head and base units respectively will often not be
reached.
Reason: The lengths of the head and base units and
the integrated connector (V) in the frame add up to
a larger dimension than the height of the frame.
These constraint points have already been allowed
for in the operational height data given in Table A.
98003-238-01
a
b
c
Connector
30.5
--Screw jack foot
-69.2
-Heavy duty screw jack 70
-- 101.2
-Heavy duty screw jack 130
-- 173.0
-Screw jack U-head
--68.8
4-way screw-jack head
--68.8
Heavy duty screw jack 70 top --100.9
U-head D
--10.0
18
999800302 - 06/2008
Assembly (overview)
Assembly
Approaches to assembling the Staxo load-bearing tower 100
Horizontal assembly
(standard set-up)
98003-211-01
98003-213-01
by hand
98003-101
Railings mounted-ahead
999800302 - 06/2008
98003-293-01
98003-294-01
19
Horizontal assembly
Horizontal assembly
Preliminary remark:
The terms "vertical" and "horizontal" (e.g. referring to the diagonal crosses) are always used
here with reference to their installation situation
in the finished, upright tower.
The job of erecting the load-bearing tower begins
with the bottom (i.e. first) section.
Arrow on frame must be pointing upwards.
(= yellow locking spring at bottom)
98003-206-01
General remarks:
As soon as you have slotted a diagonal
cross onto the latch-type peg, secure it
with the safety catch.
98003-216-01
98003-216-02
Basic rule:
98003-286-01
98003-215-01
20
999800302 - 06/2008
Horizontal assembly
98003-213-02
98003-303-01
98003-213-01
h ... max. 10 m
999800302 - 06/2008
21
1
M
2
M
3
L
98003-312-01
98003-312-02
Close-up 1
22
98003-312-04
98003-312-03
Close-ups 2 and 3
999800302 - 06/2008
Important note:
Erect the load-bearing tower in the vertical on ground that is statically capable of
supporting the load.
If the load-bearing tower is over 6 m high,
back-stay it or combine it with other towers.
Horizontal assembly
98003-218-01
Dismantling
After the tower has been placed back on its side, it
can be dismantled in reverse order.
98003-214-01
999800302 - 06/2008
23
Horizontal assembly
24
999800302 - 06/2008
Important note:
Erect the load-bearing tower in the vertical on ground that is statically capable of
supporting the load.
If the load-bearing tower is over 6 m high,
back-stay it or combine it with other towers.
98003-256-01
98003-206-01
General remarks:
Arrow on frame must be pointing upwards.
(= yellow locking spring at bottom)
98003-233-01
999800302 - 06/2008
25
Mount Staxo 100 side railings (L) above the diagonal crosses.
L
98003-251-01
E
E
98003-251-02
B
98003-234-01
M
F
98003-210-01
98003-250-01
26
98003-250-02
98003-250-03
999800302 - 06/2008
98003-209-01
98003-272-01
98003-209-02
Frames linked in a crane-handling-safe manner = blue locking spring (C) is pushed out.
98003-229-04
98003-229-01
98003-207-01
999800302 - 06/2008
27
Horizontal bracing
Important note:
If no assembly battens are used, or if these
are removed before the end of the assignment, the following rule applies.
Basic rule:
2
2
98003-285-01
98003-208-01
98003-211-01
28
999800302 - 06/2008
Head zone
Dismantling
98003-212-02
9716-215-01
Warning!
Where the primary beams cantilever out
a long way, protect them against being
lifted out or tipped over (e.g. by nailing
board-plates over the beam joins, or by
fastening them to the head unit).
Important note:
When lifting and repositioning the entire
tower unit (or pre-assembled sub-units)
by crane: Follow the instructions in the
section headed "Lifting by crane"!
999800302 - 06/2008
29
Important note:
Erect the load-bearing tower in the vertical on ground that is statically capable of
supporting the load.
If the load-bearing tower is over 6 m high,
back-stay it or combine it with other towers.
General remarks:
Arrow on frame must be pointing upwards.
(= yellow locking spring at bottom)
98003-205-01
C
E
98003-265-01
98003-233-01
30
98003-263-01
999800302 - 06/2008
98003-273-01
98003-209-02
98003-262-01
Frames linked in a crane-handling-safe manner = blue locking spring (C) is pushed out.
98003-229-04
98003-229-01
98003-274-01
999800302 - 06/2008
31
Horizontal bracing
Important note:
If no assembly battens are used, or if these
are removed before the end of the assignment, the following rule applies.
Basic rule:
Horizontal diagonal crosses 9.xxx are needed:
at intervals of every two storeys - beginning
with the first storey.
Slot diagonal crosses (K) onto the gravity latches
of the horizontal frame tubes and secure them.
98003-285-01
98003-264-01
98003-261-01
32
999800302 - 06/2008
Head zone
98003-212-02
9716-215-01
98003-259-01
Warning!
Where the primary beams cantilever out
a long way, protect them against being
lifted out or tipped over (e.g. by nailing
board-plates over the beam joins, or by
fastening them to the head unit).
Important note:
When lifting and repositioning the entire
tower unit (or pre-assembled sub-units)
by crane: Follow the instructions in the
section headed "Lifting by crane"!
Dismantling
To dismantle, perform the above steps in reverse
order.
999800302 - 06/2008
33
with superstructure
without superstructure
Tr745-200-05
92807-201-01
a
b
c
d
G
Items needed:
Designation
Forklift shifting device TG
Multi-purpose walings WS10 Top50 2.00m
Connecting pins 10cm
Spring cotters 6mm
Scaffolding tubes 48.3mm 1.00m
Screw-on couplers 48mm 50
Scaffolding tube 48.3mm 2.00m
Swivel couplers 48mm
Operating cord, site-provided (optional)
H
C D
Item
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
Q'ty
1
2
4
4
2
4
1
2
1
Warning!
It is not permitted to use non-enclosed
(open) fork extensions.
92807-208-01
92807-207-01
Warning!
While load-bearing towers are being
erected or dismantled, lifted or lowered: It
is forbidden to walk or stand beneath suspended loads.
Max. load:
when using box-style fork extensions: 1000 kg
when using telescopic fork prongs: 600 kg
34
999800302 - 06/2008
Tr745-200-05
Dismantling
To dismantle, perform the above steps in reverse
order.
