Escolar Documentos
Profissional Documentos
Cultura Documentos
e
Document Name:
CFR Section(s):
33 CFR 154
Standards Body:
Official Incorporator:
THE EXECUTIVE DIRECTOR
~~l~
Designation: F 1155 - 98
1. Scope
1.1 This practice is intended as a guide to shipbuilders,
shipowners, and design agents for use in the preparation of
piping system material schedules for commercial ship design
and construction.
1.2 The materials and limitations listed in Tables 1-28 meet
the minimum requirements of the U.S. Coast Guard and the
American Bureau of Shipping and should be considered to be
the minimum acceptable materials in regard to material,
design, and testing. This document is not intended to limit the
selection of material strictly to those listed. Other equal or
superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.
2. Referenced Documents
2.1 ASTM Standards:
A 53 Specification for Pipe, Steel, Black and Hot-Dipped,
Zinc-Coated Welded and Seamless2
A 105/A 105M Specification for Carbon Steel Forgings for
Piping Applications2
A 106 Specification for Seamless Carbon Steel Pipe for
High-Temperature Service2
A 134 Specification for Pipe, Steel, Electric-Fusion (Arc)Welded (Sizes NPS 16 and Over)2
A 139/A 139M Specification for Electric-Fusion (Arc)Welded Steel Pipe (NPS 4 and Overf
A 178/A 178M Specification for Electric-ResistanceWelded
Carbon Steel and Carbon-Manganese Steel Boiler and
Superheater Tubes 2
A 179/A 179M Specification for Seamless Cold-Drawn
Low-Carbon Steel Heat-Exchanger and Condenser Tubes2
A 181/A 181M Specification for Carbon Steel Forgings, for
General-Purpose Piping2
A 182/A 182M Specification for Forged or Rolled AlloySteel Pipe Flanges, Forged Fittings, and Valves and Parts
for High-Temperature Service2
A 192/A 192M Specification for Seamless Carbon Steel
Boiler Tubes for High-Pressure Service2
A 193/A 193M Specification for Alloy-Steel and Stainless
1 This practice is under the jurisdiction of ASTM Committee F-25 on Ships and
Marine Technology and is the direct responsibility of Subcommittee F25.13 on
Piping Systems.
Current edition approved April 10. 1998. Published July 1998. Originally
published as F 1155-88. Last previous edition F 1155-88 (1993i,plv II.
Annual Book of ASTM Stantklrds. Vol 01.01.
3 Annual
Book
Book
S Annual Book
6 Annual Book
4 Annual
482
of ASTM Standards.
of ASTM Standards.
of ASTM Standards.
of ASTM Standards.
Vol 01.02.
Vol 01.04.
Vol 15.08.
Vol 02.01.
~t F 1155
B 62 Specification for Composition Bronze or Ounce Metal
Castings6
B 88 Specification for Seamless Copper Water Tube6
B 466 Specification for Seamless Copper-Nickel Pipe and
Tube 6
B 467 Specification for Welded Copper-Nickel Pipe6
D 2996 Specification for Filament-Wound "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe7
D 2997 Specification for Centrifugally Cast "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe7
D 4024 Specification for Machine Made "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting Resin) Flanges7
F 682 Specification for Wrought Carbon Steel Sleeve-Type
Pipe Couplings8
F 683 Practice for Selection and Application of Thermal
Insulation for Piping and Machinery8
F 704 Practice for Selecting Bolting Lengths for Piping
System Flanged J oints 8
F 722 Specification for Welded Joints for Shipboard Piping
Systems8
F 1476 Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications 8
F 1548 Specification for the Performance of Fittings for Use
with Gasketed Mechanical Couplings Used in Piping
Applications8
2.2 ANSI Standards: 9
B16.5 Steel Pipe Flanges and Flanged Fittings
