Escolar Documentos
Profissional Documentos
Cultura Documentos
Service
Service
Service
221E2SB/00
221E2SB/10
221E2SB/27
221E2SB/62
221E2SB/69
221E2SB/71
221E2SB/73
Chassis: Meridian 2
221E2SB/75
221E2SB/93
221E2SB/94
221E2SB/96
Description
221EL2SB/00
221EL2SB/10
221EL2SB/62
221EL2SB/69
221EL2SB/75
221EL2SB/93
221EL2SB/96
Page
Table of Contents..........................................1
Revision List..............................................2
Important Safety Notice................................3
1. Monitor Specifications.........................................4
2. LCD Monitor Description.....................................7
3. Operation Instructions.........................................9
3.1General Instructions....9
3.2 Control Buttons...9
3.3 OSD Menu.................................10
4. Input/output Specification...........................11
4.1 Input Signal Connector.............................11
4.2 Resolution & Preset Modes.................................12
4.3 Pixel Defect Policy13
4.4 Failure Mode of Panel ..15
5. Block Diagram.................16
5.1 Scaler Board.........................................16
5.2 Adapter/Inverter/Converter Board...................17
6. Schematic Diagram.............................................. 18
6.1 Scaler Board.18
6.2 Adapter Board.................................................22
Description
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Page
K
Subject to modification
Mar.29, 2010
Meridian 2
Revision List
Version
Release Date
Revision History
A00
Mar.29,2010
A01
Apr.30,2010
A02
May.21,2010
A03
Jun.30,2010
Meridian 2
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics, may create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from Philips.
Philips assumes no liability, express or implied, arising out of any unauthorized modification of design.
FOR PRODUCTS CONTAINING LASER:
DANGER- There is invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit:
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment persons body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth
may damage the panel.)
Meridian 2
1. Monitor Specifications
Technical specifications
Picture/Display
LCD Panel Type
TFT-LCD
Backlight
Panel Size
Aspect Ratio
16:9
Pixel Pitch
0.248 x 0.248 mm
Brightness
250 cd/m
SmartContrast
1000:1
5 ms
Optimum Resolution
Viewing Angle
Picture Enhancement
SmartImage Lite
Display Colors
16.7 M
56Hz - 76Hz
wHorizontal Frequency
30kHz - 83kHz
sRGB
YES
Connectivity
Signal Input
Input Signal
Convenience
User Convenience
OSD Languages
Other convenience
Kensington lock
Stand
Tilt
-3 / +12 (221E2/221EL2)
Power (221E2)
On mode
24 W (typ.)
AC Input Voltage at
AC Input Voltage at
AC Input Voltage at
21.53 W
21.41 W
21.39 W
Sleep
0.43 W
0.42 W
0.43 W
Off
0.42 W
0.42 W
0.43 W
Energy Consumption
(EnergyStar 5.0 test method)
Meridian 2
AC Input Voltage at
AC Input Voltage at
AC Input Voltage at
Normal Operation
73.48 BTU/hr
73.07 BTU/hr
73.00 BTU/hr
Sleep
1.47 BTU/hr
1.43 BTU/hr
1.47 BTU/hr
Off
1.43 BTU/hr
1.43 BTU/hr
1.47 BTU/hr
AC Input Voltage at
AC Input Voltage at
AC Input Voltage at
18.05 W
18.04 W
18 W
Sleep
0.43 W
0.42 W
0.41 W
Off
0.42 W
0.42 W
0.40 W
AC Input Voltage at
AC Input Voltage at
AC Input Voltage at
Normal Operation
75.52 BTU/hr
75.48 BTU/hr
73.07 BTU/hr
Sleep
1.47 BTU/hr
1.43 BTU/hr
1.71 BTU/hr
Off
1.43 BTU/hr
1.43 BTU/hr
1.67 BTU/hr
Power Supply
AC Adapter, 1.2V==3.0A
Heat Dissipation*
Power (221EL2)
On mode
Energy Consumption
(EnergyStar 5.0 test method)
Heat Dissipation*
23.8 W (typ.)
Dimension
Product with Stand (W x H x D)
526 x 370 x 42 mm
Box Dimension (W x H x D)
Weight
Product with Stand
3.10 kg
3.0 kg
4.36 kg
Operating Condition
Temperature Range (operation)
0C to 40 C
-20C to 60C
Relative Humidity
20% to 80%
Altitude
MTBF
Meridian 2
Environmental
ROHS
YES
EPEAT
Silver (www.epeat.net)
Packaging
100% recyclable
Cabinet
Color
Black / Black
Finish
Glossy / Texture
Note:
This data is subject to change without notice.
Go to www.philips.com/support to download the latest version of leaflet.
Meridian 2
CCFL Drive.
CCFL backlight
Inverter Board
DC 12V
Adapter Board
DVI-D
Scaler Board
D-SUB
Key Board
Video signal, DDC
HOST Computer
AC IN
90 ~ 264 V
Meridian 2
221EL2
The LCD monitor will contain a scaler board, an adapter board, a converter board and a key board. The scaler
board houses the flat panel control logic, brightness control logic and DDC.
The adapter board will provide AC to DC Inverter voltage to drive the backlight of panel and the scaler board chips
each voltage.
Monitor Block Diagram
LED Drive
Converter Board
DC 12V
Adapter Board
LED Panel
DVI-D
Scaler Board
D-SUB
Key Board
Video signal, DDC
HOST Computer
AC IN
90 ~ 264 V
Meridian 2
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off.
1. DC power input
2. VGA input
3. DVI-D input (available for selected models)
4. Kensington anti-thief lock
Install base stand
1. Place the monitor face down a smooth
surface taking care to avoid scratching or
damaging the screen.
1.
2.
3.
10 Meridian 2
3.3 OSD Menu
below.
Main menu
Sub menu
Meridian 2
Pin No.
Signal Name
Pin No.
Red video
Green video
10
Sync GND
Blue video
11
GND
GND
12
SDA
Cable Detect
13
H-Sync (or H + V)
Red GND
14
V-sync
Green GND
15
SCL
Blue GND
Signal Name
Signal Name
Pin No.
TMDS RX2-
13
Floating
TMDS RX2+
14
+5V Power
TMDS Ground
15
Ground
Floating
16
Floating
17
TMDS RX0-
DDC Clock
18
TMDS RX0+
DDC Data
19
TMDS Ground
Floating
20
Floating
TMDS RX1-
21
Floating
10
TMDS RX1+
22
TMDS Ground
11
TMDS Ground
23
TMDS Clock+
12
Floating
24
TMDS Clock-
11
12 Meridian 2
4.2 Resolution & Preset Modes
Maximum Resolution
For 221E2/221EL2
1920 x 1080 at 60 Hz (analog input)
1920 x 1080 at 60 Hz (digital input)
Recommended Resolution
For 221E2/221EL2
1920 x 1080 at 60 Hz (digital input)
H. freq (kHz)
Resolution
V. freq (Hz)
31.47
640 x 480
59.94
37.88
800 x 600
60.32
48.36
1024 x 768
60.00
54.00
1152 x 864
60.00
44.77
1280 x 720
59.86
47.78
1280 x 768
59.87
49.70
1280 x 800
59.81
60.00
1280 x 960
60.00
63.89
1280 x 1024
60.02
47.71
1360 x 768
60.02
55.47
1440 x 900
59.90
55.94
1440 x 900
59.89
75.00
1600 x 1200
60.00
64.67
1680 x 1050
59.88
65.29
1680 x 1050
59.95
66.59
1920 x 1080
59.93
74.04
1920 x 1200
59.95
67.50
1920 x 1080
60.00
Meridian 2
13
each category.
or sub pixels that are always lit or on. That is, a Bright
Note:
14
Meridian 2
pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel
defects during the warranty period, a TFT LCD panel in
a Philips flat panel monitor must have pixel or sub pixel
defects exceeding the tolerances listed in the following
tables.
Acceptable level
221E2/221EL2
1 lit subpixel
>15mm
Acceptable level
221E2/221EL2
1 dark subpixel
5 or fewer
2 or fewer
>15mm
5 or fewer
Acceptable level
221E2/221EL2
5 or fewer
Meridian 2
4.4 Failure Mode Of Panel
Quick reference for failure mode of LCD panel
Failure description
Phenomenon
15
16
Meridian 2
5. Block Diagram
5.1 Scaler Board
Crystal
14.31818MHZ
(X401)
Keypad Interface
Panel Interface
(CN401)
(CN301)
Scaler IC TSUMU58NWHL-LF-1
Flash Memory
EN25F20-100GCP
(U402)
RGB
EEPROM
AT24C02BN
(U101)
H/Y Sync
EDID_WP
DDC1_SCL
DDC1_SDA
D-Sub Connector
(CN101)
RX+/RXC+/-
EEPROM
AT24C02BN
(U102)
EDID_WP
DDCSCL2
DDCSDA2
DVI Connector
(CN102)
Meridian 2
17
12V
Bridge
Rectifier
and Filter
EMI filter
Rectifier
Diodes
Transformer
Start Resistor
(R934, R906)
Feedback
PWM Control
Power Switch
(IC901)
(Q901)
Circuit
Photocoupler
(IC902)
Inverter Board
Output
Circuit
MOSFET
APM4548A
Transformer
(PT801, PT802)
12V
Lamp
5V
Protect Circuit
PWM Control
ta9687GN
(IC801)
Feedback Circuit
ENA
DIM
Converter Board
Boost Circuit
12V
LED
panel
OVP Circuit
Current Feedback
Setup-up Controller
TA9690GN
DIM
(IC801)
ENA
18
Meridian 2
6. Schematic
6.1 Scaler Board (715G3598M0K000004L)
Remark: Parts position can be searched by using FIND function in PDF.
