Escolar Documentos
Profissional Documentos
Cultura Documentos
Integration Guide
for Player Tracking and
Online Components
Location of Components, Mounting Areas and
Connectors Pinout
Rev. 1.2
June 2010
Copyright Notice:
2010, ATRONIC. All rights reserved.
No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval
system, or translated into any human or computer language, in any form or by any means, electronic,
mechanical, magnetic, manual, or otherwise, or disclosed to third parties without the express written
permission obtained from a properly authorized official of ATRONIC.
DISCLAIMER
ATRONIC makes no representation or warranties, express or implied, with respect to this publication,
or any product of ATRONIC, including but not limited to warranties of merchantability or fitness for any
particular purpose. ATRONIC reserves the right to make changes, enhancements, revisions and alterations of any kind to this publication or the product(s) it covers without obligation to notify any person,
institution or organization of such changes, enhancements, revisions and alterations.
TRADEMARKS
This document may contain trademarks of ATRONIC. All other brand and product names are trademarks
or registered trademarks of their respective companies.
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Available Mounting Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Player Tracking Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 SMIB Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Peripheral Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Accounting System Connectors Pinout . . . . . . . . . . . . . . . . 9
4. SAS Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. Manufacturing Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Generic Player Tracking Bracket . . . . . . . . . . . . . . . . . . . . . 13
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
1. Introduction
1. Introduction
1.1 About this Manual
Scope
1. This document is to inform your company of the upcomming release (May 2010) of the new ATRONIC OXYGEN cabinet, which will require a custom designed bracket to accomodate your player tracking components.
2. This document is intended to provide manufacturers of
player tracking and online equipment with the data required
to integrate and build
- custom designed player tracking brackets
- SMIB solutions to connect to the floor network
- the required cables and accessories.
Important: ATRONIC will not provide customized cables and/or accessories to connect the
equipment listed above. Manufacturers of player
tracking and online equipment are responsible to
provide such equipment. Exceptions require an explicit request including account of expenditures.
Target Audience
We address manufacturers of player tracking components,
player tracking brackets and other online system components.
Further we address service technicians involved in online system installations.
ATRONIC OXYGEN Cabinet
Nomenclature
OXYGEN is the name of the new cabinet featuring two 22
wide screen monitors.
sensys EP is the electronic platform used in the OXYGEN
cabinet.
diversity is the name of the new ATRONIC multi-game software available on OXYGEN/sensys EP.
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
Peripheral Board
SMIB Bracket
Player Tracking
Bracket
115/230V AC
Power Outlets
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
50
231,5
Available
Mounting
Area
81
100
for printer
Visible area
349
349
75
75
ca. 165
150
ca. 135
for printer
165
208
70
250
298
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
3. Peripheral Board
3. Peripheral Board
Online system components such as Smart Interface Bords (SMIB) and similar equipment have to be connected to the ATRONIC Peripheral Board.
The figure below shows the main connections to connect SAS based online equipment. The connection
intended for accounting systems is splitted into two connectors. It provides SAS channel 1 and the door
connectors.
SAS Channel 3
SAS Channel 2
SAS Channel 1
(+ Door Connectors)
Peripheral Board
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
3. Peripheral Board
14
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
+5V
+12V
COM 0 / RS232 RxD
COM 0 / RS232 TxD
Bill Door - Normally Close
Bill Door - Common
Bill Door - Normally Open
Drop Door - Normally Close
Drop Door - Common
Drop Door - Normally Open
Logic Door - Normally Close
Logic Door - Common
Logic Door - Normally Open
Ground
Recommended Connector:
Molex 22-01-3147, Crimp Terminal 08-52-0123
or Tyco 1-770602-4, Crimp Terminal 770666-1
Recommended Connector:
Molex 22-01-3127, Crimp Terminal 08-52-0123
or Tyco 1-770602-2, Crimp Terminal 770666-1
The connections for SAS channels 2 and 3 come as a D-Sub 9 male connector (serial connector).
SAS Channel 3
1
2
3
4
5
6
7
8
9
NC
COM 4 / RS232 RxD
COM 4 / RS232 TxD
+5V
Ground
NC
+12V
NC
NC
6
1
SAS Channel 2
1
2
3
4
5
6
7
8
9
6
1
NC
COM 1 / RS232 RxD
COM 1 / RS232 TxD
+5V
Ground
NC
+12V
NC
NC
Cable Lenght
Recommended cable length to connect player tracking components located on the inside of the
main door to the Peripheral Board is approximately 1,50 - 2,00 meters.
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
Enable/Disable a Channel:
Select the Enabled/Disabled field of a channel and touch
the Modify button to generally enable or disable a SAS
channel.
EGM Address:
Configures the SAS machine address on this SAS channel.
Control:
Allocate the control polls to one of the channels. Control
polls can not be disabled on all channels.
AFT Transfers:
Allocate the polls for AFT transfers to one of the channels
or disable them on all channels.
Note: To disable AFT in general, adjust the AFT Transfers setting to disabled on all enabled channels.
Legacy Bonus:
Allocate the legacy bonusing polls to one of the channels.
Ticketing:
Allocate the polls and exceptions for ticketing to one of
the channels or disable them on all channels.
Ticket Reporting:
This entry allows to send ticket reporting polls on additional channels for reporting purposes.
Note: In most case the actual SAS machine address is provided by a connected Smart Interface Board (SMIB). In this
case set the EGM Address to 1.
- continued on next page OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
10
Handpay Reporting:
This entry defines the handpay buffer handling.
Secure (default):
If the handpay buffer is full, the machine locks up until
the pending handpay polls are read by the accounting
system.
Overwrite:
If the handpay buffer is full, the oldest entries will be
overwritten and the machine remains playable. This
handling is intended for EGMs connected to an accounting system that does not read handpay polls and
for EGMs not connected to an accounting system at all.
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
11
- blank page OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
12
5. Manufacturing Drawings
100
92 (2x)
90 (2x)
50
8 (2x)
3,5 (2x)
0
13,5 (2x)
226,5
231,5
236,5
4,5
6,5
Notes:
visible side
415,5 (2x)
423,5
441,8 (2x)
456
463
11,5 (2x)
24,5 (2x)
91,5 (2x)
85 (2x)
15 (2x)
8,5 (2x)
0
13
OXYGEN Cabinet - Integration Guide for Player Tracking and Online Components
0
6,3
7
21,3 (2x)
39,5
47,5 (2x)
(4x
5(
5x)