Escolar Documentos
Profissional Documentos
Cultura Documentos
Name of
Subject
MATERIAL
SCIENCE
Periods
L T P
3 1 0
Evaluation Scheme
CT TA TOTAL ESC
30 20
50
100
Subject
Total
150
Credit
4
INDEX
Unit
Page No.
3-27
II
28-62
III
63-95
IV
96-112
113-139
UNIT I
Introduction
Materials science, also commonly known as materials science and engineering, is an
interdisciplinary field which deals with the discovery and design of new materials. This
relatively new scientific field involves studying materials through the materials paradigm
(synthesis, structure, properties and performance). It incorporates elements of physics and
chemistry, and is at the forefront of nano science and nanotechnology research. In recent years,
materials science has become more widely known as a specific field of science and engineering.
Importance of Materials
A material is defined as a substance (most often a solid, but other condensed phases can be
included) that is intended to be used for certain applications. There are a myriad of materials
around usthey can be found in anything from buildings to spacecrafts. Materials can generally
be divided into two classes: crystalline and non-crystalline. The traditional examples of materials
are metals, ceramics and polymers. New and advanced materials that are being developed
include semiconductors, nanomaterials, biomaterials etc.
The material of choice of a given era is often a defining point. Phrases such as Stone Age,
Bronze Age, Iron Age, and Steel Age are great examples. Originally deriving from the
manufacture of ceramics and its putative derivative metallurgy, materials science is one of the
oldest forms of engineering and applied science. Modern materials science evolved directly from
metallurgy, which itself evolved from mining and (likely) ceramics and the use of fire. A major
breakthrough in the understanding of materials occurred in the late 19th century, when the
American scientist Josiah Willard Gibbs demonstrated that the thermodynamic properties related
to atomic structure in various phases are related to the physical properties of a material.
Important elements of modern materials science are a product of the space race: the
understanding and engineering of the metallic alloys, and silica and carbon materials, used in the
construction of space vehicles enabling the exploration of space. Materials science has driven,
and been driven by, the development of revolutionary technologies such as plastics,
semiconductors, and biomaterials.
Before the 1960s (and in some cases decades after), many materials science departments were
named metallurgy departments, reflecting the 19th and early 20th century emphasis on metals.
The field has since broadened to include every class of materials, including ceramics, polymers,
semiconductors, magnetic materials, medical implant materials, biological materials and
nanomaterials (materiomics).
Historical Perspective
Materials are so important in the development of civilization that we associate ages with them. In
the origin of human life on earth, the Stone Age, people used only natural materials like stone,
clay, skins, and wood. When people found copper and how to make it harder by alloying, the
Bronze Age started about 3000 BC. The use of iron and steel, stronger materials that gave
advantage in wars started at about 1200 BC. The next big step was the discovery of a cheap
process to make steel around 1850, which enabled the railroads and the building of the modern
infrastructure of the industrial world.
be able to select a material for a given use based on considerations of cost and performance.
To
understand the limits of materials and the change of their properties with use.
To
be able to create a new material that will have some desirable properties.
All engineering disciplines need to know about materials. Even the most immaterial like
software or system engineering depend on the development of new materials, which in turn alter
the economics, like software-hardware trade-offs. Increasing applications of system engineering
are in materials manufacturing (industrial engineering) and complex environmental systems.
Classification of Materials
Like many other things, materials are classified in groups, so that our brain can handle the
complexity. One could classify them according to structure, or properties, or use. The one that
we will use is according to the way the atoms are bound together:
Metals: The valence electrons are detached from atoms, and spread in an 'electron sea' that
"glues" the ions together. Metals are usually strong, conduct electricity and heat well and are
opaque to light (shiny if polished). Examples: aluminum, steel, brass, gold.
Semiconductors: The bonding is covalent (electrons are shared between atoms). Their electrical
properties depend extremely strongly on minute proportions of contaminants. They are opaque to
visible light but transparent to the infrared. Examples: Si, Ge, GaAs.
Ceramics: Atoms behave mostly like either positive or negative ions, and are bound by
Coulomb forces between them. They are usually combinations of metals or semiconductors with
oxygen, nitrogen or carbon (oxides, nitrides, and carbides).Examples: glass, porcelain, many
minerals.
Polymers: are bound by covalent forces and also by weak van der Waals forces, and usually
based on H, C and other non-metallic elements. They decompose at moderate temperatures (100
400 C), and are lightweight. Other properties vary greatly. Examples: plastics (nylon, teflon,
polyester) and rubber. Other categories are not based on bonding. A particular microstructure
identifies
Composites: Composites made of different materials in intimate contact (example: fiberglass,
concrete, wood) to achieve specific properties. Biomaterials can be any type of material that is
biocompatible and used, for instance, to replace human body parts.
Advanced Materials
Materials used in "High-Tec" applications, usually designed for maximum performance, and
normally expensive. Examples are titanium alloys for supersonic airplanes, magnetic alloys for
computer disks, special ceramics for the heat shield of the space shuttle, etc.
Modern Material's Needs
materials
Use of nuclear energy requires solving problem with residues, or advances in nuclear waste
processing.
Hypersonic flight
Optical
Civil
requires materials that are light, strong and resist high temperatures.
Structures:
materials that are strong like metals and resist corrosion like plastics.
Atomic models
Thomson atomic model
A schematic presentation of the plum pudding model of the atom; in Thomson's mathematical
model the "corpuscles" (or modern electrons) were arranged non-randomly, in rotating rings
The current model of the sub-atomic structure involves a dense nucleus surrounded by a
probabilistic "cloud" of electrons
The plum pudding model was a model of the atom that incorporated the recently discovered
electron, and was proposed by J. J. Thomson in 1904. Thomson had discovered the electron in
1897. The plum pudding model was abandoned after discovery of the atomic nucleus. The plum
pudding model of the atom is also known as the "Blueberry Muffin" model.
In this model, the atom is composed of electrons (which Thomson still called "corpuscles",
though G. J. Stoney had proposed that atoms of electricity be called electrons in 1894)
surrounded by a soup of positive charge to balance the electrons' negative charges, like
negatively charged "raisins" surrounded by positively charged "pudding". The electrons (as we
know them today) were thought to be positioned throughout the atom, but with many structures
possible for positioning multiple electrons, particularly rotating rings of electrons (see below).
Instead of a soup, the atom was also sometimes said to have had a "cloud" of positive charge.
With this model, Thomson abandoned his earlier "nebular atom" hypothesis in which the atom
was composed of immaterial vortices. Now, at least part of the atom was to be composed of
Thomson's particulate negative "corpuscles", although the rest of the positively charged part of
the atom remained somewhat nebulous and ill-defined.
The 1904 Thomson model was disproved by the 1909 gold foil experiment of Hans Geiger and
Ernest Marsden. This was interpreted by Ernest Rutherford in 1911 to imply a very small nucleus
of the atom containing a very high positive charge (in the case of gold, enough to balance about
100 electrons), thus leading to the Rutherford model of the atom. Although gold has an atomic
number of 79, immediately after Rutherford's paper appeared in 1911 Antonius Van den Broek
made the intuitive suggestion that atomic number is nuclear charge. The matter required
experiment to decide. Henry Moseley's work showed experimentally in 1913 (see Moseley's law)
that the effective nuclear charge was very close to the atomic number (Moseley found only one
unit difference), and Moseley referenced only the papers of Van den Broek and Rutherford. This
work culminated in the solar-system-like (but quantum-limited) Bohr model of the atom in the
same year, in which a nucleus containing an atomic number of positive charge is surrounded by
an equal number of electrons in orbital shells. Bohr had also inspired Moseley's work.
Thomson's model was compared (though not by Thomson) to a British dessert called plum
pudding, hence the name. Thomson's paper was published in the March 1904 edition of the
Philosophical Magazine, the leading British science journal of the day. In Thomson's view: the
atoms of the elements consist of a number of negatively electrified corpuscles enclosed in a
sphere of uniform positive electrification.
In this model, the electrons were free to rotate within the blob or cloud of positive substance.
These orbits were stabilized in the model by the fact that when an electron moved farther from
the center of the positive cloud, it felt a larger net positive inward force, because there was more
material of opposite charge, inside its orbit (see Gauss's law). In Thomson's model, electrons
were free to rotate in rings which were further stabilized by interactions between the electrons,
and spectra were to be accounted for by energy differences of different ring orbits. Thomson
attempted to make his model account for some of the major spectral lines known for some
elements, but was not notably successful at this. Still, Thomson's model (along with a similar
Saturnian ring model for atomic electrons, also put forward in 1904 by Nagaoka after James
Clerk Maxwell's model of Saturn's rings), were earlier harbingers of the later and more
successful solar-system-like Bohr model of the atom.
Rutherford model
Rutherford overturned Thomson's model in 1911 with his well-known gold foil experiment in
which he demonstrated that the atom has a tiny, heavy nucleus. Rutherford designed an
experiment to use the alpha particles emitted by a radioactive element as probes to the unseen
world of atomic structure.
Rutherford presented his own physical model for subatomic structure, as an interpretation for the
unexpected experimental results. In it, the atom is made up of a central charge (this is the modern
atomic nucleus, though Rutherford did not use the term "nucleus" in his paper) surrounded by a
cloud of (presumably) orbiting electrons. In this May 1911 paper, Rutherford only commits
himself to a small central region of very high positive or negative charge in the atom.
For concreteness, consider the passage of a high speed particle through an atom having a
positive central charge N e, and surrounded by a compensating charge of N electrons.
From purely energetic considerations of how far particles of known speed would be able to
penetrate toward a central charge of 100 e, Rutherford was able to calculate that the radius of his
gold central charge would need to be less (how much less could not be told) than 3.4 x 1014
metres. This was in a gold atom known to be 1010 meters or so in radiusa very surprising
finding, as it implied a strong central charge less than 1/3000th of the diameter of the atom.
The Rutherford model served to concentrate a great deal of the atom's charge and mass to a very
small core, but didn't attribute any structure to the remaining electrons and remaining atomic
mass. It did mention the atomic model of Hantaro Nagaoka, in which the electrons are arranged
in one or more rings, with the specific metaphorical structure of the stable rings of Saturn. The
plum pudding model of J.J. Thomson also had rings of orbiting electrons. Jean Baptiste Perrin
claimed in his Nobel Lecture that he was the first one to suggest the model in his paper dated
1901.
The Rutherford paper suggested that the central charge of an atom might be "proportional" to its
atomic mass in hydrogen mass units u (roughly 1/2 of it, in Rutherford's model). For gold, this
mass number is 197 (not then known to great accuracy) and was therefore modeled by
Rutherford to be possibly 196 u. However, Rutherford did not attempt to make the direct
connection of central charge to atomic number, since gold's "atomic number" (at that time
merely its place number in the periodic table) was 79, and Rutherford had modeled the charge to
be about + 100 units (he had actually suggested 98 units of positive charge, to make half of 196).
Thus, Rutherford did not formally suggest the two numbers (periodic table place, 79, and nuclear
charge, 98 or 100) might be exactly the same.
10
Bohr model
In the early 20th century, experiments by Ernest Rutherford established that atoms consisted of a
diffuse cloud of negatively charged electrons surrounding a small, dense, positively charged
nucleus. Given this experimental data, Rutherford naturally considered a planetary-model atom,
the Rutherford model of 1911 electrons orbiting a solar nucleus however, said planetarymodel atom has a technical difficulty. The laws of classical mechanics (i.e. the Larmor formula),
predict that the electron will release electromagnetic radiation while orbiting a nucleus. Because
the electron would lose energy, it would rapidly spiral inwards, collapsing into the nucleus on a
timescale of around 16 picoseconds. This atom model is disastrous, because it predicts that all
atoms are unstable.
Also, as the electron spirals inward, the emission would rapidly increase in frequency as the orbit
got smaller and faster. This would produce a continuous smear, in frequency, of electromagnetic
radiation. However, late 19th century experiments with electric discharges have shown that
atoms will only emit light (that is, electromagnetic radiation) at certain discrete frequencies.
To overcome this difficulty, Niels Bohr proposed, in 1913, what is now called the Bohr model of
the atom. He suggested that electrons could only have certain classical motions:
1.
2.
The electrons can only orbit stably, without radiating, in certain orbits (called by Bohr the
"stationary orbits") at a certain discrete set of distances from the nucleus. These orbits are
associated with definite energies and are also called energy shells or energy levels. In these
orbits, the electron's acceleration does not result in radiation and energy loss as required by
classical electromagnetics.
3.
Electrons can only gain and lose energy by jumping from one allowed orbit to another,
absorbing or emitting electromagnetic radiation with a frequency determined by the
energy difference of the levels according to the Planck relation:
where h is Planck's constant. The frequency of the radiation emitted at an orbit of period T is as
it would be in classical mechanics; it is the reciprocal of the classical orbit period:
The significance of the Bohr model is that the laws of classical mechanics apply to the motion of
the electron about the nucleus only when restricted by a quantum rule. Although rule 3 is not
11
completely well defined for small orbits, because the emission process involves two orbits with
two different periods, Bohr could determine the energy spacing between levels using rule 3 and
come to an exactly correct quantum rule: the angular momentum L is restricted to be an integer
multiple of a fixed unit:
where n = 1, 2, 3, ... is called the principal quantum number, and = h/2. The lowest value of n
is 1; this gives a smallest possible orbital radius of 0.0529 nm known as the Bohr radius. Once an
electron is in this lowest orbit, it can get no closer to the proton. Starting from the angular
momentum quantum rule, Bohr was able to calculate the energies of the allowed orbits of the
hydrogen atom and other hydrogen-like atoms and ions. Other points are:
1. Like Einstein's theory of the Photoelectric effect, Bohr's formula assumes that during a
quantum jump a discrete amount of energy is radiated. However, unlike Einstein, Bohr stuck
to the classical Maxwell theory of the electromagnetic field. Quantization of the
electromagnetic field was explained by the discreteness of the atomic energy levels; Bohr did
not believe in the existence of photons.
2. According to the Maxwell theory the frequency of classical radiation is equal to the rotation
frequency rot of the electron in its orbit, with harmonics at integer multiples of this
frequency. This result is obtained from the Bohr model for jumps between energy levels En
and Enk when k is much smaller than n. These jumps reproduce the frequency of the k-th
harmonic of orbit n. For sufficiently large values of n (so-called Rydberg states), the two
orbits involved in the emission process have nearly the same rotation frequency, so that the
classical orbital frequency is not ambiguous. But for small n (or large k), the radiation
frequency has no unambiguous classical interpretation. This marks the birth of the
correspondence principle, requiring quantum theory to agree with the classical theory only in
the limit of large quantum numbers.
3. The Bohr-Kramers-Slater theory (BKS theory) is a failed attempt to extend the Bohr model
which violates the conservation of energy and momentum in quantum jumps, with the
conservation laws only holding on average. Bohr's condition, that the angular momentum is
12
Substituting de Broglie's wavelength of h/p reproduces Bohr's rule. In 1913, however, Bohr
justified his rule by appealing to the correspondence principle, without providing any sort of
wave interpretation. In 1913, the wave behavior of matter particles such as the electron (i.e.,
matter waves) was not suspected.
the electron's average momentum at that point, since high electron momentum at a given position
tends to "localize" the electron in that position, via the properties of electron wave-packets (see
the Heisenberg uncertainty principle for details of the mechanism).
This relationship means that certain key features can be observed in both drum membrane modes
and atomic orbitals. For example, in all of the modes analogous to s orbitals (the top row in the
animated illustration below), it can be seen that the very center of the drum membrane vibrates
most strongly, corresponding to the antinode in all s orbitals in an atom. This antinode means the
electron is most likely to be at the physical position of the nucleus (which it passes straight
through without scattering or striking it), since it is moving (on average) most rapidly at that
point, giving it maximal momentum.
A mental "planetary orbit" picture closest to the behavior of electrons in s orbitals, all of which
have no angular momentum, might perhaps be that of a Keplerian orbit with the orbital
eccentricity of 1 but a finite major axis, not physically possible (because particles were to
collide), but can be imagined as a limit of orbits with equal major axes but increasing
eccentricity.
Below, a number of drum membrane vibration modes are shown. The analogous wave functions
of the hydrogen atom are indicated. A correspondence can be considered where the wave
functions of a vibrating drum head are for a two-coordinate system (r,) and the wave
functions for a vibrating sphere are three-coordinate (r,,).
Atomic bonding in solids
Primary Inter-atomic Bonds
Ionic Bonding
This is the bond when one of the atoms is negative (has an extra electron) and another is positive
(has lost an electron). Then there is a strong, direct Coulomb attraction. An example is NaCl. In
the molecule, there are more electrons around Cl, forming Cl- and less around Na, forming Na+.
Ionic bonds are the strongest bonds. In real solids, ionic bonding is usually combined with
covalent bonding.
Covalent Bonding
14
In covalent bonding, electrons are shared between the molecules, to saturate the valency. The
simplest example is the H2 molecule, where the electrons spend more time in between the nuclei
than outside, thus producing bonding.
Metallic Bonding
In metals, the atoms are ionized, loosing some electrons from the valence band. Those electrons
form an electron sea, which binds the charged nuclei in place, in a similar way that the electrons
in between the H atoms in the H2 molecule bind the protons.