B16.9 Factor Made Wrought Steel Buttwelding Fittings
B 16.10 Face to Face and End to End Dimensions of Valves
B16.11 Forged Steel Fittings, Socket Welding and Threaded
B16.15 Cast Bronze Threaded Fittings Class 125 and 250
B16.18 Cast Copper Alloy Solder Joint Pressure Fittings
B16.22 Wrought Copper and Copper Alloy Solder Joint
Pressure Fittings
B16.24 Bronze Flanges and Flanged
B16.28 Wrought Steel Buttwelding Short Radius Elbows
and Returns
B16.34 Valves Flanged, Threaded and Welding End
B16.42 Ductile Iron Pipe Flanges and Flanged Fittings
B18.2.1 Square and Hex Bolts and Screws Inch Series
B18.2.2 Square and Hex Nuts (Inch Series)
B31.1 Power Piping
B36.10 Welded and Seamless Wrought Steel Pipe
B36.19 Stainless Steel Pipe
2.3 Manufacturer's Standardization Society of the Valve
and Fitting Industry Standards: lO
SP-67 Butterfly Valves
SP-72 Ball Valves with Flanged or Butt-Welding Ends for
General Service
SP-80 Bronze Gate, Globe, Angle and Check Valves
SP-83 Carbon Steel Pipe Unions, Socket-Welding and
Threaded
7 Annual
483
vm ll
ABS' Rules for Building and Classing Steel Vessels 12
Title 46, Code of Federal Regulations, Parts 41 to 69 13
NVIC 11-86; Guidelines Governing the Use of Fiberglass
Pipe (FGP) on Coast Guard Inspected Vessels 13
MIL-F-1183 Fittings, Pipe, Cast Bronze, Silver-Brazing l3
3. General Requirements
3.1 Shipboard piping systems shall be in accordance with
ANSI B31.1 except as modified by 46 CPR Part 56 of the U.S.
Coast Guard regulations and Sections 36 and 44 of the ABS'
Rules.
3.2 Piping systems shall be classed in accordance with 46
CPR 56.04.
3.3 Valves shall be in accordance with 46 CPR 56.20.
3.4 Valves for Class I systems shall be in accordance with
46 CPR 56.20-9(b) and if larger than 2-in. NPS shall not have
socket weld ends.
3.5 Resilient seated valves shall be in accordance with 46
CFR 56.20-15.
3.6 Dimensions of ductile iron gate, globe, angle, and check
valves shall be in accordance with ANSI B16.34 and shall use
the adjusted pressure temperature ratings of ANSI B31.1,
Appendix E.
3.7 Flanges for flanged valves and fittings and their companion flanges shall be in accordance with 46 CPR 56.25 and
56.30-10.
3.8 Bolting shall be in accordance with 46 CPR 56.25-20.
Practice F 704 shall be used as a guide for determining flange
bolting lengths.
3.9 Socket weld joints shall be in accordance with 46 CPR
56.30-5(c) and 56.30-10(b), Method 4, and shall not exceed
3-in. NPS for Class I and II-L service.
3.10 Threaded joints shall be in accordance with 46 CPR
56.30-20 and shall not exceed 2-in. NPS for Class I systems.
3.11 Flared, flareless, and compression tube fittings shall
be limited to 2-in. OD or below and shall be in accordance
with 46 CPR 56.30-25.3.12
3.12 Brazed socket type joints shall be in accordance with
46 CPR 56.30-30 and 56.75.
3.13 Gasketed mechanical couplings and fittings for use
with gasketed mechanical couplings shall be in accordance
with 46 CPR 56.30-35.
3.14 Flexible pipe couplings of the compression or slip-on
types shall be in accordance with 46 CPR 56.30-40.
3.15 For restrictions on the use of welded tube and pipe, see
46 CPR 56.60-2(b).
3.16 Ferrous pipe used for saltwater service shall be protected against corrosion in accordance with 46 CPR 56.60-3(a).
3.17 All welding of Class I and II piping shall be in
accordance with 46 CPR 56.70 and Specification F 722.
11 Available from American Society of Mechanical Engineers, 345 E. 47th St.,
New York, NY 10017.
12 Available from American Bureau of Shipping, Book Order, 45 Eisenhower
Dr., Paramus, NJ 07652.