Important note:
Always only dismantle the bottom "storey"
of the towerframe unit.
999800302 - 06/2008
35
36
999800302 - 06/2008
Repositioning
Repositioning
Different ways of repositioning
Transport winches
98003-298-01
999800302 - 06/2008
By crane
By forklift truck or
telescoping stacker truck
Shifting carriage TG
98003-296-01
98003-299-01
98003-300-01
37
Repositioning
The floor must be stable, firm and sufficiently smooth (e.g. concrete).
Follow the directions in the Operating
Instructions!
9716-259-01
Wheel-unit variants:
Shifting carriage TG
Modular system (with winches)
Important note:
On standard superstructures, the max.
width-to-height ratio of the table+tower is
1:3 (W:H). A statical check must be performed on custom constructions.
D
C
98003-226-01
38
Designation
N of items
Winch 70 or 125
4
Frame for Staxo/d2 winch
4
Solid-tyre wheel or Heavy-duty wheel 15kN
4
Double wheeled transporter
4
999800302 - 06/2008
Repositioning
Shifting carriage TG
This is an easy-to-operate, manual hydraulic lifting
carriage for shifting light to medium-weight tableform units. As well as making the tableforms easier
to move around, it also makes it easier to erect and
strike the formwork.
Hydraulic, for near-effortless lifting.
Tables can be "inched" down slowly with handlecontrol.
3 guide-rolls, for maximum manoeuvrability.
With an overall width of only 82 cm, the carriage
can pass easily through any doorway when
empty.
The floor must be stable, firm and sufficiently smooth (e.g. concrete).
Max. gradient of floor: 5 %.
Max. configuration that can be transported using 2 Shifting carriages TG:
Tables with 3 cross-frames per section
and a max. height of 5.0 m.
Follow the directions in the Operating
Instructions!
A
98003-225-01
999800302 - 06/2008
Designation
Shifting carriage TG
N of items
2
39
Repositioning
Lifting by crane
Important note:
The max. height of towerframe unit that can
be lifted in one piece is 20 m!
Max. load:
1000 kg per Lifting rod 15.0 - where the load is
applied centrally
Mounting instructions
Only possible with Clamping
plate a = 28 cm (2002 models
onward)
5.1
9716-285-01
Preparations
Warning!
Danger from loose and unsecured parts.
Observe the following points before lifting!
Secure the base units to prevent them dropping out: On Screw jack foot (H) and Heavy
duty screw jack 70 or 130 using Split nut B
Slot the fixing-handle (I) into the cross-bar of the
frame.
9716-239-01
40
999800302 - 06/2008
Repositioning
98003-229-04
L
9716-230-01
Lifting operation
Attach the crane sling to the Lifting rods 15.0 and
lift the tableform to its next location.
Spread-angle max. 30.
M
9716-231-01
9716-229-01
9716-232-01
999800302 - 06/2008
41
Repositioning
with superstructure
Tr745-200-05
a
b
c
d
42
999800302 - 06/2008
Structural design
Structural-design configurations
Load-bearing tower Staxo 100
Standard application
98003-254-01
98003-240-01
1.80 m
1.20 m
0.90 m
98003-253-01
Custom applications
1.20 m
0.90 m
1.20 m
0.90 m
Top and bottom "storeys" MUST
be with 0.90m frames
Load-bearing
tower held at
top
45 cm
70 cm*
Free-standing
load-bearing
tower
30 cm
45 cm*
70 cm
130 cm*
30 cm
45 cm*
30 cm
45 cm*
25 cm**
40 cm*
30 cm
45 cm*
25 cm**
40 cm*
Important note:
For the extension lengths marked with an *,
suitable bracing of the head and base units
is required.
For the extension lengths marked **, the
integrated connection sleeve must be
removed from the frame.
999800302 - 06/2008
43
LF
LF
h
Fh
LK
98003-219-01
44
999800302 - 06/2008
Table A
2.78 - 2.95
2.78 - 3.55
--3.24 - 3.85
3.54 - 4.15
3.24 - 4.45
3.54 - 4.75
4.44 - 5.05
4.14 - 5.35
4.44 - 5.65
4.74 - 5.95
5.04 - 6.25
5.34 - 6.55
5.64 - 6.85
5.94 - 7.15
6.24 - 7.45
6.54 - 7.75
6.84 - 8.05
7.14 - 8.35
7.44 - 8.65
7.74 - 8.95
8.04 - 9.25
8.34 - 9.55
8.64 - 9.85
8.94 - 10.15
9.24 - 10.45
9.54 - 10.75
9.84 - 11.05
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
h [m]
min. - max.
Basic items
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2.06 - 2.35
2.06 - 2.95
2.52 - 2.95
2.52 - 3.25
2.82 - 3.55
2.92 - 3.85
3.22 - 4.15
3.52 - 4.45
3.82 - 4.75
4.12 - 5.05
4.42 - 5.35
4.72 - 5.65
5.02 - 5.95
5.32 -6.25
5.62 - 6.55
5.92 - 6.85
6.22 - 7.15
6.52 - 7.45
6.82 - 7.75
7.12 - 8.05
7.42 - 8.35
7.72 - 8.65
8.02 - 8.95
8.32 - 9.12
8.62 - 9.55
8.92 - 9.85
9.22 - 10.15
9.52 - 10.45
98003-113
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
98003-113
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
h [m]
min. - max.
Variant 3
LK = max. 45 cm
LF = max. 130 cm
1.75 - 1.80
2.02 - 2.40
2.20 - 2.40
2.32 - 2.70
2.62 - 3.00
2.92 - 3.30
3.22 - 3.60
3.52 - 3.90
3.82 - 4.20
4.12 - 4.50
4.42 - 4.80
4.72 - 5.10
5.02 - 5.40
5.32 - 5.70
5.62 - 6.00
5.92 - 6.30
6.22 - 6.60
6.52 - 6.90
6.82 - 7.20
7.12 - 7.50
7.42 - 7.80
7.72 - 8.10
8.02 - 8.40
8.32 - 8.70
8.62 - 9.00
8.92 - 9.30
9.22 - 9.60
9.52 - 9.90
h [m]
min. - max.
