Você está na página 1de 40

The diode circuit which is used to clip off portions of

Page 2
Electrical-jan-2013 The diode circuit which is used to clip off portions of
Page 2
Electrical-jan-2013 pradeep

The voltage induced across a certain coil is 150 mV. A 100


?? resistor is connected
to the coil terminals. Calculate the induced current.
Variable Answer Units Correct to
I mA 1 decimal
1)
in a series circuit,which value remajn unchanged throughout and why?
a. voltage
b.current
c.resistance
d.inductance( current usgc in first 500 questions)
For leading power factor circuits, which of the following can be used?
A.Shunt Capacitors only
B.Shunt Reactors only
C.Either Shunt Capacitors or Shunt Reactors
D.Neither Shunt Capacitors Nor Shunt Reactors
Series RLC voltage or impedence totals must be calculate by ________vectors
If an intrinsic semiconductor is doped with a very small amount of boron then the
extrinsic semiconductor set formed ,the no. of electrons and holes will
A.both dec
B.increase and decrease
C.Both increase
D.Decrease and increase
.which of the following capacitor is having highest di electric constant
A.air gap
B.glass
C. paper
D.polyster
Arrange the following in Increasing Order of their Doping Strength.
a)collector, base, emitter
b)emitter, base, collector
For leading power factor circuits, which of the following can be used?
A. Shunt Capacitors only
B. Shunt Reactors only

C. Either Shunt Capacitors or Shunt Reactors


D. Neither Shunt Capacitors Nor Shunt Reactors

The armature resistance of a 200 V d.c. machine has 0.5 ohm. If the full load armature current is 50 A,
what will be the induced e.m.f. when, the machine acts as (i) generator (ii) motor will be
C. 225 V, 175 C
A. 230 V, 170 V
B. 210 v, 190 v
D. 202.5 V, 197.5 V
Ans is C.....
When acts like GEN, then
E=V+IR= 200+(50*0.5)=225....
When acts like motor, then
E=V-IR=200-(50*0.5)=175....
So ans is C... 225,175....

Electrical-jan-2013
*Question 1
Which of the listed precautions should be taken when
cleaning the internals of a
motor with compressed air?
A. Open the machine on both ends so as to allow the air and
dust to escape.
B. Be certain that the circuit breaker is opened and tagged
on the feeder panel.
C. Be certain that the air is clean and as dry as possible.
D. Ensure that the fuse in the motor is removed.
*Question 2
What is the value of Z in a series ac circuit where XL = 9
ohms, XC = 5 ohms and R =
8 ohms? Your answer should be correct to one decimal.
Variable Answer Units Correct to
Z ohms 1 decimal
Question 3
What type of rotor is used in split-phase motors?
A. Drum
B. Salient pole
C. Squirrel-cage
D. Wound-rotor
*Question 4
The voltage induced across a certain coil is 150 mV. A 100
?? resistor is connected
to the coil terminals. Calculate the induced current.
Variable Answer Units Correct to
I mA 1 decimal
Question 5
Where a thermal-acting breaker is required to be used in an
area of unusually high,
low, or constantly fluctuating temperatures, an ambient
compensating element must be
Page 3
NEW
used. This element consists of a
A. Cylindrical spring on the contact arm.
B. Conical spring on the contact arm.
Page 1
Electrical-jan-2013 pradeep
C. Second bimetal element.
D. Second electromagnet.
*Question 6
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?

A. Room temperature.
B. Liquid Line temperature.
C. Recharge temperature.
D. Solenoid valve operation.
*Question 7
A poly-phase motor driving an engine room pump fails to
start. When trying to
identify the cause of failure, which of the following steps
are applicable?
A. Ensure that the isolator is open.
B. Make sure that there is no restriction preventing
movement of pump/motor.
C. Check whether the overload relay has tripped.
D. Check whether battery is fully charged.
*Question 8
The induced voltage across a stationary conductor in a
steady magnetic field is
zero.
True
False
*Question 9
A poly-phase motor driving an engine room pump fails to
start. When trying to
identify the cause of failure, which of the following steps
are applicable?
A. Visually examine motor for open circuit faults.
B. Visually examine starter for open circuit faults.
C. Reverse the direction of electrical supply to check if it
works.
D. Perform the infinite resistance test.
*Question 10
The diode circuit which is used to clip off portions of
Page 2
Electrical-jan-2013 pradeep
signal voltages is called a
(1)________.
1)
*Question 11
Four 6F capacitors are connected in parallel. Calculate the
effective capacitance.
Variable Answer Units Correct to
C Farads 0 decimal
Question 12
Time delayed or delayed action-type fuses are designed to
A. prevent grounds in branch circuits
B. prevent opens in motor circuits
C. permit momentary overloads without melting
*Question 13
The opposition to the establishment of magnetic lines of
force in a magnetic circuit
is called the circuit's
A. resistance
B. reluctance
C. impedance
D. inductance
Question 14
A molded-case breaker provides protection against
short-circuits by usinga/an
A. Shading coil.

B. Arc quencher.
C. Electromagnet.
D. Holding coil.
Question 15
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?
A. Sea water temperature and pressure.
B. Condensing temperature
C. Refrigerant leakage
D. Evaporating temperature
Question 16
Which of the listed conditions is an advantage of a PN diode
Page 3
Electrical-jan-2013 pradeep
over a vacuum diode?
A. Longer life.
B. No warm up time.
C. Less delicate.
D. All of the above.
*Question 17
The apparent power in a purely inductive circuit is also
known as
A. true power
B. lead power
C. induced power
D. reactive power
*Question 18
A 45 ohm resistor is connected to a 3V battery. Calculate
the power dissipation of
the resistor.
Variable Answer Units Correct to
p milliwatts 0 decimal
Question 19
The winding resistance of a coil can be increased by _______
the number of turns or
using a ______ wire.
Page 13
NEW
A. increasing, thicker
B. decreasing, thicker
C. increasing, thinner
D. decreasing, thinner
Question 20
The current in a semiconductor is produced by:
A. Electrons
B. Neutrons
C. Protons
D. Holes
Question 21
Which of the listed devices may be installed on a large
turbo-electric alternating
current propulsion generator?
A. Temperature detector coils inserted in the stator slots
Page 4
Electrical-jan-2013 pradeep
for measuring stator
temperature.
B. A CO2 fire extinguishing system.

