Escolar Documentos
Profissional Documentos
Cultura Documentos
Project Specification
SECTION 10 28 13
TOILET ACCESSORIES
PART 1:
1.01
A.
GENERAL
SECTION INCLUDES
Toilet, bathroom and janitor room accessories and finishes including, but not limited to the
following:
1. Toilet, bath, shower, and washroom accessories.
2. Attachment hardware.
3. Multi roll toilet paper holder.
4. Sanitary napkin disposal.
5. Paper towel cabinet/waste receptacle.
6. Soap dispenser.
7. Mirror with frame.
8. Coat hooks.
9. Grab bars.
10. Towel bars.
11. Mop and broom holder.
12. Shower curtain rod.
13. Fixing accessories.
1.02
RELATED SECTIONS
A.
Section 04 20 00
Unit Masonry.
B.
Section 05 52 00
Metal Railings.
C.
Section 07 14 00
D.
Section 07 92 00
Joint Sealers.
E.
Section 08 83 00
Mirrors.
F.
Section 09 30 13
Ceramic Tile.
G.
Mechanical.
H.
Division 26
Electrical.
TOILET ACCESSORIES
SECTION 10 28 13 - 1
MINISTRY OF HOUSING
Western Sector Projects
Sitework & Infrastructure
OMRANIA and ASSOCIATES
1.03
Project Specification
REFERENCES
A.
ADAAG
B.
ANSI A 117.1
C.
ANSI A 137.1
D.
ASTM A 123
E.
ASTM A 167
F.
ASTM A 269
G.
ASTM A 366
H.
ASTM A 653M
I.
ASTM A 1008
J.
ASTM B 456
K.
NEMA LD-3
1.04
Heat-Resisting
SUBMITTALS
A.
B.
Product Data: Submit to the Engineer for approval manufacturers catalog cuts on items
specified herein and obtain approval prior to delivery.
C.
Accessories Schedule: 90 days after the award of the contract, prepare and submit for
approval, six (6) copies, with electronic disc, of an accessories schedule listing accessories
to be provided. Manufacturers, catalogue references, type, number, finish and location of
each item shall be furnished. Lists not complying with the above shall be considered
incomplete and shall be returned for revision.
D.
Prior to submittal of the final schedule and prior to the final ordering of material, submit
one sample for each type of accessory finish required for project, and tagged with full
description for coordination with the schedule.
E.
Samples will be returned upon the request and at the expense of the Contractor.
F.
Samples: Submit one sample of each component, illustrating color and finish.
G.
TOILET ACCESSORIES
SECTION 10 28 13 - 2
MINISTRY OF HOUSING
Western Sector Projects
Sitework & Infrastructure
OMRANIA and ASSOCIATES
1.05
A.
1.06
A.
1.07
Project Specification
REGULATORY REQUIREMENTS
Conform to ANSI A 117.1 code for access for the handicapped.
FIELD MEASUREMENTS
Verify that field measurements are as instructed by the manufacturer.
COORDINATION
A.
B.
Coordinate the work with the placement of internal wall reinforcement and reinforcement to
receive anchor attachments.
1.08
WARRANTY
A.
B.
C.
Correct defective work within a 3 year period after Substantial Completion and include for
replacement and making good any damage caused during replacement.
PART 2:
2.01
PRODUCTS
MATERIALS
A.
B.
C.
D.
E.
F.
G.
Stainless Steel: When used for metal accessories and shall be AISI Type 302 or 304. Exposed
surfaces of stainless steel shall receive a No. 4 satin finish as approved by the Engineer.
H.
I.
Chrome Plating: When specified shall be applied over a coating of nickel. On steel, the nickel
coating shall be applied over a coating of copper. Chrome plated surfaces shall receive a
US26D finish, as approved by the Engineer. Die-cast base metal is not acceptable.
J.
Fastening Devices: Anchors, clips, screws, bolts, expansion shields and plates shall be
furnished with each accessory as required by the type of accessory and the construction to
which it is attached, and shall be concealed where possible. Finish of exposed fastening
devices shall match that of the accessory. Exposed to view fastening devices shall be tamperresistant.
TOILET ACCESSORIES
SECTION 10 28 13 - 3
MINISTRY OF HOUSING
Western Sector Projects
Sitework & Infrastructure
OMRANIA and ASSOCIATES
Project Specification
K.
Ceramic Accessories: In accordance with ANSI A 137.1 color and finish to match
surrounding tiling unless otherwise indicated.
L.
Mirrors: Locations and size shown on the Drawings or listed in the Schedules shall be framed
with satin finished stainless steel, with corners welded, ground smooth and finished to match
adjacent surfaces. Mirror shall have theft-resistant concealed mountings with two set screws.
Glass for mirrors shall be "silvering" quality, conforming to Federal Specification DD-G00451. Mirrors shall receive two coats of silver and electrolytically clad copper.
M.
White Enamel Finish: As indicated, shall be applied to exposed surfaces of galvanized sheet
steel which shall be bonderized after fabrication and finished with durable baked white
enamel.
N.