Secondary Bonding (Van der Waals)
Fluctuating Induced Dipole Bonds
Since the electrons may be on one side of the atom or the other, a dipole is formed: the + nucleus
at the center, and the electron outside. Since the electron moves, the dipole fluctuates. This
fluctuation in atom A produces a fluctuating electric field that is felt by the electrons of an
adjacent atom, B. Atom B then polarizes so that its outer electrons are on the side of the atom
closest to the + side (or opposite to the side) of the dipole in A. This bond is called van der
Waals bonding.
Polar Molecule-Induced Dipole Bonds
A polar molecule like H2O (Hs are partially +, O is partially), will induce a dipole in a nearby
atom, leading to bonding.
Permanent Dipole Bonds
This is the case of the hydrogen bond in ice. The H end of the molecule is positively charged and
can bond to the negative side of another dipolar molecule, like the O side of the H2O dipole
Crystallography
Crystal Structures:
Atoms self-organize in crystals, most of the time. The crystalline lattice is a periodic array of the
atoms. When the solid is not crystalline, it is called amorphous. Examples of crystalline solids
15
are metals, diamond and other precious stones, ice, graphite. Examples of amorphous solids are
glass, amorphous carbon (a-C), amorphous Si, most plastics To discuss crystalline structures it is
useful to consider atoms as being hard spheres, with well-defined radii. In this scheme, the
shortest distance between two like atoms is one diameter.
Crystal Lattice is used to represent a three-dimensional periodic array of points coinciding with
atom positions.
Unit cell is smallest repeatable entity that can be used to completely represent a crystal structure.
It is the building block of crystal structure.
Bravais lattices
When the crystal systems are combined with the various possible lattice centerings, we arrive at
the Bravais lattices. They describe the geometric arrangement of the lattice points, and thereby
the translational symmetry of the crystal. In three dimensions, there are 14 unique Bravais
lattices that are distinct from one another in the translational symmetry they contain. All
crystalline materials recognized until now (not including quasicrystals) fit in one of these
arrangements. The fourteen three-dimensional lattices, classified by crystal system, are shown
above. The Bravais lattices are sometimes referred to as space lattices.
The crystal structure consists of the same group of atoms, the basis, positioned around each and
every lattice point. This group of atoms therefore repeats indefinitely in three dimensions
according to the arrangement of one of the 14 Bravais lattices. The characteristic rotation and
mirror symmetries of the group of atoms, or unit cell, is described by its crystallographic point
group.
Metallic Crystal Structures
Important properties of the unit cells are
The type of atoms and their radii R.
Cell dimensions (side a in cubic cells, side of base a and height c in HCP) in terms of R.
n, number of atoms per unit cell. For an atom that is shared with m adjacent unit cells, we
only count a fraction of the atom, 1/m.
16
CN, the coordination number, which is the number of closest neighbors to which an atom is
bonded.
APF, the atomic packing factor, which is the fraction of the volume of the cell actually
occupied by the hard spheres. APF = Sum of atomic volumes/Volume of cell.
Crystalline and Non-crystalline materials:
Single Crystals
Crystals can be single crystals where the whole solid is one crystal. Then it has a regular
geometric structure with flat faces.
Polycrystalline Materials
A solid can be composed of many crystalline grains, not aligned with each other. It is called
polycrystalline. The grains can be more or less aligned with respect to each other. Where they
meet is called a grain boundary.
Non-Crystalline Solids
In amorphous solids, there is no long-range order. But amorphous does not mean random, since
the distance between atoms cannot be smaller than the size of the hard spheres. Also, in many
cases there is some form of short-range order. For instance, the tetragonal order of crystalline
SiO2 (quartz) is still apparent in amorphous SiO2 (silica glass.)
17
The length of the vector projection on each of three axes aremeasured in terms of unit cell
dimensions
These three numbers are made to smallest integer values, known as indices, by
multiplying or dividing by a commonfactor
18
The smaller a Miller index, the more nearly parallel the plane is to the axis.
The larger a Miller index, the more nearly perpendicular a plane is to that axis.
Multiplying or dividing a Miller index by a constant has no effect on the orientation of the
plane
Specifying dimensions in unit cell terms means that the same label can be applied to any face
with a similar stacking pattern, regardless of the crystal class of the crystal. Face 111 always
steps the same way regardless of crystal system.
19
Imperfections in Solids
Point Defects
Vacancies and Self-Interstitials
A vacancy is a lattice position that is vacant because the atom is missing. It is createdwhen the
solid is formed. There are other ways of making a vacancy, but they also occur naturally as a
result of thermal vibrations.
An interstitial is an atom that occupies a place outside the normal lattice position. It maybe the
same type of atom as the others (self interstitial) or an impurity atom. In the case of vacancies
and interstitials, there is a change in the coordination of atoms around the defect. This means that
the forces are not balanced in the same way as for other atoms in the solid, which results in
lattice distortion around the defect A hightemperature is needed to have a high thermal
concentration of vacancies.
Frenkel-defect is a vacancy-interstitial pair of cations
Schottky-defect is a pair of nearby cation and anion vacancies
20
DislocationsLinear Defects
Dislocations are abrupt changes in the regular ordering of atoms, along a line (dislocation line) in
the solid. They occur in high density and are very important in mechanical properties of material.
They are characterized by the Burgers vector, found by doing a loop around the dislocation line
and noticing the extra inter atomic spacing needed to close the loop. The Burgers vector in
metals points in a close packed direction.
Line Defects
Line defects or Dislocations are abrupt change in atomic order along a line.
They occur if an incomplete plane inserted between perfect planes of atoms or when
vacancies are aligned in a line.
A dislocation is the defect responsible for the phenomenon of slip, by which most metals
deform plastically.
Dislocations occur in high densities (108-1010 m-2 ), and are intimately connected to
almost all mechanical properties which are in fact structure-sensitive.
21
It is unique to a dislocation, and usually has the direction of close packed lattice
direction. It is also the slip direction of a dislocation.
It represents the magnitude and direction of distortion associated with that particular
dislocation.
Two limiting cases of dislocations, edge and screw, are characterized by Burgers vector
perpendicular to the dislocation line (t) and Burgers vector parallel to the dislocation line
respectively. Ordinary dislocation is of mixed character of edge and screw type.
Edge dislocations occur when an extra plane is inserted. The dislocation line is at the end of the
plane. In an edge dislocation, the Burgers vector is perpendicular to the dislocation line.
Line Defects Edge Dislocation
It will have regions of compressive and tensile stresses on either side of the plane
containing dislocation.
Screw dislocations result when displacing planes relative to each other through shear. In this
case, the Burgers vector is parallel to the dislocation line.
Line Defects Screw Dislocation
For positive screw dislocation, dislocation line direction is parallel to Burgers vector,
and vice versa.
22
Interfacial Defects:
The environment of an atom at a surface differs from that of an atom in the bulk, in that the
number of neighbors (coordination) decreases. This introduces unbalanced forces which result in
relaxation (the lattice spacing is decreased) or reconstruction (the crystal structure changes). The
density of atoms in the region including the grain boundary is smaller than the bulk value, since
void space occurs in the interface. Surfaces and interfaces are very reactive and it is usual that
impurities segregate there. Since energy is required to form a surface, grains tend to grow in size
at the expense of smaller grains to minimize energy. This occurs by diffusion, which is
accelerated at high temperatures.
23
Interfacial Defects
E.g.: External surface, Grain boundaries, Stacking faults, Twin boundaries, Phase
boundaries.
Volume defects are three-dimensional in nature.These defects are introduced, usually, during
processing and fabrication operations like casting, forming etc.E.g.: Pores, Cracks, Foreign
particles These defects act like stress raisers, thus deleterious to mechanical properties of parent
solids. In some instances, foreign particles are added to strengthen the solid dispersion
hardening. Particles added are hindrances to movement of dislocations which have to cut through
or bypass the particles thus increasing the strength.
25
The magnitude of the distance between two adjacent and parallel planes of atoms (i.e., the
interplanar spacing ) is a function of the Miller indices (h, k, and l) as well as the lattice
parameter(s). For example, for crystal structures that have cubic symmetry
26
27
UNIT II
28
Elastic deformation:
When the stress is removed, the material returns to the dimension it had before the loadwas
applied. Valid for small strains (except the case of rubbers).Deformation is reversible, non
permanent
29
Plastic deformation:
When the stress is removed, the material does not return to its previous dimension but there is a
permanent, irreversible deformation. In tensile tests, if the deformation is elastic, the stress-strain
relationship is called Hooke's law:
=E
That is, E is the slope of the stress-strain curve. E is Young's modulus or modulus of elasticity. In
some cases, the relationship is not linear so that E can be defined alternatively as the local slope:
E = d/d
Shear stresses produce strains according to:
=G
where G is the shear modulus. Elastic moduli measure the stiffness of the material. They are
related to the second derivative of the interatomic potential, or the first derivative of the force vs.
inter nuclear distance. By examining these curves we can tell which material has a higher
modulus. Due to thermal vibrations the elastic modulus decreases with temperature. E is large for
ceramics (stronger ionic bond) and small for polymers (weak covalent bond). Since the
interatomic distances depend on direction in the crystal, E depends on direction (i.e., it is
anisotropic) for single crystals. For randomly oriented policrystals, E is isotropic.
30
Tensile Properties
Yield point. If the stress is too large, the strain deviates from being proportional to the stress.
The point at which this happens is the yield point because there the material yields, deforming
permanently (plastically).
Yield stress. Hooke's law is not valid beyond the yield point. The stress at the yield point is
called yield stress, and is an important measure of the mechanical properties of materials. In
practice, the yield stress is chosen as that causing a permanent strain of 0.002 The yield stress
measures the resistance to plastic deformation. The reason for plastic deformation, in normal
materials, is not that the atomic bond is stretched beyond repair, but the motion of dislocations,
which involves breaking and reforming bonds. Plastic deformation is caused by the motion of
dislocations.
Tensile strength: When stress continues in the plastic regime, the stress-strain passes through a
maximum, called the tensile strength, and then falls as the material starts to develop a neck and it
finally breaks at the fracture point.
For structural applications, the yield stress is usually a more important property than the tensile
strength, since once it is passed, the structure has deformed beyond acceptable limits.
Ductility: The ability to deform before braking. It is the opposite of brittleness. Ductility can be
given either as percent maximum elongation max or maximum area reduction.
%EL = max x 100 %
%AR = (A0 - Af)/A0
These are measured after fracture (repositioning the two pieces back together).
Resilience: Capacity to absorb energy elastically. The energy per unit volume is the area under
the strain-stress curve in the elastic region.
Toughness: Ability to absorb energy up to fracture. The energy per unit volume is the total area
under the strain-stress curve. It is measured by an impact test .
31
10
Corundum
Topaz
Quartz
Orthoclase (Feldspar) 6
32
Apatite
Fluorite
Calcite
Gypsum
Talc
reducing the depth of penetration. The permanent increase in depth of penetration, resulting from
the application and removal of the additional major load is used to calculate the Rockwell
hardness number. Advantages of the Rockwell hardness method include the direct Rockwell
hardness number readout and rapid testing time.
softest and hardest of materials, under varying loads, the Vickers machine is a floor standing unit
that is more expensive than the Brinell or Rockwell machines.
F = Load in kgf
D =Arithmetic mean of the two diagonals, d1 and d2 in mm
HV = Vickers hardness
35
Micro-hardness Test
Knoop Hardness Test
The term microhardness test usually refers to static indentations made with loads not exceeding 1
kgf. The indenter is either the Vickers diamond pyramid or the Knoop elongated diamond
pyramid. The procedure for testing is very similar to that of the standard Vickers hardness test,
except that it is done on a microscopic scale with higher precision instruments. The surface being
tested generally requires a metallographic finish; the smaller the load used, the higher the surface
finish required. Precision microscopes are used to measure the indentations; these usually have a
magnification of around X500 and measure to an accuracy of +0.5 micrometres. Also with the
same observer differences of +0.2 micrometres can usually be resolved. It should, however, be
added that considerable care and experience are necessary to obtain this accuracy.
The Knoop hardness number KHN is the ratio of the load applied to the indenter, P (kgf) to the
unrecovered projected area A (mm2)
Failure
Fundamentals of Fracture
Fracture is a form of failure where the material separates in pieces due to stress, at temperatures
below the melting point. The fracture is termed ductile or brittle depending on whether the
elongation is large or small. Steps in fracture (response to stress):
Crack
formation
Crack
propagation
37
Ductile Fracture
Stages of ductile fracture
Initial necking
Small cavity formation (micro voids)
Void growth (ellipsoid) by coalescence into a crack
38
Impact Fracture:
Impact fractures can best be described as a flute or strip of material that was cleanly sheared
from a projectile point. The most common type of impact fracture starts at the tip of a point and
runs down one blade edge possibly reaching the shoulder of a point. Some points were reworked
into a useable point after having been damaged by an impact fracture. Normalized tests, like the
Charpoy and Izod tests measure the impact energy required to fracture a notched specimen with
a hammer mounted on a pendulum. The energy is measured by the change in potential energy
(height) of the pendulum. This energy is called notch toughness.
Ductile brittle transition
Ductile to brittle transition occurs in materials when the temperature is dropped below a
transition temperature. Alloying usually increases the ductile-brittle transition temperature, for
ceramics, this type of transition occurs at much higher temperatures than for metals.
The notched-bar impact test can be used to determine whether or not a material experiences a
ductile-to-brittle transition as the temperature is decreased. In such a transition, at higher
temperatures the impact energy is relatively large since the fracture is ductile. As the temperature
39
is lowered, the impact energy drops over a narrow temperature range as the fracture becomes
more brittle.
The transition can also be observed from the fracture surfaces, which appear fibrous or dull for
totally ductile fracture, and granular and shiny for totally brittle fracture. Over the ductile-tobrittle transition features of both types will exist.
While for pure materials the transition may occur very suddenly at a particular temperature, for
many materials the transition occurs over a range of temperatures. This causes difficulties when
trying to define a single transition temperature and no specific criterion has been established.
The ductile-brittle transition is exhibited in bcc metals, such as low carbon steel, which become
brittle at low temperature or at very high strain rates. Fcc metals, however, generally remain
ductile at low temperatures.
Fatigue:
Fatigue is the catastrophic failure due to dynamic (fluctuating) stresses. It can happen in bridges,
airplanes, machine components, etc. The characteristics are: long period of cyclic strain
the most usual (90%) of metallic failures (happens also in ceramics and polymers)
Cyclic Stresses
These are characterized by maximum, minimum and mean stress, the stress amplitude, and the
stress ratio.
Crack Initiation and Propagation
Stages is fatigue failure:
I. crack initiation at high stress points (stress raisers)
II. propagation (incremental in each cycle)
III. final failure by fracture
Stage I - propagation
slow
Stage II - propagation
Crack propagates by repetitive plastic blunting and sharpening of the crack tip.
Creep
Creep is the time-varying plastic deformation of a material stressed at high temperatures.
Examples: turbine blades, steam generators. Keys are the time dependence of the strain and the
high temperature.
41
42
43
44
NDT are: magnetic dust method, penetrating liquid method, ultrasonic test and
radiography. All NDTs are used to detect various types of flaws on the surface of material or
internal inclusions of impurities and these techniques are also very useful during preventive
maintenance and repair. There are few techniques which do not require any special apparatus and
are quite simple to handle and only a moderate skill being required. Some of the applications of
NDTs are detecting: (i) surface cracks (ii) material composition (iii) internal inclusions (iv)
internal voids and discontinuities and (v) condition of internal stresses.
Ultrasonic Test
High frequency ultrasonic (sound) waves are applied to the test piece by a Piezoelectric crystal.
If the test piece is free from cracks, or flawless, then it reflects ultrasonic waves without
distortion. If there are any flaws in the specimen, the time taken by the ultrasonic waves will be
less as the reflection of these waves will be from flaw points and not from the bottom of the
specimen. Cathode ray oscilloscope (CRO) is used to receive the sound signals, whose time base
circuit is connected to it. Knowing the time interval between the transmission of the sound pulse
and the reception of the echo signal, we can calculate the depth of the crack. This test is a very
fast method of inspection and often used to test aerospace components and automobiles. This test
is generally used to detect internal cracks like shrinkage cavities, hot tears, zones of corrosion
and non-metallic inclusions.
Liquid-Penetration test
This test is employed for detection of small defects which are very small to detect with the naked
eye. This test is used to detect surface cracks or flaws in non-ferrous metals. This test employs a
visible colour contrast dye penetrant technique for the detection of open surface flaws in metallic
and non-metallic objects. The penetrants are applied by spraying over the surface of material to
be inspected. The excess penetrant is then washed or cleaned. Absorbent powder is then applied
to absorb the penetrants in the cracks, voids which reveals the flaws. This test reveals flaws such
as shrinkage cracks, porosity, fatigue cracks, grinding cracks, forging cracks, seams, heat
treatment cracks and leaks etc., on castings, weldings, machined parts, cutting tools, pipes and
tubes. If the fluorescent penetrant is used, the developed surface must be examined under ultra
violet light to see the presence of defects. This technique is used for non-porous and nonabsorbent materials. Care may be taken to clean the surface so that it is free from dust, scale, etc.
46
to have better results. Penetrants are highly toxic and flammable and hence proper precautions
should be taken both during use and of storage of penetrants.