FB102
Input
VGA_B+
R103 1K1/16W
R104 1K1/16W
R106
2.2K1/16W
R107
2.2K1/16W
C103
22P 50V
DSUB_H 5
DSUB_V 5
16
DSUB_SDA
DSUB_SCL 15
14
100OHM1/16W
13
R113
11
H_Sy nc
6
5
4
FB103
V_Sy nc
VGA_G+
2
BEAD
VGA_PLUG
VGA_G+
1
2
3
U103
AZC199-04S
I/O1 I/O4
GNDVDD
I/O2 I/O3
6
5
4
VGA_PLUG
VGA_R+
2
BEAD
R116
75OHM1/16W
GND
GND
DSUB_G+ 5
R114
47 OHM 1/16W
C110
47N 16V
DSUB_G- 5
R115
10OHM1/16W
C111
47N 16V
DSUB_R+ 5
C114
47N 16V
DSUB_R- 5
C113
5PF 50V
DVI_5V
FB104
DVI_HPD
DSUB_5V
300 OHM
R118 100OHM1/16W
R119 100OHM1/16W
R120 10K1/16W
FB106
DDC2_SCL 5
DDC2_SDA 5
D101
BAV70
300 OHM
ESD_VCC
3
11
3
19
22
DDC2_SCL
DDC2_SDA
C118
1000pF 50V
C119
1000pF 50V
R124
4.7K1/16W
18
17
10
9
2
1
13
12
5
4
21
20
23
24
R126
R127
R128
R129
R130
R131
10OHM1/16W
10OHM1/16W
10OHM1/16W
10OHM1/16W
10OHM1/16W
10OHM1/16W
RX0P
RX0N
RX1P
RX1N
RX2P
RX2N
RX0P
RX0N
RX1P
RX1N
RX2P
RX2N
5
5
5
5
5
5
R125
4.7K1/16W
R123
10K1/16W
C116
220N16V
U101
8
7
6
5
DDC1_SCL
DDC1_SDA
5 DDC_WP
1
2
3
4
VCC A0
WP
A1
SCL A2
SDA VSS
AT24C02BN-SH-T
CMVCC1
FB105
3,4,5,8 CMVCC1
R132
R134
1
2
3
U107
AZC199-04S
I/O1 I/O4
GNDVDD
I/O2 I/O3
ESD_VCC1
6
5
4
1
2
3
U105
AZC199-04S
C121
1000pF 50V
I/O1 I/O4
GNDVDD
I/O2 I/O3
ESD_VCC1
6
5
4
1
2
3
U106
AZC199-04S
I/O1 I/O4
GNDVDD
I/O2 I/O3
10OHM1/16W
10OHM1/16W
RXCP
RXCN
RXCP 5
RXCN 5
VCC3.3
ESD_VCC1
R133
10K1/16W
C120
1000pF 50V
300 OHM
C115
100N 16V
D102
BAV70
ESD_VCC1
6
5
4
DAT0+
DAT0DAT1+
DAT1DAT2+
DAT2DAT3+
DAT3DAT4+
DAT4DAT5+
DAT5clk+
clk-
C108
47N 16V
R117
47 OHM 1/16W
CMVCC1
1/3shield
2/4shield
0/5shield
clk shield
DSUB_SOG 5
R111
10OHM1/16W
FB101
VGA_B+
VGA_R-
8
15
6
7
14
16
C107
1000pF 50V
ESD_VCC
D-SUB 15P
VSYNC
SYNC GND
DDC SCL
DDC SDA
+5V
HPD
R110
470OHM1/16W
C109
5PF 50V
VGA_G-
C124
100N 16V
VGA_R+
CN102
JACK
DSUB_B- 5
75OHM1/16W
DSUB_5V
17
100OHM1/16W
26
25
5 DDC1_SDA
DSUB_SDA 12
DDC1_SDA
ESD_VCC
R112
VGA_BVGA_B+
ZD101
VGA_G- RLZ5.6B
VGA_G+
VGA_RVGA_R+
C106
47N 16V
DDC1_SCL
R109
47 OHM 1/16W
5 DDC1_SCL
I/O1 I/O4
GNDVDD
I/O2 I/O3
DSUB_B+ 5
75OHM1/16W
C104
22P 50V
1
2
3
C102
47N 16V
C105
5PF 50V
VGA_B-
DSUB_SCL
CN101
10
5
9
4
8
3
7
2
6
1
R105
10OHM1/16W
R108
U104
AZC199-04S
R101
0R05 1/10W
BEAD
H_Sy nc R102
V_Sy nc
DVI_HPD
VGA_PLUG
R137
4.7K1/16W
R135
10K1/16W
R139
6.8K1/16W
DET_CABLE 5
DDC2_SCL
DDC2_SDA
5 DDC_WP
R138
4.7K1/16W
C117
220N16V
R136
10K1/16W
U102
8
7
6
5
VCC A0
WP
A1
SCL A2
SDA VSS
1
2
3
4
AT24C02BN-SH-T
DVI_5V
Meridian 2
19
CN301
5 PA[0..9]
PA[0..9]
5 PB[0..9]
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
LVB0M
LVB1M
LVB2M
LVBCKM
LVB3M
LVA0M
LVA1M
LVA2M
LVACKM
LVA3M
RXO0RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3-
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
32
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
PB[0..9]
CONN
FB301
2
120 OHM
CMVCC1
C302
22UF 16V
2,4,5,8 CMVCC1
R306
Q301
D
D
D
D
5
6
7
8
R305
10K1/16W
AO3401
Q302
5 PPWR_ON#
R303
4.7K1/16W
R307
NC
LMBT3904LT1G
22K1/16W
C304
100N 16V
NC/AO4411
C303
220N16V
4
3
2
1
R304
U301
G
S
S
S
100K1/16W
3D
1
G
AO3401L
2
S
C305
1uF 16V
R308
10K1/16W
LVB0P
LVB1P
LVB2P
LVBCKP
LVB3P
LVA0P
LVA1P
LVA2P
LVACKP
LVA3P
PANEL_VCC
R301
220 OHM 1/4W
PANEL_VCC
RXO0+
RXO1+
RXO2+
RXOC+
RXO3+
RXE0+
RXE1+
RXE2+
RXEC+
RXE3+
CMVCC1
R302
220 OHM 1/4W
C301
100N 16V
20 Meridian 2
Remark: Parts position can be searched by using FIND function in PDF.
SOT 252
Power
12
VIN
VOUT(TAB)
ADJ(GND)
+12V
1
2
3
4
5
6
7
8
9
10
U702
G1117-33T43UF
CMVCC1
1
R707
0R05 1/10W
BKLT-VBRI
BKLT-EN
3
2
1
D707
SM340A
D708
SM340A
CONN
R708
NC/0R05 1/10W 5%
SOT 223
VCC3.3
U701
11
CMVCC1
CN702
VO
Dropout voltage
must < 0.8V @ 600mA
GND
VI
C709
100N 16V
C708
100N 16V
C707
22UF 16V
VCC3.3
CMVCC1
1
CMVCC1
SOT 223
D703
SM340A
R702
10K1/16W
U704
3
VI
VO
Dropout voltage
must < 0.8V @ 400mA
C702
100N 16V
Q701
LMBT3904LT1G
GND
BKLT-EN
R703
10K1/16W
D704
SM340A
on_BACKLIGHT 5
2
R704 22K1/16W
SOT 252
VCC1.8
CMVCC1
C705
100N 16V
C704
22UF 16V
C706
100N 16V
GND
U703
NC/AZ1117D-1.8-E1
3
2
IN
OUT
R705
10K1/16W
R706
BKLT-VBRI
adj_BACKLIGHT 5
100OHM1/16W
C713
100nF 25V
FB703
0R05 1/10W
CMVCC1
U705
9
8
7
6
5
R712
100K1/16W
Thermal Pad
SW
BST
EN
VIN
FREQ COMP
GND
FB
1
2
3
4
L701
CMVCC1 2,3,5,8
MP1584EN
22UH
C710
1N 50V
C711
1N 50V
R713
6K8 1/16W 1%
C714
1N 50V
C721
100N 16V
R711
33K 1/16W
C722
150pF 50V
R727
180K 1/16W 5%
R726
100K1/16W
+12V
+12V
FB701
1
BEAD
CN701
2
3
2
1
C715
1N 50V
C720
10uF 25V
C718
180uF 16V
C719
100nF 25V
JACK
C723
R714
1K3 +-1% 1/16W
10uF 25V
C716
470uF 10V
C717
100N 16V
ZD702
NC/RLZ6.2B
1
C712
100nF 25V
D701
SM340A
Meridian 2
Remark: Parts position can be searched by using FIND function in PDF.
VCC3.3 FB402
Scaler
VPLL
VCC3.3
300OHM
FB401
AVDD
C408
100N 16V
300OHM
C407
100N 16V
37
38
39
40
3 PPWR_ON#
48
84
R423 0R05OHM1/16W
96
R421
100K1/16W
34
VDDC
51
66
82
VDDC
VDDC
VDDC
24
16
98
32
49
56
75
VDDP
VDDP
VDDP
VDDP
AVDD_33
AVDD_33
TSUMU58NWHL-LF-1
REFM
X401
14.31818MHZ/32PF
97
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
GPIO_P40
GPIO_P41
GPIO_P42
GPIO_P23
GPIO_P22
LVDS
SDO
SCZ
SCK
SDI
GPIO_P15/PWM0
PWM2/GPIO_P24
GPIO_P12
PWM1/GPIO_P25
GPIO_P27/PWM1
RST
GPIO_P17/SAR0
GPIO_P00/SAR1
GPIO_P01/SAR2
GPIO_P02/SAR3
GPIO_P06
GPIO_P07
PWM0/GPIO_P26
GPIO_P13
GPIO_P14
GPIO_P16/PWM2
XOUT
67
68
69
70
71
72
73
74
77
78
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PB[0..9]
C410
100N 16V
R425
R409
NC/100OHM1/16W
100OHM1/16W
R406
22K1/16W
POWER_KEY#
WP
Q401
on_BACKLIGHT 4
adj_BACKLIGHT 4
R415
R416
R417
91
92
93
94
95
99
100OHM1/16W
100OHM1/16W
100OHM1/16W
CMVCC1
LMBT3904LT1G
R407
10K1/16W
C416
100N 16V
C412
100N 16V
VCC3.3
R413
NC/0R05 1/16W
KEY1
KEY2
R404
4.7K1/16W
R402
2.2K1/16W
DET_CABLE 2
R419
Q402
LMBT3906LT1G
LED_ORANGE
Volume 8
AUDIO_MUTE
LED_GRN/BLUE
R414
0R05OHM1/16W
2,3,4,6,8 CMVCC1
XIN
R438
10K1/16W
BYPASS
LED_GRN/BLUE
10K1/16W
LED_G
R403
0R05 1/10W
LED_R
R405
0R05 1/10W
Q403
LMBT3906LT1G
R420
4.7K1/16W
LED_ORANGE
R436
R437
100OHM1/16W
100OHM1/16W
MSCL
MSDA
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
44
43
R439
10K1/16W
VCC3.3
CN402
CONN
1
2
3
4
2
5
11
29
33
50
57
76
79
83
NC
MODE
C411
100N 16V
CMVCC1
VCC3.3
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
52
53
C406
100N 16V
DDC_WP 2
85
86
87
88
89
90
C405
100N 16V
VDDC
C409
100N 16V
PB[0..9] 3
41
42
35
47
C404
100N 16V
4 VCC1.8
PA[0..9] 3
36
45
46
R428 100OHM1/16W
C422
80
100N 16V
C403
100N 16V
EN25F20-100GCP
C419
10U 10V
CS# VCC
DO HOLD#
WP# CLK
VSS
DI
8
7
6
5
C402
10U 10V
WP
1
2
3
4
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
PA[0..9]
U402
R412
10K1/16W
54
55
58
59
60
61
62
63
64
65
VCC1.8
RX2P
RX2N
RX1P
RX1N
RX0P
RX0N
RXCKP
RXCKN
DDCD_SDA
DDCD_SCL
REFP
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
25
VDDP
2,4 VCC3.3
81
26
VCTRL
100N 16V
C417
VCC3.3
CMVCC1
RIN0P
RIN0M
GIN0P
GIN0M
SOGIN0
BIN0P
BIN0M
HSY NC0
VSYNC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
C415
100N 16V
VDDC
15
R401 390R 1/16W 1% REXT
AVDD
C401
220N16V
3
4
6
7
9
10
12
13
100
1
AVDD_33
8
14
2 RX2P
2 RX2N
2 RX1P
2 RX1N
2 RX0P
2 RX0N
2 RXCP
2 RXCN
2 DDC2_SDA
2 DDC2_SCL
23
22
20
19
21
18
17
27
28
30
31
AVDD_33
AVDD_33
DSUB_R+
DSUB_RDSUB_G+
DSUB_GDSUB_SOG
DSUB_B+
DSUB_BDSUB_H
DSUB_V
DDC1_SDA
DDC1_SCL
VDVI
C414
100N 16V
C418
C413
NC 100N 16V
100N 16V
VCC3.3
2
2
2
2
2
2
2
2
2
2
2
VCC3.3
VMPLL
VDVI VMPLL
VCC3.3 FB404
300OHM
Eon
U402
020
(93G 22-53B-H)
18 pF
27 pF
(93G 22-53-J)
32 pF
47 pF
CONN
FB408
1
CMVCC1
2
120 OHM
FB409
1
2
NC/120 OHM
LED_R
C434
ZD402
C435
ZD403
NC/RLZ5.6B
3.9K1/16W
ZD401
NC/0.1uF 16V
CL of SPEC
C433
NC/RLZ5.6B
X401
C432
3.9K1/16W
C431
R433
NC/0.1uF 16V
020A
X'TAL
Normal Function : CL = Cs + ((Cg*Cd)/(Cg+Cd))
P.S : Assume Cs = 4 pF
100N 16V
U402
Befor AOC ID2007 OSD
FB406 0R
KEY 2
POWER_KEY#
LED_G
LED_R
100N 16V
SST
010A
0R
CN401
1
2
3
4
5
6
7
Eon
FB405
KEY 1
R432
NC/RLZ5.6B
U402
SST
R431
NC/0.1uF 16V
VCC3.3
21
22 Meridian 2
6.2 Adapter Board (715G3980P0D0000030)
Remark: Parts position can be searched by using FIND function in PDF.