13 Available from Superintendent of Documents, U.S. Govenunent Printing
Office, Washington, DC 20402.
4t F 1155
3.18 Thennal insulation for pIpmg systems shall be in
accordance with Practice F683.:
3.19 Fiberglass reinforced thennosetting epoxy resin pipe
and fittlhgs sllall be in accordance with 46 CFR 56.60-25 and
U.S. Coast Guard Navigation and Vessel Inspection Circular
(NVIC) 11-86.
3.20 Fiberglass pipe shall riot be used outboard of skin
valves.
4. List of Tables
Table
1
2
3
4
5
6
7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
5. Keywords
5.1 materials; piping systems; piping systems materials;
ship construction; ship design
8
9
484
~~ F 1155
TABLE 1 Material Temperature LlmltationsA
Material
Corrosion resistant
steel
Chrome-molybdenum
steel
Carbon steel
Ductile Iron
Bronze
Copper nickel alloy
Copper
Glass reinforced
plastic
Material Specifications
ASTM A 194/A 194M GR B 8, 8C, 8T
ASTM A 194/A 194M GR 8F
ASME SA312 Tp c 316L
ASME SA312 TP 304L
ASTMA351/A351M GR CF3M
ASTM A 1821A 182M GR F6a, F11
ASTM A 193/A 193M GR B16 .
ASTM A 193/A 193M GF B7
ASTM A 194/A 194 GR 4
ASME SA217 GR WC6
ASTM A 234/A 234M GR WP11
ASTM A 335/A 335M GR P11
ASTM A 387/A 387M
ASTM A 53 TYD S
ASTMA53 TY E
ASTM A 105/A 105M
ASTMA 106
ASTM A 134 GR 285C (straight seam)
ASTM A 134 GR 285C (spiral seam)
ASTM A 139/A 139M GR B (straight seam)
ASTM A 139/A 139M GR B (spiral seam)
ASTM A 181/A 181M
ASTM A 194/A 194M GR 2H
ASTM A 216/A 216M GR WCB
ASTM A 234/A 234M GR WPB
ASTM A 307
ASTM A 515/A 515M GR 70
ASTM A 395
A 536
ASME SB61
ASME SB62
ASME SB466 C70600
ASME S8467 C70600
ASTMB88TYKorL
ASME SB75
ASTM D 2996 GR 1
ASTM D 2997 GR 1
ASTM D 4024 GR 1
Temperature
Limit, of, max
1200
800
850
800
850
1100
1100
1000
900
1100
1100
1100
1000
800 E
650
800 E
800 E
300
200
300
200
800 E
800
1000
800
400
800
650
450
550
406
600
600
400
400
225
225
225
AMaxlmum temperature limits per ANSI 831.1 for all material, except glass reinforced plastic, which Is per NVIC 11-86 and Specification A 536 which is per 46 CFR 56.
BGR-grade.
OJ'P-tubular product.
~-type.
EUpon prolonged exposure to temperatures above 775F, the carbide phase or carbon steel may be converted to graphite.
485
4t F 1155
TABLE 2 ~team, Steam i)raJns, Bollei' Blow, Superheater Safety Valve Escape Piping
Item
Pipe
Takedown Joints
Bolting
Fittings
Type/Slyle
Design Specification
Material
Material Specification
Seamless
Flanges: weld neck or
socket weld
Bolts/bolt studs
Nuts
Flanged
CrMoB steel
CrMo steel
ANSI 836.10
ANSI B16.5
CrMoVo steel
CMo=steel
CrMo steel
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.5
Buttweld
Socket weld
Flanged or buttweld
CrMo steel
CrMo steel
CrMo steel
Socket weld
CrMo steel
Maximum Temperature
1100FA
Remarks/limitations
ANSI B16.34
AConsult applicable material and design specifications, and Taple 1 where indicated, to establish pressure/temperature ratings.
BCrMo-chromium-molybdenum.
'
C(>R-grade.
CrMoV--chromium-molybdenum-vanadium.