C. Electric space heaters to prevent condensation of


moisture.
D. All of the above.
*Question 22
Open-loop transfer function of a system having one zero with
positive real values is
called (1)________ phase function.
1)
*Question 23
Which of the following capacitor types has a di-electric
constant of 1.000?
A. Air Gap
B. Vacuum
C. Water
D. Electrolytics
*Question 24
Which of the following statements represents an application
of a silicon controlled
rectifier?
A. To provide DC power for a main propulsion motor.
B. For use as a voltage reference diode.
C. For sensing flame in an automated burner.
D. To eliminate power supply hum.
Question 25
Tightly knit metal braid wire can be used with a printed
circuit board when
A. Conductor flexibility is required
B. De-soldering components in the circuit
C. Electrically produced magnetic fluxes would cause
inaccuracies in adjacent
components
D. Reactance in the circuit must be kept to a minimum
Page 5
1.A poly-phase motor driving an engine room pump fails to start. When trying to identify
the cause of failure, which of the following steps are applicable?
A.Visually examine motor for open circuit faults.
B.Visually examine starter for open circuit faults.
C.Reverse the direction of electrical supply to check if it works.
D.Perform the infinite resistance test.
2.Tightly knit metal braid wire can be used with a printed circuit board when
A.Conductor flexibility is required
B.De-soldering components in the circuit
C.Electrically produced magnetic fluxes would cause inaccuracies in adjacent
components
D.Reactance in the circuit must be kept to a minimum
3.Which of the following statements represents an application of a silicon controlled
rectifier?
A.To provide DC power for a main propulsion motor.
B.For use as a voltage reference diode.
C.For sensing flame in an automated burner.
D.To eliminate power supply hum.
4.When paralleling an AC generator with live bus bars, which of the following precautions
are applicable?
A.Generator frequency should be slightly lower than bus bar frequency

B.Generator frequency should be slightly higher than bus bar frequency


C.Generator voltage should be in phase with bus bar voltage
D.Generator voltage should be out of phase with bus bar voltage
5.A certain appliance uses 750 W. If it is allowed to run continuously for 15 days, how
many kilowatt-hours of energy does it consume?
6.With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.Room temperature.
B.Liquid Line temperature.
C.Recharge temperature.
D.Solenoid valve operation.
8.With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.Sea water temperature and pressure.
B.Condensing temperature
C.Refrigerant leakage
D.Evaporating temperature
9.The induced voltage across a stationary conductor in a steady magnetic field is zero.
True
False
10.For leading power factor circuits, which of the following can be used?
A.Shunt Capacitors only
B.Shunt Reactors only
C.Either Shunt Capacitors or Shunt Reactors
D.Neither Shunt Capacitors Nor Shunt Reactors
11.A molded-case breaker provides protection against short-circuits by usinga/an
A.Shading coil.
B.Arc quencher.
c.Electromagnet.
D.Holding coil.
12.Fuses placed in series with a thermal trip = - type circuit breaker are used for
A.Time-delay protection
B.Short-circuit protection
C.Short duration surge protection
D.Sustained overload protection
13.Which of the listed precautions should be taken when cleaning the internals of a
motor with compressed air?
A.Open the machine on both ends so as to allow the air and dust to escape.
B.Be certain that the circuit breaker is opened and tagged on the feeder panel.
C.Be certain that the air is clean and as dry as possible.
D.Ensure that the fuse in the motor is removed.
14.A fuse that blows often should be replaced only with a fuse of
A.the recommended current and voltage rating
B.higher current and voltage rating
C.higher current and lower voltage rating
D.lower current and higher voltage rating
15.Open-loop transfer function of a system having one zero with positive real values is
called (1)________

16.Where a thermal-acting breaker is required to be used in an area of unusually high,


low, or constantly fluctuating temperatures, an ambient compensating element must be
used. This element consists of a
A.Cylindrical spring on the contact arm.
B.Conical spring on the contact arm.
C.Second bimetal element.
D.Second electromagnet.
17.Brushless generators are designed to operate without the use of
A.brushes
B.sliprings
C.commutators
D.all of the above
18.What is the magnetomotive force in a 75-turn coil of wire when there are 4 A of
current through it?
19.In what range of voltages is the transistor in the linear region of its operation?
A.0 < VCE < 0.7 V
B.0.7 < VCE < 1.4 V
C.0.7 < VCE < VCE(max)
D.0 < VCE < VCE(max)
20.The current in a semiconductor is produced by:
A.Electrons
B.Neutrons
C.Protons
D.Holes
21.AC circuits possess characteristics of resistance, inductance, and capacitance.The
capacitive reactance of acircuit is expressed in
A.ohms
B.mhos
C.henrys
D.farads
22.The greatest detrimental effect on idle electrical equipment, such as cargo pump
motors,is the
A.Loss of residualmagnetism.
B.Absorption of moisture in the insulation.
C.Insulation varnish flaking.
D.Dirt collecting on the windings.
23.If it takes 35 J of energy to move a charge of 6 C from one point to another, what is
the voltage between the two points? Your answer should be correct to two decimals.
24.The basic measuring unit of inductance is the
A.coulomb
B.ohm
C.farad
D.henry