R908
100 OHM 1/4W
R914
C908
T901
C911
2N2 500V
2N2 500V
D906
1
+12V/3A
L903
0.8uH
Diode MBR20100CT
R918
C907
82uF 450V
C925
R934
10K 1/4W
C909
10NF1KV
R938
R907
1500PF2KV
FL2
NC
5
4
9
D902
1N4007
R906
10K 1/4W
+ C919
+ C918
680UF 25V
680UF 25V
C927
+
100uF 25V
C920
1U 25V
20K 1/10W 5%
LED1
LED
FL1
8
700uH
KBP306G-05
BD901
D903
R941
3
1R5 1/8W 5%
C910
100N 50V
C929
1N4007
47uF/50V
IC901
100pF50V
4
LD7750GS
8
7
6
5
SMK0965F
R942
100OHM +-5% 1/8W
D908 LL4148
R947
Q901
R922
470OHM +-5% 1/8W
4.7 OHM
R905
10K OHM +-5% 1/8W
R940
R902
0.47OHM2W
R904
R911
2KOHM 1/10W
IC902
PC123X2Y FZOF
3
14mH
R901
R919
45.3KOHM +-1% 1/10W
R910
100KC931
1/8W
LATCH HV
COMP NC
CS
VCC
GND OUT
L902
1
2
3
4
R912
1K 1/10W
C903 0.47UF
!
3
L901
C930
10N 50V
C915
0.047uF 50V
C900
0.001uF/250V
IC903
KIA431A-AT/P
0.45mH
NR901
NTCR 5 OHM 3A
C901
t
2
1U 25V
F901
FUSE
R903
!
1
CN901
SOCKET
R916
11.5KOHM +-1% 1/8W
Meridian 2
23
ZD801
ZD802
BZX79-B5V6
4
R803 4R7 1/8W 5%
3 G2 D2
2 S2 D2
R806 4R7 1/8W 5%
1 G1 D1
S1 D1
R805
BZX79-B5V6
5.1K 1/8W
5.1K 1/8W
5
6
7
8
Q801
R808
C804
CN801
CONN
C805
47N 50V
C806
R809
R804
FUSE
APM4548AKC
1
2
3
4
5
6
7
8
9
47N 50V
680uF 16V
C820
OVPT
C811
2.2U25V
C812
33N 50V
R820
+5V
20K 1/10W
D803
3
C
BAW56
R818
360R 1/10W 5%
C815
2.2U25V
C816
NC
ta9687GN-A-0-TR
C813
NC
8
7
6
5
4
3
2
1
R815
47K 1/4W
D801
1N4148
Q803
R816
5
6
7
8
Q802
+5V
10N 50V
1
2
C809
5pF/3KV
1
POWER X'FMR
PT802
R814
560R 1/10W 5%
100K 1/10W
1
C814
220P 50V
33N 50V
ISEN
0R051/8W
2
D802
BAV99
D804
3
R822
CN803
CONN
3.9nF 50V
OVPT
R821
1M 1/10W 5%
R811
100K 1/10W1K 1/8W
R817
BAV70
C819
R810
C810
R819
1M 1/10W 1% C818
1N 50V
P1
P1
2.2uF 25V
RK7002FD5T116
C817 G
CN802
CONN
3.9nF 50V
4
R812 4R7 1/8W 5%
3 G2 D2
2 S2 D2
R813 4R7 1/8W 5%
1 G1 D1
S1 D1
ISEN
NDR1
NDR2
PDR1
GNDP
VDDA
PDR2
TIMER
GNDA
PWM
RT1
ISEN
CT
OVPT SSTCMP
ENA
VSEN
C803
5pF/3KV
C807
APM4548AKC
9
10
11
12
13
14
15
16
1
2
1
POWER X'FMR
PT801
+5V
IC801
+12V
+12V
+12V
GND
GND
GND
+5V
DIM
ENA
L801
F801 FUSE
C814
100N 50V
22uH
C801
100N 50V
C802
100uF 50V
DIM
ENA
S2
G2
S1
G1
D2
D2
D1
D1
B360B
C803
Q801
1
2
3
4
8
7
6
5
C815
100N 50V
100N 50V
AO4828
R842
56K 1/10W
R845
NC
R804
56K1/10W
OVP1
R805
120KOHM 1/10W
R806
10K 1/10W 5%
C816
1N 50
1
1
1
1
OHM 1/10W
OHM 1/10W
OHM 1/10W
OHM 1/10W
C810
C812
C811
C813
NC
NC
NC
NC
R825
0R05 1/4W
R801
0.3 OHM +-5% 1/4
R833
R832
R831
R830
1
2
3
4
5
6
7
8
9
10
11
12
PWM STATUS
ISEN1
NC
ISEN2 SSTCMP
ISEN3
COMP
ISEN4
SEL
GNDA
VIN
ISEN8
GNDP
ISEN6
VREF
ISEN7
LDR
OVP
ISEN5
ISET
ISW
RT
ENA
24
23
22
21
20
19
18
17
16
15
14
13
IC801
TA9690GN
CN802
CONN
12
+14V
C804
ZD8014.7 uF 100V
10
9
8
7
6
5
4
3
2
1
C805
0.47uF 16V
11
11
10
9
8
7
6
5
4
3
2
1
Vout
73G253S 80 DN
R810
1K 1/10W 5%
C806
2U2 25V
R808
NC
R807
10 OHM 1/10W
C807
2.2U16V
R811
0R05 1/10W
R809
100K 1/10W 5%
CN803
CONN
12
CN801
CONN
R814
10 OHM 1/10W
R841
R840
R839
R838
R837
Vout
OVP2
OVP1
OHM 1/10W
OHM 1/10W
OHM 1/10W
OHM 1/10W
OHM 1/10W
R822
1M 1/10W 5%
R823
4.7KOHM +-5% 1/10W
1
1
1
1
1
R843
R815
56K 1/10W
56KOHM 1/10W
R824
43KOHM 1% 1/10W
OVP2
R816
120KOHM 1/16W
R817
10K 1/10W 5%
1
2
3
4
5
6
7
8
9
10
11
12
PWM STATUS
ISEN1
NC
ISEN2 SSTCMP
ISEN3
COMP
ISEN4
SEL
GNDA
VIN
ISEN8
GNDP
ISEN6
VREF
ISEN7
LDR
OVP
ISEN5
ISET
ISW
RT
ENA
IC802
TA9690GN
24
23
22
21
20
19
18
17
16
15
14
13
10
9
8
7
6
5
4
3
2
1
12
24 Meridian 2
6.4 Converter Board (715G3823P01000004L)
Remark: Parts position can be searched by using FIND function in PDF.
R821
10K 1/10W 5%
R820
100 OHM 1/10W
C808
0.47uF 16V
R803
1K 1/10W 5%
R818
NC
C809
2.2UF 16V
R819
100K 1/10W 5%
Meridian 2
6.5 Key Board (715G3807K0G000004S)
Remark: Parts position can be searched by using FIND function in PDF.