Microstructural Exam
Microstructure is defined as the structure of a prepared surface or thin foil of material as
revealed by a microscope above 25 magnification. The microstructure of a material can
strongly influence physical properties such as strength, toughness, ductility, hardness, corrosion
resistance, high/low temperature behavior, wear resistance, and so on, which in turn govern the
application of these materials in industrial practice.
a) Sectioning and cutting
The areas of interest forming the metallography specimens need to be sectioned for ease of
handling. Depending on the type of material, the sectioning operation can be done by using
abrasive cutter (for metal and metallic composite), diamond wafer cutter (ceramics, electronics
and minerals) or thin sectioning with a microtome (plastics). In order not to damage the
specimen, proper cutting requires the correct selection of abrasive cutting wheel, proper cutting
speed & cutting load and the use of coolant.
b) Mounting
The mounting operation accomplishes three important functions:
1. To protects the specimen edge and maintain the integrity of materials surface features.
2. Fill voids in porous materials.
3. Improves handling of irregular shaped samples.
Samples for microstructure evaluation are typically encapsulated in a plastic mount for handling
during sample preparation. Large sample or samples for macrostructure evaluation can be
prepared without mounting.
The metallography specimen mounting is done by encapsulating the specimen into:
1. A compression/hot mounting compound (thermosets e.g. phenolics, epoxies or
thermoplastics e.g. acrylics)
47
2. A castable resin/cold mounting (e.g. acrylics resins, epoxy resins and polyester resins)
c) Grinding
Grinding is required to ensure the surface is flat & parallel and to reduce the damage created
during sectioning. Grinding is accomplished by decreasing the abrasive grit size sequentially to
obtain the required fine surface finish prior to polishing. It is important to note that the final
appearance of the prepared surface is dependent on the machine parameters such as
grinding/polishing pressure, relative velocity distribution and the direction of grinding/polishing.
d) Polishing
For microstructure examination a mirror/reflective finish is needed whereas a finely ground
finish is adequate for macrostructure evaluation. Polishing can be divided into two main steps:
1. Rough polishing
The purpose is to remove the damage produced during grinding. Proper polishing will maintain
the specimen flatness and retain all inclusions or secondary phases by eliminating the previous
damage and maintaining the specimen integrity.
2. Fine polishing
The purpose is to remove only surface damage.
e) Etching
Etchans are specially formulated for the specific material and evaluation objectives. Etching
alters the microstructural features based on composition; stress or crystal structure and it will
develop the surface topology, which can be visible in the microscope. Typically, chemical
etching involve immersing the polished surface in the prepared chemical solution for a specified
time (usually seconds) followed by rinsing the etched specimen under running tap water and
drying.
48
f) Microscopic Analysis
For microscopic analysis, a reflective surface is required. The analysis can be done by using a
metallurgy microscope.
where L is the length of the line and N is the number of intercepts which the grain boundary
makes with the line. This can be related to the ratio of the grain-boundary surface area S to the
volume of the grains, V, by the equation
where 1 is the total length of grain boundary n a random plane of polish and A is the total area
of the grains on a random plane of polish. A very common method of measuring grain size in the
United States is to compare the grains at a fixed magnification with the American Society for
Testing and Materials (ASTM) grain-size charts. The ASTM grain-size number n is related to N ,
49
the number of grains per square inch at a magnification of 100X by the relationship
Table shown compares the ASTM grain-size numbers with several other useful measures of
grain size.
Phase Diagrams
Equilibrium Phase Diagrams
Give the relationship of composition of a solution as a function of temperatures and the
quantities of phases in equilibrium. These diagrams do not indicate the dynamics when one
phase transforms into another. Sometimes diagrams are given with pressure as one of the
variables. In the phase diagrams we will discuss, pressure is assumed to be constant at one
atmosphere.
Binary Isomorphous Systems
This very simple case is one complete liquid and solid solubility, an isomorphous system. The
example is the Cu-Ni alloy of Fig. 9.2a. The complete solubility occurs because both Cu and Ni
have the same crystal structure (FCC), near the same radii, electronegativity and valence. The
liquidus line separates the liquid phase from solid or solid + liquid phases. That is, the solution is
50
liquid above the liquidus line. The solidus line is that below which the solution is completely
solid (does not contain a liquid phase.)
lower than that of the components (eutectic = easy to melt in Greek). At most two phases can be
in equilibrium within a phase field. Single-phase regions are separated by 2-phase regions.
52
53
54
treatments. The process is called precipitation hardening because the small particles of the new
phase are termed precipitates. Precipitation hardening and the treating of steel to form
tempered matrensite are totally different phenomena, even though the heat treatment procedures
are similar.
Precipitation reactions
A precipitation reaction is a reaction in which soluble ions in separate solutions are mixed
together to form an insoluble compound that settles out of solution as a solid. That insoluble
compound is called a precipitate
Kinetics of nucleation and growth
From a micro structural standpoint, the first process to accompany a phase transformation is
nucleation- the formation of very small particles or nuclei, of the new phase which are capable
of growing. The second stage is growth, in which the nuclei increase in size; during this process,
some volume of the parent phase disappears. The transformation reaches completion if growth of
these new phase particles is allowed to proceed until the equilibrium fraction is attained.
As would be expected, the time dependence of the transformations rate (which is often termed
the kinetics of a transformation) is an important consideration in the heat treatment of materials.
With many investigations, the fraction of reaction that has occurred is measured as a function of
time, while the temperature is maintained constant. Transformation progress is usually
ascertained by either microscopic examination or measurement of some physical property. Data
are plotted as the fraction of transformed material versus the logarithm of time; an S-shaped
curve, represents the typical kinetic behavior for most solid state reactions.
Solid Solutions
A solid solution may be formed when impurity atoms are added to a solid, in which case the
original crystal structure is retained and no new phases are formed.
Substitutional solid solutions: impurity atoms substitute for host atoms, and appreciable
solubility is possible only when atomic diameters and electronegativities for both atom types
are similar, when both elements have the same crystal structure, and when the impurity atoms
have a valence that is the same as or less than the host material.
56
Interstitial solid solutions: These form for relatively small impurity atoms that occupy
interstitial sites among the host atoms
57
The maximum solubility of C in - ferrite is 0.022 wt%. ferrite is only stable at high
temperatures. It is not important in practice. Austenite has a maximum C concentration of 2.14
wt %. It is not stable below the eutectic temperature (727 C) unless cooled rapidly (Chapter 10).
Cementite is in reality metastable, decomposing into -Fe and C when heated for several years
between 650 and 770 C.
-ferrite: It is solid solution of carbon in -iron. Maximum concentration of carbon in ferrite is 0.09% at 2719 F (1493C) which is the temperature of the peritectic transformation.
The crystal structure of -ferrite is BCC (cubic body centered).
Austenite: Austenite
is
interstitial
solid
solution of carbon in
-iron.
Austenite
has FCC (cubic face centered) crystal structure, permitting high solubility of carbon i.e. up to
2.06% at 2097 F (1147 C). Austenite does not exist below 1333 F (723C) and
maximum carbon concentration at this temperature is 0.83%.
-ferrite: It is solid solution of carbon in -iron. -ferrite has BCC crystal structure and
low solubility of carbon up to 0.025% at 1333 F (723C). -ferrite exists at room
temperature.
Critical temperatures
Upper critical temperature (point) A3 is the temperature, below which ferrite starts to form
as a result of ejection from austenite in the hypo-eutectoid alloys.
Upper critical temperature (point) ACM is the temperature, below which cementite starts to
form as a result of ejection from austenite in the hyper-eutectoid alloys.
58
Hypereutectoid steels (carbon content from 0.83 to 2.06%) consist of primary (proeutectoid)
cementite (according to the curve ACM) and Pearlite.
Cast irons (carbon content from 2.06% to 4.3%) consist of cementite ejected from austenite
according to the curve ACM , Pearlite and transformed ledeburite (ledeburite in which
austenite transformed to pearlite).
When the liquid of eutectic composition is cooled, at or below eutectic temperature this liquid
transforms simultaneously into two solid phases (two terminal solid solutions, represented by
and ). This transformation is known as eutectic reactionand is written symbolically as:
Liquid (L) solid solution-1 () + solid solution-2 ()
In the solid state analog of a eutectic reaction, called a eutectoid reaction, one solid phase having
eutectoid composition transforms into two different solid phases. Another set of invariant
reactions that occur often in binary systems are - peritectic reaction where a solid phase reacts
with a liquid phase to produce a new solid phase.
For their role in mechanical properties of the alloy, it is important to note that: Ferrite is soft and
ductile Cementite is hard and brittle. Thus, combining these two phases in solution an alloy can
be obtained with intermediate properties. (Mechanical properties also depend on the
microstructure, that is, how ferrite and cementite are mixed.)
Development of Microstructures in IronCarbon Alloys
The eutectoid composition of austenite is 0.8 wt %. When it cools slowly it forms perlite, a
lamellar or layered structure of two phases: -ferrite and cementite (Fe3C). Hypoeutectoid alloys
contain proeutectoid ferrite plus the eutectoid pearlite. Hypereutectoid alloys contain
proeutectoid cementite plus pearlite. Since reactions below the eutectoid temperature are in the
solid phase, the equilibrium is not achieved by usual cooling from austenite.
59
60
temperatures). This reduced grain growth leads to fine-grained microstructure (fine pearlite). At
higher temperatures, diffusion allows for larger grain growth, thus leading to coarse pearlite.
At lower temperatures nucleation starts to become slower, and a new phase is formed, bainite.
Since diffusion is low at low temperatures, this phase has a very fine (microscopic)
microstructure.
Spheroidite is a coarse phase that forms at temperatures close to the eutectoid temperature. The
relatively high temperatures caused a slow nucleation but enhances the growth of the nuclei
leading to large grains.
A very important structure is martensite, which forms when cooling austenite very fast
(quenching) to below a maximum temperature that is required for the transformation. It forms
nearly instantaneously when the required low temperature is reached; since no thermal activation
is needed, this is called an athermal transformation. Martensite is a different phase, a bodycentered tetragonal (BCT) structure with interstitial C atoms. Martensite is metastable and
decomposes into ferrite and pearlite but this is extremely slow (and not noticeable) at room
temperature.
In the examples, we used an eutectoid composition. For hypo- and hypereutectoid alloys, the
analysis is the same, but the proeutectoid phase that forms before cooling through the eutectoid
temperature is also part of the final microstructure.
62
UNIT III
63
64
65
arbitrary: Smith and Has hemi define the difference at 4.0%, while Degarmo, et al., define it at
8.0%. Most commonly, the phrase "alloy steel" refers to low-alloy steels.
Types:
According to the World Steel Association, there are over 3,500 different grades of steel,
encompassing unique physical, chemical and environmental properties.
In essence, steel is composed of iron and carbon, although it is the amount of carbon, as well as
the level of impurities and additional alloying elements that determines the properties of each
steel grade.
The carbon content in steel can range from 0.1-1.5%, but the most widely used grades of steel
contain only 0.1-0.25% carbon. Elements such as manganese, phosphorus and sulphur are found
in all grades of steel, but, whereas manganese provides beneficial effects, phosphorus and
sulphur are deleterious to steel's strength and durability.
Different types of steel are produced according to the properties required for their application,
and various grading systems are used to distinguish steels based on these properties. According
to the American Iron and Steel Institute (AISI), steels can be broadly categorized into four
groups based on their chemical compositions:
1.
Carbon Steels
2.
Alloy Steels
3.
Stainless Steels
4.
Tool Steels
1) Carbon Steels:
Carbon steels contain trace amounts of alloying elements and account for 90% of total steel
production. Carbon steels can be further categorized into three groups depending on their carbon
content:
2) Alloy Steels:
Alloy steels contain alloying elements (e.g. manganese, silicon, nickel, titanium, copper,
chromium and aluminum) in varying proportions in order to manipulate the steel's properties,
such as its hardenability, corrosion resistance, strength, formability, weldability or ductility.
Applications for alloys steel include pipelines, auto parts, transformers, power generators and
electric motors.
3) Stainless Steels:
Stainless steels generally contain between 10-20% chromium as the main alloying element and
are valued for high corrosion resistance. With over 11% chromium, steel is about 200 times more
resistant to corrosion than mild steel. These steels can be divided into three groups based on their
crystalline structure:
Austenitic: Austenitic steels are non-magnetic and non heat-treatable, and generally contain
18% chromium, 8% nickel and less than 0.8% carbon. Austenitic steels form the largest
portion of the global stainless steel market and are often used in food processing equipment,
kitchen utensils and piping.
Ferritic: Ferritic steels contain trace amounts of nickel, 12-17% chromium, less than 0.1%
carbon, along with other alloying elements, such as molybdenum, aluminum or titanium.
These magnetic steels cannot be hardened with heat treatment, but can be strengthened by
cold works.
Martensitic: Martensitic steels contain 11-17% chromium, less than 0.4% nickel and up to
1.2% carbon. These magnetic and heat-treatable steels are used in knives, cutting tools, as
well as dental and surgical equipment.
4) Tool Steels:
Tool steels contain tungsten, molybdenum, cobalt and vanadium in varying quantities to increase
heat resistance and durability, making them ideal for cutting and drilling equipment.
67
Steel products can also be divided by their shapes and related applications:
Long/Tubular Products include bars and rods, rails, wires, angles, pipes, and shapes and
sections. These products are commonly used in the automotive and construction sectors.
Flat Products include plates, sheets, coils and strips. These materials are mainly used in
automotive parts, appliances, packaging, shipbuilding, and construction.
Other Products include valves, fittings, and flanges and are mainly used as piping
materials.
Cast iron
Cast iron is iron or a ferrous alloy which has been heated until it liquefies, and is then poured
into a mould to solidify. It is usually made from pig iron. The alloy constituents affect its colour
when fractured: white cast iron has carbide impurities which allow cracks to pass straight
through. Grey cast iron has graphite flakes which deflect a passing crack and initiate countless
new cracks as the material breaks.
Carbon (C) and silicon (Si) are the main alloying elements, with the amount ranging from 2.14
wt% and 13 wt%, respectively. Iron alloys with less carbon content are known as steel. While
this technically makes these base alloys ternary FeCSi alloys, the principle of cast iron
solidification is understood from the binary ironcarbon phase diagram. Since the compositions
of most cast irons are around the eutectic point of the ironcarbon system, the melting
temperatures closely correlate, usually ranging from 1,150 to 1,200 C (2,100 to 2,190 F),
which is about 300 C (572 F) lower than the melting point of pure iron.
Cast iron's properties are changed by adding various alloying elements, or alloyants. Next to
carbon, silicon is the most important alloying because it forces carbon out of solution. Instead the
carbon forms graphite which results in a softer iron, reduces shrinkage, lowers strength, and
decreases density. Sulfur, when present, forms iron sulfide, which prevents the formation of
graphite and increases hardness. The problem with sulfur is that it makes molten cast iron
sluggish, which causes short run defects. To counter the effects of sulfur, manganese is added
because the two form into manganese sulfide instead of iron sulfide. The manganese sulfide is
lighter than the melt so it tends to float out of the melt and into the slag. The amount of
manganese required to neutralize sulfur is 1.7 sulfur content + 0.3%. If more than this amount
68
of manganese is added, then manganese carbide forms, which increases hardness and chilling,
except in grey iron, where up to 1% of manganese increases strength and density.
Nickel is one of the most common alloying elements because it refines the pearlite and graphite
structure, improves toughness, and evens out hardness differences between section thicknesses.
Chromium is added in small amounts to the ladle to reduce free graphite, produce chill, and
because it is a powerful carbide stabilizer; nickel is often added in conjunction. A small amount
of tin can is added as a substitute for 0.5% chromium. Copper is added in the ladle or in the
furnace, on the order of 0.52.5%, to decrease chill, refine graphite, and increase fluidity.
Molybdenum is added on the order of 0.31% to increase chill and refine the graphite and
pearlite structure; it is often added in conjunction with nickel, copper, and chromium to form
high strength irons. Titanium is added as a degasser and deoxidizer, but it also increases fluidity.
0.150.5% vanadium is added to cast iron to stabilize cementite, increase hardness, and increase
resistance to wear and heat. 0.10.3% zirconium helps to form graphite, deoxidize, and increase
fluidity.
In malleable iron melts, bismuth is added, on the scale of 0.0020.01%, to increase how much
silicon can be added. In white iron, boron is added to aid in the production of malleable iron; it
also reduces the coarsening effect of bismuth.
Grey cast iron
Grey cast iron is characterised by its graphitic microstructure, which causes fractures of the
material to have a grey appearance. It is the most commonly used cast iron and the most widely
used cast material based on weight. Most cast irons have a chemical composition of 2.54.0%
carbon, 13% silicon, and the remainder is iron. Grey cast iron has less tensile strength and
shock resistance than steel, but its compressive strength is comparable to low and medium
carbon steel.
White cast iron
It is the cast iron that displays white fractured surface due to the presence of cementite. With a
lower silicon content (graphitizing agent) and faster cooling rate, the carbon in white cast iron
precipitates out of the melt as the metastable phase cementite, Fe3C, rather than graphite. The
69
cementite which precipitates from the melt forms as relatively large particles, usually in a
eutectic mixture, where the other phase is austenite (which on cooling might transform to
martensite). These eutectic carbides are much too large to provide precipitation hardening (as in
some steels, where cementite precipitates might inhibit plastic deformation by impeding the
movement of dislocations through the ferrite matrix). Rather, they increase the bulk hardness of
the cast iron simply by virtue of their own very high hardness and their substantial volume
fraction, such that the bulk hardness can be approximated by a rule of mixtures. In any case, they
offer hardness at the expense of toughness. Since carbide makes up a large fraction of the
material, white cast iron could reasonably be classified as a cermet. White iron is too brittle for
use in many structural components, but with good hardness and abrasion resistance and relatively
low cost, it finds use in such applications as the wear surfaces (impeller and volute) of slurry
pumps, shell liners and lifter bars in ball mills and autogenous grinding mills, balls and rings in
coal pulverisers, and the teeth of a backhoe's digging bucket (although cast medium-carbon
martensitic steel is more common for this application).