*Question 1
Which of the listed precautions should be taken when
cleaning the internals of a
motor with compressed air?
A. Open the machine on both ends so as to allow the air and

dust to escape.
B. Be certain that the circuit breaker is opened and tagged
on the feeder panel.
C. Be certain that the air is clean and as dry as possible.
D. Ensure that the fuse in the motor is removed.
*Question 2
What is the value of Z in a series ac circuit where XL = 9
ohms, XC = 5 ohms and R =
8 ohms? Your answer should be correct to one decimal.
Variable Answer Units Correct to
Z ohms 1 decimal
Question 3
What type of rotor is used in split-phase motors?
A. Drum
B. Salient pole
C. Squirrel-cage
D. Wound-rotor
*Question 4
The voltage induced across a certain coil is 150 mV. A 100
?? resistor is connected
to the coil terminals. Calculate the induced current.
Variable Answer Units Correct to
I mA 1 decimal
Question 5
Where a thermal-acting breaker is required to be used in an
area of unusually high,
low, or constantly fluctuating temperatures, an ambient
compensating element must be
Page 3
NEW
used. This element consists of a
A. Cylindrical spring on the contact arm.
B. Conical spring on the contact arm.
Page 1
Electrical-jan-2013 pradeep
C. Second bimetal element.
D. Second electromagnet.
*Question 6
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?
A. Room temperature.
B. Liquid Line temperature.
C. Recharge temperature.
D. Solenoid valve operation.
*Question 7
A poly-phase motor driving an engine room pump fails to

start. When trying to


identify the cause of failure, which of the following steps
are applicable?
A. Ensure that the isolator is open.
B. Make sure that there is no restriction preventing
movement of pump/motor.
C. Check whether the overload relay has tripped.
D. Check whether battery is fully charged.
*Question 8
The induced voltage across a stationary conductor in a
steady magnetic field is
zero.
True
False
*Question 9
A poly-phase motor driving an engine room pump fails to
start. When trying to
identify the cause of failure, which of the following steps
are applicable?
A. Visually examine motor for open circuit faults.
B. Visually examine starter for open circuit faults.
C. Reverse the direction of electrical supply to check if it
works.
D. Perform the infinite resistance test.
*Question 10
The diode circuit which is used to clip off portions of
Page 2
Electrical-jan-2013 pradeep
signal voltages is called a
(1)________.
1)
*Question 11
Four 6F capacitors are connected in parallel. Calculate the
effective capacitance.
Variable Answer Units Correct to
C Farads 0 decimal
Question 12
Time delayed or delayed action-type fuses are designed to
A. prevent grounds in branch circuits
B. prevent opens in motor circuits
C. permit momentary overloads without melting
*Question 13
The opposition to the establishment of magnetic lines of
force in a magnetic circuit
is called the circuit's
A. resistance
B. reluctance

C. impedance
D. inductance
Question 14
A molded-case breaker provides protection against
short-circuits by usinga/an
A. Shading coil.
B. Arc quencher.
C. Electromagnet.
D. Holding coil.
Question 15
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?
A. Sea water temperature and pressure.
B. Condensing temperature
C. Refrigerant leakage
D. Evaporating temperature
Question 16
Which of the listed conditions is an advantage of a PN diode
Page 3
Electrical-jan-2013 pradeep
over a vacuum diode?
A. Longer life.
B. No warm up time.
C. Less delicate.
D. All of the above.
*Question 17
The apparent power in a purely inductive circuit is also
known as
A. true power
B. lead power
C. induced power
D. reactive power
*Question 18
A 45 ohm resistor is connected to a 3V battery. Calculate
the power dissipation of
the resistor.
Variable Answer Units Correct to
p milliwatts 0 decimal
Question 19
The winding resistance of a coil can be increased by _______
the number of turns or
using a ______ wire.
Page 13
NEW
A. increasing, thicker
B. decreasing, thicker

C. increasing, thinner
D. decreasing, thinner
Question 20
The current in a semiconductor is produced by:
A. Electrons
B. Neutrons
C. Protons
D. Holes
Question 21
Which of the listed devices may be installed on a large
turbo-electric alternating
current propulsion generator?
A. Temperature detector coils inserted in the stator slots
Page 4
Electrical-jan-2013 pradeep
for measuring stator
temperature.
B. A CO2 fire extinguishing system.
C. Electric space heaters to prevent condensation of
moisture.
D. All of the above.
*Question 22
Open-loop transfer function of a system having one zero with
positive real values is
called (1)________ phase function.
1)
*Question 23
Which of the following capacitor types has a di-electric
constant of 1.000?
A. Air Gap
B. Vacuum
C. Water
D. Electrolytics
*Question 24
Which of the following statements represents an application
of a silicon controlled
rectifier?
A. To provide DC power for a main propulsion motor.
B. For use as a voltage reference diode.
C. For sensing flame in an automated burner.
D. To eliminate power supply hum.
Question 25
Tightly knit metal braid wire can be used with a printed
circuit board when
A. Conductor flexibility is required
B. De-soldering components in the circuit
C. Electrically produced magnetic fluxes would cause

inaccuracies in adjacent
components
D. Reactance in the circuit must be kept to a minimum
Page 5
Like
Like Follow Post Wednesday at 11:23am

5 people like this.