Variant 2
LK = max. 45 cm
LF = max. 70 cm
1.20
1.80
1.80
2.10
2.40
2.70
3.00
3.30
3.60
3.90
4.20
4.50
4.80
5.10
5.40
5.70
6.00
6.30
6.60
6.90
7.20
7.50
7.80
8.10
8.40
8.70
9.00
9.30
98003-113
Variant 1
LK = max. 30 cm
LF = max. 30 cm
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
2
2
2
4
2
2
4
4
2
6
4
4
6
6
4
8
6
6
8
8
6
10
8
1
1
5
3
1
3
1
4
1
4
2
4
2
4
2
4
2
4
2
5
2
5
3
5
3
5
3
5
2
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
2
2
2
4
2
2
4
4
2
6
4
4
6
6
4
8
6
6
8
8
6
10
8
999800302 - 06/2008
45
Selection diagram
Staxo 100 load-bearing tower
Held at top
Free-standing
98003-305-01
9716-314-01
e 50 cm
Inter-frame space 1.5 - 3.0 m
Diagrams 2 and 3
Inter-frame space 0.6 - 1.0 m
Diagrams 6 and 7
46
9716-314-02
Important note:
Separate proof must be provided, by a suitably skilled person, regarding the foundation. Particular attention must be paid here
to the ground-bearing pressure!
9716-314-05
9716-314-01
9716-314-02
9716-314-05
98003-304-01
e 50 cm
Inter-frame space 1.5 - 3.0 m
Inter-frame space 1.5 - 3.0 m
Diagrams 14 and 15
Diagrams 16 and 17
Inter-frame space 1.0 m
Inter-frame space 1.0 m
Diagrams 18 and 19
Diagrams 20 and 21
Statical proof must be provided for both the bracing-strut plane and
the frame plane.
Inclination adjustment
Inclination is adjusted with a wooden wedge = no
effect on the restraint situation.
- e.g. with Wedge for screw jack U-head or
Staxo wedge support
Inclination is adjusted with a centering strip =
Screw jack U-head not restrained.
- e.g. with Hexagon screw M20x230
999800302 - 06/2008
W
E
F
Z
D
98003-228-02
Bracing-strut plane:
e.g. LF1 = 25 cm, LF2 = 75 cm: B1 (no need for bracing with scaffolding tubes)
Frame plane 1: (on the right in the illustration)
e.g. LF1 = 75 cm, LF2 = 75 cm: B2 (bracing with scaffolding tubes
required)
Frame plane 2: (on the left in the illustration)
e.g. LF1 = 25 cm, LF2 = 25 cm: A (no need for bracing with scaffolding tubes)
B2
70
F
Z
B1
A
0
30
130
70
E Diagonal cross
F Split nut B
W Staxo frame
Z Scaffolding tube 48.3mm
Frame plane
LK
LK
Bracing-strut plane
98003-248-01
98003-112
30
W
Y
Z
LF2
LF2
a
LF1
LF1
98003-243-01
98003-288-01
999800302 - 06/2008
47
FV
Frame plane
FV
FV
FV
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.80/1.20/0.90m
X Screw jack foot or Heavy duty screw jack
Z Scaffolding tube 48.3mm with Swivel couplers 48mm (only required
in Range B2 as shown in Diagram 1)
The following diagrams do not apply to load-bearing towers that are
only one Staxo 100 frame high.
LF
X
X
Z
98003-244-01
9716-314-01
100
100
90
90
65.0
61.0
63.8
A 65.4
B 62.4
50
40
30
70
60
55.2 55.2
50
10
15
20.40 m
98003-102
13.20 m
6.00 m
16.80 m
10
9.60 m
10
50.7
50.8
47.2
A
B
49.3
44.6
43.2
48.1
42.4
30
20
49.4 49.4
40
20
53.3
53.8 53.8
20
10
15
20.95 m
98003-103
65.8
17.35 m
66.2
13.75 m
64.0
60
66.2
65.4
62.9
10.15 m
66.2
65.7
70.0
69.6
68.2
70
80
6.55 m
80
4.75 m
4.20 m
e 50 cm
20
48
999800302 - 06/2008
FV
Frame plane
FV
FV
FV
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.80/1.20/0.90m
X Screw jack foot or Heavy duty screw jack
Z Scaffolding tube 48.3mm with Swivel couplers 48mm (only required
in Range B2 as shown in Diagram 1)
The following diagrams do not apply to load-bearing towers that are
only one Staxo 100 frame 1.80m high.
LF
X
X
Z
98003-244-01
9716-314-05
100
100
90
90
54.6
50
56.4
55.4
52.3
55.8
55.3
A 55.0
53.5 B 52.7
54.4
50.2
40
30
60
50
40
10
15
98003-104
20.40 m
13.20 m
6.00 m
16.80 m
10
9.60 m
10
45.2
43.6
42.6
20
A
B
45.2
45.0
41.2
39.8
C
33.8
30
20
45.2
37.6
20
45.2 45.2
43.9 43.9
40.3 40.3
10
15
20.95 m
98003-105
60
70
17.35 m
57.3
56.6
13.75 m
67.2
66.4
63.9
10.15 m
70
80
6.55 m
80
4.75 m
4.20 m
9716-314-02
20
999800302 - 06/2008
49
FV
Frame plane
FV
FV
FV
a ... 1.0 m
h ... see diagrams
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.80/1.20/0.90m
X Screw jack foot or Heavy duty screw jack
Z Scaffolding tube 48.3mm with Swivel couplers 48mm (only required
in Range B2 as shown in Diagram 1)
LF
98003-245-01
9716-314-01
100
100
90
90
65.0
62.0
65.7
A
63.7 B
64.9
63.7
61.3
57.9
56.8
50
40
30
70
60
52.3 52.3
50
44.9
40
10
15
20.40 m
98003-106
13.20 m
6.00 m
16.80 m
10
9.60 m
10
44.9
44.3
42.3
42.1
38.7
30
20
A 46.5
46.1
36.8
20
49.2
50.5 50.5
20
10
15
20.95 m
98003-107
63.6
60
66.0
17.35 m
66.0
65.4
13.75 m
70
80
10.15 m
70.3
70.0
68.9
6.55 m
80
4.75 m
4.20 m
e 50 cm
20
50
999800302 - 06/2008
FV
Frame plane
FV
FV
FV
a ... 1.0 m
h ... see diagrams
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.80/1.20/0.90m
X Screw jack foot or Heavy duty screw jack
Z Scaffolding tube 48.3mm with Swivel couplers 48mm (only required
in Range B2 as shown in Diagram 1)
LF
98003-245-01
9716-314-05
100
100
90
90
54.8
53.0
50
53.6
49.9
54.0
A
52.1 B
53.6
50.8
46.1
53.2
47.9
40
30
60
50
43.6 43.6
40
37.7 37.7
10
15
20.40 m
13.20 m
6.00 m
98003-108
10
16.80 m
10
9.60 m
20
20
40.6 B
42.3
41.2
38.5
39.9
36.0
32.7
30
20
43.2 A
42.1 42.1
10
15
20.95 m
98003-109
55.9
55.2
17.35 m
60
70
13.75 m
63.2
62.3
59.6
10.15 m
70
80
6.55 m
80
4.75 m
4.20 m
9716-314-02
20
999800302 - 06/2008
51
FV
Frame plane
FV
FV
FH
FH
FH
FV
FH
LK
Statical proof must be provided for both the bracing-strut plane and
the frame plane.