VCC
C001
1000pF 50V
C002
10uF 6.3V
GP0[4]
CSInt
GP0[3]
VDD
1
2
3
4
GP0[0]
GP0[1]
I2C SCL
I2C SDA
GP0[2]
XRES
GP1[4]
GP1[3]
12
11
10
9
Button_4
Button_5
Button_1
INPUT
T01
Button_2
Power
T02
Button_3
LEFT
T03
Button_4
MENU
T04
Button_5
RIGHT
T05
GP1[0]
GP1[1]
VSS
GP1[2]
LED_Blue
LED_Amber
I2C_SCL
I2C_SDA
Buttons
16
15
14
13
U001
C003
100N 50V
Button_3
Button_1
Button_2
5
6
7
8
CY 8C20180-LDX2I
CN001
CONN
7
MENU
I2C_SCL
I2C_SDA
LED_Vcc
VCC
LEFT
RIGHT
INPUT
LED001
White
LED
R007
330 OHM 1/10W
CN401
CN001
KEY1
I2C SCL
KEY2
I2C SDA
POWER KEY#
LED VCC
LED G
VCC
LED R
GND
GND
NC
2
ZD004
NC/UDZSNP5.6B
1
ZD003
NC/UDZSNP5.6B
1
ZD002
NC/UDZSNP5.6B
1
ZD001
NC/UDZSNP5.6B
1
R006
220 OHM 1/10W 5%
Yellow
1
2
3
4
5
6
LED_Amber
LED_Blue
NC
POWER
25
Q604
R607
Q603
R606
Q701
C402
9
C401
41
C707
40
C709
41
6
C708
C626
C613
R617
C614
C615
C616
C704
40
U701
U702
R
L701
C705
40
R618
R608
R610
R609
C716
R605
C609
C623
C706
U101
U402
42
R113
C611
C617
R109
R108
FB102
C105
R114
FB103
R112
R117
C618
C612
R105
R111
R110
C109
R116
FB101
C113
R102
R107
R106
R101
R115
R103
C104
R104
C103
U704
R706
D601
C620
R621
C702
C722
U703
U103
U104
R431
R
41 3
R
42 5
5
1
43
42
R
41
R
43
42
8
R
42
C
42
R
42
C607
R602
R604
C608
R601
R603
C124
U105
U106
D101
13
7
R
9
11
R
9
41
R
3
41
0
13 1
R
13
8
R
12 9
R
12 6
R
12 7
R
12 2
R
13 4
R
13
R
6
10 2
C
10
C
0
11
L601
C710
R705
C714
C606
C610
R713
10
R704
FB604
11
FB601
C605
C723
C717
D602
R714
11
C621
U705
R139
U602
FB602
ZD702
8
U601
R
FB603
C720
13
FB701
C601
R
C622
C
R702
C719
11
C619
X401
U401
R301
R405
FB408
FB409
Q403
R404
CN102
R403
R414 R413
ZD101
CN101
10
R703
C718
CN602
C
R707
CN701
R708
26
Meridian 2
7. PCB Layout
CN301
C301
C302
R302
Meridian 2
FB104
Q402
R402
C408
D704
C407
FB401
C404
C417
R401
C412
R123
Q401
D703
R125
C711
C411
C414
D708
R303
C303
R307
R304
C304
C305
R615
C406
R308
C630
C603
CN702
D701
C116
Q302
FB605
R614
C604
C712
C713
R712
C602
40
R305
ZD603
R612
C405
FB703
R726
R135
R417
R133
FB404
R611
R306
Q301
R711
R613
R124
R616
U301
FB301
C117
C419
C410
FB402
C403
R436
C721
C415
U102
C422
R437
R438
R136
C1
18
D102
C115
C435
C434
ZD402
ZD403
ZD401
FB406
R439
CN402
41
C433
FB405
FB105
CN401
C432
R727
C715
C121
R622
R120
C119
U107
C120
FB106
C431
D707
C627
27
28 Meridian 2
7.2 Adapter Board (715G3980P0D0000030)
Remark: Parts position can be searched by using FIND function in PDF.
C911
C908
C919
C927
C918
C915 R919
R912
R922
R9
C901
R918
R916
R908
J901
D906
IC903
R914
J906
LED1
C920
11
C900
T901
IC902
D903
J904
D902
Q901
R941
JR901
R904
J902
C929
C925
R910
D908
R906
R934
R942
R940
C910
IC901
R939
L902
R901
J905
J903
BD901
C903
L901
VR901
F901
CN901
NR901
R937
R902
05
C907
C909
R907
R938
R9
C931
C930
R947
R903
L903
12V
Meridian 2
7.3 Inverter Board (715G3599P01000001S)
Remark: Parts position can be searched by using FIND function in PDF.
PT801
ZD801
J804
J808
CN802
D801
C803
J803
J802
J801
J805
CN801
J807
J811
PT802
J816
C809
ZD802
CN803
C806
J810
J809
F801
J813
R819
R809
Q803
R808
C817
C816
RJ802
C813
C807
R821
C812
R818
C814
R810
D804
R806
C819
Q801
C811
IC801
C815
C820
RJ803
R805
C804
R822
R813
RJ805
C805
Q802
R812
R815
C808
R807
R811
R803
C818
D803
J815
R804
R820
R816
RJ801
J814
C810
D802
R817
R814
29
30 Meridian 2
7.4 Converter Board (715G3823P01000004L)
Remark: Parts position can be searched by using FIND function in PDF.
R822
C804
C814
C803
R805
C815
R832
R831
R833
R806
R845
R808
R829
C816
R844
R809
R828
C806
R814
R812
R841
R840
R838
IC802
R837
R811
R818
R815
C809
R843
R826
R830
R839
R816
R825
CN802
R827
C805
R821
C807
R813
R807
R803
Q801
IC801
R817
R801
C802
R802
CN801
C801
ZD801
C813
C811
R804
R842
R810
C810
C812
L801
F801
R823
R824
R819 C808
R820
R836
R835
R834
CN803
Meridian 2
C001
R002
R007
R001
U001
R005
C002
ZD001
ZD002
ZD003
ZD004
C003
R004
CN001
R003
LED001
R006
31
32
Meridian 2
8. Wiring Diagram
Panel
CN402
CN802
CN301
Scaler Board
Key Board
CN801
CN001
CN401
CN102
CN101
CN702
CN701
Meridian 2
33
FFC
DC-DC
D-SUB EEPROM
Scaler IC
Flash EEPROM
DVI EEPROM
34
Meridian 2
Meridian 2
35
221EL2
36
Meridian 2
2. Remove the Inverter Board
221E2
Meridian 2
NG
OK
NG
Turn on the Power On/Off switch
OK
OK
NG
37
38
Meridian 2
NG
Replace the main board
OK
OK
The end
NG
OK
The end
NG
NG
Replace the key board
OK
Meridian 2
3. DIM
DIM (image overlap, focus or flicker)
OK
The end
NG
OK
The end
NG
OK
The end
NG
NG
NG
Replace the panel
OK
OK
Check the signal cable
and the PC
NG
OK
The end
39
40
Meridian 2
Color shift
Miss color
The end
NG
OK
NG
Meridian 2
Connect to
the PC LPT
41
42
Meridian 2
2. Select the Config item, and set the parameters as below picture:
OK
3. Select the Device item, and set the parameters as below picture:
Meridian 2
43
4. Select the Connect item, if it connect successfully, it will show Device Type is Pm25LV020, and then click
OK.
Note: The Device Type depends on the models.
5. Select the Read item, and then click Read to select the software.
44
Meridian 2
7. Select the Restore item, and select the Restore Enable to protect HDCP- KEY. The address must be set
0x03F000 which code will be protected from this address. And then set the protect range 4KB.
Meridian 2
8. Select the Auto item, and select the Restore Data.
45
46
Meridian 2
Note:
If the VGA is NG, please try to cut off the 5th pin of the VGA connector.
If the DVI is NG, please try to cut off the 14th pin of the DVI connector.
Meridian 2
47
48
Meridian 2
3. Double-click
,appear as follow:
Meridian 2
5. Click OK, it will show the picture as follow:
49
50
Meridian 2
7. Click Program, when the DDC Write complete, it will show the picture as follow:
8. Click ReadBoth, if the DDC Write is OK, it will show the picture as follow:
Meridian 2
221E2 EDID
Analog
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
----------------------------------------------00| 00 FF FF FF FF FF FF 00 41 0C 55 C0 94 BA 0A 00
10| 01 14 01 03 6C 30 1B 78 2E 35 85 A6 56 48 9A 24
20| 12 50 54 AF 6F 00 71 4F 81 40 81 80 95 00 A9 40
30| B3 00 D1 C0 01 01 02 3A 80 18 71 38 2D 40 58 2C
40| 45 00 DD 0C 11 00 00 1E 00 00 00 FF 00 30 30 30
50| 30 31 30 30 31 30 30 30 30 30 00 00 00 FD 00 38
60| 4C 1E 53 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70| 00 50 68 69 6C 69 70 73 20 32 32 31 45 0A 00 1E
EDID Structure Version/Revision: 01 03
C055
ID Serial Number:
703124
Week of Manufacture:
Year of Manufacture:
2010
48cm
27cm
Display Gamma:
2.2
Gx: 0.281
Bx: 0.143
Wx: 0.312
Ry: 0.339
Gy: 0.603
By: 0.070
Wy: 0.329
51
52
Meridian 2
800 x 600 @ 60Hz VESA
Extension Flag: 00
Block0 Checksum: 1E
Meridian 2
Digital
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
----------------------------------------------00| 00 FF FF FF FF FF FF 00 41 0C 55 C0 94 BA 0A 00
10| 01 14 01 03 80 30 1B 78 2E 35 85 A6 56 48 9A 24
20| 12 50 54 AF 6F 00 71 4F 81 40 81 80 95 00 A9 40
30| B3 00 D1 C0 01 01 02 3A 80 18 71 38 2D 40 58 2C
40| 45 00 DD 0C 11 00 00 1E 00 00 00 FF 00 30 30 30
50| 30 31 30 30 31 30 30 30 30 30 00 00 00 FD 00 38
60| 4C 1E 53 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70| 00 50 68 69 6C 69 70 73 20 32 32 31 45 0A 00 0A
EDID Structure Version/Revision: 01 03
C055
ID Serial Number:
703124
Week of Manufacture:
Year of Manufacture:
2010
48cm
27cm
Display Gamma:
2.2
Gx: 0.281
Bx: 0.143
Wx: 0.312
Ry: 0.339
Gy: 0.603
By: 0.070
Wy: 0.329
53
54
Meridian 2
Extension Flag: 00
Block0 Checksum: 0A
Meridian 2
221EL2 EDID
Analog
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
----------------------------------------------00| 00 FF FF FF FF FF FF 00 41 0C 56 C0 94 BA 0A 00
10| 01 14 01 03 6C 30 1B 78 2E 35 85 A6 56 48 9A 24
20| 12 50 54 AF 6F 00 81 40 81 80 95 00 A9 40 B3 00
30| D1 C0 71 4F 01 01 02 3A 80 18 71 38 2D 40 58 2C
40| 45 00 DD 0C 11 00 00 1E 00 00 00 FF 00 30 30 30
50| 30 31 30 30 31 30 30 30 30 30 00 00 00 FD 00 38
60| 4C 1E 53 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70| 00 50 68 69 6C 69 70 73 20 32 32 31 45 4C 00 DB
EDID Structure Version/Revision: 01 03
C056
ID Serial Number:
703124
Week of Manufacture:
Year of Manufacture:
2010
48cm
27cm
Display Gamma:
2.2
Gx: 0.281
Bx: 0.143
Wx: 0.313
Ry: 0.339
Gy: 0.603
By: 0.070
Wy: 0.329
55
56
Meridian 2
800 x 600 @ 60Hz VESA
Extension Flag: 00
Block0 Checksum: DB
Meridian 2
Digital
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
----------------------------------------------00| 00 FF FF FF FF FF FF 00 41 0C 56 C0 94 BA 0A 00
10| 01 14 01 03 80 30 1B 78 2E 35 85 A6 56 48 9A 24
20| 12 50 54 AF 6F 00 81 40 81 80 95 00 A9 40 B3 00
30| D1 C0 71 4F 01 01 02 3A 80 18 71 38 2D 40 58 2C
40| 45 00 DD 0C 11 00 00 1E 00 00 00 FF 00 30 30 30
50| 30 31 30 30 31 30 30 30 30 30 00 00 00 FD 00 38
60| 4C 1E 53 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70| 00 50 68 69 6C 69 70 73 20 32 32 31 45 4C 00 C7
EDID Structure Version/Revision: 01 03
C056
ID Serial Number:
703124
Week of Manufacture:
Year of Manufacture:
2010
48cm
27cm
Display Gamma:
2.2
Gx: 0.281
Bx: 0.143
Wx: 0.313
Ry: 0.339
Gy: 0.603
By: 0.070
Wy: 0.329
57
58
Meridian 2
Extension Flag: 00
Block0 Checksum: C7
Meridian 2
59
To PC Port 2
To PC LPT
To BSG-265A or
equivalent instrument
Philips
221E2/221EL2
3. Adjustment
Preparation before adjustment:
a. Monitor should be warmed up for more than half an hour.
b. Make sure that the tools are connected right and drive programs have been installed OK.