It is difficult to cool thick castings fast enough to solidify the melt as white cast iron all the way
through. However, rapid cooling can be used to solidify a shell of white cast iron, after which the
remainder cools more slowly to form a core of grey cast iron. The resulting casting, called a
chilled casting, has the benefits of a hard surface and a somewhat tougher interior.
High-chromium white iron alloys allow massive castings (for example, a 10-tonne impeller) to
be sand cast, i.e., a high cooling rate is not required, as well as providing impressive abrasion
resistance. These high-chromium alloys attribute their superior hardness to the presence of
chromium carbides. The main form of these carbides are the eutectic or primary M7C3 carbides,
where "M" represents iron or chromium and can vary depending on the alloy's composition. The
eutectic carbides form as bundles of hollow hexagonal rods and grow perpendicular to the to the
hexagonal basal plane. The hardness of these carbides are within the range of 1500-1800HV
Malleable cast iron
Malleable iron starts as a white iron casting that is then heat treated at about 900 C (1,650 F).
Graphite separates out much more slowly in this case, so that surface tension has time to form it
into spheroidal particles rather than flakes. Due to their lower aspect ratio, spheroids are
70
relatively short and far from one another, and have a lower cross section vis-a-vis a propagating
crack or phonon. They also have blunt boundaries, as opposed to flakes, which alleviates the
stress concentration problems faced by grey cast iron. In general, the properties of malleable cast
iron are more like mild steel. There is a limit to how large a part can be cast in malleable iron,
since it is made from white cast iron.
Ductile cast iron
A more recent development is nodular or ductile cast iron. Tiny amounts of magnesium or
cerium added to these alloys slow down the growth of graphite precipitates by bonding to the
edges of the graphite planes. Along with careful control of other elements and timing, this allows
the carbon to separate as spheroidal particles as the material solidifies. The properties are similar
to malleable iron, but parts can be cast with larger sections.
TYPICAL USES
Cast iron is used in a wide variety of structural and decorative applications, because it is
relatively inexpensive, durable and easily cast into a variety of shapes. Most of the typical uses
include:
historic markers and plaques
hardware: hinges, latches
columns, balusters
stairs
structural connectors in buildings and monuments
decorative features
fences
tools and utensils
ordnance
stoves and firebacks
piping.
The basic cast iron material in all of these applications may appear to be the same, or very
similar, however, the component size, composition, use, condition, relationship to adjacent
71
materials, exposure and other factors may dictate that different treatments be used to correct
similar problems. Any material in question should be evaluated as a part of a larger system and
treatment plans should be based upon consideration of all relevant factors.
Heat Treatment
Heat Treatment is the controlled heating and cooling of metals to alter their physical and
mechanical properties without changing the product shape. Heat treatment is sometimes done
inadvertently due to manufacturing processes that either heat or cool the metal such as welding
or forming. Heat Treatment is often associated with increasing the strength of material, but it can
also be used to alter certain manufacturability objectives such as improve machining, improve
formability, restore ductility after a cold working operation. Thus it is a very enabling
manufacturing process that can not only help other manufacturing process, but can also improve
product performance by increasing strength or other desirable characteristics.
Steels are particularly suitable for heat treatment, since they respond well to heat treatment and
the commercial use of steels exceeds that of any other material. Steels are heat treated for one of
the following reasons:
1. Softening
2. Hardening
3. Material modification
Softening: Softening is done to reduce strength or hardness, remove residual stresses, improve
toughness, restore ductility, refine grain size or change the electromagnetic properties of the
steel. Restoring ductility or removing residual stresses is a necessary operation when a large
amount of cold working is to be performed, such as in a cold-rolling operation or wiredrawing.
Annealing full Process, spheroidizing, normalizing and tempering
austempering,
72
content then the steel can be directly hardened. Otherwise the surface of the part has to be
Carbon enriched using some diffusion treatment hardening techniques.
Material Modification: Heat treatment is used to modify properties of materials in addition to
hardening and softening. These processes modify the behavior of the steels in a beneficial
manner to maximize service life, e.g., stress relieving, or strength properties, e.g., cryogenic
treatment, or some other desirable properties
Full annealing is the process of slowly raising the temperature about 50 C (90 F) above the
Austenitic temperature line A3 or line ACM in the case of Hypoeutectoid steels (steels with <
0.77% Carbon) and 50 C (90 F) into the Austenite-Cementite region in the case of
Hypereutectoid steels (steels with > 0.77% Carbon).
It is held at this temperature for sufficient time for all the material to transform into Austenite or
Austenite-Cementite as the case may be. It is then slowly cooled at the rate of about 20 C/hr (36
F/hr) in a furnace to about 50 C (90 F) into the Ferrite-Cementite range. At this point, it can be
cooled in room temperature air with natural convection. The grain structure has coarse Pearlite
73
with ferrite or Cementite (depending on whether hypo or hyper eutectoid). The steel becomes
soft and ductile.
Normalizing is the process of raising the temperature to over 60 C (108 F), above line A3 or
line ACM fully into the Austenite range. It is held at this temperature to fully convert the structure
into Austenite, and then removed form the furnace and cooled at room temperature under natural
convection. This results in a grain structure of fine Pearlite with excess of Ferrite or Cementite.
The resulting material is soft; the degree of softness depends on the actual ambient conditions of
cooling. This process is considerably cheaper than full annealing since there is not the added cost
of controlled furnace cooling.
Process Annealing is used to treat work-hardened parts made out of low-Carbon steels (< 0.25%
Carbon). This allows the parts to be soft enough to undergo further cold working without
fracturing. Process annealing is done by raising the temperature to just below the FerriteAustenite region, line A1on the diagram. This temperature is about 727 C (1341 F) so heating it
to about 700 C (1292 F) should suffice. This is held long enough to allow recrystallization of
the ferrite phase, and then cooled in still air. Since the material stays in the same phase through
out the process, the only change that occurs is the size, shape and distribution of the grain
structure. This process is cheaper than either full annealing or normalizing since the material is
not heated to a very high temperature or cooled in a furnace.
Stress Relief Anneal is used to reduce residual stresses in large castings, welded parts and coldformed parts. Such parts tend to have stresses due to thermal cycling or work hardening. Parts
are heated to temperatures of up to 600 - 650 C (1112 - 1202 F), and held for an extended time
(about 1 hour or more) and then slowly cooled in still air.
Spheroidization is an annealing process used for high carbon steels (Carbon > 0.6%) that will
be machined or cold formed subsequently. This is done by one of the following ways:
Heat the part to a temperature just below the Ferrite-Austenite line, line A1 or below the
Austenite-Cementite line, essentially below the 727 C (1340 F) line. Hold the temperature for a
prolonged time and follow by fairly slow cooling. Or
74
Cycle multiple times between temperatures slightly above and slightly below the 727 C (1340
F) line, say for example between 700 and 750 C (1292 - 1382 F), and slow cool. Or
For tool and alloy steels heat to 750 to 800 C (1382-1472 F) and hold for several hours
followed by slow cooling.
All these methods result in a structure in which all the Cementite is in the form of small globules
(spheroids) dispersed throughout the ferrite matrix. This structure allows for improved
machining in continuous cutting operations such as lathes and screw machines. Spheroidization
also improves resistance to abrasion.
Tempering is a process done subsequent to quench hardening. Quench-hardened parts are often
too brittle. This brittleness is caused by a predominance of Martensite. This brittleness is
removed by tempering. Tempering results in a desired combination of hardness, ductility,
toughness, strength, and structural stability. Tempering is not to be confused with tempers on
rolled stock-these tempers are an indication of the degree of cold work performed.
The mechanism of tempering depends on the steel and the tempering temperature. The prevalent
Martensite is a somewhat unstable structure. When heated, the Carbon atoms diffuse from
Martensite to form a carbide precipitate and the concurrent formation of Ferrite and Cementite,
which is the stable form. Tool steels for example, lose about 2 to 4 points of hardness on the
Rockwell C scale. Even though a little strength is sacrificed, toughness (as measured by impact
strength) is increased substantially. Springs and such parts need to be much tougher these are
tempered to a much lower hardness.
Tempering is done immediately after quench hardening. When the steel cools to about 40 C
(104 F) after quenching, it is ready to be tempered. The part is reheated to a temperature of 150
to 400 C (302 to 752 F). In this region a softer and tougher structure Troostite is formed.
Alternatively, the steel can be heated to a temperature of 400 to 700 C (752 to 1292 F) that
results in a softer structure known as Sorbite. This has less strength than Troostite but more
ductility and toughness.
75
The heating for tempering is best done by immersing the parts in oil, for tempering upto 350 C
(662 F) and then heating the oil with the parts to the appropriate temperature. Heating in a bath
also ensures that the entire part has the same temperature and will undergo the same tempering.
For temperatures above 350 C (662 F) it is best to use a bath of nitrate salts. The salt baths can
be heated upto 625 C (1157 F). Regardless of the bath, gradual heating is important to avoid
cracking the steel. After reaching the desired temperature, the parts are held at that temperature
for about 2 hours, then removed from the bath and cooled in still air.
Hardening
Hardness is a function of the Carbon content of the steel. Hardening of a steel requires a change
in structure from the body-centered cubic structure found at room temperature to the facecentered cubic structure found in the Austenitic region. The steel is heated to Autenitic region.
When suddenly quenched, the Martensite is formed. This is a very strong and brittle structure.
When slowly quenched it would form Austenite and Pearlite which is a partly hard and partly
soft structure. When the cooling rate is extremely slow then it would be mostly Pearlite which is
extremely soft.
Usually when hot steel is quenched, most of the cooling happens at the surface, as does the
hardening. This propagates into the depth of the material. Alloying helps in the hardening and by
determining the right alloy one can achieve the desired properties for the particular application.
76
Quench Media
Water: Quenching can be done by plunging the hot steel in water. The water adjacent to the hot
steel vaporizes, and there is no direct contact of the water with the steel. This slows down
cooling until the bubbles break and allow water contact with the hot steel. As the water contacts
and boils, a great amount of heat is removed from the steel. With good agitation, bubbles can be
prevented from sticking to the steel, and thereby prevent soft spots.
Water is a good rapid quenching medium, provided good agitation is done. However, water is
corrosive with steel, and the rapid cooling can sometimes cause distortion or cracking.
Salt Water: Salt water is a more rapid quench medium than plain water because the bubbles are
broken easily and allow for rapid cooling of the part. However, salt water is even more corrosive
than plain water, and hence must be rinsed off immediately.
Oil: Oil is used when a slower cooling rate is desired. Since oil has a very high boiling point, the
transition from start of Martensite formation to the finish is slow and this reduces the likelihood
of cracking. Oil quenching results in fumes, spills, and sometimes a fire hazard.
Precipitation hardening is achieved by:
77
1. solution heat treatment where all the solute atoms are dissolved to form a single-phase
solution.
2. rapid cooling across the solvus line to exceed the solubility limit. This leads to a
supersaturated solid solution that remains stable (metastable) due to the low temperatures,
which prevent diffusion.
3. precipitation heat treatment where the supersaturated solution is heated to an intermediate
temperature to induce precipitation and kept there for some time (aging). If the process is
continued for a very long time, eventually the hardness decreases. This is called over aging.
The requirements for precipitation hardening are:
Precipitation Hardening
Hardening can be enhanced by extremely small precipitates that hinder dislocation motion. The
precipitates form when the solubility limit is exceeded. Precipitation hardening is also called age
hardening because it involves the hardening of the material over a prolonged time.
Case Hardening
Case hardening produces a hard, wear-resistant sur- face or case over a strong, tough core. The
principal forms of casehardening are carburizing, cyaniding, and nitriding. Only ferrous
metals are case-hardened. Case hardening is ideal for parts that require a wear-resistant surface
and must be tough enough interally to withstand heavy loading. The steels best suited for case
hardening are the low-carbon and low-alloy series. When high-carbon steels are case hardened,
the hardness penetrates the core and causes brittleness. In case hardening, you change the surface
of the metal chemically by introducing a high carbide or nitride content. The core remains
chemically unaffected. When heat-treated, the high-carbon surface responds to hardening, and
the core toughens.
78
Carburizing
Carburizing is a case-harden- ing process by which carbon is added to the surface of low-carbon
steel. This results in a carburized steel that has a high-carbon surface and a low-carbon interior.
When the carburized steel is heat-treated, the case be- comes hardened and the core remains
soft and tough. Two methods are used for carburizing steel. One method consists of heating the
steel in a furnace containing a carbon monoxide atmosphere. The other method has the steel
placed in a container packed with charcoal or some other carbon-rich material and then heated
in a furnace. To cool the parts, you can leave the container in the furnace to cool or remove it and
let it air cool. In both cases, the parts become annealed during the slow cooling. The depth
of the carbon penetration depends on the length of the soaking period. With to- days
methods, carburizing is almost exclusively done by gas atmospheres.
Cyaniding
This process is a type of case hardening that is fast and efficient. Preheated steel is dipped into a
heated cyanide bath and allowed to soak. Upon removal, it is quenched and then rinsed to
remove any residual cyanide. This process produces a thin, hard shell that is harder than the one
produced by carburizing and can be completed in 20 to 30 minutes vice several hours. The major
drawback is that cyanide salts are a deadly poison.
Nitriding
This case-hardening method produces the hardest surface of any of the hardening processes. It
differs from the other methods in that the individual parts have been heat-treated and tempered
before nitriding. The parts are then heated in a furnace that has an ammonia gas atmosphere. No
quenching is required so there is no worry about warping or other types of distortion. This
process is used to case harden items, such as gears, cylinder sleeves, camshafts and other engine
parts, that need to be wear resistant and operate in high-heat areas.
Flame Hardening
Flame hardening is another procedure that is used to harden the surface of metal parts. When you
use an oxyacetylene flame, a thin layer at the surface of the part is rapidly heated to its critical
temperature and then immediately quenched by a combination of a water spray and the cold base
metal. This process produces a thin, hardened surface, and at the same time, the internal parts
79
retain their original properties. Whether the process is manual or mechanical, a close watch must
be maintained, since the torches heat the metal rapidly and the temperatures are usually
determined visually. Flame hardening may be either manual or automatic. Automatic equipment
produces uniform results and is more desirable. Most automatic machines have variable travel
speeds and can be adapted to parts of various sizes and shapes. The size and shape of the
torch depends on the part. The torch consists of a mixing head, straight extension tube, 90-degree
extension head, an adjustable yoke, and a water-cooled tip. Practically any shape or size flamehardening tip is available. Tips are produced that can be used for hardening flats, rounds, gears,
cams, cylinders, and other regular or irregular shapes. In hardening localized areas, you
should heat the metal with a standard hand-held welding torch. Adjust the torch flame to neutral
for normal heating; however, in corners and grooves, use a slightly oxidizing flame to keep the
torch from sputtering. You also should particularly guard against overheating in comers and
grooves. If dark streaks appear on the metal surface, this is a sign of overheating, and you need
to increase the distance between the flame and the metal. For the best heating results, hold the
torch with the tip of the inner cone about an eighth of an inch from the surface and direct the
flame at right angles to the metal. Sometimes it is necessary to change this angle to obtain better
results; however, you rarely find a deviation of more than 30 degrees. Regulate the speed of
torch travel according to the type of metal, the mass and shape of the part, and the depth of
hardness
desired.
In
addition,
you
must
select
the
steel
according
to
the
properties desired. Select carbon steel when surface hardness is the primary factor and alloy
steel when the physical properties of the core are also factors. Plain carbon steels
should contain more than 0.35% carbon for good results inflame hardening. For water
quench- ing, the effective carbon range is from 0.40% to 0.70%. Parts with a carbon content of
more than 0.70% are likely to surface crack unless the heating and quenching rate
are carefully controlled. The surface hardness of a flame-hardened section is equal to a section
that was hardened by furnace heating and quenching. The decrease in hardness between the case
and the core is gradual. Since the core is not affected by flame hardening, there is little danger
of spalling or flaking while the part is in use. Thus flame hardening produces a hard case that is
highly
resistant
to
wear
and
core
that
retains
its
original
properties.
Flame hardening can be divided into five general methods: stationary, circular band
progressive, straight- line progressive, spiral band progressive, and circular band spinning.
80
Diffusion
Diffusion Mechanisms
Diffusion is the process of mass flow in which atoms change their positions relative to neighbors
in a given phase under the influence of thermal and a gradient. The gradient can be a
compositional gradient, an electric or magnetic gradient, or stress gradient. Many reactions in
solids and liquids are diffusion dependent. Diffusion is very important in many industrial and
domestic applications. E.g.: Carburizing the steel, annealing homogenization after solidification,
coffee mixing, etc. From an atomic perceptive, diffusion is a step wise migration of atoms from
one lattice position to another. Migration of atoms in metals/alloys can occur in many ways, and
thus corresponding diffusion mechanism is defined.