For the dimensioning calculation, it is the smaller of the two results
that is relevant.
LF
h
B
A Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
B Staxo 100 frames 1.80/1.20/0.90m
C Screw jack foot or Heavy duty screw jack
98003-290-01
in frame plane
98003-306-02
Diagram 15
100
100
63.5
60
61.7
56.5
50
59.3
A
57.7
55.6 B
49.1 C
50.0
50.1
40
35.0
30
D 30.0
17.0
3.3
0
0.0
8.5
0.5
1.0
E
1.70
20
10
36.5
29.5
1.5
2.0
70
66.2
60
64.5
60.4
50
A
B
60.4
53.8
40
40.3
34.0
30
20
9.3
10
7.5
2.0
0
0.0
0.5
1.0
D
E
1.5
15.5
16.3
98003-115-01
66.2
98003-114-01
70
80
1.70
80
90
1.35
90
Diagram 14
1.35
98003-306-02
2.0
52
999800302 - 06/2008
FV
Frame plane
FV
FV
FH
FH
FH
FV
FH
LK
Statical proof must be provided for both the bracing-strut plane and
the frame plane.
For the dimensioning calculation, it is the smaller of the two results
that is relevant.
LF
h
B
A Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
B Staxo 100 frames 1.80/1.20/0.90m
C Screw jack foot or Heavy duty screw jack
98003-290-01
in frame plane
98003-306-01
Diagram 17
100
100
60
56.9
A B C
50
48.2
43.7
40
37.0
35.0
30
23.2
20
3.3
0
0.0
0.5
8.5
1.0
1.5
98003-116-01
10
17.0
2.0
70
60
57.3
A B C
54.2
52.0
50
40
34.0
30
20
9.3
10
7.5
2.0
0
0.0
0.5
1.0
15.5
D
E
13.7
1.5
98003-117-01
70
80
1.70
80
90
1.20
90
Diagram 16
1.70
98003-306-01
2.0
999800302 - 06/2008
53
Frame plane
FVR*1.25
FVR
FVR
FH
FH
FV
FH
FH
FV
FH
LK
LF
Statical proof must be provided for both the bracing-strut plane and
the frame plane.
For the dimensioning calculation, it is the smaller of the two results
that is relevant.
9800-291-01
in frame plane
98003-306-02
Diagram 19
100
100
60
56.4
56.0
50
54.8
52.4
51.5
49.1
48.7
47.2
40
A
B
42.0
41.5
41.3
31.3
30
27.0
12.0
10
10.0
2.6
0
0.0
D
E
0.5
1.0
1.80
20
1.5
98003-118-01
22.0
19.6
2.0
70
66.2
60
64.5
60.4
50
A
B
60.4
53.8
40
40.3
34.0
30
20
9.3
10
7.5
2.0
0
0.0
0.5
1.0
D
E
1.5
15.5
16.3
98003-119-01
70
80
1.70
80
90
1.35
90
Diagram 18
1.70
98003-306-02
2.0
54
999800302 - 06/2008
Frame plane
FVR *1.25
FVR
FVR
FH
FH
FV
FH
FH
FV
FH
LK
LF
Statical proof must be provided for both the bracing-strut plane and
the frame plane.
For the dimensioning calculation, it is the smaller of the two results
that is relevant.
9800-291-01
in frame plane
98003-306-01
Diagram 21
100
100
60
46.4
A B C
40
38.6
34.4
32.8
30
27.0
19.6
20
12.0
10
18.4
10.0
2.6
0
0.0
D
E
0.5
1.0
1.5
98003-120-01
50
2.0
70
60
57.3
A B C
54.2
52.0
50
40
34.0
30
20
9.3
10
7.5
2.0
0
0.0
0.5
1.0
15.5
D
E
13.7
1.5
98003-121-01
70
80
1.70
80
90
1.20
90
Diagram 20
1.70
98003-306-01
2.0
999800302 - 06/2008
55
1.75 - 1.80
2.18 - 2.40
2.32 - 2.70
2.62 - 3.00
3.10 - 3.30
3.22 - 3.60
3.52 - 3.90
3.82 - 4.20
4.12 - 4.50
4.42 - 4.80
4.72 - 5.10
5.02 - 5.40
5.32 - 5.70
5.62 - 6.00
5.92 - 6.30
6.22 - 6.60
6.52 - 6.90
6.82 - 7.20
7.12 - 7.50
7.42 - 7.80
7.72 - 8.10
8.02 - 8.40
8.32 - 8.70
8.62 - 9.00
8.92 - 9.30
9.22 - 9.60
9.52 - 9.90
LF
h [m]
min. - max.
h
Fh
LF
98003-220-01
1.20
1.80
2.10
2.40
2.70
3.00
3.30
3.60
3.90
4.20
4.50
4.80
5.10
5.40
5.70
6.00
6.30
6.60
6.90
7.20
7.50
7.80
8.10
8.40
8.70
9.00
9.30
98003-113
Basic items
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
6
4
2
6
4
2
6
4
2
6
4
2
6
4
2
6
4
2
2
2
4
2
4
6
2
4
6
8
4
6
8
10
6
8
10
12
8
10
12
14
10
12
14
1
5
3
1
8
6
4
2
8
6
4
2
9
7
5
3
9
7
5
3
10
8
6
4
10
8
6
2
2
4
2
4
6
2
4
6
8
4
6
8
10
6
8
10
12
8
10
12
14
10
12
14
56
Important note:
Greater extension lengths are possible
(up to max. 45 cm) if the head units and/or
base units are given suitable scaffoldingtube bracing.