4. Adjustment process:
a. Press the power of CA-210, shut off the lens, press 0-Cal and open the lens after analyzer reset.
b. Open white balance adjustment program, select the right parameter according with the program and click OK.
c.
Make sure that the lens of CA-210 aims at the center of the screen, then click START to adjust.
d. After finish adjusting, the adjustment program displays pass, and the START button changes for NEXT, which
means that you can adjust another monitor.
60
Meridian 2
Meridian 2
61
62
Meridian 2
Location
PCM Codes
Description
Remark
FQ106
A34G1677AFLA8B0130
BEZEL
FQ004
KEPC9QPJ
E750
750GLC215A3S12M0PH
E750
750GLC215A3S12N000
E750
750GLC215A3S22M0PH
E750
750GLC215A3S22N000
E750
750GLU215H1754M0PH
E750
750GLU215H1754N000
E750
750GLU215H1764M0PH
E750
750GLU215H1764N000
FQ009
INPC9C22AAA5
FQ002
756GQACB PH019 00
CPT
FQ002
756GQACB PH020 00
AUO
FQ105
A34G1678AFLAIB0100
REAR COVER_21.5
CPT
FQ105
A34G1678AFLAMB0100
REAR COVER_21.5
AUO
FQ103
A34G1919AFL 1B0130
STAND-BASE ASSEY
FQ110
A37G0146 3
HINGE_ASM
E08902
089G 728HAA 2G
SIGNAL CABLE
FQ301
089G402A15N CX
FQ303
095G8018 3XH98
FQ405
A33G0797AFL 1L0100
KEY
U402
100GPMCI000NT1
MCU ASSY(056G1133129)
CPT
U402
100GPMAI002NT1
MCU ASSY(056G1133129)
AUO
X401
093G 22 53 J
14.31818MHZ/32PF/49US
U401
056G 562299
IC TSUMU58NWHL-LF-1 PQFP-100
U704
056G 563113
U705
056G 563215
U702
056G 563512
IC G1117-33T43UF TO-252
U103
056G 662502
U104
056G 662502
U105
056G 662502
U106
056G 662502
Meridian 2
U107
056G 662502
FQ010
ADPCA1236YQAX
IC902
056G 139 3A
IC PC123Y22FZ0F
T901
S80GL19P512V
TRANSFORMER ASSY
IC901
056G 379530
IC903
056G 158 12
KIA431A-AT/P TO-92
F901
084G 56 3 B
PT802
080GL19T 51 H
PT801
080GL19T 51 H
IC801
056G 608 12
IC ta9687GN-A-0-TR SOP-16
F801
084G 56 3 B
U001
056G 669 10
IC CG7246AM QFN-16(COL)
63
Location
PCM Codes
Description
FQ106
A34G1677AFLB8B0130
BEZEL
FQ004
KEPC9QPJ
E750
750GLU215H1614N000
E750
750GLU215H1624N000
FQ011
LNPCAB362AQD5
FQ002
756GQACB PH021 00
FQ105
A34G1678 GMBKK0100
REAR COVER_21.5
FQ103
A34G1919AFL 1B0130
STAND-BASE ASSEY
FQ110
A37G0146 3
HINGE_ASM
E08902
089G 728HAA 2G
SIGNAL CABLE
FQ301
089G404A15N IS
FQ303
095G8018 3XH98
FQ405
A33G0797AFL 1L0100
KEY
U402
100GPMAI001NT1
MCU ASSY(056G1133129)
X401
093G 22 53 J
14.31818MHZ/32PF/49US
U401
056G 562299
IC TSUMU58NWHL-LF-1 PQFP-100
U704
056G 563113
U705
056G 563215
U702
056G 563512
IC G1117-33T43UF TO-252
U103
056G 662502
Remark
64
Meridian 2
U104
056G 662502
U105
056G 662502
U106
056G 662502
U107
056G 662502
FQ010
ADPC91236YA1
IC902
056G 139 3A
IC PC123Y22FZ0F
T901
080GL19P512 S
IC901
056G 379530
IC903
056G 158 12
KIA431A-AT/P TO-92
F901
084G 56 3 B
U001
056G 669 10
IC CG7246AM QFN-16(COL)
PCM Codes
Description
E08902
089G 728CAA 2G
SIGNAL CABLE
E08902
089G 728HAA 2G
SIGNAL CABLE
FQ301
089G414A15N IS
E09504
095G176J 10532
E09505
095G176J 10533
E09504
095G176W 10532
E09505
095G176W 10533
E09502
095G8014 7D942
E09502
095G8014 7W942
FQ303
095G8018 3XH98
E09503
095G802210D508
E09503
095G802210W508
E750
750GLU215H1614N000
E750
750GLU215H1624N000
FQ405
A33G0797AFL 1L0100
KEY
FQ106
A34G1677AFLB8B0130
BEZEL L215WA-TU8-TUS8
FQ105
A34G1678AFLAKB0100
REAR Cover_21.5
FQ103
A34G1919AFL 1B0130
STAND-BASE ASSEY
FQ110
A37G0146 3
HINGE_ASM
FQ201
Q40G 22E813 5A
RATING LABEL
Meridian 2
FQ206
Q41G78S181313A
FQ205
705GQACS007
CUSHION ASSY
FQ202
Q44GB026813 4A
FQ203
Q45G 88609197
EPE BAG
FQ204
Q70G22C1813 4A
FQ201
Q40G 22E813 6A
RATING LABEL
FQ010
ADPCA1236YQAX
IC902
056G 139 3A
IC PC123Y22FZ0F
NR901
061G 58005 W
R904
061G152M47852T
C903
063G107M47410M
C909
C900
065G306M1022B2
1000pf 400vac/250vac y1
C919
067G 515681 4L
C918
067G 515681 4L
C918
067G215C5614NV
C919
067G215C5614NV
C918
067G215C5614RV
C919
067G215C5614RV
C927
067G215V101 4R
C907
067G515Z82015L
C907
067G515Z82015N
D902
071G 55 30
D903
071G 55 30
L902
073G 174514 H
L902
073G 174514 S
L901
073G 174515 H
L901
073G 174515 S
L903
073G 253902 H
L903
073G 253902 S
T901
080GL19P512 H
T901
080GL19P512 S
LED1
081G
2 3 1P
E08906
089G 171535 G
DC CABLE 1000MM
E08906
089G 171536 C
DC CABLE 1200MM
65
66
Meridian 2
E08906
089G 171536 G
DC CABLE 1200MM
E08906
089G 171536 H
DC CABLE 1200MM
BD901
093G 50460514
D903
093G 52 1552T
D903
093G 5212T52T
D902
093G 5212T52T
T901
S80GL19P512V
Transformer ASSY
D906
093G 60226
STPS20H100CT
D906
093G 60228
D906
093G 605AP
Diode MBR20100CT
HS1
Q90G0201 1
HEAT SINK
Q901
057G 667 21
STP10NK70ZFP
Q901
057G 667924
MOSFET SMK0965F
HS1
Q90G0200 1
HEAT SINK
CN901
087G 50112A CJ
AC SOCKET
CN901
087G 50112A DL
AC SOCKET 3PIN
IC901
056G 379530
R912
061G0603102 JF
R911
061G0603202 JT
R918
061G0603203 JT
R940
061G0603221 JF
R919
061G06034532FF
R905
061G08051002FF
R905
061G08051002FY
R903
061G08051004FF
R903
061G08051004FT
R942
061G0805101 JY
R910
061G0805104 JT
R916
061G08051152FT
R941
061G0805159 JT
R922
061G0805471 JT
JR901
061G1206000 7
R908
061G1206101 JT
R914
061G1206101 JT
R906
061G1206103 JT
Meridian 2
R934
061G1206103 JT
R902
061G1206105 JF
R901
061G1206105 JF
R938
061G1206564 JF
R937
061G1206564 JF
R907
061G1206564 JF
C930
065G060310332K
C915
065G060347332K
C915
065G060347332K
C931
065G080510131J
C931
065G080510131J
C931
065G080510131J
C910
065G080510432K
C901
065G080510522K
C920
065G080510522K
C911
065G120622272K
C908
065G120622272K
D908
093G 64S522SEM
LL4148
CN901
006G 31500
EYELET
12V
006G 31501
EYELET
GND
006G 31501
EYELET
12V
006G 31501
EYELET
NR901
006G 31502
1.5MM RIVET
L902
006G 31502
1.5MM RIVET
L901
006G 31502
1.5MM RIVET
C907
006G 31502
1.5MM RIVET
C903
006G 31502
1.5MM RIVET
IC903
056G 158 12
KIA431A-AT/P TO-92
R947
061G 60210052T XZ
C925
C929
067G 2154707NT
KY50VB47M-TP5 6.3*11
FB901
071G 55908
F901
084G 56 3 B
FQ002
CBPC9ANPHQJ
100GPMAI001NT1
MCU ASSY(056G1133129)
U402
67
68
Meridian 2
C718
067G204V181 3K
C716
067G204V471 2K
FB701
071G 55 26 S
FERRITE CORE
CN701
088G 304 11 C
CN101
088G 35315FVDL
CN101
088G 35315FVXH
CN102
088G 35424F VC
X401
093G 22 53 J
14.31818MHZ/32PF/49US
CN402
033G8032 4F X
WAFER 4P 1.25MM
CN402
033G8032 4F HR
CONNECTOR
CN401
033G8032 7F X
CN401
033G8032 7F HR
CONNECTOR
CN702
033G803210F HR
CONNECTOR
U401
056G 562299
IC TSUMU58NWHL-LF-1 PQFP-100
U704
056G 563113
U705
056G 563215
U702
056G 563512
IC G1117-33T43UF TO-252
U105
056G 662502
U106
056G 662502
U107
056G 662502
U104
056G 662502
U103
056G 662502
U105
056G 662505
U106
056G 662505
U107
056G 662505
U104
056G 662505
U103
056G 662505
U101
056G1133 34
M24C02-WMN6TP
U102
056G1133 34
M24C02-WMN6TP
U402
056G1133129
U101
056G1133918
IC AT24C02BN-SH-T 8-SOIC
U102
056G1133918
IC AT24C02BN-SH-T 8-SOIC
Q402
057G 417517
Q403
057G 417517
Q302
057G 417518
Meridian 2
Q401
057G 417518
Q701
057G 417518
Q301
057G 763 1
R414
061G0402000 JY
R423
061G0402000 JY
R131
061G0402100 JF
R132
061G0402100 JF
R134
061G0402100 JF
R130
061G0402100 JF
R129
061G0402100 JF
R128
061G0402100 JF
R127
061G0402100 JF
R126
061G0402100 JF
R115
061G0402100 JF
R111
061G0402100 JF
R105
061G0402100 JF
R134
061G0402100 JY
R132
061G0402100 JY
R131
061G0402100 JY
R130
061G0402100 JY
R129
061G0402100 JY
R128
061G0402100 JY
R127
061G0402100 JY
R126
061G0402100 JY
R115
061G0402100 JY
R111
061G0402100 JY
R105
061G0402100 JY
R706
061G0402101 JF
R437