Atom diffusion can occur by the motion of vacancies (vacancy diffusion) or impurities (impurity
diffusion). The energy barrier is that due to nearby atoms which need to move to let the atoms go
by. This is more easily achieved when the atoms vibrate strongly, that is, at high temperatures.
There is a difference between diffusion and net diffusion. In a homogeneous material, atoms also
diffuse but this motion is hard to detect. This is because atoms move randomly and there will be
an equal number of atoms moving in one direction than in another. In inhomogeneous materials,
the effect of diffusion is readily seen by a change in concentration with time. In this case there is
a net diffusion. Net diffusion occurs because, although all atoms are moving randomly, there are
more atoms moving in regions where their concentration is higher.
81
Steady-State Diffusion
The flux of diffusing atoms, J, is expressed either in number of atoms per unit area and per unit
time (e.g., atoms/m2-second) or in terms of mass flux (e.g., kg/m2-second).Steady state diffusion
means that J does not depend on time. In this case, Ficks first law holds that the flux along
direction x is:
J = D dC/dx
Where dC/dx is the gradient of the concentration C, and D is the diffusion constant. The
concentration gradient is often called the driving force in diffusion (but it is not a force in the
mechanistic sense). The minus sign in the equation means that diffusion is down the
concentration gradient.
Nonsteady-State Diffusion
This is the case when the diffusion flux depends on time, which means that a type of atoms
accumulates in a region or that it is depleted from a region (which may cause them to accumulate
in another region).
82
open directions. Similar to the case of vacancy formation, the effect of temperature in diffusion
is given by a Boltzmann factor: D = D0 exp(Qd/kT).
The copper tubing used in water plumbing in Pyramids was found in serviceable
condition after more than 5,000 years.
Applications
Excellent thermal conductivity Copper cookware most highly regarded fast and uniform
heating.
Copper Alloys
Brasses and Bronzes are most commonly used alloys of Cu. Brass is an alloy with Zn.
Bronzes contain tin, aluminum, silicon or beryllium.
Other copper alloy families include copper-nickels and nickel silvers. More than 400 copperbase alloys are recognized.
Applications
Electrical wires,
roofing, nails, rivets
Automotive radiator
core, lamp fixture,
83
clutch disk,
diaphragm, fuse clips,
springs
Furniture, radiator
fittings, battery clamps,
light fixtures
Bearings, bushings,
valve seats and guards
Electrical, valves,
pumps
Condenser, heat exchanger
piping,
valves
Tin bronze Sn,
Bearings, bushing,
piston rings, gears
Aluminum
Aluminum is a light metal & easily machinable; has wide variety of surface finishes; good
electrical and thermal conductivities; highly reflective to heat and light.
Versatile metal - can be cast, rolled, stamped, drawn, spun, roll-formed, hammered, extruded
and forged into many shapes.
Al and its alloys - high strength-to-weight ratio (high specific strength) owing to low density.
Such materials are widely used in aerospace and automotive applications where weight
savings are needed for better fuel efficiency and performance.
84
Al-Li alloys are lightest among all Al alloys and find wide applications in the aerospace
industry.
85
Zinc
Zinc (symbol Zn), in commerce also spelter, is a metallic chemical element. It has atomic
number 30. It is the first element of group 12 of the periodic table. In some respects zinc is
chemically similar to magnesium: its ion is of similar size and its only common oxidation state is
+2. Zinc is the 24th most abundant element in the Earth's crust and has five stable isotopes. The
most common zinc ore is sphalerite (zinc blende), a zinc sulfide mineral. The largest mineable
amounts are found in Australia, Asia, and the United States. Zinc production includes froth
flotation of the ore, roasting, and final extraction using electricity (electrowinning).
Brass, which is an alloy of copper and zinc, has been used since at least the 10th century BC in
Judea and by the 7th century BC in Ancient Greece. Zinc metal was not produced on a large
scale until the 12th century in India and was unknown to Europe until the end of the 16th
century. The mines of Rajasthan have given definite evidence of zinc production going back to
6th century BC. To date, the oldest evidence of pure zinc comes from Zawar, in Rajasthan, as
early as the 9th century AD when a distillation process was employed to make pure zinc.
Alchemists burned zinc in air to form what they called "philosopher's wool" or "white snow".
Applications
Major applications of zinc include
Galvanizing (55%)
Alloys (21%)
Miscellaneous (8%)
The metal is most commonly used as an anti-corrosion agent. Galvanization, which is the coating
of iron or steel to protect the metals against corrosion, is the most familiar form of using zinc in
this way. In 2009 in the United States, 55% or 893 thousand tonnes of the zinc metal was used
for galvanization.
Zinc is more reactive than iron or steel and thus will attract almost all local oxidation until it
completely corrodes away. A protective surface layer of oxide and carbonate forms as the zinc
corrodes. This protection lasts even after the zinc layer is scratched but degrades through time as
86
the zinc corrodes away. The zinc is applied electrochemically or as molten zinc by hot-dip
galvanizing or spraying. Galvanization is used on chain-link fencing, guard rails, suspension
bridges, light posts, metal roofs, heat exchangers, and car bodies.
The relative reactivity of zinc and its ability to attract oxidation to itself makes it an efficient
sacrificial anode in catholic protection (CP). For example, cathodic protection of a buried
pipeline can be achieved by connecting anodes made from zinc to the pipe. Zinc acts as the
anode (negative terminus) by slowly corroding away as it passes electric current to the steel
pipeline. Zinc is also used to catholically protect metals that are exposed to sea water from
corrosion. A zinc disc attached to a ship's iron rudder will slowly corrode while the rudder stays
unattacked. Other similar uses include a plug of zinc attached to a propeller or the metal
protective guard for the keel of the ship.
With a standard electrode potential (SEP) of 0.76 volts, zinc is used as an anode material for
batteries. (More reactive lithium (SEP 3.04 V) is used for anodes in lithium batteries ).
Powdered zinc is used in this way in alkaline batteries and sheets of zinc metal form the cases for
and act as anodes in zinccarbon batteries.[98][99] Zinc is used as the anode or fuel of the zincair battery/fuel cell. The zinc-cerium redox flow battery also relies on a zinc-based negative halfcell.
Alloys
A widely used alloy which contains zinc is brass, in which copper is alloyed with anywhere from
3% to 45% zinc, depending upon the type of brass. Brass is generally more ductile and stronger
than copper and has superior corrosion resistance.These properties make it useful in
communication equipment, hardware, musical instruments, and water valves.
Other widely used alloys that contain zinc include nickel silver, typewriter metal, soft and
aluminium solder, and commercial bronze. Zinc is also used in contemporary pipe organs as a
substitute for the traditional lead/tin alloy in pipes.[104] Alloys of 8588% zinc, 410% copper,
and 28% aluminium find limited use in certain types of machine bearings. Zinc is the primary
metal used in making American one cent coins since 1982.The zinc core is coated with a thin
layer of copper to give the impression of a copper coin. In 1994, 33,200 tonnes (36,600 short
tons) of zinc were used to produce 13.6 billion pennies in the United States. Alloys of primarily
87
zinc with small amounts of copper, aluminium, and magnesium are useful in die casting as well
as spin casting, especially in the automotive, electrical, and hardware industries. These alloys are
marketed under the name Zamak. An example of this is zinc aluminium. The low melting point
together with the low viscosity of the alloy makes the production of small and intricate shapes
possible. The low working temperature leads to rapid cooling of the cast products and therefore
fast assembly is possible. Another alloy, marketed under the brand name Prestal, contains 78%
zinc and 22% aluminium and is reported to be nearly as strong as steel but as malleable as
plastic. This superplasticity of the alloy allows it to be molded using die casts made of ceramics
and cement.
Similar alloys with the addition of a small amount of lead can be cold-rolled into sheets. An alloy
of 96% zinc and 4% aluminium is used to make stamping dies for low production run
applications for which ferrous metal dies would be too expensiveIn building facades, roofs or
other applications in which zinc is used as sheet metal and for methods such as deep drawing,
roll forming or bending, zinc alloys with titanium and copper are usedUnalloyed zinc is too
brittle for these kinds of manufacturing processes.
As a dense, inexpensive, easily worked material, zinc is used as a lead replacement. In the wake
of lead concerns, zinc appears in weights for various applications ranging from fishing to tire
balances and flywheels.
Cadmium zinc telluride (CZT) is a semi conductive alloy that can be divided into an array of
small sensing devices. These devices are similar to an integrated circuit and can detect the energy
of incoming gamma ray photons. When placed behind an absorbing mask, the CZT sensor array
can also be used to determine the direction of the rays.
Other industrial uses
Zinc oxide is used as a white pigment in paints. Roughly one quarter of all zinc output in the
United States (2009), is consumed in the form of zinc compounds; a variety of which are used
industrially. Zinc oxide is widely used as a white pigment in paints, and as a catalyst in the
manufacture of rubber. It is also used as a heat disperser for the rubber and acts to protect its
polymers from ultraviolet radiation (the same UV protection is conferred to plastics containing
zinc oxide) The semiconductor properties of zinc oxide make it useful invaristors and
88
photocopying products. The zinc zinc-oxide cycle is a two step thermochemical process based on
zinc and zinc oxide for hydrogen production.
Zinc chloride is often added to lumber as a fire retardant and can be used as a wood preservative.
It is also used to make other chemicals.
Crystals of ZnS are used in lasers that operate in the mid-infrared part of the spectrum. Zinc
sulfate is a chemical in dyes and pigments. Zinc pyrithione is used in antifouling paints.
Zinc powder is sometimes used as a propellant in model rockets. When a compressed mixture of
70% zinc and 30% sulfur powder is ignited there is a violent chemical reaction. This produces
zinc sulfide, together with large amounts of hot gas, heat, and light. Zinc sheet metal is used to
make zinc bars.
Zn, the most abundant isotope of zinc, is very susceptible to neutron activation, being transmuted
into the highly radioactive
Zn, which has a half-life of 244 days and produces intense gamma radiation. Because of this,
Zinc Oxide used in nuclear reactors as an anti-corrosion agent is depleted of
Zn before use, this is calleddepleted zinc oxide. For the same reason, zinc has been proposed as a
salting material for nuclear weapons (cobalt is another, better-known salting material). A jacket
of isotopically enriched
Zn would be irradiated by the intense high-energy neutron flux from an exploding thermonuclear
weapon, forming a large amount of
Zn significantly increasing the radioactivity of the weapon's fallout. Such a weapon is not known
to have ever been built, tested, or used.
Zn is also used as a tracer to study how alloys that contain zinc wear out, or the path and the role
of zinc in organisms.
Chromium
Chromium is a chemical element which has the symbol Cr and atomic number 24. It is the first
element in Group 6. It is a steely-gray, lustrous, hard and brittle metal which takes a high polish,
89
resists tarnishing, and has a high melting point. Chromium oxide was used by the Chinese in the
Qin dynasty over 2,000 years ago to coat metal weapons found with the Terracotta Army.
Chromium was discovered as an element after it came to the attention of the western world in the
red crystalline mineral crocoite (lead(II) chromate), discovered in 1761 and initially used as a
pigment. Louis Nicolas Vauquelin first isolated chromium metal from this mineral in 1797.
Since Vauquelin's first production of metallic chromium, small amounts of native (free)
chromium metal have been discovered in rare minerals, but these are not used commercially.
Instead, nearly all chromium is commercially extracted from the single commercially viable
orechromite, which is iron chromium oxide Chromite is also now the chief source of chromium
for chromium pigments.
Applications
The strengthening effect of forming stable metal carbides at the grain boundaries and the strong
increase in corrosion resistance made chromium an important alloying material for steel. The
high-speed tool steels contain between 3 and 5% chromium. Stainless steel, the main corrosionproof metal alloy, is formed when chromium is added to iron in sufficient concentrations, usually
above 11%. For its formation, ferrochromium is added to the molten iron. Also nickel-based
alloys increase in strength due to the formation of discrete, stable metal carbide particles at the
grain boundaries. For example, Inconel 718 contains 18.6% chromium. Because of the excellent
high-temperature properties of these nickel superalloys, they are used in jet engines and gas
turbines in lieu of common structural materials.
The relative high hardness and corrosion resistance of unalloyed chromium makes it a good
surface coating, being still the most "popular" metal coating with unparalleled combined
durability. A thin layer of chromium is deposited on pretreated metallic surfaces by
electroplating techniques. There are two deposition methods: Thin, below 1 m thickness, layers
are deposited by chrome plating, and are used for decorative surfaces. If wear-resistant surfaces
are needed then thicker chromium layers are deposited. Both methods normally use acidic
chromate or dichromate solutions. To prevent the energy-consuming change in oxidation state,
the use of chromium(III) sulfate is under development, but for most applications, the established
process is used.
90
In the chromate conversion coating process, the strong oxidative properties of chromates are
used to deposit a protective oxide layer on metals like aluminium, zinc and cadmium. This
passivation and the self-healing properties by the chromate stored in the chromate conversion
coating, which is able to migrate to local defects, are the benefits of this coating methodBecause
of environmental and health regulations on chromates, alternative coating method are under
development.
Anodizing of aluminium is another electrochemical process, which does not lead to the
deposition of chromium, but uses chromic acid as electrolyte in the solution. During anodization,
an oxide layer is formed on the aluminium. The use of chromic acid, instead of the normally
used sulfuric acid, leads to a slight difference of these oxide layers. The high toxicity of Cr(VI)
compounds, used in the established chromium electroplating process, and the strengthening of
safety and environmental regulations demand a search for substitutes for chromium or at least a
change to less toxic chromium(III) compounds.
Dye and pigment
The mineral crocoite (lead chromate PbCrO4) was used as a yellow pigment shortly after its
discovery. After a synthesis method became available starting from the more abundant chromite,
chrome yellow was, together with cadmium yellow, one of the most used yellow pigments.
Chromium oxides are also used as a green color in glassmaking and as a glaze in ceramics.
Green chromium oxide is extremely light-fast and as such is used in cladding coatings. It is also
the main ingredient in IR reflecting paints, used by the armed forces, to paint vehicles, to give
them the same IR reflectance as green leaves.
Synthetic ruby and the first laser
Natural rubies are corundum (aluminum oxide) crystals that are colored red (the rarest type) due
to chromium (III) ions (other colors of corundum gems are termedsapphires). A red-colored
artificial ruby may also be achieved by doping chromium(III) into artificial corundum crystals,
thus making chromium a requirement for making synthetic rubies
91
Wood preservative
Because of their toxicity, chromium(VI) salts are used for the preservation of wood. For
example, chromated copper arsenate (CCA) is used in timber treatment to protect wood from
decay fungi, wood attacking insects, including termites, and marine borers
Refractory material
The high heat resistivity and high melting point makes chromite and chromium(III) oxide a
material for high temperature refractory applications, like blast furnaces, cement kilns, molds for
the firing of bricks and as foundry sands for the casting of metals. In these applications, the
refractory materials are made from mixtures of chromite and magnesite. The use is declining
because of the environmental regulations due to the possibility of the formation of
chromium(VI).
Brasses & Bronzes
Brass is an alloy made of copper and zinc; the proportions of zinc and copper can be varied to
create a range of brasses with varying properties. Bronze is an alloy consisting primarily of
copper, usually with tin as the main additive. It is hard and tough, and it was so significant in
antiquity that the Bronze Age was named after the metal.
Admiralty brass contains 30% zinc, with 1% tin to inhibit dezincification in many environments.
Alpha brasses with less than 35% zinc, are malleable, can be worked cold, and are used in
pressing, forging, or similar applications. They contain only one phase, with face-centered cubic
crystal structure. Alpha-beta brass (Muntz metal), also called duplex brass, is 3545% zinc and is
suited for hot working. It contains both and ' phase; the '-phase is body-centered cubic and is
harder and stronger than . Alpha-beta brasses are usually worked hot. Aluminium brass contains
aluminium, which improves its corrosion resistance. Red brass is both an American term for the
copper-zinc-tin alloy known as gunmetal, and an alloy which is considered both a brass and a
bronze. It typically contains 85% copper, 5% tin, 5% lead, and 5% zinc.
Aluminium Bronze
A type of BRONZE in which aluminium is the main alloying metal added to copper. Small
amounts of other elements such as iron, manganese, nickel and silicon are added to impart
92
various properties such as corrosion resistance or malubility. It fairs well in the marine
enviroment.
Typical compostion:
Copper 80%
Aluminium 10%
Nickel 5%
Iron 5%
Silicon Bronze
Has small amounts of silicon to allow it to be wrought or cold worked into a stronger alloy such
as by rolling. It is also resistant to corrosion and therefore good for use in the marine enviroment.
Typical compostion:
Copper 96%
Silicon 3%
Manganase 1%
Phosphor bronze
Well this one is different! Rather than Phosphor being the main alloy metal, it is used during
manufacture to purify the melt and create a purer stronger type of bronze. Usually not more than
0.2% of the Phosphur is left in the metal. It is very corrosion resistant and therefore good in the
marine environment.
Typical compostion:
Copper 94.8%
Tin 5%
Phosphorus 0.2%
Leaded Bronze
Leaded Gunmetal (LG2) Is a type of copper alloy that has a small amount of lead, tin and zinc
added in similar quantities. It is not considered to be brass due to the amount of zinc being small.
It has widespread use as a valve and through hull fitting material due to it's good seawater
resistance. It does not de-zincify in seawater despite having a zinc content. It is good for use in
the marine environment.