In principle, it is possible to use Heavy
duty screw jacks 70 and "Heavy duty
screw jacks 70 top". However, when these
are combined with the small frames, the
limitations given in Tables B and C on
Page 15 "System dimensions" must be
observed.
999800302 - 06/2008
FV
Frame plane
FV
FV
FV
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.20/0.90m
X Screw jack foot or Heavy duty screw jack 70
Z Scaffolding tube 48.3mm with Swivel couplers 48mm
X
Z
The following diagram does not apply to load-bearing towers that are
only one Staxo 100 frame high.
LF
98003-292-01
a = 1.0 m
a = 0.6 m
A
84.5 kN
80.9 kN
B
82.9 kN
74.4 kN
C
78.1 kN
54.9 kN
Max. height of load-bearing tower: 11.4 m
9716-314-01
e 50 cm
Y
85.0
83.8
83.7
82.4
80
79.7
81.6
A
B
82.3
LK
85.7
84.9
85.8
85.3
83.9
78.3
75.2
70
D
98003-289-01
90
60
50
40
F Split nut B
30
10
15
21.00 m
98003-110
16.20 m
6.60 m
4.20 m
10
11.40 m
20
20
999800302 - 06/2008
Y If the "Heavy duty screw jacks 70 top" are not joined by multipurpose walings and Doka beams, then horizontal bracing
(with scaffolding tubes) must be fitted in the direction concerned.
57
Important note:
2.18 - 2.30
3.08 - 3.20
3.38 - 3.50
3.98 - 4.10
4.28 - 4.40
4.58 - 4.70
4.88 - 5.00
5.18 - 5.30
5.48 - 5.60
5.78 - 5.90
6.08 - 6.20
6.38 - 6.50
6.52 - 6.80
6.82 - 7.10
7.12 - 7.40
7.42 - 7.70
7.72 - 8.00
8.02 - 8.30
8.32 - 8.60
8.62 - 8.90
8.92 - 9.20
9.22 - 9.50
9.52 - 9.80
LF
h [m]
min. - max.
h
Fh
LF
98003-221-01
1.80
2.70
3.00
3.60
3.90
4.20
4.50
4.80
5.10
5.40
5.70
6.00
6.30
6.60
6.90
7.20
7.50
7.80
8.10
8.40
8.70
9.00
9.30
98003-113
Basic items
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
8
6
4
10
8
6
4
10
8
6
4
10
8
6
4
10
8
6
4
10
2
2
4
2
4
6
2
4
6
8
4
6
8
10
6
8
10
12
8
5
8
6
10
8
6
13
11
9
7
13
11
9
7
14
12
10
8
14
12
10
8
15
2
2
4
0
2
4
6
2
4
6
8
4
6
8
10
6
8
10
12
8
58
999800302 - 06/2008
FV
Frame plane
FV
FV
FV
LK
V Screw jack U-head, 4-way screw-jack head, Heavy duty screw jack 70
top or U-head D
W Staxo 100 frames 1.20/0.90m
(0.90m compulsory in the bottom and top "storeys")
X Screw jack foot or Heavy duty screw jack 70
Z Scaffolding tube 48.3mm with Swivel couplers 48mm
W
X
Z
The following diagram does not apply to load-bearing towers that are
only one Staxo 100 frame high.
LF
X
98003-295-01
9716-314-01
LK
e 50 cm
D
Diagram 11
97.0
96.8
96.0
90
95.9
95.5
94.3
94.7
93.9
91.4
93.0
91.5
A
B
87.0
98003-289-01
100
91.2
88.5
80
70
60
50
Y If the "Heavy duty screw jacks 70 top" are not joined by multipurpose walings and Doka beams, then horizontal bracing
(with scaffolding tubes) must be fitted in the direction concerned.
40
30
10
15
20.30 m
98003-111
15.50 m
5.90 m
3.50 m
10
10.70 m
20
20
999800302 - 06/2008
59
Removing
Using e.g. a tie-rod, push the connection sleeve
upwards until it hits the stop.
98003-301-01
98003-301-03
98003-301-04
98003-301-02
60
999800302 - 06/2008
Installation
Use a screwdriver to press the spring out of the
way.
Push the connection sleeve into the frame tube
from below, until it hits the stop (make sure that
the spring (A) is in the right position).
98003-313-02
98003-313-01
98003-313-03
999800302 - 06/2008
61
General remarks
62
Important note:
In principle, the system frames of the Loadbearing towers Staxo and Staxo 100 are
compatible with one another. Ideally, however, tower frames should each be assembled from components of the same system
(i.e. "mono-system"). The diagrams in the
User Information booklet and type-test only
apply to mono-system tower frames.
If this is not possible, then the following
points must be remembered:
The lower leg loads permitted for the
Staxo system must be assumed.
- Custom applications with permitted
capacities of 85 or 97 kN per leg are not
possible
- No type-test
At the very least, each "storey" must be
assembled from components of the same
system (because the two systems use different horizontal diagonal braces).
For details regarding structural design, setup and use, see the User Information booklet
"Doka load-bearing tower Staxo" !
999800302 - 06/2008
General remarks
At the level of the anchoring point, the loadbearing tower must be stiffened with a diagonal cross (H) .
B
C
H
E
D
98003-282-01
999800302 - 06/2008
98003-247-01
63
General remarks
Zk Qk = Hk
18.2 26.0
27.6 21.2
44.8 15.0
Rk Zd Qd = Hd Rd
31.7 27.3 39.0 47.6
34.8 41.4 31.8 52.2
47.2 67.2 22.5 70.8
D E
Zk Qk = Hk
24.3 34.6
36.8 28.3
59.7 20.0
Rk Zd Qd = Hd Rd
42.3 36.5 51.9 63.5
46.4 55.2 42.5 69.6
62.9 89.6 30.0 94.4
A
V
Z k Q k = Hk R k
Zd Qd = Hd Rd
30.4 43.3 52.9 45.6
65.0
79.4
46.0 35.4 58.0 69.0
53.1
87.0
74.6 25.0 78.7 111.9 37.5 118.1
C
98003-249-01
Caution!
