Escolar Documentos
Profissional Documentos
Cultura Documentos
The home or any other area can be made fully secured using this device.
The Infrared sensor or microphone will activate the mobile or landline to
redial your saved number and intimate. you instantly. Apart from this, you may
control the DOOR remotely.
TELE-VOTING MACHINE
The remote voting can be done with Mobile phone. The mobile/landline
phone can be placed at transmitting and receiving end. One can listen the voice
message and can vote by pressing keypad buttons. his vote to the selected
candidate out of four.
TELE-REMOTE SWITCHING
The set of four electrical devices can be controlled remotely by using mobile/landline
phone at the transmitting and receiving end. One can make a call and activate devices o
f its choice. It will give voice message to the operator to select the device.
The simple event counter with dual display and a minute timer can count the RF pulses of
HEART coming from distance and plot the graph on paper to read. The pulse rate of heart
will be taken from the Infrared IR finger sensor.
One can operate a file handling or electrical appliance control using a landline/mobile
phone to activate the connected hardware interfaced with PC parallel port.. (NOTE:
PC based projects required parallel port interfacing DB-25 connector port available.
The project will access the person identity using RFID unit and allow to enter the
plateform. It can maintain the database of user account for each entry/exit. (NOTE: PC
based projects required parallel port interfacing DB-25 connector port.
The project can be used as home automation device controller using TV remote (provided in
project) to control four electical devices. This can be extended for four more appliances
with additional circuit.
The project comprises a dc motor speed controller circuit with reed sensor. It is being
detected by this and display the same at LCD in form of speed Km./Hr. and also display the
distance covered by the vehicle.
The project will check the value of unknown capacitor at seven segment display.
Language :ASSEMBLY
It will check the pulse rate of the patient using IR sensors connected to Finger. Display
at seven segment LEDs.
This will check and display the distance between device and object/wall etc. at LCD. You
may call this as ULTRASONIC RADAR.
The project reads the motor speed on any ac/dc motor at four seven segment displays
using IR technique. The project also comprises a dc motor speed controller circuit to
change the speed of motor with a variable control. The output is connected to a LCD
display.
A Robotic car that follows the black line at the floor area based on Infra Red sensors
using transmitters and receivers.
The project will control four electrical devices from the remote end (another mobile) by
sending SMS to the GSM modem with a SIM card control unit. One can activate or de-activate
any of four devices.
This is a power switching circuit using SCR that controls the output signal by switching it
'on' or 'off', thereby controlling the power to the load.
The character display segments (Matrix)8X8x8 will show set of messages selected from four
keys in moving effect like Happy New year, Happy Birthday, Welcome to Electronics Dept.
Moving Display can be changed by simply pressing the key.
The project will show the names of person on LCD who has pressed the RFID key through
Encoder circuit. DATA decoder circuit will allows 16 persons to display their names on LCD
using microcontroller. Projcet included single RF tranmitter reciever circuit.
This intersting ROBOT will obey the signals from his Master and follows him always. It will
follow the footsteps of Master.
Assembled Price : 3500
4 APPLIANCES):One can operate (on/off) four electrical devices with TV remote syncronised
with circuit independently.
ELECTRONICS(EC,EN,EI,IC,EE)
SPEED CONTROL OF DC MOTOR
It controls the speed of DC motor by changing its flux with digital control circuit.
current.
Assembled Price : 4500
Project Level: Major
Project Size: 9*12 inches
The solar panel can be moved automatically with the direction of Sun to get maximum
energy from it further it shows five electrical concepts in one: (a) Generation of
electrical enegy from solar cell (b) Control of panel through DC gear motor.
The Fan speed will be automatically changed as per temperature i.e. if the temperature
rises, the fan will move fast and fan will run in low speed on low temperature.
Assembled Price : 2000
Project Level: Minor
Project Size: 9*12 inches
The power factor variations will be sensed by the sensing coil assembly and the digital
circuit will activate the relay driver unit to connect capacitors network to the direct
phase line.
Assembled Price : 4500
Unassembled Kit Price : 3000
Project Level: Major
Project Size: 9*12 inches
The four phases can be digitally controlled for a single phase load. The available phase-
out of the three from direct source and one from the inverter source will connect from the
load automatically if power trips at other.
A fan speed can be controlled by the multiple claps. Single clap to switch on, next clap
for 2nd speed, 3rd clap for third speed and fourth clap to switch off.
This simple op-amp based analog thermostat will stabilize temperatures to within a fraction
of one degree Centigrade.
