Escolar Documentos
Profissional Documentos
Cultura Documentos
Trade name
PROMATECT-200
Approval holder
Promat International NV
Bormstraat 24
B-2830 Tisselt
Belgium
Website
www.promat-international.com
from : to
use
of
ETA 07/0297
Manufacturing plant :
01
I. Legal bases
conditions
and
general
version,
no
Definition and
intended use
1.1
Scope
scope
of
product
and
1.2
1.2.1 General :
ETAG 018-1
reference
Type 3
Type 4
Type 5
Type 6
Type 7
Type 8
Type 9
Type 10
2.
2.1
2.2.2.2.1 General
The boards comply with all relevant European
and national provisions7 applicable for the uses
for which it is brought to the market.
In addition to this ETA clause relating to
dangerous substances, there may be other
requirements applicable to the products falling
within its scope (e.g. transposed European
legislation and national laws, regulations and
administrative provisions). In order to meet the
provisions of the EU Construction Products
Directive, these requirements need also to be
complied with, when and where they apply.
2.2.2.2.2 Release of formaldehyde
The boards have no formaldehyde containing
components.
2.2.3 Safety in Use
2.2.3.1 Flexural strength
In accordance with EN 12467, the boards have a
modulus of rupture (MOR) of 3 MPa (95%
confidence level).
2.2.7 Identification
3.
3.2
Responsibilities
3.1
Attestation of Conformity
3.2.1.1.1 General
The
ETA-holder
maintains
a
traceable
documentation of the production process from
purchasing or delivery of raw or basic raw
materials up to the storage and delivery of
finished products.
The factory production control system for the
product includes relevant design specifications,
including adequate drawings and written
instructions for:
- type and quality of all materials
- overall dimensions
- packaging and transport protection
The production control system specifies how the
control measures are carried out, and at which
frequencies.
Products that do not comply with requirements
as specified in the ETA are being separated from
the conforming products and marked as such.
The
ETA-holder
registers
non-compliant
production and action(-s) taken to prevent
further non-conformities. External complaints are
also being documented, as well as actions taken.
3.2.1.1.3 Maintenance,
equipment
calibration
of
testing
1 per week8
1 per week
1 per year
1 per year
1 per day10, per
dimension
1 per day, per
thickness
1 sample per n-boards
1 sample per n-boards
3.3
CE marking
4.1
Manufacturing
3.3.1 General
The CE marking shall be affixed to the board
packaging. In accordance with ETAG 018, the
required information to accompany the CE
symbol is:
a)
b)
c)
d)
e)
f)
g)
3.4
Installation
4.2.1 General
4.2.1.1 Supporting structure
The distance between supports shall be in
accordance with the information provided in the
assemblies described in annex 2.
4.2.1.2 Cutting and machining
The fire protective boards shall be cut and
machined using conventional woodworking
equipment. The use of saw blades with hardened
teeth or with tungsten carbide tipped blades is
recommended. When machining the fire
protective board with power tools, dust
extraction shall take place and inhalation of dust
should be avoided.
A safety data sheet is available from the
manufacturer upon request.
4.2.1.3 Joints
5.
Recommendations
5.1
ANNEX 1: References
ceilings
tests
for
ANNEX 2: Fire resistance performances and assembly methods for uses of boards covered by this ETA
Annex 2.0: Overview of fire resistance performances for PROMATECT -200 assemblies
The fire protective assemblies in Table A.2.0.1 have been assessed within the framework of this ETA.
Assemblies installed according to the provisions given in this annex are covered by this ETA.
Table A.2.0.1
Assembly
assessed within the framework of this ETA
Load-bearing steel beam, protected on
three sides by PROMATECT-200 fire
protective boards (thickness 15 mm)
Classification
according to
EN 13501-2
Test
standard
Intended use
type
according to
ETAG 018
Installation
details
Date of
addition
to this
ETA
R 90
EN 1365-3
Type 4
Annex 2.1
2008-0325
Annex 2.1: Specification of a load-bearing steel beam, protected on three sides by PROMATECT-200
fire protective boards (thickness 15 mm)
A.2.1.1
This annex was added to ETA 07/0297 on 2008-03-25. This assembly was not covered by this ETA prior to
the addition of this annex.
A 2.1.2
Classification
The assembly described in this Annex has been tested according to EN 1365-3:2001 and classified R 90
in accordance with EN 13501-2.
A.2.1.3
Installation requirements
Installation requirements in paragraph 4.2 of this ETA shall be taken into account.
A.2.1.4
Supporting structure
The steel beam with a width of 260 mm and a height of 260 mm (HEB 260) is supported by the
surrounding construction at a maximum span of 4500 mm and loaded with a static load of maximum
196,8 kN, applied in 2 points, each at 1/3 of the length of the beam, as shown in figure A.2.1.4.1.
Element
Beam
A.2.1.5
Identification
HEB 260 or equivalent
according to EN 10034
Table A.2.1.1
Characteristics
Width: 260 mm
Height: 260 mm
Insulation
None.
A.2.1.6
Any part of the beam exposed to fire shall be cladded by Promatect-200 boards with a thickness of
15 mm. Boards are cut to size and fixed together to form an encasement around the beam.
To fix the fire protective boards to the beam, Promatect -200 soldiers with a thickness of 20 mm are fit
between the flanges of the steel beam at 1200 mm centres. Dimensions of the soldiers are 100 mm x
ca. 227 mm.
The boards are fixed to the soldiers using staples with minimum dimensions (28/10,7/1,2) mm, placed at
maximum 100 mm centres. The boards are fixed to each other to form an encasement using staples
with minimum dimensions (38/10,7/1,2) mm, placed at maximum 100 mm centres.
Specifications for the components are given in Table A.2.1.2.
Element
Identification
Boards
Soldiers
Staples
Steel staples
to
prEN
equivalent
Steel staples
to
prEN
equivalent
Staples
A.2.1.7
according
14566
or
according
14566
or
Table A.2.1.2
Characteristics
(38/10,7/1,2) mm
Joints
Details
A.2.1.9 Figures
Figure A.2.1.9.1
Figure A.2.1.9.2
Key
Dimensions in mm.
1. Promatect-200 boards, thickness 15 mm
2. Promatect-200 soldiers, thickness 20 mm, width 100 mm, height ca. 227 mm, placed at 1200 mm
centres
3. Steel beam HEB 260
4. Steel staples ( 28/10,7/1,2) mm, placed at 100 mm centres
5. Steel staples ( 38/10,7/1,2) mm, placed at 100 mm centres.
Note
The span shown in figure A.2.1.9.1 is the maximum span for a static load of 196,84 kN, applied in
2 points at 1/3 of the length of the beam.
Alternative combinations of span and loading are considered equivalent if the resulting maximum
moments and shear forces do not exceed those corresponding with the configuration in
figure A.2.1.4.1, given an identical steel beam, identical applied fire protection and an identical basis
for calculation.