The "Back-stay for load-bearing towers"
must not be dismounted until it is certain
that there is sufficient stability for the
load-bearing tower.
64
999800302 - 06/2008
General remarks
30
25
20
15
10
5
0
9745-101
10
11
12
13
14
B
A
A
C
Caution!
The plumbing strut must not be dismounted until it is certain that there is
sufficient stability for the load-bearing
tower.
98003-308-01
999800302 - 06/2008
65
General remarks
98003-276-01
Warning!
Allow for the reduced loading capacities!
For standard applications (perm. Fv =
70 kN per leg) the rule is:
The permitted vertical load on the single
leg must be reduced by 30% as compared
with the loading capacity data given for
the various loading cases (in the dimensioning diagrams)!
For custom applications (perm. Fv = 85 or
97 kN per leg) the rule is:
Permitted capacity max 50 kN per leg.
Max. height of tower: 10.0 m
Can only be used on top-held load-bearing towers.
66
Note:
To facilitate the assembly work, we recommend
using a Doka mobile scaffold tower Z or a standard
platform trolley.
999800302 - 06/2008
Tower-type solution
General remarks
Triangle-type solution
a
C
E
B
A
C
98003-275-01
98003-267-01
a ... 25 - 150 cm
A Staxo 100 single leg 1.80, 1.20 or 0.90 m
a ... 25 - 150 cm
A Staxo 100 single leg 1.80, 1.20 or 0.90 m
E Diagonal cross
(the type will depend on the size of frame and the interframe space)
Practical examples
F Diagonal cross 9.xxx (in range 'a' from 120 - 150 cm otherwise use a scaffolding tube as bracing)
Basic rule:
Horizontal diagonal crosses 9.xxx are needed:
at intervals of every two storeys - beginning
with the first storey.
98003-270-01
Practical examples
Reducing the number of legs (instead of 2 tower
units, an extra leg-plane is added to one side of
the tower).
Wheeling
Important note:
Before a Staxo tower with extra legs can be
wheeled, vertical bracing (G) must be added
in the bottom "storey" between these single
legs and the Staxo 100 tower!
C
G
98003-271-01
98003-284-01
999800302 - 06/2008
67
General remarks
68
999800302 - 06/2008
General remarks
Inclination adjustment
If the superstructure or the ground are inclined at
an angle of 1% or more, slope compensation must
be provided.
Inclined superstructures
Securing the superstructure at angles of over 12%:
Connect the head-plate to the longitudinal beam
(e.g. with Locking rod 15.0/33cm and Super-plate
15.0 or Angle anchor plate 12/18)
a ... min. 15 cm
A Staxo wedge support WS10
B Timber wedge, project-specific
C Multi-purpose waling or Steel waling WS10 Top50
D Nailed connection
Note:
If the legs of the load-bearing tower have to be
located outside the pattern of drilled holes in the
multi-purpose waling or steel waling, then a suitable 20 mm diam. hole must be drilled in the web of
the waling.
9703-255-01
D
9703-254-01
A
9716-292-01
999800302 - 06/2008
69
General remarks
98003-246-01
The Bolt-on caster set B can be mounted to the following multi-trip packaging items:
Doka stacking pallets
Doka accessory box
70
999800302 - 06/2008
General remarks
Tr755-200-02
Lengthways
Crossways
max. 3 partitions
max. 3 partitions
Tr755-200-04
999800302 - 06/2008
Tr755-200-05
71
Product description
The perfect complement to all Doka load-bearing
towers.
Transfers loads economically, also in confined
spaces.
Extension range: 3.50 to 5.50 m
For even greater heights, the prop can be lengthened to 7.50 m or 11.0 m. In this case, allow for
the reduction in capacity as shown in the diagram!
Meets "DIB" - German Institute of Building Technology - approvals criteria.
Special aluminium profile tubes give the prop its
low weight of only 47.0 kg.
9745-211-01
50
40
30
20
10
0
98003-314-01
72
9745-100
10
11
12
999800302 - 06/2008
9745-201-01
9745-201-01
Mounting instructions
Place the U-head or four-way head on the prop
and fix with spring-steel stirrup.
9745-212-01
98003-315-01
Bracing
Examples:
between prop and load-bearing tower frame
between two or more props
to facilitate erection of the prop (as a "handle" for
workers to hold onto)
9745-203-01
C
B
A
9703-256-01
999800302 - 06/2008
73
Component overview
[kg] Article n
[kg] Article n
Doka Load-bearing
Load-bearing
tower Towers
Staxo
37.0 582300000
28.0 582301000
24.0 582302000
Staxo 100-Rahmen
9.2 582327000
Height: 106 cm
Galvanised
Split nut B
2.0 582634000
Spannmutter B
3.1
4.1
5.2
5.7
6.6
8.0
10.0
4.2
4.6
5.7
6.1
6.9
8.3
9.0
6.1
6.9
7.3
7.8
9.1
10.3
Diagonalkreuz
582322000
582772000
582773000
582627000
582774000
582775000
582323000
582324000
582610000
582612000
582628000
582614000
582616000
582325000
582620000
582622000
582629000
582624000
582626000
582326000
Galvanised
The split nut B must not be opened
until the heavy-duty screw jack has
had the load taken off it.
2.0 502709030
Klemmplatte fr Gabelkopf
Galvanised
Length: 24 cm
Width: 9 cm
0.31 581961000
Flgelmutter 15,0
Galvanised
Length: 10 cm
Height: 5 cm
Width-across: 27 mm
Packed in units of 80
Perm. capacity with safety factor of
1.6: 120 kN
Perm. capacity to DIN 18216: 90 kN
Breaking load: > rod breaking load (>
195 kN)
Galvanised
0.48 582641000
Quetschteil 15,0
Galvanised
Width-across: 24 mm
Never weld or heat tie-rods - risk of
fracture!