061G0402101 JF
R436
061G0402101 JF
R428
061G0402101 JF
R417
061G0402101 JF
R416
061G0402101 JF
R415
061G0402101 JF
R409
061G0402101 JF
69
70
Meridian 2
R119
061G0402101 JF
R118
061G0402101 JF
R113
061G0402101 JF
R101
061G0402101 JF
R706
061G0402101 JY
R437
061G0402101 JY
R436
061G0402101 JY
R428
061G0402101 JY
R417
061G0402101 JY
R416
061G0402101 JY
R415
061G0402101 JY
R409
061G0402101 JY
R119
061G0402101 JY
R118
061G0402101 JY
R113
061G0402101 JY
R101
061G0402101 JY
R104
061G0402102 JF
R103
061G0402102 JF
R103
061G0402102 JY
R104
061G0402102 JY
R702
061G0402103 JF
R703
061G0402103 JF
R705
061G0402103 JF
R439
061G0402103 JF
R438
061G0402103 JF
R419
061G0402103 JF
R412
061G0402103 JF
R407
061G0402103 JF
R308
061G0402103 JF
R305
061G0402103 JF
R136
061G0402103 JF
R135
061G0402103 JF
R133
061G0402103 JF
R123
061G0402103 JF
R120
061G0402103 JF
Meridian 2
R308
061G0402103 JY
R407
061G0402103 JY
R412
061G0402103 JY
R419
061G0402103 JY
R438
061G0402103 JY
R439
061G0402103 JY
R702
061G0402103 JY
R703
061G0402103 JY
R705
061G0402103 JY
R305
061G0402103 JY
R136
061G0402103 JY
R135
061G0402103 JY
R133
061G0402103 JY
R123
061G0402103 JY
R120
061G0402103 JY
R421
061G0402104 JF
R726
061G0402104 JY
R712
061G0402104 JY
R421
061G0402104 JY
R306
061G0402104 JY
R714
061G04021301FT
R714
061G04021301FY
R727
061G0402184 JY
R106
061G0402222 JF
R107
061G0402222 JF
R402
061G0402222 JF
R106
061G0402222 JT
R107
061G0402222 JT
R106
061G0402222 JY
R107
061G0402222 JY
R402
061G0402222 JY
R304
061G0402223 JY
R406
061G0402223 JY
R704
061G0402223 JY
R711
061G0402333 JF
71
72
Meridian 2
R711
061G0402333 JY
R401
061G04023900FY
R433
061G04023901FY
R432
061G04023901FY
R110
061G0402470 JF
R109
061G0402470 JF
R110
061G0402470 JT
R109
061G0402470 JT
R109
061G0402470 JY
R114
061G0402470 JY
R117
061G0402470 JY
R110
061G0402471 JY
R420
061G0402472 JF
R404
061G0402472 JF
R303
061G0402472 JF
R138
061G0402472 JF
R137
061G0402472 JF
R125
061G0402472 JF
R124
061G0402472 JF
R420
061G0402472 JY
R404
061G0402472 JY
R303
061G0402472 JY
R138
061G0402472 JY
R137
061G0402472 JY
R125
061G0402472 JY
R124
061G0402472 JY
R713
061G04026801FY
R139
061G0402682 JY
R116
061G0402750 JY
R112
061G0402750 JY
R108
061G0402750 JY
R102
061G0603000 JF
R403
061G0603000 JF
R405
061G0603000 JF
R707
061G0603000 JF
Meridian 2
R707
061G0603000 JY
R405
061G0603000 JY
R403
061G0603000 JY
R102
061G0603000 JY
FB703
061G0603000 JY
R301
061G1206221 JF
R302
061G1206221 JF
C107
065G040210232K
C118
065G040210232K
C119
065G040210232K
C120
065G040210232K
C121
065G040210232K
C710
065G040210232K
C710
065G040210232K
C714
065G040210232K
C412
065G040210412K
C413
065G040210412K
C414
065G040210412K
C415
065G040210412K
C416
065G040210412K
C417
065G040210412K
C422
065G040210412K
C431
065G040210412K
C432
065G040210412K
C702
065G040210412K
C705
065G040210412K
C706
065G040210412K
C708
065G040210412K
C721
065G040210412K
C717
065G040210412K
C709
065G040210412K
C115
065G040210412K
C124
065G040210412K
C301
065G040210412K
C304
065G040210412K
73
74
Meridian 2
C403
065G040210412K
C404
065G040210412K
C405
065G040210412K
C406
065G040210412K
C407
065G040210412K
C408
065G040210412K
C409
065G040210412K
C410
065G040210412K
C411
065G040210412K
C431
065G040210412K
C422
065G040210412K
C417
065G040210412K
C416
065G040210412K
C415
065G040210412K
C414
065G040210412K
C413
065G040210412K
C412
065G040210412K
C432
065G040210412K
C702
065G040210412K
C705
065G040210412K
C706
065G040210412K
C708
065G040210412K
C709
065G040210412K
C717
065G040210412K
C721
065G040210412K
C115
065G040210412K
C124
065G040210412K
C301
065G040210412K
C304
065G040210412K
C403
065G040210412K
C404
065G040210412K
C405
065G040210412K
C406
065G040210412K
C407
065G040210412K
C408
065G040210412K
Meridian 2
C409
065G040210412K
C410
065G040210412K
C411
065G040210412K
C719
065G040210427Z
C713
065G040210427Z
C712
065G040210427Z
C722
065G040215131J
C103
065G040222031J
C104
065G040222031J
C303
065G040222415K
C117
065G040222415K
C116
065G040222415K
C401
065G040222417Z
C420
065G040247031J
C421
065G040247031J
C110
065G040247312K
C111
065G040247312K
C114
065G040247312K
C108
065G040247312K
C106
065G040247312K
C102
065G040247312K
C102
065G040247312K
C106
065G040247312K
C108
065G040247312K
C110
065G040247312K
C111
065G040247312K
C114
065G040247312K
C113
065G040250931J
C109
065G040250931J
C105
065G040250931J
C711
065G060310232K
C715
065G060310232K
C305
065G060310512K
C419
065G0805106A7Z
C402
065G0805106A7Z
75
76
Meridian 2
C723
065G120610625K
C720
065G120610625K
C302
065G120622615K
C704
065G120622615K
C707
065G120622615K
C707
065G120622615K
C704
065G120622615K
C302
065G120622615K
FB301
071G 56K121
CHIP BEAD
FB408
071G 56K121
CHIP BEAD
FB404
071G 56V301 B
FB401
071G 56V301 B
FB402
071G 56V301 B
FB406
071G 59A121 TA
FB405
071G 59A121 TA
FB104
071G 59G301
FB105
071G 59G301
FB106
071G 59G301
FB101
071G 59K190 B
19 OHM BEAD
FB102
071G 59K190 B
19 OHM BEAD
FB103
071G 59K190 B
19 OHM BEAD
L701
073G253S521 H
D102
093G 64 42 L
D101
093G 64 42 L
D101
093G 64 42 PP
BAV70 SOT-23
D102
093G 64 42 PP
BAV70 SOT-23
ZD101
093G 39GA01 T
RLZ5.6B
D708
093G3004 3
SM340A
D707
093G3004 3
SM340A
D704
093G3004 3
SM340A
D703
093G3004 3
SM340A
D701
093G3004 3
SM340A
CN301
311GW125A30ACH
FQ004
KEPC9QPJ
CN001
033G8032 6F S HR
CONNECTOR
Meridian 2
U001
056G 665 43
IC CY8C20180-LDX2I QFN-16(COL)
U001
056G 669 10
IC CG7246AM QFN-16(COL)
R007
061G0603153 JT
R005
061G0603561 JY
R004
061G0603561 JY
R003
061G0603561 JY
R002
061G0603561 JY
R001
061G0603561 JY
C001
065G060310231J
C003
065G060310437Z
C002
065G060310605M
C002
065G060310605M
LED001
081G 14 30 EL
ZD001
093G 39S 34 T
UDZSNP5.6B ROHM
ZD002
093G 39S 34 T
UDZSNP5.6B ROHM
ZD003
093G 39S 34 T
UDZSNP5.6B ROHM
ZD004
093G 39S 34 T
UDZSNP5.6B ROHM
FQ011
LNPCAB362AQD5
C802
067G 4151017KV
C804
067G 4151017KV
C802
067G 4151017LV
C804
067G 4151017LV
CN802
033G801910Y H
CN803
033G801910Y H
CN801
033G803210F HR
CONNECTOR
IC801
056G 379167
IC TA9690GN-A1-0-TR SOP-24
IC802
056G 379167
IC TA9690GN-A1-0-TR SOP-24
Q801
057G 763 6
R811
061G0603000 JT
R807
061G0603100 JF
R814
061G0603100 JF
R844
061G0603100 JF
R812
061G0603101 JY
R820
061G0603101 JY
R810
061G0603102 JT
77
78
Meridian 2
R803
061G0603102 JT
R806
061G0603103 JT
R813
061G0603103 JT
R817
061G0603103 JT
R821
061G0603103 JT
R809
061G0603104 JT
R819
061G0603104 JT
R822
061G0603105 JT
R841
061G0603109 JY
R840
061G0603109 JY
R839
061G0603109 JY
R838
061G0603109 JY
R837
061G0603109 JY
R836
061G0603109 JY
R835
061G0603109 JY
R834
061G0603109 JY
R833
061G0603109 JY
R826
061G0603109 JY
R827
061G0603109 JY
R828
061G0603109 JY
R829
061G0603109 JY
R830
061G0603109 JY
R831
061G0603109 JY
R832
061G0603109 JY
R805
061G0603124 JY
R816
061G0603124 JY
R824
061G06034302FT
R823
061G0603472 JY
R804
061G06035602FF
R843
061G06035602FF
R842
061G06035602FF
R815
061G06035602FF
R825
061G1206000 JF
F801
061G12060004JF
R801
061G1206308 JF
Meridian 2
C816
065G060310232K
C805
065G060347412K
C808
065G060347412K
C801
065G080510432K
C803
065G080510432K
C809
065G080522512K
C807
065G080522512K
C806
065G080522525K
L801
073G253S 80 H
L801
073G253S 80 DN
ZD801
093G 60S 31 T
R802
061G1206308 JF
Service Kit
Description
Part No.