50 of 61
View previous comments

Ailen Dsouza 13-b


Wednesday at 11:28am Like

Ailen Dsouza 12-b


Wednesday at 11:28am Like

Ailen Dsouza 11-24


Wednesday at 11:28am Like 2

Ailen Dsouza 10 - clippers


Wednesday at 11:29am Like

Ailen Dsouza 9 - aand b as per sawant sir munbai

Wednesday at 11:29am Like

Ailen Dsouza 8-true


Wednesday at 11:29am Like

Ailen Dsouza 7- a,b and c


Wednesday at 11:30am Like

Ailen Dsouza 5- c
Wednesday at 11:30am Like

Ailen Dsouza question no 2,3, 4, 6,15,18 any idea friends@Wasim Hussain N,


Wednesday at 11:33am Like

Ailen Dsouza question no 2,3, 4, 6,15,18 any idea friends@Rajat Singh, ,@Sudipta Kundu, Prasad Pravin
Parab,@Manjeet Pratap,@Ankur Ankur Chauhan,@
Wednesday at 11:45am Like

Ailen Dsouza ans 5 is 8.91????????????????????any idea guys


Wednesday at 11:58am Like


Manjeet Pratap for2: Z= UNDER ROOT( R^2 + (XC -XL)^2)... ANS 8.9
Wednesday at 12:05pm Like 3

Manjeet Pratap 3: c..... hall page 112


Wednesday at 12:05pm Like 2

Manjeet Pratap 4: 1.5 mA .... use formulae V=IR


Wednesday at 12:06pm Like 2

Manjeet Pratap 6:a,b n d


Wednesday at 12:07pm Like 1

Rajat Singh good work Ailen Dsouza and thx Manjeet Pratap
Wednesday at 12:09pm Like

Manjeet Pratap 18: 0.2 ..... P= V^2/R


Wednesday at 12:09pm Like 2

Manjeet Pratap Ailen Dsouza if u find feb. paper pls post it....

Wednesday at 12:11pm Like 2

Pradeep Msc Shippinghttps://www.facebook.com/groups/208959922570415/


Wednesday at 12:29pm Like 2

Nayeemuddin Khan 25.b


Wednesday at 12:36pm Like 1

Fecil M Francis 15.a & c


Wednesday at 6:30pm Like 1

Nayeemuddin Khan 15.a and c


Wednesday at 7:03pm Like

Nayeemuddin Khan 10.limiters or clippers


Wednesday at 7:47pm Like

Nayeemuddin Khan Ailen Dsouza 12.c (uscg 157)


Wednesday at 7:55pm Like

Ailen Dsouza yes ur rite friend


Wednesday at 8:11pm via mobile Like

Nayeemuddin Khan Ailen Dsouza do you have previous electrical online questions
Wednesday at 8:14pm Like

Nayeemuddin Khan Ailen Dsouza 25.b


Wednesday at 8:15pm Like

Rajat Singh Ailen Dsouza bhai 12 b aapko kaha se mila?


Wednesday at 8:21pm Like

Rajat Singh Nayeemuddin Khan sir limiters ya clippers?


Wednesday at 8:27pm Like

Nayeemuddin Khan both are right but dont know which is the correct ans in there key
Wednesday at 8:29pm Like

Mohit Bhatia limiter is also known as clipper


Yesterday at 5:49am Like


Mohit Bhatia 23 a
Yesterday at 5:52am Like

Ailen Dsouza clipper is what they want exam as one of friend cleared writing it
Yesterday at 5:52am via mobile Like

Nayeemuddin Khan Ailen Dsouza ok


Yesterday at 8:00am via mobile Like

Nayeemuddin Khan Ailen Dsouza plz post general and naval arc online question and answers
Yesterday at 8:00am via mobile Like

Nayeemuddin Khan Mohit Bhatia ru sure 23 a


Yesterday at 8:02am via mobile Like

Kshitij Bajaj Hanoz Daruwalla..Jan paper


Yesterday at 8:06am via mobile Like

Ailen Dsouza 23 b

Yesterday at 8:12am via mobile Like

Pankaj Dogra frens 23 answer is a plzz do check di-electric chart


Yesterday at 10:58am Like

Manjeet Pratap 23:a ...http://en.wikipedia.org/wiki/Dielectric_constant


Yesterday at 11:01am Like

Ailen Dsouza vacum is 1.00000000000 and air gap is 100058


Yesterday at 11:03am Like 1

Ailen Dsouza 23 B Pankaj Dogra,@Manjeet Pratap


Yesterday at 11:05am Like

Pankaj Dogra thanks buddy !!


Yesterday at 11:06am Like

Pankaj Dogra http://www.engineeringtoolbox.com/liquid-dielectric-constants-d_1263.html


Yesterday at 11:07am Like

Yesu Vetha Blessing 15-a,b,d


23 hours ago Like

Prasad Pravin Parab 21?????


10 hours ago Like

Manjeet Pratap 21: d


5 hours ago Like

Nayeemuddin Khan Material Dielectric Constant


Vacuum
1
Glass
5-10...See More
3 hours ago Like 1

Hemanth Nagaraj Ailen Dsouza ru sure 19.c...???


3 hours ago Like

Muniyandi Sivaprakasam 23.b


3 hours ago via mobile Like

Preferential tripping of electrical machineries prevents


A. Overloading of generators
B. Black out in engine room

C. Allows starting of large machineries


D. None of the above
Four 6F capacitors are connected in parallel. Calculate the
effective capacitance.
Variable Answer Units Correct to
C Farads 0 decimal

14. Calculate the Velocity of the conductor (up to 0 decimal places), if terminal voltage is
2.2 V/m and the magnetic field strength is 0.2 T.

1.The type of the system whose transfer function is given by


G(S) =(s2+3)/(s5+s4+s3+3s2+2s) is:
Variable Answer Units Correct to
G
NA 0 decimal
2.A certain appliance uses 750 W. If it is allowed to run continuously for 15 days,
how many kilowatt-hours of energy does it consume?
Variable Answer Units Correct to
KwH
KwH 0 decimal
3.Open-loop transfer function of a system having one zero with positive real
values is called (1)________ phase function.(one fill in blank)
4.If it takes 35 J of energy to move a charge of 6 C from one point to another,
what is the voltage between the two points? Your answer should be correct to two
decimals.
Variable Answer Units Correct to
V
volts 2 decimal
5.A semiconductor is damaged by a strong current, because of (1)________
(2)________ (3)________
1)
2)
3)
(Three blanks to be filled)
6. current in semi conductors is by _____________ and _______________( two blanks
to be filled)
7. electrons and protons of the same momentum enter normally into a uniform
magnetic field of flux density B. mass of the electron is me (m suffix e) and mass
of the proton is mp (m suffix p).if re (r suffix e) and rp (r suffix p) represents the
radii of the path of the electrons and the protons respectively. calculate the ratio
re/rp. your answer should be correct to 2 decimals...
8. In a P-Type Semiconductor, the majority current Carriers are ___________.
9. In a Control Loop System, having Zero(0) Positive Real Values are
called____________.

