Escolar Documentos
Profissional Documentos
Cultura Documentos
I.
OBJECTIVES
1. To analyze the parameters and characteristics of different types of voltage-divider
emitter (common-emitter) amplifier.
2. To decide which type is most suited for most applications.
II.
TEST EQUIPMENT
(1) Power Supply
(1) Dual Trace Oscilloscope
III.
PARTS NEEDED
(1) 100 BRN.BLK.BRN
(1) 1.5 k BRN.GRN.RED
(1)
(1)
(1)
(1)
IV.
(2) 10F
(1) 100F
Q1 (1) 2N3904
3.3 k ORG.ORG.RED
15 k BRN.GRN.ORG
10 k BRN.BLK.ORG
47 kYEL.VIO.ORG
PROCEDURE
1. Calculate the following for the circuit 0f Figure 1: IE, IC, VC, VCE, ZIN, ZO, Av, and
Vo. Set IE=Ic
+Vcc
+9v
Rc
3.3K?
R1
47K?
C2
10F
=100
C1
10F
RL
10K?
2 Vpp
2KHz
R2
15K?
RE2
1.5K?
f:
3. Measure the input and output impedance of the circuit of figure 1. Follow the
techniques described in the previous experiment.
4. Compare your computed values for Zin, Zo, and Vo with measured values in steps
2&3.
5. Bypassed RE of circuit in Figure 1 with a 1F capacitor as shown in Figure 2.
Compute Zin, Zo, Av, and Vo.
+Vcc
+9v
Rc
3.3K?
R1
47K?
C2
10F
=100
C1
10F
RL
10K?
2 Vpp
2KHz
RE2
1.5K?
R2
15K?
C3
100F
FIGURE 2
6. Set up the circuit of Figure 2. Measure and draw the output voltage. Also,
measure the input and output voltage.
+Vcc
+9v
Vin:
Zin:
Vo:
Zo:
Rc
3.3K?
R1
47K?
C2
10F
7. Compare your computed values for Zin, Zo, and Vo with measured
values in
step6.
=100
8.
2 Vpp
2KHz
C1
Compute10F
the
following parameters for circuit in Figure 4: IE, Zin, Zout, Av, Vo,
and maximum swing without distortion maxVo.
RL
10K?
RE1
100
R2
15K?
RE2
1.5K?
C3
100F
FIGURE 3.
9. Set up the circuit of Figure 3. This is the split (swamp0 emitter amplifier. Measure
the output voltage, Zin, and Zo. Draw the output voltage.
Vin:
Zin:
Vo:
Zo:
10. Compare your calculated values for Zin, Zo and output voltage with measured
values in step 9.
11. Turn off signal generator.
12. Turn off power supply.
V.
QUESTIONS TO PONDER
1. Compute the maximum output voltage w/o distortion of circuit in Figure 1.
Compare it with your measured Vo. Does your waveform has distortion? Why?
2. The maximum voltage w/o distortion bypassed emitter amplifier is 8.54 Vpp.
Compare it with your calculated Vo. Does your measured output waveform has
distortion? Why?
4. Make a comparison among the three types of voltage divider emitter amplifier
with respect to their voltages, waveforms, Zin, Zo and Av.
5. With proper design for each types of voltage divider emitter amplifier, which type
is more advantageous?