This project will convert the sound energy to electrical by showing it at LED lights when a
harsh sound is created in front of it. An additional oscillator that generate different
medium of sound is also the part of this project to show variation in
The armatures of a 3 phase motor are connected as star at the time of power on and then
converted to delta when it reaches 3/4 of the full speed, in order to handle more power.
This solid state relay will operate the device without using mechanical relay.
This is the management of the rotational speed of an electric fan.The speed control is
performed by the fan based on the control signal. View
Assembled Price : 2500
Project Level: Minor
Project Size: 9*12 inches
The electrical DC to DC converter will be used in many application where low voltage DC to
PIEZOELECTRIC GENERATOR
The piezo crystals placed in an assembly will produce electricity when mechanical pressure
induced on it.
Assembled Price : 8000
Project Level: Major
Project Size: 9*12 inches
SOLAR INVERTER
WIND BELT
Another alternate energy generation to charge battery by low power wind, say simple fan
etc. A moving belt vibrate when wind strike it from any side.The magnets on both ends make
the generation of electrical energy .
An alternate source or energy can be generated by the modified dance floor using pressure
sensor based electricity generators.
This AIR GENERATOR generate electrical energy from the air stored in a storage chamber
using suitable air compressor.
Compressor less refrigerator to provide 12-15 degree temperature while cooling and is also
used to heat if required with the same Thermo-EMF peltier junction based system works on
12V battery to be charged with Solar Cells/ Panel.
HYBRID CHIMNEY
The dual natural energy sources say Wind and Sun energy is used to generate electrical
energy. A good alternate source of energy for areas like deserts or barren land, where sun
light is available but low speed of wind flow is there.
It works as we do cycling for exercise. Besides charging Mobile battery, it burns the extra
calories too.
The hand operated generator can be on the same principle.
This can be designed to generate electrical energy when vehicles cross the breaker and roll the
roller based
speed breakers connected with an alternator.
The different amusement rides can be designed to generate electrical enegy while children are
using actually
the park.
A Device SETUP that generate electrical energy from running water. The model comprises a
pump, a water
reservoir, an alternator to gen. electrical energy.
It actually track the sun as per its position and move the solar cell/water heating plates
accordingly so as to get
maximum power from sun light.
WIND MILL
The Actual wind mill model that produce electrical energy from wind and charge the battery to
run inverter directly.
This remotely operated device controller will work with mobile blue tooth network.
This project will transmit high voltage high frequency electrical energy from source to
destination without using
any electrical wires etc.
Its a electronic device which has transformer and other control circuit for controlling output ac
voltage. it controls
automatically the output voltage to a certain voltage.
This circuit consists of relaxation oscillator, pulse count were frequency circuit, SCR control
socket circuits, voice
circuits and exchange music buck rectifier circuit.
THERMO-EMF REFRIGERATOR
The WOODEN box is being modified as simple compressor less refrigerator to provide 12-15
degree temperature
while cooling and is also used to heat if required with the same Thermo-EMF peltier junction
based system. View More
This circuit operates very fast with no intentional time delay and the operating time of these relay
can be as low as 0.01sec .
A Multiple or single device control circuit can be operated with this circuit.
Four electrical device can be remotely operated by this system. A transmitter with encoder circuit
will transmit
the IR frequency 38kHz and a matching receiver will receive the signal to switch the relays to
control devices.
A single device can be remotely operated by this system. A transmitter will transmit the IR
frequency 38kHz and
a matching receiver will receive the signal to switch a relay to control device.
The remote operation to control speed of fan or motor using single RF signal circuit with gear
motor driver.
Can be used as remote lamp dimmer.
The data transmission using RF 433 Mhz module will enable to operated four electrical device
switching or
single fan speed control.
An electrical device will be remotely operated for specific time using simple timer circuit.
A visual indication assures the uses in which time mode the circuit is operating out of 10 stages.
A microphone amplifier with flip flop circuit causes to change the motor direction.
Assembled Price : 1200
Project Level: Minor
Project Size: 9*12 inches
The circuit will switch on the different connected loads one by one as instant start will dimming
the lights due
to heavy starting current with an additional timer connected to it.
Assembled Price : 5500
Project Level: Major
Project Size: 9*12 inches
The circuit will cut off automatically if the dual phase gadget will not getting two phases, thus to
prevent the
gadget.
A logic IC based circuit control the top and lower level of water tank.
It controls the speed of INDUCTION motor by using PWM technique with THERISTOR as
power driver control.
It controls the speed of DC motor by changing PWM using TRANSISTOR as power driver
control.