6.7 582709000
Gabelkopf D
8.7 582796000
Staxo-Keilauflager WS10
Galvanised
Length: 31 cm
Width: 15 cm
Height: 23 cm
Galvanised
Length: 20 cm
Width: 22 cm
Height: 37 cm
10.4 582638000
Vierwegkopfspindel
0.46 176071000
Spindelkeil ..... %
Length: 20 cm
Width: 16 cm
Galvanised
Height: 86 cm
9.0 582637000
Fuspindel
Galvanised
Height: 69 cm
9.2 582636000
Kopfspindel
Galvanised
Height: 74 cm
74
999800302 - 06/2008
Component overview
[kg] Article n
Heavy duty screw jack 70
8.8 582639000
Lastspindel 70
[kg] Article n
Extension Eurex 60 2.00m
Powder-coated, blue
Aluminium
Length: 250 cm
Galvanised
Height: 101 cm
During shifting, this must be pushed
up into the frame and secured.
18.0 582651000
13.0 582711000
Lastspindel 130
Galvanised
Height: 173 cm
During shifting, this must be pushed
up into the frame and secured.
Coupler Eurex 60
8.6 582652000
Kupplungsstck Eurex 60
Aluminium
Length: 100 cm
Diameter: 12.8 cm
U-head Eurex 60
2.9 582656000
Gabelkopf Eurex 60
24.0 582303000
21.5 582304000
20.2 582305000
Staxo 100-Einzelstiel
Galvanised
Length: 22 cm
Width: 20 cm
Height: 12 cm
4.5 582655000
Vierwegkopf Eurex 60
Galvanised
Galvanised
Length: 25 cm
Width: 21 cm
Height: 21 cm
42.5 582658000
47.0 582650000
Powder-coated, blue
Aluminium
Length: 343 - 553 cm
Aluminium
Height: 345 - 555 cm
Perm. capacity: 60 kN at any telescoping length
7.1 582665000
Galvanised
Height: 50 cm
999800302 - 06/2008
75
Component overview
Connector Eurex 60
3.9 582657000
Verbindungsstck Eurex 60
[kg] Article n
Removable folding tripod 1.20m
Galvanised
Length: 15 cm
Width: 15 cm
Height: 30 cm
Galvanised
Height: 120 cm
8.5 582660000
Galvanised
Length: 31 cm
Width: 12 cm
Height: 33 cm
20.7 586145000
Sttzbein 1,20m
0.31 588631000
Doka-Expressanker 16x125mm
Galvanised
Length: 18 cm
Packed in units of 10
Follow fitting instructions!
1.0 582654000
Galvanised
Width-across: 22 mm
0.009 588633000
Doka-Coil 16mm
Galvanised
Diameter: 1.6 cm
Packed in units of 100
Follow fitting instructions!
18.2 588296000
Galvanised
Length: 190 - 341 cm
Observe all applicable safety regulations.
8.5
12.0
17.5
21.0
24.8
582306000
582307000
582308000
582309000
582310000
10.2
16.5
17.5
21.0
24.8
582311000
582312000
582313000
582314000
582315000
Aluminium
33.3 588297000
Galvanised
Length: 309 - 550 cm
Observe all applicable safety regulations.
Aluminium
10.5 582316000
Staxo 100-Stirngelnder
Galvanised
Length: 140 cm
Height: 152 cm
3.7 582768000
Universal-Lsewerkzeug
Galvanised
Length: 75.5 cm
76
999800302 - 06/2008
Component overview
[kg] Article n
Staxo 100 side railing 100
Staxo 100 side railing 150
Staxo 100 side railing 200
Staxo 100 side railing 250
Staxo 100 side railing 300
13.5
16.0
18.0
22.0
23.0
Staxo 100-Seitengelnder
582317000
582318000
582319000
582320000
582321000
[kg] Article n
Brace stirrup 8
2.7 582751000
Spannbgel 8
Galvanised
Width: 19 cm
Height: 46 cm
Width-across: 30 mm
Never weld or heat tie-rods - risk of
fracture!
Galvanised
Height: 152 cm
0.09 582521000
0.09 582522000
0.25 582528000
Handrail post 1.50m
Galvanised
Length: 15 cm
Packed in units of 100
Galvanised
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
4.0
682014000
682015000
682016000
682017000
682018000
682019000
682021000
682022000
682023000
682024000
682025000
682001000
Handrail clamp S
bergangsdrehkupplung 48/76mm
Galvanised
Width-across: 22 mm
11.5 580470000
Schutzgelnderzwinge S
Galvanised
Height: 123 - 171 cm
Galvanised
12.4 582754000
Gelnder 1,50m
1.9 582563000
17.7 584373000
Einschubgelnder T 1,80m
Galvanised
1.5 582560000
Drehkupplung 48mm
Galvanised
Width-across: 22 mm
1.2 682004000
Normalkupplung 48mm
Galvanised
Width-across: 22 mm
999800302 - 06/2008
Galvanised
Height: 7 cm
1.0 582546000
Zapfenkupplung 60mm
0.27 584375000
Gerstrohranschluss
1.9 586074000
Umsetzstab 15,0
Painted blue
Height: 57 cm
Max. load: 300 kg for single beams;
1000 kg for double beams in conjunction with retaining plate 15.0.
Never weld or heat tie-rods - risk of
fracture!
Follow the directions in the "Operating Instructions"!
77
Component overview
1.8 586073000
Jochplatte 15,0
[kg] Article n
Heavy duty wheel 15kN
Galvanised
Length: 17 cm
Width: 12 cm
Height: 11 cm
33.0 582575000
Schwerlastrad 15kN
Painted blue
Height: 41 cm
Max. load: 1500 kg
11.6 582795000
Galvanised
Painted blue
Perm. tensile force: 50 kN
Tie rod 15.0mm non-treated .....m
(art. no.: 581873000) not included
5.0 582558000
Zweirad-Transportroller
Painted blue
Width: 57 cm
Shifting carriage TG
168.0 582778000
Hubwagen TG
Galvanised
Length: 99 cm
Width: 152 cm
Height: 148 cm
Max. load: 1000 kg
Follow the directions in the "Operating Instructions"!
