Escolar Documentos
Profissional Documentos
Cultura Documentos
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
1/50
DAFTAR ISI
I.
1.2
II
HARDWARE MAINTENANCE
2.1
LASER SHUTDOWN
2.1.1
Descriptions
2.2
2.3
III
2.1.2
Apparatus
2.1.3
2.1.4
FAN
2.2.1
Precautions
2.2.2
Task Flow
2.2.3
Apparatus
2.2.4
AIR FILTER
2.3.1
Task Flow
2.3.2
Apparatus
2.3.3
TRAFFIC MANAGEMENT
3.1 TIMING SOURCE SELECTION
Transmission Team
3.1.1
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
2/50
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
3/50
Transmission Team
I.
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
4/50
1.1.1.1 Precautions
Performing the configuration data restoration of the MSCB package will log off any session to
the target NE.
1) Press and hold the RESET button and COLD button on the MSCB package at the same time.
Keep pressing them. LEDs on the MSCB package go off.
2) Release the RESET button. (Keep pressing the COLD button.)
3) When the LED on the MSCB package lights up, release the COLD button.
4) Wait until all the LEDs on the MSCB package go off. (LEDs on the MSCB package stay on
while reading data.) However, if any alarm is detected within the NE, the LED(s)
corresponding to the detected alarm severity level will not go off.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
5/50
5) Click the Apply button on the dialog box. The confirmation box appears.
6) Click the Yes button on the confirmation box. A warning message box appears.
7) Confirm if this restoration is performed at the right time, then click the OK button.
The restoration process starts.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
6/50
8) When the process is completed, the following message appears to inform that your access is
now being logged off. Click the OK button to end the performance, and to log off.
1.1.2.1 Precautions
Performing the configuration data restoration of the MSCB package will log off any session to
the target NE.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
7/50
5) Click the Apply button on the dialog box. The confirmation box appears.
6) Click the Yes button on the confirmation box. A warning message box appears.
7) Confirm if this restoration is performed at the right time, then click the OK button.
The restoration process starts.
8) When the process is completed, the following message appears to inform that your access is
now being logged off. Click the OK button to end the performance, and to log off.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
8/50
1.1.3.1 Precautions
Performing the configuration data restoration of the MSCB package will log off any session to
the target NE.
5) Click the Apply button on the dialog box. The confirmation box appears.
6) Click the Yes button on the confirmation box. A warning message box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
9/50
7) Confirm if this restoration is performed at the right time, then click the OK button.
The restoration process starts.
8) When the process is completed, the following message appears to inform that your access is
now being logged off. Click the OK button to end the performance, and to log off.
System of WBM shelf will be backed up into the flash memory (SUB) in MSCB package.
NOTE: While in the backup process, you cannot make a session to the system via NMS or
another CID.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
10/50
3) Select Configuration Data Copy Backup from the menu. The confirmation message
appears.
4) Click the Yes button on the message box to proceed.
NOTE: Clicking the MEM Info button displays the Memory Information dialog box.
While in the process, the following indication box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
11/50
NOTE: Clicking the MEM Info button displays the Memory Information dialog box.
5) Click the Yes button on the confirmation box to proceed.
6) When completed, click the Close button on the Memory Copy dialog box.
This step is the end of the procedure.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
12/50
Transmission Team
II
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
13/50
HARDWARE MAINTENANCE
2.1.1 Descriptions
2.1.1.1 Automatic Laser Shutdown (ALS)
The Automatic Laser Shutdown (ALS) is enabled automatically if the incoming signal is lost for a
certain period of time. While in the ALS mode, where ALS Restart Mode is specified to AUTO, the
U-Node WBM will repeat transmitting signals periodically to check whether the traffic problem
occurred at the far-end NE is cleared. After receiving the normal signals from the far-end NE, ALS
mode is disabled and the local NE starts transmitting signals normally. The length of periodical signal
transmission interval can be customized. The ALS function can be disabled if not necessary.
2.1.2 Apparatus
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
14/50
5) Click in the Forced Shutdown field, and select ON from the pull-down menu.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
15/50
6) Click the Apply button on the Laser Shutdown dialog box(2). The forced shutdown is
executed. While in the process, the following indication box appears.
7) When completed, the indication box disappears. Click the Close button on the Laser
Shutdown dialog box(1).
8) Click the Close button on the Laser Shutdown dialog box(1).
NOTE: To disable the Forced Shutdown status, perform the procedure above, and select OFF in
step 5.