93
Typical composition:
Copper 85%
Lead 5%
Tin 5%
Zinc 5%
Bronze was especially suitable for use in boat and ship fittings prior to the wide employment of
stainless steel owing to its combination of toughness and resistance to salt water corrosion.
Bronze is still commonly used in ship propellers and submerged bearings.
In the 20th century, silicon was introduced as the primary alloying element, creating an alloy
with wide application in industry and the major form used in contemporary statuary. Sculptors
may prefer silicon bronze because of the ready availability of silicon bronze brazing rod, which
allows color-matched repair of defects in castings. Aluminium is also used for the structural
metal aluminium bronze.
It is also widely used for cast bronze sculpture. Many common bronze alloys have the unusual
and very desirable property of expanding slightly just before they set, thus filling in the finest
details of a mold. Bronze parts are tough and typically used forbearings, clips, electrical
connectors and springs.
Bronze also has very low metal-on-metal friction, which made it invaluable for the building of
cannon where iron cannonballs would otherwise stick in the barrel. It is still widely used today
for springs, bearings, bushings, automobile transmission pilot bearings, and similar fittings, and
is particularly common in the bearings of small electric motors. Phosphor bronze is particularly
suited to precision-grade bearings and springs. It is also used in guitar and piano strings.
Unlike steel, bronze struck against a hard surface will not generate sparks, so it (along with
beryllium copper) is used to make hammers, mallets, wrenches and other durable tools to be used
in explosive atmospheres or in the presence of flammable vapors.
Bronze is used to make bronze wool for woodworking applications where steel wool would
discolor oak.
94
95
UNIT IV
96
Dielectric Materials
A dielectric material (dielectric for short) is an electrical insulator that can be polarized by an
applied electric field. When a dielectric is placed in an electric field, electric charges do not flow
through the material as they do in a conductor, but only slightly shift from their average
equilibrium positions causing dielectric polarization. Because of dielectric polarization, positive
charges are displaced toward the field and negative charges shift in the opposite direction. This
creates an internal electric field that reduces the overall field within the dielectric itself. If a
dielectric is composed of weakly bonded molecules, those molecules not only become polarized,
but also reorient so that their symmetry axes align to the field.
The study of dielectric properties concerns storage and dissipation of electric and magnetic
energy in materials. Dielectrics are important for explaining various phenomena in electronics,
optics, and solid-state physics.
Dielectric strength
All insulating materials fail at some level of applied voltage, and dielectric strength is the
voltage a material can withstand before breakdown occurs. Dielectric strength is measured
through the thickness of the material (taking care to avoid surface effects) and is normally
expressed as a voltage gradient (volts per unit length). Note that the voltage gradient at
breakdown is much higher for very thin test pieces (<100m thick) than for thicker sections.
The value of dielectric strength for a specimen is also influenced by its temperature and ambient
humidity, by any voids or foreign materials in the specimen, and by the conditions of test, so that
it is often difficult to compare data from different sources.
Test variables include electrode configuration and specimen geometry, and the frequency and
rate of application of the test voltage. Standard strategies include:
The short-time test, increasing the voltage from zero at a predetermined rate (usually
between 100 and 3,000V/sec) until breakdown occurs
The step-by-step test, initially applying half the short-time breakdown voltage, and then
increasing this in equal increments, holding each level for a set period of time.
97
Defects, voids, and foreign particles introduced during manufacture which lower the
dielectric strength locally, having the effect of reducing the test values as the area tested
is increased
The presence of a stress concentration at the electrode edges or points where the electric
field is higher than average.
Because of dielectric heating, which raises the temperature and lowers the breakdown
strength.
Magnetic Properties
Diamagnetism is a very weak form of magnetism that is nonpermanent and persists only while
an external field is being applied. It is induced by a change in the orbital motion of electrons due
to an applied magnetic field. The magnitude of the induced magnetic moment is extremely small
and in a direction opposite to that of the applied field. Most elements in the periodic table,
including copper, silver, and gold, are diamagnetic.
Paramagnetic material is one whose atoms do have permanent dipole moments, but the magic
of ferromagnetism is not active. If a magnetic field is applied to such a material, the dipole
moments try to line up with the magnetic field, but are prevented from becoming perfectly
aligned by their random thermal motion. Because the dipoles try to line up with the applied field,
the susceptibilities of such materials are positive, but in the absence of the strong ferromagnetic
effect, the susceptibilities are rather small, say in the range to . When a paramagnetic material is
placed in a strong magnetic field, it becomes a magnet, and as long as the strong magnetic field
is present, it will attract and repel other magnets in the usual way. But when the strong magnetic
field is removed, the net magnetic alignment is lost as the dipoles relax back to their normal
98
99
Ferrimagnetism
Some ceramics also exhibit a permanent magnetizations termed ferrimagentism. The
macroscopic magnetic characteristics of ferromagnets and ferrimagents are similar; the
distinction lies in the source of the net magnetic moments. The net ferrimagentic moment arises
from the incomplete cancellation of spin moments.
Type of Magnetism
Susceptibility
Example /
Susceptibility
-
Diamagnetism
Small &
negative.
2.74x10-
Atoms have
no magnetic
moment
Au
Cu
0.77x106
0.19x10-
Atoms have
Paramagnetism
Small &
positive.
randomly
-Sn
oriented
Pt
magnetic
Mn
moments
Large &
positive,
Ferromagnetism
function of
applied field,
microstructure
dependent.
21.04x1
0-6
66.10x1
0-6
Atoms have
parallel
Fe
aligned
magnetic
~100,00
0
moments
Atoms have
mixed parallel
Antiferromagnetism
Small &
positive.
and antiparallel
Cr
aligned
magnetic
moments
100
3.6x10-6
Large &
Atoms have
positive,
Ferrimagnetism
function of
applied field,
microstructure
dependent
anti-parallel
Ba
aligned
ferrite
magnetic
~3
moments
101
The loop is generated by measuring the magnetic flux of a ferromagnetic material while the
magnetizing force is changed. A ferromagnetic material that has never been previously
magnetized or has been thoroughly demagnetized will follow the dashed line as H is increased.
As the line demonstrates, the greater the amount of current applied (H+), the stronger the
magnetic field in the component (B+). At point "a" almost all of the magnetic domains are
aligned and an additional increase in the magnetizing force will produce very little increase in
magnetic flux. The material has reached the point of magnetic saturation. When H is reduced to
zero, the curve will move from point "a" to point "b." At this point, it can be seen that some
magnetic flux remains in the material even though the magnetizing force is zero. This is referred
to as the point of retentivity on the graph and indicates the remanence or level of residual
magnetism in the material. (Some of the magnetic domains remain aligned but some have lost
their alignment.) As the magnetizing force is reversed, the curve moves to point "c", where the
flux has been reduced to zero. This is called the point of coercivity on the curve. (The reversed
magnetizing force has flipped enough of the domains so that the net flux within the material is
zero.) The force required to remove the residual magnetism from the material is called the
coercive force or coercivity of the material.
103
As the magnetizing force is increased in the negative direction, the material will again become
magnetically saturated but in the opposite direction (point "d"). Reducing H to zero brings the
curve to point "e." It will have a level of residual magnetism equal to that achieved in the other
direction. Increasing H back in the positive direction will return B to zero. Notice that the curve
did not return to the origin of the graph because some force is required to remove the residual
magnetism. The curve will take a different path from point "f" back to the saturation point where
it with complete the loop.
From the hysteresis loop, a number of primary magnetic properties of a material can be
determined.
1. Retentivity - A measure of the residual flux density corresponding to the saturation
induction of a magnetic material. In other words, it is a material's ability to retain a
certain amount of residual magnetic field when the magnetizing force is removed after
achieving saturation. (The value of B at point b on the hysteresis curve.)
2. Residual Magnetism or Residual Flux - the magnetic flux density that remains in a
material when the magnetizing force is zero. Note that residual magnetism and retentivity
are the same when the material has been magnetized to the saturation point. However, the
level of residual magnetism may be lower than the retentivity value when the
magnetizing force did not reach the saturation level.
3. Coercive Force - The amount of reverse magnetic field which must be applied to a
magnetic material to make the magnetic flux return to zero. (The value of H at point c on
the hysteresis curve.)
4. Permeability - A property of a material that describes the ease with which a magnetic
flux is established in the component.
Magnetic Tapes: Magnetic tapes are extensively used for recording audio and video signals,
although it is unclear how long this technology will continue to be used with the rising popularity
of the digital versatile disk (DVD).
Tapes can be made with either a particulate media adhered to a plastic substrate or a metal
evaporated (ME) film on the substrate. The magnetic layer on a particulate tape is only 40%
magnetic material whereas ME tapes have a 100% magnetic layer. Therefore, ME tapes give
104
better quality recording, but they are more time consuming to produce and are more expensive.
Particulate tapes are much cheaper and hence account for the majority of magnetic tapes.
Magnetic Disks: Recording data onto a disk has obvious advantages with respect to access
times, as the head can readily be moved to the appropriate place on the disk whereas a tape
would need to be rewound or advanced. There are two types of disk: floppy and hard. The
principles of manufacturing and recording on floppy disks are very similar to that of particulate
magnetic tape, i.e. the same particulate materials on a plastic substrates.
Hard disk drives are formed on a rigid substrate, usually aluminium, which is around 2mm thick.
On to the substrate are deposited several layers: an under layer to help adhesion (~10nm nickel
phosphide); a layer of chromium (5-10nm) to control orientation and grain size of magnetic
layer; the magnetic layer (50nm PtCo with various additions of Ta, P, Ni, Cr); a protective
overcoat (e.g. 10-20nm zirconia) and finally lubricant to reduce friction and wear of the disk
(e.g. a monolayer of long chain fluorocarbons). The magnetic layer forms a cellular structure of
Co-rich magnetic cells in a non-magnetic matrix. These cells act just like particulate recording
media but on a much finer scale.
Electrical Properties
Electronic and Ionic Conduction
In metals, the current is carried by electrons, and hence the name electronic conduction. In ionic
crystals, the charge carriers are ions, thus the name ionic conduction.
Energy Band Structures in Solids
When atoms come together to form a solid, their valence electrons interact due to Coulomb
forces, and they also feel the electric field produced by their own nucleus and that of the other
atoms. In addition, two specific quantum mechanical effects happen. First, by Heisenberg's
uncertainty principle, constraining the electrons to a small volume raises their energy, this is
called promotion. The second effect, due to the Pauli Exclusion Principle, limits the number of
electrons that can have the same property (which include the energy). As a result of all these
effects, the valence electrons of atoms form wide valence bands when they form a solid. The
bands are separated by gaps, where electrons cannot exist. The precise location of the bands and
105
band gaps depends on the type of atom (e.g., Si vs. Al), the distance between atoms in the solid,
and the atomic arrangement (e.g., carbon vs. diamond).
In semiconductors and insulators, the valence band is filled, and no more electrons can be added,
following Pauli's principle. Electrical conduction requires that electrons be able to gain energy in
an electric field; this is not possible in these materials because that would imply that the electrons
are promoted into the forbidden band gap. In metals, the electrons occupy states up to the Fermi
level. Conduction occurs by promoting electrons into the conduction band, that starts at the
Fermi level, separated by the valence band by an infinitesimal amount.
Electrical Resistivity of Metals
The resistivity then depends on collisions. Quantum mechanics tells us that electrons behave like
waves. One of the effects of this is that electrons do not scatter from a perfect lattice. They
scatter by defects, which can be:
atoms displaced by lattice vibrations
vacancies and interstitials
dislocations, grain boundaries
impurities
One can express the total resistivity tot by the Matthiessen rule, as a sum of resistivities due to
thermal vibrations, impurities and dislocations. Fig. 19.8 illustrates how the resistivity increases
with temperature, with deformation, and with alloying..
Semiconductivity
Intrinsic Semiconductor
Semiconductors can be intrinsic or extrinsic. Intrinsic means that electrical conductivity does not
depend on impurities, thus intrinsic means pure. In extrinsic semiconductors the conductivity
depends on the concentration of impurities. Conduction is by electrons and holes. In an electric
field, electrons and holes move in opposite direction because they have opposite charges.
In an intrinsic semiconductor, a hole is produced by the promotion of each electron to the
conduction band. Thus:
n=p
106
Extrinsic Semiconductor
Unlike intrinsic semiconductors, an extrinsic semiconductor may have different concentrations
of holes and electrons. It is called p-type if p>n and n-type if n>p. They are made by doping, the
addition of a very small concentration of impurity atoms. Two common methods of doping are
diffusion and ion implantation. Excess electron carriers are produced by substitutional impurities
that have more valence electron per atom than the semiconductor matrix. For instance
phosphorous, with 5 valence electrons, is an electron donor in Si since only 4 electrons are used
to bond to the Si lattice when it substitutes for a Si atom. Thus, elements in columns V and VI of
the periodic table are donors for semiconductors in the IV column, Si and Ge. The energy level
of the donor state is close to the conduction band, so that the electron is promoted (ionized)
easily at room temperature, leaving a hole (the ionized donor) behind. Since this hole is unlike a
hole in the matrix, it does not move easily by capturing electrons from adjacent atoms. This
means that the conduction occurs mainly by the donated electrons (thus n-type). Excess holes are
produced by substitutional impurities that have fewer valence electrons per atom than the matrix.
This is the case of elements of group II and III in column IV semiconductors, like B in Si. The
bond with the neighbors is incomplete and so they can capture or accept electrons from adjacent
silicon atoms. They are called acceptors. The energy level of the acceptor is close to the valence
band, so that an electron may easily hop from the valence band to complete the bond leaving a
hole behind. This means that conduction occurs mainly by the holes (thus p-type).
The Temperature Variation of Conductivity and Carrier Concentration
Temperature causes electrons to be promoted to the conduction band and from donor levels, or
holes to acceptor levels. The dependence of conductivity on temperature is like other thermally
activated processes:
= A exp(Eg/2kT)
where A is a constant (the mobility varies much more slowly with temperature). Plotting ln vs.
1/T produces a straight line of slope Eg/2k from which the band gap energy can be determined.
Extrinsic semiconductors have, in addition to this dependence, one due to the thermal promotion
of electrons from donor levels or holes from acceptor levels. The dependence on temperature is
also exponential but it eventually saturates at high temperatures where all the donors are emptied
or all the acceptors are filled. This means that at low temperatures, extrinsic semiconductors have
107
larger conductivity than intrinsic semiconductors. At high temperatures, both the impurity levels
and valence electrons are ionized, but since the impurities are very low in number and they are
exhausted, eventually the behavior is dominated by the intrinsic type of conductivity.
Intrinsic semiconductor
108
Extrinsic semiconductor
Semiconductor Devices
A semiconductor diode is made by the intimate junction of a p-type and an n-type
semiconductor (an n-p junction). Unlike a metal, the intensity of the electrical current that passes
through the material depends on the polarity of the applied voltage. If the positive side of a
battery is connected to the p-side, a situation called forward bias, a large amount of current can
flow since holes and electrons are pushed into the junction region, where they recombine
(annihilate). If the polarity of the voltage is flipped, the diode operates under reverse bias. Holes
and electrons are removed from the region of the junction, which therefore becomes depleted of
carriers and behaves like an insulator. For this reason, the current is very small under reverse
bias. The asymmetric current-voltage characteristics of diodes is used to convert alternating
current into direct current. This is called rectification.
109
A p-n-p junction transistor contains two diodes back-to-back. The central region is very thin
and is called the base. A small voltage applied to the base has a large effect on the current
passing through the transistor, and this can be used to amplify electrical signals (Fig. 19.22).
Another common device is the MOSFET transistor where a gate serves the function of the base
in a junction transistor. Control of the current through the transistor is by means of the electric
field induced by the gate, which is isolated electrically by an oxide layer.
Conduction in Ionic Materials
In ionic materials, the band gap is too large for thermal electron promotion. Cation vacancies
allow ionic motion in the direction of an applied electric field, this is referred to as ionic
conduction. High temperatures produce more vacancies and higher ionic conductivity. At low
temperatures, electrical conduction in insulators is usually along the surface, due to the
deposition of moisture that contains impurity ions.
Superconductivity:
Superconductivity is the ability of certain materials to conduct electrical current with no
resistance and extremely low losses. This ability to carry large amounts of current can be applied
to electric power devices such as motors and generators, and to electricity transmission in power
lines. For example, superconductors can carry as much as 100 times the amount of electricity of
ordinary copper or aluminum wires of the same size. Scientists had been intrigued with the
concept of superconductivity since its discovery in the early 1900s, but the extreme low
temperatures the phenomenon required was a barrier to practical and low-cost applications. This
110
all changed in 1986, when a new class of ceramic superconductors was discovered that
"superconducted" at higher temperatures. The science of high-temperature superconductivity
(HTS) was born, and along with it came the prospect for an elegant technology that promises to
"supercharge" the way energy is generated, delivered, and used.
Meissner Effect & Superconductor Types
The Meissner effect is an expulsion of a magnetic field from a superconductor during its
transition to the superconducting state. T he German physicists Walther Meissner and Robert
Ochsenfeld discovered the phenomenon in 1933 by measuring the magnetic field distribution
outside superconducting tin and lead samples.
111
112
UNIT V
113
hard,
wear-resistant,
brittle,
refractory,
thermal insulators,
electrical insulators,
nonmagnetic,
oxidation resistant,
114
Chemically stable.