Sound-Deadening Material: Provide at the back of recessed toilet room accessories. Apply
appropriate and approved material by spraying or troweling to a thickness of not less than 3.2
mm.
2.02
ACCESSORIES
A.
General: Provide products of the same manufacturer for each type of accessory unit and for
units exposed in the same areas, unless otherwise acceptable to the Engineer.
B.
Multi-Roll Toilet Paper Holder: Surface mounted, reserve roll type; 0.7 mm, 304 stainless
steel door and cabinet; satin finish all exposed surfaces; tumbler lock; approximately 150 mm
wide, 275 mm high, 150 mm deep. Hem exposed edges.
C.
Paper Towel Cabinet/Waste Receptacle: Recessed mounted, combination towel dispenser and
waste receptacle; 0.7 mm, 304 stainless steel door, cabinet and waste container; towel
capacity, 600 C-fold or 800 multi-fold; waste container capacity, 45 l; tumbler lock towel
dispenser and waste container; approximately 142 mm high by 400 mm wide; for mounting in
100 mm wall. Provide vinyl liner for waste and equip steel waste container with hanger hooks
for vinyl liner.
D.
Soap Dispenser: Lavatory mounted soap dispenser with 100 mm spout and 470 ml plastic
container mounted below countertop.
E.
Mirror With Frame - Without Shelf: 6 mm float or plate glass, electro-copper plated mirror
guaranteed for 15 years against silver spoilage. 304 stainless steel with satin finish angle
frame, 0.7 mm, approximately 16 mm x 16 mm with corners mitered, welded and ground
smooth. 0.9 mm galvanized steel back, concealed mounting devices.
F.
Single Coat Hook: Satin stain steel, surface mounted coat hook. Provide complete with
stainless steel mounting screws designed for specific substrate (include plugs or expansion
shields where required). Size: 32 mm x 32 mm x 28 mm projection.
G.
Mop and Broom Holder with Shelf : 304 stainless steel, satin finish, not less than 0.7 mm;
200 mm wide shelf, length as indicated. Hem exposed edges.
H.
TOILET ACCESSORIES
SECTION 10 28 13 - 4
MINISTRY OF HOUSING
Western Sector Projects
Sitework & Infrastructure
OMRANIA and ASSOCIATES
2.03
Project Specification
FABRICATION
A.
B.
Form exposed surfaces from single sheet of stock, free of joints. Form surfaces flat without
distortion. Maintain surfaces without scratches or dents.
C.
Fabricate grab bars of tubing, free of visible joints, return to wall with end attachment flanges.
Form bar with 50 mm clear of wall surface.
D.
Shop assemble components and package complete with anchors and fittings.
E.
Provide steel anchor plates, adapters, and anchor components for installation.
2.04
FINISHES
A.
Galvanizing: ASTM A 123 to 380 g/m2 galvanized ferrous metal and fastening devices.
B.
Shop Primed Ferrous Metals: Pre-treat and clean, spray apply one coat primer and bake.
C.
Enamel: Pre-treat to clean condition, apply one coat primer and minimum two coats
electrostatic baked enamel.
D.
E.
F.
Back paint components where contact is made with building finishes to prevent electrolysis.
G.
PART 3:
3.01
EXECUTION
EXAMINATION
A.
B.
Verify that site conditions are ready to receive work and dimensions are as instructed by the
manufacturer.
C.
3.02
PREPARATION
A.
B.
Templates: Furnish to the Toilet Partition subcontractor templates required to locate drilled
holes and cutouts for installation of bearing support to all partition mounted accessories.
C.
TOILET ACCESSORIES
SECTION 10 28 13 - 5
MINISTRY OF HOUSING
Western Sector Projects
Sitework & Infrastructure
OMRANIA and ASSOCIATES
3.03
Project Specification
INSTALLATION
A.
B.
C.
Toilet Room Accessories: Install where shown on the Drawings, as recommended by the
manufacturer and as directed by the Engineer, rigidly secured and shall be in perfect
alignment with other fixtures.
D.
Mirrors: Install in a perfectly flat plane, showing no distortion of image, in strict conformance
with approved shop drawings.
E.
Metal Trim: Items exposed in the finished work shall be free from buckle, warping and oilcanning effects. Metal to metal contact shall have hairline joints.
F.
G.
Provide anchors, bolts and other necessary anchorages, and attach accessories securely to
walls and partitions in locations as shown or directed.
H.
Install concealed mounting devices and fasteners fabricated of the same material as the
accessories, or of galvanized steel, as recommended by the manufacturer.
I.
Install exposed mounting devices and fasteners finished to match the accessories.
J.
K.
Secure toilet room accessories in accordance with the manufacturer's instructions for each
item and each type of substrate construction.
L.
3.04
A.
B.
Suitably protect work in order to maintain finishes in perfect condition until Substantial
Completion and acceptance. Any changed or defective work shall be removed and replaced at
no additional cost to the Owner.
C.
Finished installation shall be sound and free from defects of materials and workmanship.
After the inspection of the installation and its approval by the Engineer, protection, labels,
smears and stains shall be removed and mirrors shall be washed clean.
END OF SECTION
TOILET ACCESSORIES
SECTION 10 28 13 - 6