This step is the end of the procedure.
Transmission Team
5)
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
16/50
6) Click in the ALS Manual Release field, and select Short or Long for the output duration.
7) Click the Apply button on the Laser Shutdown dialog box(2). The manual laser release is
executed.
8) When completed, click the Close button on the Laser Shutdown dialog box(2).
9) Click the Close button on the Laser Shutdown dialog box(1).
If the laser shutdown status is not cleared, verify if an optical input is not lost, then repeat the
procedure.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
17/50
2.2 FAN
2.2.1 Precautions
If a fan fails, the fan should be replaced immediately in order to prevent the temperature within the
shelf from going up. Also, for the same reason, replacement should take no longer than 5 minutes.
Replace a fan
2.2.3 Apparatus
CAUTION!
Fan package provided for U-Node BBM (E32-145-M9992-0A01) cannot be mounted on
UNode WBM.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
18/50
1) Wear the wrist strap, and connect the other end to the ESD terminal on the WBM shelf.
2) Confirm that a new fan has been unpacked, and ready to be set.
The following Steps 3 thru 8 should not take no longer than 5 minutes.
Removing Fan:
3) Loosen a thumbscrew on the front of the fan to be replaced.
4) Pull the fan out by holding the grip on its front, and disengage the Fan package from the
backplane.
CAUTION: Do not grab the faceplate. A Fan package contains two fans;
one of these may still be rotating at high speed.
5) Wait for about 20 seconds, and confirm that the fan(s) are completely stopped.
6) Take the package off from the shelf.
7) Place the removed fan in the antistatic bag or container.
Installing a New Fan:
8) Confirm that a Fan package is appropriate type.
9) Pull the thumbscrew upward to flap the stopper open.
10) Install the new fan; push it further until the rear side is engaged to the shelf backplane.
11) Adjust the screw hole on the fan to the thumbscrew, and fasten it.
12) Verify that the FAIL lamp is not lit on the fan.
13) Disconnect the wrist strap.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
19/50
Replace a filter.
2.3.2 Apparatus
1) Wear the wrist strap, and connect the other end to the ESD terminal on the WBM shelf.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
20/50
3.1.1.1 Requirements
When the target timing reference has the following assignments, Timing Source Selection
operation is not available:
Operation Mode 1 (EXTCLK OUT1/2): FIX
PL: NSEL
Source Entry: NO ENT
The following operations are available for each reference assigned for Equipment, EXTOUT1, and
EXTOUT2:
3.1.1.2 Parameters
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
21/50
3. Select Timing Source Selection from the menu. The Timing Source
Selection dialog box appears.
5. Check the Switching Status of the target timing reference to see if it is operational.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
22/50
7. Click the Apply button to execute operation. While in the process, the following
indicator appears:
To make an immediate effect in the revertive mode, the duration specified for WTR (waittorestore)
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
23/50
can be omitted while in the WTR condition (after the WTR time count starts).
3. Select Timing Source Selection from the menu. The Timing Source Selection
dialog box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
24/50
6. Click the Apply button. While in the process, the following indicator appears:
Traffic maintenance should be carried out by an maintenance personnel to assure or inspect the quality
of the traffic.
The tasks provided in this section are not arranged in any specific order.
Loopback function allows fault isolation and pre-service operation practice. Performing loopback
interrupts the flow of traffic, and changes the normal transmission. Therefore, the use of loopbacks as
routine practice is not recommended.
When the loopback is executed, the system generates an AIS (alarm indication signal), and sends it to
the far-end NE. Also, all IPPM parameters will be indicated as INVALID.
Once the loopback is initiated, the MNT lamp (LED) on the package lights up to indicate that the
loopback is in operation. The loopback operation can be initiated STM1E package, E12/ E31/E32
package, and other optical facilities such as STM-16.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
25/50
The two different loopbacks cannot be executed to the same facility at a time.
Alarms in the path layer are masked during the loopback operation.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
26/50
5. Click the Apply button on the dialog box. The loopback is executed to the selected
facility. While in the process, the following message box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
27/50
5. Click the Apply button on the dialog box to release. While in the process, the
Following message box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
28/50
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
29/50
5. Click the Apply button on the dialog box. The loopback is executed to the selected
facility. While in the process, the following message box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
30/50
5. Click the Apply button on the dialog box to release. While in the process, the
following message box appears.
2.
Click Maintenance on the menu bar of the CID main window. The Maintenance
menu appears.
3.
4.