Of course there are many exceptions to these generalizations. For example, borosilicate glasses
(glasses that contain silica and boron as major ingredients) and certain glass ceramics (glasses
that contain a crystalline phase) and NZP ceramics are very resistant to thermal shock and are
used in applications such as ovenware, stove tops and kiln furniture respectively. Also, some
ceramics are excellent electrical conductors and an entire commercial market is based on the fact
that certain ceramics (ferrites) are magnetic.
Types and applications of ceramics:
Ceramics offer a high temperature range. However, ceramics are not very strong. To compensate
for their lack of strength ceramics are usually combined with some other material to form a
ceramic composite.
1) Glasses and glass ceramics- The glasses are a familiar group of ceramics; containers,
windows, lenses and fiberglass represent typical applications. The properties of standard vitrified
products are insufficient for architectural applications and structural building components,
insulation or other specialized applications. Yet there is an effective way to improve these
properties without major alterations to the process itself - the introduction of a controlled
crystallization process through a subsequent heat treatment, i.e. by forming a glass-ceramic.
Production of Glass-Ceramics
Glass-ceramic articles may be produced by three routes:
In the latter case, the powders are densified at relatively low temperatures by exploiting a viscous
flow sintering mechanism. After densification, the material is subjected to a crystallisation heattreatment to obtain the required glass-ceramic microstructure. Alternatively, both densification
and crystallisation may take place during a single sintering step. Along with the economic
advantage of using relatively low processing temperatures, the powder technology route is
115
suitable for the production of a range of advanced materials, including glass-ceramics with
specified porosities and glass-ceramic matrix composites.
Using the petrurgic method, the slow cooling from the molten state causes nucleation and growth
of certain crystalline phases. Therefore, the final microstructure, and hence the properties,
depends mainly on the composition and the cooling rate.
Glass-Ceramics Based on Coal Ash
The very high iron oxide content of coal ash, table 1, indicates the potential for developing
magnetic phases using appropriate processing - this was the aim of our work. We calcined the asreceived ash at 800C for two hours to remove any volatile Material compounds, including sulfur
and carbon. The powder and petrurgic methods were explored, and gave us products with
different phases and microstructures. For the sintering experiments, we mixed calcined ash
powder with various amounts (10-50wt%) of borosilicate (Pyrex) glass. The powder mixtures
were uniaxial cold pressed to a cylindrical shape and sintered in air at temperatures in the range
of 1,000-1,500C for periods of up to 15 hours. Using the petrurgic method, coal ash was mixed
with sodalime glass powder. The mixture was melted at 1,500C and cooled to room temperature
at rates of between 1-10C per minute.
Glass-Ceramic Composites
Work to date has largely concentrated on composites with a matrix of the slag-based Silceram
glass-ceramic (a glass-ceramic for floor and wall tiles and wear components). We have
investigated both particulate- (SiC and TiC) and fibre-reinforcement (SiC). Properties measured
include the fundamental mechanical properties but also more complex properties such as thermal
shock resistance and erosion resistance. As mentioned previously, the thermal shock resistance
of glass-ceramics is superior to the parent glasses, and the shock resistance is further improved
by particulate reinforcement. For example, monolithic Silceram has a thermal shock critical
temperature of 180C, whereas a 20wt%SiC composite has a value of 270C. Erosion resistance
may also be improved by particulate reinforcement, e.g., for TiC reinforced Silceram - the larger
the reinforcement particle size and the greater the volume fraction, the lower the erosion rate.
Results indicate a way for transforming vitrified silicate residues into useful products with broad
116
application potential. The glass-ceramics obtained are candidate materials for applications in
floors of industrial buildings and in construction, and for outside and inside facing walls. We are
currently addressing issues associated with the effect of environmental influences on the
chemical durability and toxic potential of the materials, which may be compromised by the
presence of heavy metals incorporated in the glass or crystalline phases. Public acceptance of the
use and exploitation of glass-ceramic-based materials in such applications will strongly depend
on a satisfactory consideration of these issues.
2) Refractories -Refractories are materials needed for handling high temperature liquids, gases
and solids, e.g., for industrial processing. Applications include solar furnaces, casting molds for
molten materials, heat exchangers, and aerobraking heat shields. Industrial refractory needs can
be satisfied by sintered calcia (CaO), silica (SiO2), magnesia (MgO), alumina (Al2O3) and titania
(TiO2), with the desired porosity. Of course, these stable materials are commonly used on Earth
for the same purposes, due to their great resistance to heat, oxidation (they are already fully
oxidized), corrosion and abrasion. Minerals such as olivine [(MgFe)2SiO4] and anorthite
(CaAl2Si2O8) are also useful for making refractory bricks and ceramics. Some refractories and
their ceramics have low expansion due to heat and are attractive for space environments where a
wide range of temperatures are experienced.
One particular application of refractories is in transportation for returning cargoes to low Earth
orbit by aerobraking with the upper atmosphere, and perhaps slowing down some incoming
asteroid payloads by aerobraking. Of course, this is the method used by spacecraft to return to
Earth, including the reusable Space Shuttle. The Space Shuttle's tiles are made from silica (SiO2)
(with a thin borosilicate coating to provide a smooth, aerodynamic surface for a smooth landing).
Aerobraking tiles are produced from amorphous silica fibers which are pressed and sintered, with
the resulting tile having as much as 93% porosity (i.e., very lightweight) and low thermal
expansion, low thermal conductivity, and good thermal shock properties. This process can be
readily performed in space when we can produce silica of the required purity. Cheaper materials
besides silica fibers can be used. Silica fibers are used on the Space Shuttle in order to keep its
weight down, thereby increasing cargo weight capacity. For resources already in space, we don't
have this economic need. A number of other materials can be used for heat shields, e.g., alumina
(Al2O3) or anorthite (CaAl2Si2O8).
117
3) Abrasives- Abrasive cements are used to wear, grind or cut away other material, which
necessarily is softer. Therefor, the prime requisite for this group of materials is hardness or wear
resistancr; in addition, a hig degree of toughness is essential to ensure that the abrasive particles
do not easily fracture. Furthermore, high temperatures may be produced from abrasive frictional
forces, so some refractoriness is also desirable. Diamonds, both natural and synthetic, are utilized
as abrasives; however, they are relatively expensive. The more common ceramic abrasives
include silicon carbide, tungsten carbide(WC), aluminium oxide and silica sand. Abrasives are
used in several forms-bonded to grinding wheels, as coated abrasives and as loose grains. Coated
abrasives are those in which an abrasive powder is coated on some type of paper or cloth
material; sandpaper is probably the mostly familiar example. Wood, metals, ceramics and
plastics are all frequently ground and polished using this form of abrasive. Grinding, lapping and
polishing wheels often employ loose abrasive grains that are delivered in some type of oil or
water based vehicle. Diamonds, corundum, silicon carbide and rouge are used in loose form over
a variety of grain size ranges.
4) Cements: Several familiar ceramic materials are classified as inorganic cements:cements,
plaster of paris, and lime, which as a group are produced in extremely large quantities. The
characteristic feature of these materials is that when mixed with water, they form a paste that
subsequently sets and hardens. This trait is especially useful in that solid and rigid structures
having just about any shape may be expeditiously formed.
Portland Cement
Portland cement is a closely controlled chemical combination of calcium, silicon, aluminum, iron
and small amounts of other compounds, to which gypsum is added in the final grinding process
to regulate the setting time of the concrete. Some of the raw materials used to manufacture
cement are limestone, shells, and chalk or marl, combined with shale, clay, slate or blast furnace
slag, silica sand, and iron ore. Lime and silica make up approximately 85 percent of the mass
The term "Portland" in Portland cement originated in 1824 when an English mason obtained a
patent for his product, which he named Portland Cement. This was because his cement blend
produced concrete that resembled the color of the natural limestone quarried on the Isle of
Portland in the English Channel. Different types of Portland cement are manufactured to meet
different physical and chemical requirements for specific purposes.
118
Common Examples
Structural clay products Brick, sewer pipe, roofing tile, clay floor and wall tile (i.e., quarry
tile), flue linings
Whitewares Dinnerware, floor and wall tile, sanitaryware, electrical porcelain, decorative
ceramics
Refractories Brick and monolithic products are used in iron and steel, non-ferrous metals, glass,
cements, ceramics, energy conversion, petroleum, and chemicals industries
Glasses Flat glass (windows), container glass (bottles), pressed and blown glass
(dinnerware), glass fibers (home insulation), and advanced/specialty glass (optical fibers)
Abrasives Natural (garnet, diamond, etc.) and synthetic (silicon carbide, diamond, fused
alumina, etc.) abrasives are used for grinding, cutting, polishing, lapping, or pressure blasting of
materials
Cements Used to produce concrete roads, bridges, buildings, dams, and the like
that cause shape distortion and differential shrinkage. Proprietary 3D, finite-element code
packing and compaction models, and process-control tools are now available to improve the
production of ceramic components. Sandia has capabilities in the areas of hydrostatic and triaxial
compaction testing to characterize materials properties, and x-ray radiography, ultrasound, and
computed tomography for density characterization. In addition, expertise in slurry processing has
enabled the development of direct-fabrication processes. Furthermore, we are developing
phenomenological sintering models to enhance both ceramic component design and
manufacturing capability.
The synthesis of the large molecular weight polymers is termed polymerization; it is simply the
process by which monomer units are joined over, to generate each of the constituent giant
molecules. The reactions by which polymerization occurs are grouped into two general
classification- addition and condensation, according to the reaction mechanisms.
Addition polymerization is a process by which bifuncational monomer units are attached one at
a time in chainlike fashion to form a linear macromolecules; the composition of the resultant
products molecule is an exact multiple for that of the original reactant monomer. Three distinct
stages- initiation, propagation and termination are involved in addition polymerization.
Condensation polymerization is the formation of polymers by stepwise intermolecular
chemical reactions that normally involve more than one monomer species; there is usually a
small molecular weight by producer such as water, which is eliminated. No reactant species has
the chemical formula of the mer repeat unit, and the intermolecular reaction occurs every time a
mer repeat unit is formed
Types of Polymers/plastics:
Thermosetting plastics (thermosets) are polymer materials that cure, through the addition of
energy, to a stronger form. The energy may be in the form of heat (generally above 200 degrees
Celsius), through a chemical reaction (two-part epoxy, for example), or irradiation.
Thermoset materials are usually liquid, powder, or malleable prior to curing, and designed to be
molded into their final form, or used as adhesives.
The curing process transforms the resin into a plastic or rubber by a cross-linking process.
Energy and/or catalysts are added that cause the molecular chains to react at chemically active
sites (unsaturated or epoxy sites, for example), linking into a rigid, 3-D structure. The crosslinking process forms a molecule with a larger molecular weight, resulting in a material with a
higher melting point. During the reaction, when the molecular weight has increased to a point so
that the melting point is higher than the surrounding ambient temperature, the material forms into
a solid material. Subsequent uncontrolled reheating of the material results in reaching the
decomposition temperature before the melting point is obtained. A thermoset material cannot be
melted and re-shaped after it is cured.
121
Thermoset materials are generally stronger than thermoplastic materials due to this 3-D network
of bonds, and are also better suited to high-temperature applications up to the decomposition
temperature of the material. They do not lend themselves to recycling like thermoplastics
Bakelite, a Phenol Formaldehyde Resin (used in electrical insulators and plastic wear)
Urea-formaldehyde foam (used in plywood, particleboard and medium-density fibreboard)
Melamine (used on worktop surfaces)
Polyester Resin (used in glass-reinforced plastics/fibreglass (GRP))
Epoxy Resin (used as an adhesive and in fibre reinforced plastics such as glass reinforced plastic
and graphite-reinforced plastic)
A thermoplastic is a material that is plastic or deformable, melts to a liquid when heated and
freezes to a brittle, glassy state when cooled sufficiently. Most thermoplastics are high molecular
weight polymers whose chains associate through weak van der Waals forces (polyethylene);
stronger dipole-dipole interactions and hydrogen bonding (nylon); or even stacking of aromatic
rings (polystyrene). Thermoplastic polymers differ from thermosetting polymers (Bakelite;
vulcanized rubber) which once formed and cured, can never be remelted and remolded. Many
thermoplastic materials are addition polymers; e.g., vinyl chain-growth polymers such as
polyethylene and polypropylene.
Thermoplastics are elastic and flexible above a glass transition temperature Tg, specific for each
one the midpoint of a temperature range in contrast to the sharp freezing point of a pure
crystalline substance like water. Below a second, higher melting temperature, Tm, also the
midpoint of a range, most thermoplastics have crystalline regions alternating with amorphous
regions in which the chains approximate random coils. The amorphous regions contribute
elasticity and the crystalline regions contribute strength and rigidity, as is also the case for nonthermoplastic fibrous proteins such as silk. (Elasticity does not mean they are particularly
stretchy; e.g., nylon rope and fishing line.) Above Tm all crystalline structure disappears and the
chains become randomly interdispersed. As the temperature increases above Tm, viscosity
gradually decreases without any distinct phase change.
122
Thermoplastics can go through melting/freezing cycles repeatedly and the fact that they can be
reshaped upon reheating gives them their name. Animal horn, made of the protein -keratin,
softens on heating, is somewhat reshapable, and may be regarded as a natural, quasithermoplastic material.
Thermoplastics are useful between Tg and Tm, a temperature range in which most are neither
brittle nor liquid. If a plastic with otherwise desirable properties has too high a Tg, it can often be
lowered by adding a low-molecular-weight plasticizer to the melt before forming (Plastics
extrusion; molding) and cooling. A similar result can sometimes be achieved by adding nonreactive side chains to the monomers before polymerization. Both methods make the polymer
chains stand off a bit from one another. Before the introduction of plasticizers, plastic automobile
parts often cracked in cold winter weather. Another method of lowering Tg (or raising Tm) is to
incorporate the original plastic into a copolymer, as with graft copolymers of polystyrene, or into
a composite material.
Although modestly vulcanized natural and synthetic rubbers are stretchy, they are elastomeric
thermosets, not thermoplastics. Each has its own Tg, and will crack and shatter when cold
enough so that the cross linked polymer chains can no longer move relative to one another. But
they have no Tm and will decompose at high temperatures rather than melt. Recently,
thermoplastic elastomers have become available.
Common plastics and their typical uses
Polyethylene (PE)
wide range of uses, very inexpensive
Polypropylene (PP)
food containers, appliances
Polystyrene (PS)
packaging foam, food containers, disposable cups, plates and cutlery
Polyethylene terephthalate (PETE)
beverage containers
Polyamide (PA) (Nylon)
fibers, toothbrush bristles, fishing line
123
Polyester (PES)
fibres, textiles
Polyvinyl chloride (PVC)
plumbing pipes, flooring, shower curtains, erotic clothing
Polycarbonate (PC)
compact discs, eyeglasses
Acrylonitrile butadiene styrene (ABS)
electronic equipment cases (e.g., computer monitors, printers, keyboards)
Polyvinylidene chloride (PVDC) (Saran)
food packaging
Polytetrafluoroethylene (PTFE) (Teflon)
heat resistant, low-friction coatings, used in things like frying pans and water slides
Plastarch Material
biodegradable and heat resistant, thermoplastic composed of modified corn starch.
Polyurethane
insulation foam, upholstery foam
Bakelite
insulating parts in electrical fixtures (it is a thermosetting plastic, a.k.a. phenol
formaldehyde or phenolic resin, that can be moulded by heat and pressure when mixed
with a filler-like wood flour or can be cast in its unfilled liquid form.)
Polylactic acid
a biodegradable, thermoplastic, aliphatic polyester derived from lactic acid which in turn
can be made by fermentation of various agricultural products such as corn starch.
Mechanical behavior of polymers
The description of stress-strain behavior is similar to that of metals, but a very important
consideration for polymers is that the mechanical properties depend on the strain rate,
temperature, and environmental conditions. The stress-strain behavior can be brittle, plastic and
highly elastic (elastomeric or rubberlike). Tensile modulus (modulus) and tensile strengths are
orders of magnitude smaller than those of metals, but elongation can be up to 1000 % in some
cases. The tensile strength is defined at the fracture point and can be lower than the yield
124
strength. Mechanical properties change dramatically with temperature, going from glass-like
brittle behavior at low temperatures (like in the liquid-nitrogen demonstration) to a rubber-like
behavior at high temperatures .In general, decreasing the strain rate has the same influence on the
strain-strength characteristics as increasing the temperature: the material becomes softer and
more ductile.
Deformation of Polymers
Many semicrystalline polymers have the spherulitic structure and deform in the following steps :
The macroscopic deformation involves an upper and lower yield point and necking. Unlike the
case of metals, the neck gets stronger since the deformation aligns the chains so increasing the
tensile stress leads to the growth of the neck.
Factors that Influence the Mechanical Properties of Polymers
The tensile modulus decreases with increasing temperature or diminishing strain rate. Obstacles
to the steps mentioned in strengthen the polymer. Examples are cross-linking (aligned chains
have more van der Waals inter-chain bonds) and a large mass (longer molecules have more interchain bonds). Crystallinity increases strength as the secondary bonding is enhanced when the
molecular chains are closely packed and parallel. Predeformation by drawing, analogous to strain
hardening in metals, increases strength by orienting the molecular chains. For undrawn
polymers, heating increases the tensile modulus and yield strength, and reduces the ductility opposite of what happens in metals.