THERMO SWITCH
The dual mode can be set in both Light and Temperature controls i.e. light operated, dark
operated, high temperature
operated, and low temperature operated modes on single setup.
It sense and detect the preset temperature of the unit and an RF link connected to it will indicate
us using wireless circuit
to switch of the control system if required.
The motorised ventilators in room will automatically be open when it sense high temperature.
This fast and low power consumption semiconductors circuit equipped with new technology
based on Mosfets specially
desiged for inverters.
Assembled Price : 3200
Project Level: Major
Project Size: 9*12 inches
This circuit is helpful for electronic gadgets, which draw small current but are operated on
comparatively high voltage.
The circuit control the speed of fan at two ranges which in turn controlled by room temperature.
It control water pump when overhead tank is filled and gives alarm indication. It also checks
under ground water level to
protect dry run for pump.
It counts the number of persons entered in a hall and accordingly control the electrical device.
Thus it is helpful for
energy saving in room.
An electronic starter to 'ON' and 'OFF' the connected motor of single phase through relay.
It automatically close an unmanned railway gate when train is coming from one side and close it
automatically when it
passes through it.
This eight digit fan regulator display the speed at FND display and is more reliable than
conventional rotary regulator.
An inbuilt circuit for 20W tube light to glow in emergency. Required mini 6V bike battery.
100 watts inverter can be made using IGBT driver circuit for fast and energy efficient switching.
WIRELESS RF CODE LOCK FOR CAR/DOOR
Digital combination code lock to be opened remotely by RF transmitter and activate the door
relay and
motor to open the same.
A robotic vehicle that is controlled remotely by RF transmitter using RF 433 Mhz modules with
data encoder and
decoder ICs. It can go forward, reverse, left or right. An RF camera will capture the image and
transmit the same
at nearby TV to show live.
A robotic vehicle that is controlled remotely by RF transmitter using RF 433 Mhz modules with
data encoder and
decoder ICs. It can go forward, reverse, left or right. Detecting metal and inform to the operator
is an optional
attachment in this proje
This will not only check the temperature but also control the selected temperature to switch
on/off the unit.
This project will undertake the attendance using actual RFID card with reader interfaced with PC
serial port
The useful device for handicapped person to move the chair with the help of battery and motor
arrangement. The
keys will help to turn left or right side.
This embedded safety guard system with voice processor to play the prerecorded message in case
of any obstacle
The unit display the time in Hr. Min. and one can set the alarm also for a desired time at Seven
segment display.
The project will check the unknown frequency input upto 200KHz. coming from an IR source
and display at LCD.
Language :C
The three-stepper motor-based key controlled robotic arm can grip, lift and rotate the specified
object using 3-axis
movement.
The project performs the countdown operation for upto -99 minutes with two seven segments
display showing actual time
left to activate or de-activate the connected relay. It can be used as sports timer, kitchen timer or
conference timer.
The temperature of room can be diplayed at LCD using a sensitive device DS 1621.
It checks the pulse rate of patient from 10-15 meters away using RF link. Doctor can detect from
a comfortable distance
to connect the circuit with PC or any other devices, if required.
The compact car clock with seven segment display showing hours, minutes and seconds.
It is very close o the devices used by forensic lab to test if a person is lieying or not using the
change in body
resistance with state of mind. * changes in the digital reading will not be calibrated in project
demonstration. View More
Like wise the above it will check the PH value for acid and basis. * changes in the digital reading
will not be calibrated in
project demonstration.
It will read the CO2 level in an atmosphere using lime water as base. * changes in the digital
reading will not be calibrated
in project demonstration.
It check and plot the graph for pulse rate of heart on PC screen. The RF (radio frequency
signal)transmission of pulse
from patient is an added attraction..(NOTE: PC based projects required parallel port interfacing
DB-25 connector port.
This project will help the blind people to type at computer keyboard and the hardware assembly
will provide braille output
from parallel port.
It will give warning in audible form at no smoking zone. It may sense the smoke or even lighter
light and give audible
indication. Project incorporate voice chip on board(COB) module.
This intelligent walking stick for blind will be all together a helpful device for blind person as it
detect the obstacle in
front of it using IR sensor and it be give audio signal in form of pre-recorded voices of bus
number coming to bus stop.
This will check the alcohol level in human body duly checked with respirator through mouth
during car driving.
This will check the stress level of human being in different levels as skin sensing probes
connected to body. View More
This will detect pulse from fingers using blood pressure variation during heartbeat change. This
can be counted using
decade counter of 2 digit.