10. The material which has a less no of free electrons called..............


11. Vgs and Id approximately zero....this is called _________________ voltage
12.A 40 cm wire a current of 20 amps is placed in a uniform magnetic field of
0.6.the wire make an angle of 30 degree.cal the magnitude of force on wire
13.The diode circuit which is used to clip off portions of signal voltages is called a
(1)________.(one blank to be filled)
14.velocity & impedence of RLC circuit was found by ---------------vector.
15.Calculate the avg value of a 12v peak sine wave over one complete cycle.
16.what happens to the amount of energy stored in the electromagnetic field
when the current through an inductor is cut in half___________
17.what happens to the strength of electro magnetic field when current passing
through an inductor is halfed__________a.1/4
b.1/2
c.2
d.4
18. a sine wave with rms value of 100v is riding on a dc level of 50v.calculate the
maximum value of the resulting wave form ...
19.In what range of voltages is the transistor in the linear region of its operation?
A.
0 < VCE < 0.7 V
B.
0.7 < VCE < 1.4 V
C.
0.7 < VCE < VCE(max)
D.
0 < VCE < VCE(max)
20.
What is the magnetomotive force in a 75-turn coil of wire when there are 4 A of
current through it?
Variable Answer Units Correct to
MMF
At 0 decimal
21. the appereant powerin inductive circuit
a truepower b lead c inductive d reactive
( choose correct alternative from given 4 options)
22. MUTIPLE CHOICE QUESTION
A poly-phase motor driving an engine room pump fails to start. When trying to
identify the cause of failure, which of the following steps are applicable?
A.

Visually examine motor for open circuit faults.


B.
Visually examine starter for open circuit faults.
C.
Reverse the direction of electrical supply to check if it works.
D.
Perform the infinite resistance test.
23.MUTIPLE CHOICE QUESTION
When paralleling an AC generator with live bus bars, which of the following
precautions are applicable?
A.
Generator frequency should be slightly lower than bus bar frequency
B.
Generator frequency should be slightly higher than bus bar frequency
C.
Generator voltage should be in phase with bus bar voltage
D.
Generator voltage should be out of phase with bus bar voltage
24.MULTIPLE CHOICE
With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.
Room temperature.
B.
Liquid Line temperature.
C.
Recharge temperature.
D.
Solenoid valve operation.
25. MULTIPLE CHOICE
With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.
Sea water temperature and pressure.
B.
Condensing temperature
C.
Refrigerant leakage
D.
Evaporating temperature

26.The induced voltage across a stationary conductor in a steady magnetic field


is zero.
True
False
27.For leading power factor circuits, which of the following can be used?
A.
Shunt Capacitors only
B.
Shunt Reactors only
C.
Either Shunt Capacitors or Shunt Reactors
D.
Neither Shunt Capacitors Nor Shunt Reactors
28.A molded-case breaker provides protection against short-circuits by usinga/an
A.
Shading coil.
B.
Arc quencher.
C.
Electromagnet.
D.
Holding coil.
29.Fuses placed in series with a thermal trip = - type circuit breaker are used for
A.
Time-delay protection
B.
Short-circuit protection
C.
Short duration surge protection
D.
Sustained overload protection
30.MULTIPLE CHOICE
Which of the listed precautions should be taken when cleaning the internals of a
motor with compressed air?
A.
Open the machine on both ends so as to allow the air and dust to escape.
B.
Be certain that the circuit breaker is opened and tagged on the feeder panel.
C.

Be certain that the air is clean and as dry as possible.


D.
Ensure that the fuse in the motor is removed.
31.SINGLE CHOICE ONLY
A fuse that blows often should be replaced only with a fuse of
A.
the recommended current and voltage rating
B.
higher current and voltage rating
C.
higher current and lower voltage rating
D.
lower current and higher voltage rating
32.The greatest detrimental effect on idle electrical equipment, such as cargo
pump motors,is the
A.
Loss of residualmagnetism.
B.
Absorption of moisture in the insulation.
C.
Insulation varnish flaking.
D.
Dirt collecting on the windings

two inductances are in series( 3 hen and 5 hen)..mutual inductance of 2 hen..


total effective inductance??
L(eff)=L1+L2+2M

A 40 cm wire current of 20 amp is placed in a uniform magnetic field of 0.6 the


wire make an angle of 30 degree cal the magnitude of force on wire F=B I L sin 30
ans(2.4N)

5.To prevent electric shock during electric arc welding


A.Wear dry clothes
B.Wear insulated shoes
C.Keep first aid equipment ready
D.None of the above
The diode circuit which is used to clip off portions of signal voltages is called a
(1)________
16.what happens to the amount of energy stored in the electromagnetic field
when the current through an inductor is cut in half___________
17.what happens to the strength of electro magnetic field when current passing
through an inductor is halfed__________-

a.1/4
b.1/2
c.2
d.4
14.velocity & impedence of RLC circuit was found by ---------------vector.
1.The type of the system whose transfer function is given by
G(S) =(s2+3)/(s5+s4+s3+3s2+2s) is:
Variable Answer Units Correct to
G
NA 0 decimal
2.A certain appliance uses 750 W. If it is allowed to run continuously for 15 days,
how many kilowatt-hours of energy does it consume?
Variable Answer Units Correct to
KwH
KwH 0 decimal

3.Open-loop transfer function of a system having one zero with positive real
values is called (1)________ phase function.(one fill in blank)
4.If it takes 35 J of energy to move a charge of 6 C from one point to another,
what is the voltage between the two points? Your answer should be correct to two
decimals.
Variable Answer Units Correct to
V
volts 2 decimal
5.A semiconductor is damaged by a strong current, because of (1)________
(2)________ (3)________
1)
2)
3)
(Three blanks to be filled)
6. current in semi conductors is by _____________ and _______________( two blanks
to be filled)
7. Calculate the frequency of the motor ( up to 0 decimal places),, if the speed if
400 Rps and number of Poles is 2.
8. In a P-Type Semiconductor, the majority current Carriers are ___________.
9. In a Control Loop System, having Zero(0) Positive Real Values are
called____________.