EDID KIT
715GT034-B
715GT039-A
Picture
79
80
Meridian 2
221E2SB/27
Location
PCM Codes
Description
Location
PCM Codes
Description
FQ301
089G404A15N CX
FQ301
089G402A15N CX
PCM Codes
221E2SB/27
Description
Location
PCM Codes
Description
PCM Codes
221E2SB/27
Description
Location
PCM Codes
Description
PCM Codes
089G410A15N CX
221E2SB/27
Description
Location
PCM Codes
Description
FQ301
089G402A15N CX
Meridian 2
Diversity of 221E2SB/71 compared with 221E2SB/27
221E2SB/71
Location
PCM Codes
221E2SB/27
Description
Location
PCM Codes
Description
PCM Codes
221E2SB/27
Description
Location
PCM Codes
Description
PCM Codes
221E2SB/27
Description
089G412A15NIS3
Location
FQ301
PCM Codes
089G402A15N CX
Description
AC POWER CORD 1500MM AMERICA REG.
221E2SB/27
Location
PCM Codes
Description
Location
PCM Codes
Description
FQ301
089G417A15N IS
FQ301
089G402A15N CX
81
82
Meridian 2
PCM Codes
221E2SB/27
Description
Location
PCM Codes
Description
AC POWER CORD 1500MM
AMERICA REG.
SCALER BOARD
ASSY(CBPC9ANPHQJ)
FQ301
089G420A15N IS
FQ301
089G402A15N CX
FQ002
756GQACB PH028 00
FQ002
756GQACB PH019 00
100GPMCI001NT1
MCU ASSY(056G1133129)
U402
100GPMCI000NT1
MCU ASSY(056G1133129)
A34G1678AFLAHB0100
FQ105
A34G1678AFLAIB0100
REAR COVER_21.5
756GQACB PH027 00
FQ002
756GQACB PH020 00
SCALER BOARD
ASSY(CBPC9ANPHQJ)
100GPMCI001NT1
MCU ASSY(056G1133129)
U402
100GPMAI002NT1
MCU ASSY(056G1133129)
A34G1678AFLALB0100
FQ105
A34G1678AFLAMB0100
REAR COVER_21.5
U402
FQ105
FQ002
U402
FQ105
PCM Codes
221EL2SB/00
Description
Location
PCM Codes
Description
PCM Codes
221EL2SB/00
Description
Location
PCM Codes
Description
Meridian 2
Diversity of 221EL2SB/69 compared with 221EL2SB/00
221EL2SB/69
Location
FQ301
PCM Codes
089G410A15N IS
221EL2SB/00
Description
Location
PCM Codes
Description
FQ301
089G404A15N IS
PCM Codes
221EL2SB/00
Description
Location
PCM Codes
Description
PCM Codes
221EL2SB/00
Description
Location
PCM Codes
Description
83
84
Meridian 2
Meridian 2
CONTENTS
1. Foreword
2. Product Profile
2.1 EDID Header
2.2 Panel Spec
2.3 Scanning Frequencies
2.4 Ambient Temperature
3. Electrical Characteristics
3.1 Interface Signals
3.2 Interface
3.3 Timing Requirement
3.4 Horizontal Scanning
3.5 Vertical Scanning
3.6 Power Input Connection
3.7 Power management
3.8 VGA Display Identification
3.9 DVI-D Display Identification
3.10 DDC/CI Support and Smart Manage/Control
3.11 Hot-key Definition
3.12 Smart Contrast
3.13 Smart Image Lite
4. Visual Characteristics
4.1 Test Conditions
4.2 Brightness
4.3 Image Size
4.4 Brightness Uniformity
4.5 Check Cross Talk (S)
4.6 White Color Adjustment
5. Mechanical Characteristics
5.1 Cosmetic
5.2 Mechanical Data Files
5.3 Location of Philips Logo
5.4 Gap between Panel and Front Bezel
5.5 Location Control Icons
5.6 Color for Resin/Paint
5.7 Fire Enclosure Request
5.8 Resins
5.9 If Paint is used
5.10 Plastic Mold Tooling
5.11 Plastics Flammability
85
86
Meridian 2
Meridian 2
87
1. Foreword
This specification describes a 21.5 FHD multi-scan color TFT LCD monitor with maximum resolution up to 1920
x 1080 /60Hz non-interlaced.
All optical characteristics (including White-D, Brightness, and so on) are determined according to panel
specification after warming up approximate 30 minutes that brightness stability is optimal, and follow strictly after
panel specification.
2. Product Profile
This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated
tilt base.
2.1 EDID header
Data for EDID & .inf file
1
2
3
4
5
6
7
maximum resolution
Horizontal Frequency Range
Vertical Frequency Range
Monitor Name (13 characters max.)
2.2 LCD
Suppliers to offer panel specifications.
Panel incoming specification: Follow Philips specification.
SEC (1st source)
Type NR.
Resolution
Outside dimensions
Pitch (mm)
Color pixel arrangement
Display surface
Color depth
Backlight
Active area (W x H)
View angle (CR=10)
Contrast ratio
White luminance
Color gamut
Gate IC
Source IC
Response time
Vertical frequency range
88
Meridian 2
Outside dimensions
Pitch (mm)
Color pixel arrangement
Display surface
Color depth
Backlight
Active area (W x H)
View angle (CR=10)
Contrast ratio
White luminance
Color gamut
Gate IC
Source IC
Response time
Vertical frequency range
AUO (2nd source)
Type NR.
Resolution
Outside dimensions
Pitch (mm)
Color pixel arrangement
Display surface
Color depth
Backlight
Active area (W x H)
View angle (CR=10)
Contrast ratio
White luminance
Color gamut
Gate IC
Source IC
Response time
Vertical frequency range
Meridian 2
2.4 Ambient temperature:
0 C - 40 C
3. Electrical Characteristics
3.1 Interface signals
a). D-Sub Analog
Input signal : Video, Hsync, Vsync
Video
: 0.7 Vp-p, input impedance, 75 ohm @DC
Sync.
: Separate sync
TTL level, input impedance 2.2k ohm terminate
Hsync:
Positive/Negative
Vsync :
Positive/Negative
Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative)
Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)
b). DVI-D Digital
Input signal: Single TMDS link (Three channels: RX0-/+, RX1-/+, RX2-/+)
c). Audio (Not required in 221E2)
Input signal: 1000 mVrms
Loudspeaker (Impedance: 5.25 Ohm +/-15%): 1.5W+1.5W stereo for RMS Power
Frequency range: 450Hz - 20 KHz
Headphone connection will mute speakers
Pin assignments:
1
10
11
Pin
1
2
3
4
5
6
7
8
Signal Assignment
Red video
Green video
Blue video
Ground
Cable Detected
Red Ground
Green Ground
Blue Ground
15
Pin
9
10
11
12
13
14
15
Signal Assignment
PC5V (+5 volt power)
Sync Ground
Ground
SDA
H-Sync (or H+V)
V-sync
SCL
89
90
Meridian 2
3.2.2 DVI Cable
The input signals are applied to the display through DVI-D cable.
Length
: 1.5 M +/- 50 mm
Connector type : DVI-D male with DDC-2B pin assignments
White connector thumb-operated jackscrews
With transplant pin protective cover.
Pin Assignment:
Pin
Signal Assignment
Pin
Signal Assignment
TMDS RX2-
13
Floating
TMDS RX2+
14
+5V Power
TMDS Ground
15
Ground
Floating
16
Floating
17
TMDS RX0-
DDC Clock
18
TMDS RX0+
DDC Data
19
TMDS Ground
Floating
20
Floating
TMDS RX1-
21
Floating
10
TMDS RX1+
22
TMDS Ground
11
TMDS Ground
23
TMDS Clock+
12
Floating
24
TMDS Clock-c
Meridian 2
3.3.1 Mode storing capacity
Factory preset modes
Preset modes
User modes
91
: 12
: 46
: 10
OSD DEFINITIONS
OSD LANGUAGES
OSD TREE
M2 OSD Button
definition _ 20100120
221E2 OSD
TREE-100309.xls
POWER ON LOGO
3.3.4
1920x1080_new.
zip
92
Meridian 2
: Positive or Negative
: 30 - 83 K Hz
: Positive or Negative
: 56 - 76 Hz
: 1.5 M
: 3 leads power cord with protective earth plug.
Hsync
Vsync
Video
Power-On
On
On
active
Power Saving
Off
Off
blanked
DC Power Off
N/A
Pwr-cons.
Indication
Rec. time
< 33 W(max)
White LED
EPA5.0 : 31.6
Blinking white LED
< 0.8W
Period 3ec on, 3sec off
< 0.5W
--
LED Off
HOT KEY.xls
Meridian 2
93
94
Meridian 2
then go back. The setting in main OSD will show preset values of that SmartImage profile enabled.
Profile Definitions (system integrators to input at design stages)
A. Standard
i. Purpose: Default out of box settings, No optimization by SmartImage.
ii. Design:
1. This will follow user OSD setting. If any change by user, it will be saved. When switch back
from other SmartImage profiles, it will go back to last saved setting.
2. Default out of box settings
3. Same as OFF mode settings in SmartImage
B. Internet
i. Purpose: Design for Internet application, especially web browsing.
The screen is mixed by text & picture. Desktop publish could use this profile also.
ii. Enhancement Point:
1. The enhancement will be mostly based on the "Image viewing" settings that are also under
definition, made milder by the higher probability of strong compression typical of the Internet
photos and clips.