Confirm that the PDH Facility tab is selected. Then click in the Loopback
Operation field of the target facility, and select Remote Terminal Loopback.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
31/50
5. Click the Apply button on the dialog box. The loopback is executed
facility. While in the process, the following message box appears.
3. Select Loopback from the menu. The Loopback dialog box appears.
4. Confirm that the PDH Facility tab is selected. Then click in the Loopback Operation
field of the target facility, and select Release from the pull-down list.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
32/50
5. Click the Apply button on the dialog box to release. While in the process, the
following message box appears.
The following shows the switch groups and their applicable switching protection types:
LINES: Linear Protection
MS2FS: Ring Protection
MS4FS: Ring Protection, Span Protection
For the switch group of linear bidirectional, the same switching operation must be executed to the
LINES of the opposing node. If the opposing node runs non-NEC equipment, still the same type of
switching operation must be executed.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
33/50
Line switching protection has the Lockout mode for each switch group. In this mode, any
type of switch operation is disabled.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
34/50
Line switching protection has the Lockout mode for each switch group. In this mode, any
type of switch operation is disabled.
Line switching protection has the Lockout mode for each switch group. In this mode, any type of
switch operation is disabled.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
35/50
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
36/50
5. Click the button. The Protection Switching Line/BLSR dialog box for the
selected protection group appears.
6. Click in the Operation field to display the pull-down list, and select a switching
operation type:
7. Click the Apply button on the dialog box. The confirmation box appears.
8. Click the Yes button. The protection switch is executed.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
37/50
9. Click the Close button on the Protection Switching Line/BLSR dialog box
10. Click the Close button on the Protection Switching dialog box.
This step is the end of the procedure
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
38/50
5. Click the button. The Protection Switching Line/BLSR dialog box for the
selected protection group appears.
6. Click in the Operation field to display the pull-down list, and select Release (selected
operation
7. Click the Apply button on the dialog box. While in the process, the following
indication box appears.
8. Click the Close button on the Protection Switching Line/BLSR dialog box.
9. Click the Close button on the Protection Switching dialog box.
This step is the end of the procedure.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
39/50
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
40/50
5. Click the button. The Protection Switching Line/BLSR dialog box for the
selected protection group appears.
To release from the Lockout mode, remove a tick from the check box.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
41/50
9. Click the Close button on the Protection Switching Line/BLSR dialog box.
10. Click the Close button on the Protection Switching dialog box.
This step is the end of the procedure.
3. Select Exercise Protection Switching from the menu. The Exercise Protection
Switching dialog box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
42/50
NOTE: For the tab of ring protection switch group, either MS2FS or MS4SF is
displayed according to the configured ring protection.
5. Click (a) check box(es) to select (a) switch group(s). More than one groups can be
selected. To select all groups, click the Exercise All check box.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
43/50
Path protection selection has the Lockout mode for each facility. In this mode, any type of switch
(selection) operation is disabled.
3. Select Protection Switching Path from the menu. The Protection Switching
Path Selection dialog box appears.
For AU Facility:
(i) Click the Higher Order Path tab on the dialog box.
(ii) Select an AU facility in the list.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
44/50
(iii) Click the OK button. The Protection Switching Path dialog box appears.
For PDHTU/SDHTU Facility:
(i) Click the Lower Order Path tab on the dialog box.
(ii) Select a PDHTU or SDHTU facility in the list.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
45/50
(iii) Click the OK button. The Protection Switching Path dialog boxappears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
46/50
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
47/50
8. Click the Close button in the Protection Switching Path dialog box.
9. Click the Close button in the Protection Switching Path Selection dialog box.
This step is the end of the procedure.
3. Select Protection Switching Path from the menu. The Protection Switching
Path Selection dialog box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
48/50
For AU Facility:
(i) Click the Higher Order Path tab on the dialog box.
(ii) Select an AU facility in the list.
(iii) Click the OK button. The Protection Switching Path dialog box appears.
(i) Click the Lower Order Path tab on the dialog box.
(ii) Select a PDHTU or SDHTU facility in the list.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
49/50
(iii) Click the OK button. The Protection Switching Path dialog box appears.
Transmission Team
TRANSMISI BACKBONE
Versi
1.0
Tanggal
13/04/11
No. SOP/SMP
Transmission
Halaman
50/50
To release from the Lockout mode, remove a tick from the check box.
8. Click the Close button in the Protection Switching Path dialog box.
9. Click the Close button in the Protection Switching Path Selection dialog box.
This step is the end of the procedure.