10. The material which has a less no of free electrons called..............


11. Vgs and Id approximately zero....this is called _________________ voltage
12.A 40 cm wire a current of 20 amps is placed in a uniform magnetic field of
0.6.the wire make an angle of 30 degree.cal the magnitude of force on wire
13.The diode circuit which is used to clip off portions of signal voltages is called a
(1)________.(one blank to be filled)
14.velocity & impedence of RLC circuit was found by ---------------vector.
15.Calculate the avg value of a 12v peak sine wave over one complete cycle.
16.what happens to the amount of energy stored in the electromagnetic field
when the current through an inductor is cut in half___________
17.what happens to the strength of electro magnetic field when current passing
through an inductor is halfed__________a.1/4
b.1/2
c.2
d.4
18. a sine wave with rms value of 100v is riding on a dc level of 50v.calculate the
maximum value of the resulting wave form ...
19.In what range of voltages is the transistor in the linear region of its operation?
A.
0 < VCE < 0.7 V
B.
0.7 < VCE < 1.4 V
C.
0.7 < VCE < VCE(max)
D.
0 < VCE < VCE(max)

20.
What is the magnetomotive force in a 75-turn coil of wire when there are 4 A of
current through it?
Variable Answer Units Correct to
MMF
At 0 decimal

21. the appereant powerin inductive circuit


a truepower b lead c inductive d reactive
( choose correct alternative from given 4 options)
what happens to the amount of energy stored in the electromagnetic field when
the current through an inductor is cut in half___________

5.A semiconductor is damaged by a strong current, because of (1)________


(2)________ (3)________
the appereant powerin inductive circuit
a truepower
b lead
c inductive
d reactive
what happens to the strength of electro magnetic field when current passing
through an inductor is halfed__________a.1/4
b.1/2
c.2
d.4
Vgs and Id approximately zero....this is called _________________ voltage(SEMI
CONDUCTOR)
In a Control Loop System, having Zero(0) Positive Real Values are
called____________.(PHASE FUNCTION)
1.The type of the system whose transfer function is given by
G(S) =(s2+3)/(s5+s4+s3+3s2+2s) is:
Variable Answer Units Correct to
G
NA 0 decimal
2.A certain appliance uses 750 W. If it is allowed to run continuously for 15 days, how
many kilowatt-hours of energy does it consume?
Variable Answer Units Correct to
KwH
KwH 0 decimal
3.Open-loop transfer function of a system having one zero with positive real values is
called (1)________ phase function.(one fill in blank)
4.If it takes 35 J of energy to move a charge of 6 C from one point to another, what is the
voltage between the two points? Your answer should be correct to two decimals.
Variable Answer Units Correct to
V
volts 2 decimal
5.A semiconductor is damaged by a strong current, because of (1)________ (2)________
(3)________
1)
2)
3)
(Three blanks to be filled)

6. current in semi conductors is by _____________ and _______________( two blanks to be


filled)
7. electrons and protons of the same momentum enter normally into a uniform magnetic
field of flux density B. mass of the electron is me (m suffix e) and mass of the proton is
mp (m suffix p).if re (r suffix e) and rp (r suffix p) represents the radii of the path of the
electrons and the protons respectively. calculate the ratio re/rp. your answer should be
correct to 2 decimals...
8. In a P-Type Semiconductor, the majority current Carriers are ___________.
9. In a Control Loop System, having Zero(0) Positive Real Values are called____________.
10. The material which has a less no of free electrons called..............
11. Vgs and Id approximately zero....this is called _________________ voltage
12.A 40 cm wire a current of 20 amps is placed in a uniform magnetic field of 0.6.the wire
make an angle of 30 degree.cal the magnitude of force on wire
13.The diode circuit which is used to clip off portions of signal voltages is called a
(1)________.(one blank to be filled)
14.velocity & impedence of RLC circuit was found by ---------------vector.
15.Calculate the avg value of a 12v peak sine wave over one complete cycle.
16.what happens to the amount of energy stored in the electromagnetic field when the
current through an inductor is cut in half___________
17.what happens to the strength of electro magnetic field when current passing through
an inductor is halfed__________a.1/4
b.1/2
c.2
d.4
18. a sine wave with rms value of 100v is riding on a dc level of 50v.calculate the
maximum value of the resulting wave form ...
19.In what range of voltages is the transistor in the linear region of its operation?
A.
0 < VCE < 0.7 V
B.
0.7 < VCE < 1.4 V
C.
0.7 < VCE < VCE(max)
D.
0 < VCE < VCE(max)

20.
What is the magnetomotive force in a 75-turn coil of wire when there are 4 A of current

through it?
Variable Answer Units Correct to
MMF
At 0 decimal

21. the appereant powerin inductive circuit


a truepower b lead c inductive d reactive
( choose correct alternative from given 4 options)
22. MUTIPLE CHOICE QUESTION
A poly-phase motor driving an engine room pump fails to start. When trying to identify
the cause of failure, which of the following steps are applicable?
A.
Visually examine motor for open circuit faults.
B.
Visually examine starter for open circuit faults.
C.
Reverse the direction of electrical supply to check if it works.
D.
Perform the infinite resistance test.
23.MUTIPLE CHOICE QUESTION
When paralleling an AC generator with live bus bars, which of the following precautions
are applicable?
A.
Generator frequency should be slightly lower than bus bar frequency
B.
Generator frequency should be slightly higher than bus bar frequency
C.
Generator voltage should be in phase with bus bar voltage
D.
Generator voltage should be out of phase with bus bar voltage
24.MULTIPLE CHOICE
With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.
Room temperature.
B.
Liquid Line temperature.
C.
Recharge temperature.