2. Color temperature should be 6500 K
3. Brightness level should be around 90%
4. SmartResponse set to Low.
5. Smart Contrast set to Off
C. Game
i. Purpose: Design for PC game software and game boxes, e.g. PS3 and Xbox. The screen is
dominated by artificial animation with rich color.
ii. Enhancement Point:
1. Dynamic contrast enhancement by histogram analysis should be implemented.
2. Sharpness enhanced 90%.
3. Color enhancement set as the same with Video.
4. Color temperature set to panel native(original color temp)
5. Brightness level sets to maximum.
6. SmartResponse set to High
7. Gamma Table turns off to achieve fastest response time.
8. SmartContrast set to On
Demo mode
A. Purpose: Built-in demo mode for sales in-store demo.
B. Design:
i. Dynamically split screen to 2 vertical frames with one vertical white line. The line width is 2
pixels. The left frame will be enhanced by SmartImage Lite and right frame remains original
performance.
ii. There is OSD showing SmartImage Lite & SmartResponse Demonstration in left frame and
Original Image in right frame.
iii. The OSD word color is white with transparent background.
iv. The demo profile will be Video Playback profile with High ODC setting.
v. The current SmartContrast value also is shown on the bottom of the screen.
C. Hot keys to trigger:
Press [Smart Image] 3 seconds or more to trigger the demo mode.
When demo mode is on, press 3 seconds or more to turn off the demo mode
Meridian 2
95
4. Visual Characteristics
4.1 Test conditions
Unless otherwise specified, this specification is defined under the following conditions.
(1) Input signal: As defined in 3.3, 1920 x 1080 non-interlaced mode (1920 x 1080@60Hz 148.5MHz),
signal sources must have 75 ohm output impedance.
(2) Luminance setting: controls to be set to 250 nits with full screen 100 % duty cycle white signal
(3) Warm up: more than 30 minutes after power on with signal supplied.
(4) Ambient light: 400 -- 600 lux.
5) Ambient temperature: 20 5 C
4.2 Brightness
Follow Panel specification.
4.3 Image size
Actual display size 476.64 (H) x 268.11 (V) mm
4.4 Brightness uniformity
Set contrast at 100% and turn the brightness to get average above 250 nits at centre of the screen.
Apply the Fig 1; it should comply with the following formula:
( B_max - B_min )
X 100% > 75%
B_max
Where B_max = Maximum brightness
B_min = Minimum brightness
4.5 Check Cross talk (S)
Apply Pattern 2. Set contrast and brightness at 100 %.
Measure YA. Then output Pattern 3 and measure YB.
The cross talk value:
ABS (YA - YB)
X 100% <
YA
1.5 %
(x,y)
9300K
6500K/sRGB
sRGB
96
Meridian 2
(x,y)
9300K
6500K/sRGB
sRGB
(x,y)
9300K
6500K/sRGB
sRGB
5. Mechanical Characteristics
5.1 Cosmetic Philips ID
5.2 Mechanical data files ProE files required
5.3 Location of Philips logo Per Philips make-up sheet
5.4 Gap between panel and front bezel
< 1.2mm (typ.)
5.5 Location of Control icons Per Philips Graphic sheet
5.6 Color for resin/paint Per Philips make-up sheet
5.7 Fire enclosure request
Shielding Cover should fulfill international standard
5.8 Resins
RoHS required
WEEE required.
Resin type/selection refers to Project Book Section 7.2 Plastic material.
5.9 If paint is used
RoHS required
WEEE require
If new painting type needs to implement, refer to UN-D 1235.
Meridian 2
97
-5 +2/- 0 (forward)
+20 + 0/- 3 (backward)
nil
nil
nil
Swivel angle :
High Adjustment :
Portrait Display :
5.15 Label
Regulatory label / Carton label should follow Philips requirement.
China RoHS label
Detail document refer to Philips Engineering Reference Book.
5.16 Product dimension / Weight (Refer to Philips approved SHT 191/SHT560)
Unit dimension:
516.81mm (W) * 398.19 mm(H) * 199.91mm(D)
Packed unit dimension:
582 mm(W) * 452mm(H) * 140mm(D)
Net weight:
4.03 Kg
Gross weight:
5.23 Kg
5.17 Transportation
Transportation standards refer to UAN-D1534/00/01/02.
5.17.1 Transportation packages
Net weight Packaging and wrapping shall be sufficient to protect the product against damage
or loss during shipment from the supplier to the destination specified in the purchase order.
All packaging materials are subject to test and evaluation per UAN-D1534/00/01/02.
The cushion material shall be constructed using EPS material.
The doggy hole is requested.
98
Meridian 2
5.17.2 Transportation Test
Overall tests refer to UAN-D1534/00/01/02.
Vibration, drop test should be performed at ambient temperature (20C to 23oC) and relative
humidity (40% to 65%).
A. Transportation test specification for all regions
Package test
1. Random Vibration test
2. Drop test
3. Cold Drop test (for design reference)
Un-package test
1. Half sine shock test (non operation)
B. Transportation test specification for China/India
Package test
1. Random Vibration test
2. Drop test
3. Cold Drop test (for design reference)
Un-package test
1. Sine vibration (operating)
2. Half sine shock test (non operation)
750/1500/1800
630/1380/1564
660/1380/1564
6. Environmental Characteristics
The following sections define the interference and susceptibility condition limits that might occur between
external environment and the display device.
Meridian 2
6.1 Susceptibility of display to external environment
Operating
- Temperature:
0 to 35 degree C
- Humidity:
80% max
- Altitude:
0-3658 m
- Air pressure:
600-1100 mBAR
Storage
- Temperature:
- Humidity:
- Altitude:
- Air pressure:
-20 to 60 degree C
95% max
0-12192m
300-1100 mBAR
7. Reliability
7.1 Mean Time between Failures
System MTBF (Including the LCD panel and CCFL): 50,000 hrs
8. Quality Assurance Requirements
8.1 Acceptance test
According to MIL-STD-1916D
Control III level
AQL: NA
(Please also refer to annual quality agreement)
Customer acceptance criteria: UAW0377/00
9. PHILIPS FLAT PANEL MONITORS PIXEL DEFECT POLICY
Philips Flat Panel Monitors Pixel Defect Policy
BRIGHT DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
221E2
1 lit sub-pixel
15mm
99
100 Meridian 2
BLACK DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
221E2
1 dark sub-pixel
15mm
ACCEPTABLE LEVEL
221E2
5
Meridian 2
Fig 2: Cross talk pattern
Gray level 46 (64 Gray level)
1/6
1/2
YA
1/2
1/3
1/3
1/6
1/3
1/2
1/3
YB
1/2
1/3
101
102 Meridian 2
SEPARATE SYNC.
VIDEO
D
HORIZONTAL
VIDEO
R
VERTICAL
COMPOSITE SYNC.
VIDEO
C
HORIZONTAL
Meridian 2
103
WW_Regulatory.xls
104 Meridian 2
Safety Checks
After the original service problem has been corrected,a complete safety check
should be made. Be sure to check over the entire set, not just the areas
where you have worked. Some previous servicer may have left an unsafe
condition,which could be unknowingly passed on to your customer. Be sure
to check all of the following:
Fire and Shock Hazard
1. Be sure all components are positioned in such a way as to avoid the
possibility of adjacent component shorts. This is especially important
on those chassis which are transported to and from the service shop.
2. Never release a repaired unit unless all protective devices such as
insulators, barries, covers, strain reliefs, and other hardware have been
installed in accordance with the original design.
3. Soldering and wiring must be inspected to locate possible cold solder
joints,solder splashes,sharp solder points, frayed leads, pinched leads,
or damaged insulation ( including the ac cord).Be certain to remove
loose solder balls and all other loose foreign particles.
4. Check across-the-line components and other components for physical
evidence of damage or deterioration and replace if necessary. Follow
original layout,lead length, and dress.
5. No lead or component should touch a receiving tube or a resistor rated
at 1 watt or more. Lead tension around protruding metal surfaces or
edges must be avoided.
6. Critical components having special safety characteristics are identified
with ans by the Ref. No. in the parts list and enclosed within a broken line
* (where several critical components are grouped in one area) along with
the safety symbols on the schematic diagrams and/or exploded views.
7. When servicing any unit, always use a separate isolation transformer
for the chassis Failure to use a separate isolation transformer may
expose you to possible shock hazard, and may cause damage to
servicing instruments.
8. Many electronic products use a polarized ac line cord (one wide pin on
the plug.) Defeating this safety feature may create a potential hazard to
the service and the user. Extension cords which do not incorporate the
polarizing feature should never be used.
9. After reassembly of the unit, always perform an leakage test or resistance
test from the line cord to all exposed metal parts of the cabinet. Also check
all metal control shafts(with knobs removed), antenna terminals, handles,
screws, etc. to be sure the unit may be safety operated without danger of
electrical shock.
* Broken line
Implosion
1. All picture tubes used in current model receivers are equipped with an
integral implosion system. Care should always be used, and safety
glasses worn,whenever handling any picture tube. Avoid scratching or
otherwise damaging the picture tube during installation.
2. Use only replacement tubes specified by the manufacturer.
X-radiation
1. Be sure procedures and instructions to all your service personnel cover
the subject of X-radiation. Potential sources of X-rays in TV receivers are
the picture tube and the high voltage circuits. The basic precaution which
must be exercised is to keep the high voltage at the factory recommended
level.
2. To avoid possible exposure to X-radiation and electrical shock, only the
manufacturer's specified anode connectors must be used.
3. It is essential that the service technician has an accurate HV meter
available at all times. The calibration of this meter should be checked
periodically against a reference standard.
4. When the HV circuitry is operating properly there is no possibility of an xradiation problem. High voltage should always be kept at the manufacturer's
rated value-no higher - for optimum performance. Every time a color set is
serviced, the brightness should be run up and down while monitoring the
HV with a meter to be certain that the HV is regulated correctly and does
not exceed the specified value. We suggest that you and your technicians
review test procedures so that HV and HV regulation are always checked as
a standard servicing procedure, and the reason for this prudent routine is
clearly understood by everyone. It is important to use an accurate and
reliable HV meter. It is recommended that the HV recorded on each
customer's invoice, which will demonstrate a proper concern for the
customer's safety.
5. When troubleshooting and making test measurements in a receiver with
a problem of excessive high voltage, reduce the line voltage by means of
a Variac to bring the HV into acceptable limits while troubleshooting. Do
not operate the chassis longer than necessary to locate the cause of the
excessive HV.
TO
INSTRUMENTS
EXPOSED
METAL PARTS
0.15 uF
WATER
PIPE
EARTH
GROUND
WARNING : Before removing the CRT anode cap, turn the unit OFF and short the HIGH VOLTAGE to the CRT DAG ground.
SERVICE NOTE : The CRT DAG is not at chassis ground.