3.1 584371000
Spindellasche T
Galvanised
Width: 20 cm
Height: 25 cm
0.003 588180000
83.0 582797000
Umsetzgert TG fr Stapler
Winch 70
Galvanised
Length: 60 cm
Width: 113 cm
Height: 52 cm
Follow the directions in the "Operating Instructions"!
31.0 582779000
Zahnstangenwinde 70
Painted blue
Height: 126 cm
Max. load: 1000 kg
Follow the directions in the "Operating Instructions"!
Only wheel tableforms when the
toothed rack has been retracted!
Winch 125
63.8 582780000
Zahnstangenwinde 125
Painted blue
Height: 189 cm
Max. load: 1500 kg
Follow the directions in the "Operating Instructions"!
Only wheel tableforms when the
toothed rack has been retracted!
38.9 580007000
0.34 580201000
Verbindungsbolzen 10cm
Galvanised
Length: 14 cm
Packed in units of 100
14.1 582781000
Staxo/d2-Adapter
Painted blue
Length: 37 cm
Width: 36 cm
Height: 36 cm
Galvanised
Length: 13 cm
Packed in units of 250
34.5 582573000
Vollelastikrad
Painted blue
Height: 45 cm
Max. load: 1000 kg
78
0.06 580204000
Federvorstecker 6mm
64.6 582783000
Galvanised
Length: 180 cm
Width: 120 cm
Height: 29 cm
Max. load: 700 kg
Follow the directions in the "Operating Instructions"!
999800302 - 06/2008
Component overview
[kg] Article n
Doka stacking pallet 1.55x0.85m
Doka-Stapelpalette 1,55x0,85m
42.0 586151000
[kg] Article n
Outer railing 250
19.5 582672000
Auengelnder 250
Galvanised
Height: 77 cm
Max. load: 1100 kg
Follow the directions in the "Operating Instructions"!
Galvanised
Length: 255 cm
Height: 111 cm
6.3 582673000
Podestgelnder 250
Galvanised
Length: 160 cm
Height: 48 cm
33.6 586168000
Anklemm-Radsatz B
Painted blue
Max. load: 1100 kg
12.6 582674000
Einstiegsadapter 250
Galvanised
Height: 238 cm
75.0 583011000
Doka-Mehrwegcontainer 1,20x0,80m
Galvanised
Height: 78 cm
Max. load: 1500 kg
Follow the directions in the "Operating Instructions"!
3.7 583018000
5.5 583017000
Stair tower-set
39.5 582675000
Einstiegsgelnder 250
3.4 582680000
Ankerschuh fr Treppenturm
33.2 582670000
Alu-Treppenlauf 250
Aluminium
Length: 263 cm
Width: 80 cm
Height: 112 cm
Galvanised
Length: 22 cm
Width: 12 cm
Height: 22 cm
7.0 582671000
Innengelnder 250
Galvanised
Height: 155 cm
999800302 - 06/2008
79
>i>>
ivi`
&iiVVi>-V>}iVL
-"
iv1`>V*>]ii]>
/i\{{x]>\{{{{
>\"i>J`>V
ii\`>V
>
i>`
*}>
-i`i
> >
>>>
Vi`>
,>ii`->]n
>``
>
>-*
*
/iii\xx{{x
/iiv>\xx{{x
>\ >J`>V
>i>`/iV`
>iLVi]}i`>
/iii\x{n
/iiv>\x{nxx
>\i>`J`>V
>*}>
v>}i`>
>`>,i>]{,iV>`>>>
->>>>i-}i
*{x->
/iii\x
/iiv>\x
>\*}>J`>V
>-i}i
`B}i
-{xxx1``i>>
/iii\{xx
/iiv>\{xx
>\-i}iJ`>V
+>>
>+>>7
*" {
>]+>>
/iii\{{xn
/iiv>\{{xn
>\+>>J`>V
>>ii
->>i/V>i-
>>>i]<iV>
>`
/,{{iLi]V>i
/iii\{x
/iiv>\{n
>\/iJ`>V
->`>L>
1i`>L >i
>/iV}
v>`">
*"
i``>{
/iii\n
/iiv>\{nx
>\i``>J`>V
>v<
*" {
iLiii<i]L>
/iii\{nnn
/iiv>\{nnn
>\
>iJ`>V
-vV>
>-vV>
>i/ >V
*" x
xi]
>i/
/iii\xx
/iiv>\x{{x
>\-vV>J`>V
>1
/iV}i`
Vii>>]i>,>`
}Vii>
>`i]i]
{
/iii\{{{x
/iiv>\{{{
>1J`>V
->
1-
>>`>
>
>>`>`
x{{-ii-
>}> /
*
/iii\{{
/iiv>\{{n
>\
>>`>J`>V
>
>->}>
]`
n "9>>8,>`
->}>x
/iii\nx
/iiv>\nx
>\
>J`>V
>`
>>`"
-iix{
-i
/iii\xn{{
/iiv>\xn{{
>\>`J`>V
iiVi
>i>
>iV/iV}
}>>x
,xx*>
/iii\
/iiv>\{
>\i>J`>V
>
>>>-
->`>*V>i
iV>]
>
/iii\n
/iiv>\nx
>\>>J`>V
>
>>
v,>i/>`E
*" ->>
>
/iii\x{n{
/iiv>\x{n{
>\>J`>V
iL>
&iiVVi>
-V>}iVL
> >ViL>
-`iV->i] V
y
iiL>
/iii\x
/iiv>\x
>\iL>J`>V
>
> }ii}}>`i{
ni`>
/iii\{nn
/iiv>\{nn
>\ }iJ`>V
>iVi{
n->>`i>6i}>>``
/iii\{nxx
/iiv>\{nxx
>\
>>J`>V
/i
1i`}`
>1-]`
{>i,>`
ii] {
/iii\n
/iiv>\{x{
>\>J`>V
ii\`>>V
"iL`>i>`
iii>i\
}i>
>>
i}
i
}>>
>
>>
iV,iLV
i>
>
>Vi
i>
>i>>
}>
Vi>`
`>
>
>>
`>
>>>
i>
>>
>>
L>
iL}
>VV
iV
ii>`
i<i>>`
*>>>
*>`
,>>
,>
-ii}>
-iL>
-}>i
->>
-i>
-i>`
/>>
/>>`
/>
1>i
6i>