D.
Solenoid valve operation.
25. MULTIPLE CHOICE
With reference to a Data Logger for a refrigeration system, which of the following
parameters should be monitored?
A.
Sea water temperature and pressure.
B.
Condensing temperature
C.
Refrigerant leakage
D.
Evaporating temperature
26.The induced voltage across a stationary conductor in a steady magnetic field is zero.
True
False
27.For leading power factor circuits, which of the following can be used?
A.
Shunt Capacitors only
B.
Shunt Reactors only
C.
Either Shunt Capacitors or Shunt Reactors
D.
Neither Shunt Capacitors Nor Shunt Reactors
28.A molded-case breaker provides protection against short-circuits by usinga/an
A.
Shading coil.
B.
Arc quencher.
C.
Electromagnet.
D.
Holding coil.
29.Fuses placed in series with a thermal trip = - type circuit breaker are used for
A.
Time-delay protection

B.
Short-circuit protection
C.
Short duration surge protection
D.
Sustained overload protection
30.MULTIPLE CHOICE
Which of the listed precautions should be taken when cleaning the internals of a motor
with compressed air?
A.
Open the machine on both ends so as to allow the air and dust to escape.
B.
Be certain that the circuit breaker is opened and tagged on the feeder panel.
C.
Be certain that the air is clean and as dry as possible.
D.
Ensure that the fuse in the motor is removed.
31.SINGLE CHOICE ONLY
A fuse that blows often should be replaced only with a fuse of
A.
the recommended current and voltage rating
B.
higher current and voltage rating
C.
higher current and lower voltage rating
D.
lower current and higher voltage rating
32.The greatest detrimental effect on idle electrical equipment, such as cargo pump
motors,is the
A.
Loss of residualmagnetism.
B.
Absorption of moisture in the insulation.
C.
Insulation varnish flaking.
D.
Dirt collecting on the windings.
Like Follow Post February 7 at 5:02pm

2 people like this.


Ashutosh Sharma qns 2 ans 270
February 7 at 5:37pm Like

Ashutosh Sharma qns 4 ans 5.83V ,qns 5 ans (1)_heat_______ (2)covalent bonds_are broken ______
(3)____large number of free electrons set free____ qns 6 ans free electrons _________ and
___holes____________(
February 7 at 5:52pm Like 1

Ashutosh Sharma qns 8 ans. ____holes_______.qns 9 ans open loop system__________.


February 7 at 5:53pm Edited Like 1

Balaji Barathalvar not sure abt my ans....... 1] 1 2] 270...See More


February 7 at 6:26pm Like 1

Balaji Barathalvar 7] ??? 8] holes 9] unstable system 10] insulators 11] ??? 12] ??? 13] clipper
February 7 at 6:32pm Like 1

Balaji Barathalvar 14] polar 15] 7.64 16] 1/4 17] 1/4 18,19,20] ???
February 7 at 6:39pm Like 1

Ashutosh Sharma 16 AND 17 IS I/2 AND HALVED


February 7 at 6:40pm Like

Ashutosh Sharma ITS SURE


February 7 at 6:41pm Like

Ashutosh Sharma 20 QNS ANS 300 AT


February 7 at 6:44pm Like 1

Balaji Barathalvar Ashutosh Sharma ans for 16 and 17 is 1/4 rite


February 7 at 6:48pm Like

Balaji Barathalvar Ashutosh Sharma ans for 7,11,12,13,18,19,20 pls


February 7 at 6:49pm Like

Balaji Barathalvar ans from 21 - 32 pls.......... somebody help us........


February 7 at 6:51pm Like

Ashutosh Sharma 11 QNS ANS CUT OFF VOLTAGE ( GOTHROUGH LINK AND ITS PAGE 3 TOPIC 8.2.4 )
http://www.hbcc.edu.sa/facpages/syedmuhammadasad/data_files/phys%20162/ch08.pdf
February 7 at 6:52pm Like 2


Ashutosh Sharma QNS 13 ANS clipper and limiter__
February 7 at 6:55pm Like 1

Ashutosh Sharma QNS 19 ANS B.


0.7 < VCE < 1.4 V NT FULL SURE
February 7 at 6:56pm Like

Ashutosh Sharma QNS 20 ANS 300 AT


February 7 at 6:56pm Like

Ashutosh Sharma ONS 21 ANS REACTIVE POWER


February 7 at 7:02pm Like

Jayant Negi 28) electromagnet


February 7 at 7:17pm Like 1

Jayant Negi 31) a


February 7 at 7:18pm Like 1

Jayant Negi 26)true

February 7 at 7:19pm Like

Jayant Negi 18)191.44


February 7 at 7:20pm Like 1

Jayant Negi 15) 0


February 7 at 7:20pm Like 1

Jayant Negi 12) 2.4 N


February 7 at 7:21pm Like 1

Ashutosh Sharma 29 B
February 7 at 7:23pm Like 1

Balaji Barathalvar Jayant Negi 15] 7.64


February 7 at 7:24pm Like 1

Ashutosh Sharma ONS 32 ANS IS B (USCG QNS NO 72)


February 7 at 7:26pm Edited Like

Balaji Barathalvar Jayant Negi pls xplain 18 and 12


February 7 at 7:27pm Edited Like

Jayant Negi Balaji Barathalvar for 15 pls explain...


