Escolar Documentos
Profissional Documentos
Cultura Documentos
SL NO
TITLE
INTENT
TECHNICAL SPECIFICATION.
BILL OF QUANTITY
SUPPLIER DOCUMENTATION
10
11
DEVIATION
ANNEXURES
Annexure-01:-Typical Cable Tray Details
2|9
O12247-0GS-E-G-21026-001
1.0
INTENT
Jindal Steel & Power Limited is setting up a SINTER PLANT 490.5 Sqmm at Angul, Odisha. Cable Tray required
for the same.
Intent of this Technical Procurement Document (TPD) is to fabrication, manufacture and supply of Ca-
ble Tray as per details specified herein (but not limited to the items specifically mentioned) for satisfactory performance of the equipment / system.
If the Bidder finds inconsistencies in any part of this TPD and/or its enclosures, the same has to be communicated in writing with proper clarification/justification and alternative proposals to resolve the inconsistencies
have to be furnished before placement of order.
2.0
Hot Dip Galvanized Sheet Steel Prefabricated Ladder Type Cable Tray.
ii)
Hot Dip Galvanized Sheet Steel Prefabricated Perforated Type Cable Tray.
3.0
3|9
O12247-0GS-E-G-21026-001
4.0
Description:
General Specification EI & A (Page 24 to 26 of 38 , Cl No. 1.28)
In case of inconsistencies are observed between this TPD and general technical specification referred herein,
the information contained in this TPD has priority at all times. In any case, it is essential that all such inconsistencies are to be clarified in writing before finalization of order. Make of all equipments shall be as per Approved make list of JSPL
5.0
TECHNICAL SPECIFICATION
For laying of cables in all outdoor / indoor areas, Hot Dip Galvanized sheet steel Ladder Type Cable Trays
shall be used. It shall be pre-fabricated from 2 mm thick mild steel sheet at factory only, 2.5 Mtr. long per
piece with its fittings / accessories shall be manufactured as per Drawings enclosed here with. These trays
shall be hot dip galvanized after fabrication. The galvanization shall be according to IS-2629 / as mentioned in data sheet-A. The galvanization shall be uniform, clean, smooth continuous and free from acid
spots. If the galvanization of the samples is found defective, the entire batch of sheet will have to be regalvanized at bidders cost. All nuts, bolts, washers etc. shall be cadmium plated or zinc plated.
The ladder type cable trays shall be in piece lengths as per data sheetA. Tray ends shall be connected to
either straight tray or horizontal elbow, vertical elbows, Tee, Cross, reducer etc. by using coupler plates.
All welded joints shall be smooth enough to provide a good appearance and shall not cause any injury to
working personnel or any damage to the cables laid on it. All welding work shall be done by skilled personnel.
Suitable side coupler plates shall be provided with necessary hardware (i.e. bolts, nuts, washers etc.) for
the two sides of each of the above types of cable trays, elbow, cross Tees etc, as applicable.
Cable racks shall be hot-dip galvanized after fabrication. Minimum value of average mass of zinc coating shall
be 610 gm/m2 as per IS: 4759.
Pre-fabricated perforated trays, generally of 2.5 meters length made hot-dip of galvanized 2 mm thick sheet
steel shall be used for laying control cables. The trays shall have vertical edge of height not less than 100
mm on both sides. The control cables shall be clamped by means of suitable PVC straps both for horizontal
and vertical run of cables, at each bend and turnings from horizontal to vertical direction and vice-versa.
The clamps shall be placed at an interval of 1500mm apart in horizontal run and 1000mm in vertical run.
Minimum value or average mass of zinc coating shall be 460 gm/m2 as per IS: 4759.
4|9
O12247-0GS-E-G-21026-001
Item
Type
Size
Qty (mtr.)
Cable Tray
Ladder Type
600 mm Width
16300
Cable Tray
Ladder Type
300 mm width
3400
Cable Tray
Perforated Type
300 mm Width
13400
Item Description
Quantity in no.
1.
As Reqd.
2.
As Reqd.
As Reqd.
2.
As Reqd.
1.
As Reqd.
2.
As Reqd.
As Reqd.
Note:
1. Quantities indicated in the above BOQ are tentative and may undergo change during further detail engineering. Bidder may furnish their offer with unit rate basis.
2. The above Cable Trays shall be used for HV ( 33KV, 6.6kV) & MV (415 V / 240V / 110 V) Cables.
3. All the coupler plates shall be complete with required holes and its associated nuts, bolts, washers etc.
5|9
O12247-0GS-E-G-21026-001
ii)
ii.
iii.
iv.
v.
vi.
All drawings, documents and technical data are to be furnished in Metric/ SI units and English language only.
All Drawings will be submitted in 10 Sets. All drawings will be submitted in folders. No
looses/stapled sheets will be provided.
At least two sets of clearly legible site corrected drawings will be submitted after commissioning.
As Built drawings will be first copy/clear photocopy and will be properly arranged in suitable
folders. The folders will have a list of all the drawings it contains on the front inside cover. List
of all assemblies, sub assemblies, electronic cards, etc will be provided in a separate folder
along with the OEMs ordering code.
The scope of successful supplier will also cover preparation of and submission of AS COMMISSIONED / AS BUILT drawing and documents in 10 prints and 2 sets of soft copies along with
any other relevant drawings / documents as per the project / client / consultants requirement.
6|9
O12247-0GS-E-G-21026-001
8.0
9.0
10.0
11.0
DEVIATION
The bidder shall furnish the list of deviation stating the reasons for deviation with supporting documents as
per Deviation List Format. Otherwise, the bidder shall confirm No Deviation in the offer.
In absence of a deviation list, it would be considered that the bidder has no deviations from the TPD and the
entire technical specification is acceptable to the bidder.
7|9
O12247-0GS-E-G-21026-001
No deviations from the TPD shall be entertained after order placement. If the bidder has a genuine technical
reason for any deviation after order placement, prior approval for the same should be taken from the purchaser with proper supporting documents.
Deviation List Format
Sl. No
8|9
Details
Clause
Page
O12247-0GS-E-G-21026-001
GS Elbows / Tees
Shall be prefabricated.
2 mm
Cable tray
IS: 4759
Reference Standard
610 gm/mm2
460 gm/mm2
Notes:
For GS ladder type cable trays, all rungs & coupler plate should be slotted, details of the same will be
intimated to successful bidder.
The dimensions of all Elbows, Tees, and Cross etc. shall be as per JSPL requirement and details of the
same will be intimated to successful bidder.
Welding shall be done as per IS specifications. The Width and Length of trays & accessories shall be
within a tolerance of 3mm.
9|9
O12247-0GS-E-G-21026-001