Crystallization, Melting, and Glass Transition Phenomena
Crystallization rates are governed by the same type of S-curves we saw in the case of metals
Nucleation becomes slower at higher temperatures. The melting behavior of semicrystalline
polymers is intermediate between that of crystalline materials (sharp density change at a melting
125
temperature) and that of a pure amorphous material (slight change in slope of density at the
glass-transition temperature).
The glass transition temperature is between 0.5 and 0.8 of the melting temperature. The melting
temperature increases with the rate of heating, thickness of the lamellae, and depends on the
temperature at which the polymer was crystallized. Melting involves breaking of the inter-chain
bonds, so the glass and melting temperatures depend on:
size of molecule
cross-linking
Processing of Plastics
Injection moulding (United States Injection Molding) is a manufacturing technique for making
parts from thermoplastic material. Molten plastic is injected at high pressure into a mold, which
is the inverse of the desired shape. The mold is made by a moldmaker (or toolmaker) from metal,
usually either steel or aluminium, and precision-machined to form the features of the desired
part. Injection moulding is very widely used for manufacturing a variety of parts, from the
smallest component to entire body panels of cars. It is the most common method of production,
with some commonly made items including bottle caps and outdoor furniture. The most
commonly used thermoplastic materials are polystyrene (low-cost, lacking the strength and
longevity of other materials), ABS or acrylonitrile butadiene styrene (a co-polymer or mixture of
compounds used for everything from Lego parts to electronics housings), nylon (chemically
resistant, heat-resistant, tough and flexible - used for combs), polypropylene (tough and flexible used for containers), polyethylene, and polyvinyl chloride or PVC (more common in extrusions
as used for pipes, window frames, or as the insulation on wiring where it is rendered flexible by
the inclusion of a high proportion of plasticiser).
Compression molding is a method of molding in which the molding material, generally
preheated, is first placed in an open, heated mold cavity. The mold is closed with a top force or
126
plug member, pressure is applied to force the material into contact with all mold areas, and heat
and pressure are maintained until the molding material has cured. The process employs
thermosetting resins in a partially cured stage, either in the form of granules, putty-like masses,
or preforms. Compression molding is a high-volume, high-pressure method suitable for molding
complex, high-strength fiberglass reinforcements. Advanced composite thermoplastics can also
be compression molded with unidirectional tapes, woven fabrics, randomly orientated fiber mat
or chopped strand. The advantage of compression molding is its ability to mold large, fairly
intricate parts. Compression molding produces fewer knit lines and less fiber-length degradation
than injection molding.
Extrusion moulding is a manufacturing process used to make pipes, hoses, drinking straws,
curtain tracks, rods, and fibres.The machine used to extrude materials is very similar to an
injection moulding machine. A motor turns a screw which feeds granules of plastic through a
heater. The granules melt into a liquid which is forced through a die, forming a long 'tube like'
shape. The shape of the die determines the shape of the tube. The extrusion is then cooled and
forms a solid shape. The tube may be printed upon, and cut at equal intervals. The pieces may be
rolled for storage or packed together. Shapes that can result from extrusion include T-sections,
U-sections, square sections, I-sections, L-sections and circular sections. One of the most famous
products of extrusion moulding is the fiber optic.
Blow molding or blow moulding is a manufacturing process by which hollow plastic parts are
formed. In general, there are three main types of blow molding; Extrusion Blow Molding,
Injection Blow Molding, and Stretch Blow Molding.
Extrusion blow molding In Extrusion Blow Molding (EBM), plastic is melted and extruded into
a hollow tube (a parison). This parison is then captured by closing it into a cooled metal mold.
Air is then blown into the parison, inflating it into the shape of the hollow bottle, container or
part. After the plastic has cooled sufficiently, the mold is opened and the part is ejected.
Injection blow molding The process of Injection Blow Molding (IBM) is used for the production
of hollow glass and plastic objects in large quantities. In the IBM process, the polymer is
injection molded onto a core pin; then the core pin is rotated to a blow molding station to be
inflated and cooled. This is the least-used of the three blow molding processes, and is typically
127
used to make small medical and single serve bottles. The process is divided into three steps:
injection, blowing and ejection.
The injection blow molding machine is based on an extruder barrel and screw assembly which
melts the polymer. The molten polymer is fed into a manifold where it is injected through
nozzles into a hollow, heated preform mould. The preform mold forms the external shape and is
clamped around a mandrel (the core rod) which forms the internal shape of the preform. The
preform consists of a fully formed bottle/jar neck with a thick tube of polymer attached, which
will form the body.
The preform mold opens and the core rod is rotated and clamped into the hollow, chilled blow
mold. The core rod opens and allows compressed air into the preform, which inflates it to the
finished article shape.
After a cooling period the blow mold opens and the core rod is rotated to the ejection position.
The finished article is stripped off the core rod and leak-tested prior to packing. The preform and
blow mold can have many cavities, typically three to sixteen depending on the article size and
the required output. There are three sets of core rods, which allow concurrent preform injection,
blow molding and ejection.
Another application of injection blow molding is in the production of soft elastic gelatin capsules
for pharmaceutical applications. Two strips of gelatin are pressed together in a rotary die which
cuts out the desired shape of capsule while the fill liquid is injected. Afterwards, they are cooled
and dried to yield a firm, strong capsule.
Stretch blow molding In the Stretch Blow Molding (SBM) process, the plastic is first molded
into a "preform" using the Injection Molded Process. These preforms are produced with the
necks of the bottles, including threads (the "finish") on one end. These preforms are packaged,
and fed later (after cooling) into an EBM blow molding machine. In the SBM process, the
preforms are heated (typically using infrared heaters) above their glass transition temperature,
then blown using high pressure air into bottles using metal blow molds. Usually the preform is
stretched with a core rod as part of the process. The stretching of some polymers, such as PET
128
(Polyethylene Terephthalate) results in strain hardening of the resin, allowing the bottles to resist
deforming under the pressures formed by carbonated beverages, which typically approach 60 psi.
The main applications are bottles, jars and other containers. The Injection blow molding process
produces bottles of superior visual and dimensional quality compared to extrusion blow molding.
The process is ideal for both narrow and wide-mouthed containers and produces them fully
finished with no flash. A sign of injection blow molding is the seam where the two halves of the
mold meet.
This picture shows what happens inside the blow mold. The preform is first stretched
mechanically with a stretch rod. As the rod travels down low-pressure air of 5 to 25 bar (70 to
350 psi) is introduced blowing a 'bubble'. Once the stretch rod is fully extended, high-pressure air
of up to 40 bar (580 psi) blows the expanded bubble into the shape of the blow mold.
COMPOSITES
Particle-reinforced composites
These are the cheapest and most widely used. They fall in two categories depending onthe size of
the particles:
large-particle composites, which act by restraining the movement of the matrix, if well
bonded.
Large-Particle Composites
Properties are a combination of those of the components. The rule of mixtures predicts that an
upper limit of the elastic modulus of the composite is given in terms of the elastic moduli of the
matrix (Em) and the particulate (Ep) phases by:
129
Ec = EmVm + EpVp
where Vm and Vp are the volume fraction of the two phases. A lower bound is given by:
Ec = EmEp / (EpVm + EmVp)
Concrete
The most common large-particle composite is concrete, made of a cement matrix that bonds
particles of different size (gravel and sand.) Cement was already known to the Egyptians and the
Greek. Romans made cement by mixing lime (CaO) with volcanic ice. In its general from,
cement is a fine mixture of lime, alumina, silica, and water. Portland cement is a fine powder of
chalk, clay and lime-bearing minerals fired to 1500o C (calcinated). It forms a paste when
dissolved in water. It sets into a solid in minutes and hardens slowly (takes 4 months for full
strength). Properties depend on how well it is mixed, and the amount of water: too little incomplete bonding, too much excessive porosity.
The advantage of cement is that it can be poured in place, it hardens at room temperature and
even under water, and it is very cheap. The disadvantages are that it is weak and brittle, and that
water in the pores can produce crack when it freezes in cold weather. Concrete is cement
strengthened by adding particulates. The use of different size (stone and sand) allows better
packing factor than when using particles of similar size.
Concrete is improved by making the pores smaller (using finer powder, adding polymeric
lubricants, and applying pressure during hardening. Reinforced concrete is obtained by adding
steel rods, wires, mesh. Steel has the advantage of a similar thermal expansion coefficient, so
there is reduced danger of cracking due to thermal stresses. Pre-stressed concrete is obtained by
applying tensile stress to the steel rods while the cement is setting and hardening. When the
tensile stress is removed, the concrete is left under compressive stress, enabling it to sustain
tensile loads without fracturing. Pre-stressed concrete shapes are usually prefabricated. A
common use is in railroad or highway bridges.
130
Cermets are composites of ceramic particles (strong, brittle) in a metal matrix (soft, ductile) that
enhances toughness. For instance, tungsten carbide or titanium carbide ceramics in Co or Ni.
They are used for cutting tools for hardened steels.
Reinforced rubber is obtained by strengthening with 20-50 nm carbon-black particles. Used in
auto tires.
Dispersion-Strengthened Composites
Use of very hard, small particles to strengthen metals and metal alloys. The effect is like
precipitation hardening but not so strong. Particles like oxides do not react so the strengthening
action is retained at high temperatures.
Fiber-reinforced composites
In many applications, like in aircraft parts, there is a need for high strength per unit weight
(specific strength). This can be achieved by composites consisting of a lowdensity (and soft)
matrix reinforced with stiff fibers.
The strength depends on the fiber length and its orientation with respect to the stress direction.
The efficiency of load transfer between matrix and fiber depends on the interfacial bond.
Structural Composites
Largest and most diverse use of composites due to ease of fabrication, low cost and good
properties.
Glass-fiber reinforced composites (GFRC) are strong, corrosion resistant and lightweight, but not
very stiff and cannot be used at high temperatures. Applications include auto and boat bodies,
aircraft components.
Carbon-fiber reinforced composites (CFRC) use carbon fibers, which have the highest specific
module (module divided by weight). CFRC are strong, inert, allow high temperature use.
Applications include fishing rods, golf clubs, aircraft components. Kevlar, and aremid-fiber
composite can be used as textile fibers. Applications include bullet-proof vests, tires, brake and
clutch linings.
Wood
131
This is one of the oldest and the most widely used structural material. It is a composite of strong
and flexible cellulose fibers (linear polymer) surrounded and held together by a matrix of lignin
and other polymers. The properties are anisotropic and vary widely among types of wood. Wood
is ten times stronger in the axial direction than in the radial or tangential directions.
Smart materials
Smart materials are designed materials that have one or more properties that can be significantly
changed in a controlled fashion by external stimuli, such as stress, temperature, moisture, pH,
electric or magnetic fields.
Group of new and state-of-the-art materials now being developed, and expected to have
significant influence on present-day technologies, especially in the fields of medicine,
manufacturing and defense. Smart/Intelligent material system consists some type of sensor
(detects an input) and an actuator (performs responsive and adaptive function).
Actuators may be called upon to change shape, position, natural frequency, mechanical
characteristics in response to changes in temperature, electric/magnetic fields, moisture, pH, etc.
Four types of materials used as actuators: Shape memory alloys, Piezo-electric ceramics,
Magnetostrictive materials, Electro-/Magneto-rheological fluids. Materials / Devices used as
sensors: Optical fibers, Piezo-electric materials, Micro-electro-mechanical systems (MEMS), etc.
Typical applications: By incorporating sensors, actuators and chip processors into system,
researchers are able to stimulate biological human-like behavior; Fibers for bridges, buildings,
and wood utility poles; They also help in fast moving and accurate robot parts, high speed
helicopter rotor blades; Actuators that control chatter in precision machine tools; Small
microelectronic circuits in machines ranging from computers to photolithography prints; Health
monitoring detecting the success or failure of a product.
Nano-materials
132
FRACTURE
Fundamentals of Fracture
Fracture is a form of failure where the material separates in pieces due to stress, at temperatures
below the melting point. The fracture is termed ductile or brittle depending on whether the
elongation is large or small. Steps in fracture (response to stress):
Crack
formation
Crack
propagation
Ductile Fracture
Stages of ductile fracture
Initial necking
Small cavity formation (micro voids)
Void growth (ellipsoid) by coalescence into a crack
133
134
Impact Fracture:
Impact fractures can best be described as a flute or strip of material that was cleanly sheared
from a projectile point. The most common type of impact fracture starts at the tip of a point and
runs down one blade edge possibly reaching the shoulder of a point. Some points were reworked
into a useable point after having been damaged by an impact fracture. Normalized tests, like the
Charpoy and Izod tests measure the impact energy required to fracture a notched specimen with
a hammer mounted on a pendulum. The energy is measured by the change in potential energy
(height) of the pendulum. This energy is called notch toughness.
FATIGUE
Fatigue is the catastrophic failure due to dynamic (fluctuating) stresses. It can happen in bridges,
airplanes, machine components, etc. The characteristics are: long period of cyclic strain
the most usual (90%) of metallic failures (happens also in ceramics and polymers)
Cyclic Stresses
These are characterized by maximum, minimum and mean stress, the stress amplitude, and the
stress ratio.
Crack Initiation and Propagation
Stages is fatigue failure:
I. crack initiation at high stress points (stress raisers)
II. propagation (incremental in each cycle)
III. final failure by fracture
Stage I - propagation
slow
Stage II - propagation
Crack propagates by repetitive plastic blunting and sharpening of the crack tip.
Corrosion of Metals
The corrosion resistance of metals and alloys is a basic property related to the easiness with
which these materials react with a given environment. Corrosion is a natural process that seeks to
reduce the binding energy in metals. The end result of corrosion involves a metal atom being
oxidized, whereby it loses one or more electrons and leaves the bulk metal. The lost electrons are
conducted through the bulk metal to another site where they are reduced. In corrosion parlance,
the site where metal atoms lose electrons is called the anode, and the site where electrons are
transferred to the reducing species is called the cathode.
Pure metals are used in many applications. Copper, for example, is used to make the wire which
goes inside electrical cables. Copper was chosen because it can be drawn into long thin wires
very easily (it is ductile) and because it is a good conductor of electricity. Pure aluminum can
also be used in wiring. It is also used as a cladding material for aluminum alloy substrates.
Currently there are 86 known metals. Before the 19th century only 24 of these metals had been
discovered and, of these 24 metals, 12 were discovered in the 18th century. Therefore, from the
discovery of the first metals, gold and copper, until the end of the 17th century, some 7700 years,
only 12 metals were known. Four of these metals, arsenic, antimony , zinc and bismuth , were
discovered in the thirteenth and fourteenth centuries, while platinum was discovered in the 16th
century. The other seven metals, known as the Metals of Antiquity, were the metals upon which
civilization was based. These seven metals are Gold, Copper, Silver, Lead, Tin, Iron,Mercury.
Corrosion of Ceramics:
It is often said that one of the biggest advantages which ceramics have over other materials is
their corrosion resistance, that is, their chemical inertness in corrosive environments. Is this
always true?
Corrosion is generally understood as property degradation due to environmental attack. As it will
be shown in this section, there are a number of environments in which ceramics can degrade at a
rapid rate. There exists a tremendous need for reliable and corrosion resistant structural ceramic
or partly ceramic materials which can be used in aggressive environments such as:
high energy battery systems (such as sodium-sulphur): beta-alumina is being investigated
gas turbines: silicon nitride and/or carbide are being investigated
heat exchangers: SiC, composites are being investigated
137
Ceramics are indeed much more environmentally stable, as compared to any other group of
engineering materials, e.g. metals or plastics. Still, the potential for ceramics as corrosion
resistant engineering structural materials are far from being fully realized, because of:
mechanical nonreliability of structural ceramic components
difficult design with brittle materials
a shortage of information and standardization of ceramics
human reluctance to use non-ductile materials
Issues of particular importance when considering corrosion of ceramics:
The resistance of many ceramics to wetting by a corrosive liquid is a valuable property.
Little corrosion is expected if a liquid does not wet a ceramic. This is why, for example,
born nitride (BN) and graphite are useful in handling melts and including the extremely
corrosive melts of silicate glasses. BN and graphite are not wetted by these liquids.
The solubility of the reaction product in the corrosive environment (liquid) is critical to
the extent of corrosion. Reaction barriers can form and prevent corrosion. Some examples
are silica on silicon carbide or nitride, and alumina on Al. On the other hand, continuous
dissolution of the reaction product can occur and sustain corrosion even for small
chemical driving force, for instance Al2O3 in molten KOH.
Even if a major component of the ceramic is resistant to a given corrosive environment, a
minor phase (especially a grain boundary phase, in particular under stress) could be
corroded (leached), leading to the general failure of the component. Some examples
include:
Alumina in water, where preferential attack of the grain boundary glassy (silicate)
phases occurs.
The preferential attack of free Si in reaction bonded SiC, by alkalis or molten
metals.
The oxide grain boundary phases in nonoxides (B2O3 in BN, silicates in Si3N4
and SiC) are sensitive to water.
Severe corrosion takes place if the ceramic is in contact with a substance which can combine
with it and form low-melting liquids (i.e. with eutectic point below ambient temperature).
138
The example of above situation is the system composed of metallurgical slag in contact with
refractories. If the reaction is thermodynamically possible, the corrosion will proceed at a
dramatic rate if the refractory is wetted by the slag.
139