18. as i read somewhere on a site.... v(rms)=100
V(peak)=100/.707=141.44
Since its sine wave is over a 50v dc....V peak=50 + v(peak)
=> 50+141.44= 191.44
February 7 at 7:29pm Like 1

Jayant Negi 12) F=BILsin (angle)


=> F=.6*20*.4 Sin 30
=>F=2.4
February 7 at 7:39pm Like 1

Balaji Barathalvar Jayant Negi average value of sine wave..(2*V peak)/pi


February 7 at 7:50pm Like 1

Jayant Negi Balaji Barathalvar i agree the formula is correct but for only half cycle of sine wave. :|
the question is for one complete cycle.... hence i said zero...
February 7 at 7:54pm Like

Allan Dsouza Thanx friends


February 7 at 11:20pm via mobile Like

Electrical-jan-2013 pradeep
*Question 1
Which of the listed precautions should be taken when
cleaning the internals of a
motor with compressed air?

A. Open the machine on both ends so as to allow the air and


dust to escape.
B. Be certain that the circuit breaker is opened and tagged
on the feeder panel.
C. Be certain that the air is clean and as dry as possible.
D. Ensure that the fuse in the motor is removed.
*Question 2
What is the value of Z in a series ac circuit where XL = 9
ohms, XC = 5 ohms and R =
8 ohms? Your answer should be correct to one decimal.
Variable Answer Units Correct to
Z ohms 1 decimal
Question 3
What type of rotor is used in split-phase motors?
A. Drum
B. Salient pole
C. Squirrel-cage
D. Wound-rotor
*Question 4
The voltage induced across a certain coil is 150 mV. A 100
?? resistor is connected
to the coil terminals. Calculate the induced current.
Variable Answer Units Correct to
I mA 1 decimal
Question 5
Where a thermal-acting breaker is required to be used in an
area of unusually high,
low, or constantly fluctuating temperatures, an ambient
compensating element must be
Page 3
NEW
used. This element consists of a
A. Cylindrical spring on the contact arm.
B. Conical spring on the contact arm.
Page 1
Electrical-jan-2013 pradeep
C. Second bimetal element.
D. Second electromagnet.
*Question 6
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?
A. Room temperature.
B. Liquid Line temperature.
C. Recharge temperature.
D. Solenoid valve operation.
*Question 7
A poly-phase motor driving an engine room pump fails to
start. When trying to
identify the cause of failure, which of the following steps
are applicable?
A. Ensure that the isolator is open.
B. Make sure that there is no restriction preventing
movement of pump/motor.
C. Check whether the overload relay has tripped.
D. Check whether battery is fully charged.
*Question 8
The induced voltage across a stationary conductor in a
steady magnetic field is

zero.
True
False
*Question 9
A poly-phase motor driving an engine room pump fails to
start. When trying to
identify the cause of failure, which of the following steps
are applicable?
A. Visually examine motor for open circuit faults.
B. Visually examine starter for open circuit faults.
C. Reverse the direction of electrical supply to check if it
works.
D. Perform the infinite resistance test.
*Question 10
The diode circuit which is used to clip off portions of
Page 2
Electrical-jan-2013 pradeep
signal voltages is called a
(1)________.
1)
*Question 11
Four 6F capacitors are connected in parallel. Calculate the
effective capacitance.
Variable Answer Units Correct to
C Farads 0 decimal
Question 12
Time delayed or delayed action-type fuses are designed to
A. prevent grounds in branch circuits
B. prevent opens in motor circuits
C. permit momentary overloads without melting
*Question 13
The opposition to the establishment of magnetic lines of
force in a magnetic circuit
is called the circuit's
A. resistance
B. reluctance
C. impedance
D. inductance
Question 14
A molded-case breaker provides protection against
short-circuits by usinga/an
A. Shading coil.
B. Arc quencher.
C. Electromagnet.
D. Holding coil.
Question 15
With reference to a Data Logger for a refrigeration system,
which of the following
parameters should be monitored?
A. Sea water temperature and pressure.
B. Condensing temperature
C. Refrigerant leakage
D. Evaporating temperature
Question 16
Which of the listed conditions is an advantage of a PN diode
Page 3
Electrical-jan-2013 pradeep
over a vacuum diode?
A. Longer life.

B. No warm up time.
C. Less delicate.
D. All of the above.
*Question 17
The apparent power in a purely inductive circuit is also
known as
A. true power
B. lead power
C. induced power
D. reactive power
*Question 18
A 45 ohm resistor is connected to a 3V battery. Calculate
the power dissipation of
the resistor.
Variable Answer Units Correct to
p milliwatts 0 decimal
Question 19
The winding resistance of a coil can be increased by _______
the number of turns or
using a ______ wire.
Page 13
NEW
A. increasing, thicker
B. decreasing, thicker
C. increasing, thinner
D. decreasing, thinner
Question 20
The current in a semiconductor is produced by:
A. Electrons
B. Neutrons
C. Protons
D. Holes
Question 21
Which of the listed devices may be installed on a large
turbo-electric alternating
current propulsion generator?
A. Temperature detector coils inserted in the stator slots
Page 4
Electrical-jan-2013 pradeep
for measuring stator
temperature.
B. A CO2 fire extinguishing system.
C. Electric space heaters to prevent condensation of
moisture.
D. All of the above.
*Question 22
Open-loop transfer function of a system having one zero with
positive real values is
called (1)________ phase function.
1)
*Question 23
Which of the following capacitor types has a di-electric
constant of 1.000?
A. Air Gap
B. Vacuum
C. Water
D. Electrolytics
*Question 24
Which of the following statements represents an application

of a silicon controlled
rectifier?
A. To provide DC power for a main propulsion motor.
B. For use as a voltage reference diode.
C. For sensing flame in an automated burner.
D. To eliminate power supply hum.
Question 25
Tightly knit metal braid wire can be used with a printed
circuit board when
A. Conductor flexibility is required
B. De-soldering components in the circuit
C. Electrically produced magnetic fluxes would cause
inaccuracies in adjacent
components
D. Reactance in the circuit must be kept to a minimum
Page 5

Você também pode gostar