=CMo-carbon-molybdenum.
"For trim group definition, refer to Table 28.
TABLE 3 Steam, Steam Drains, Feed, Condensate Boller Blow Sampling and Compounding, Safety Valve Escape Piping
Item
Type/Style
Material
Material Specification
Design Specification
Pipe
Seamless or electric
resistance welded
Carbon steel
ANSI 836.10
Takedown Joints
Carbon steel
ANSI B16.5
Carbon steel
CrMoo steel
Carbon steel
Carbon steel
MSS-SP-83
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.5
Butt weld
Carbon steel
Socket weld
Carbon steel
Flanged or buttweld
Carbon steel
Carbon steel
Bolting
Fittings
Socket weld
A53 GR BTYcE
Limited to Ii design
pressure of 350 psig.
See,also Table 1.
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
BGR-grade.
orv-Iype.
CrMo-chromium-molybdenum
=For trim group definition, refer to Table 28.
486
Maximum Temperature
775FA
Remarks/limitations
Trim group 2=
4~ F 1155
TABLE 4 Steam, Steam Drains, Feed, Condensate, Boller Blow Sampling and Compounding, and Safety Valve Escape Piping
Item
Type
Style
Material Specification A
Design Specification
Pipe
Seamless or electric
resistance welded
Carbon steel
ASTM A 106 GR c B
ANSI B36.10
or A 53 GR B TY S or E
Takedown joints
Carbon steel
ANSI B16.5
Carbon steel
MSS-SP-83
Bronze
MIL-F-1183
Carbon steel
Carbon steel
Carbon steel
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.5
Buttweld
Carbon steel
Socket weld
Carbon steel
Sleeve couplings
Carbon steel
Threaded or brazed
Flanged
Bronze
Ductile iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 216/A 216M GR
WCB
or
ASTM A 234/A 234M GR
WPB
ASTM A 234/A 234M GR
WPB or A 105/A 105M
ASTM A 234/A 234M GR
WPB
ASME SB61 or SB62
ASTM A 395
Flanged or buttweld
Carbon steel
Socket weld
Threaded or brazed
Carbon steel
Bronze
Bolting
Fittings
ANSI B16.34
ANSI B16.34
MSS-SP-80 F
AWhen combining dissimilar materials, galvanic corrosion can occur, especially in seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
C(3R-grade.
Dtv-type.
EFor trim group definition, refer to Table 28.
FMSS-SP-80 valves limited to 75 % of valve design pressure.
Type/Style
Item
Pipe
Takedown joints
Bolting
Material
Material Specification
Design Specification
CrMo steel
CrMo steel
Commercial D
ANSI B16.5
CrMo steel
CrMoVE steel
CMoFsteel
Commerclal D
ANSI B18.2.1
ANSI B18.2.2
Seamless
CrMo steelB
Plate formed
Flanges: weld neck or
socket weld
Flanges: plate
Bolts/bolt studs
Nuts
ANSI 836.10
AConsult applicable material and design speCifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BCrMo-chromium-molybdenum.
C(3R-grade.
OSpecific Coast Guard and ABS approval for design required.
ECrMoV~hromlum-molybdenum-vanadium.
FCMo-carbon-molybdenum.
487
Maximum Temperature
1100FA
Remarks/Limitations
~t F 1155
tABLE 6 Gas Turbine and Diesel Exhaust Piping
Item
Pipe
Takedown joints
Bolting
Fittings
Type/Style
Material
Seamless or electric
resistance welded
Flanges: weld neck,
socket weld or slip-on
Flanges: plate
Bolts/bolt studs
Nuts
Flanged
Carbon steel
Buttweld
Carbon steel
Carbon steel
Carbon steel
CrMoDsteel
Carbon steel
Carbon steel
Material Specification.
Design Specification
ANSI 836.10
Commerclalo
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.5
ANSI B16.5
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
BGR-grade.
OSpeclfic Coast Guard and ABS approval required.
DCrMo-chromium-molybdenum.
488
Maximum Temperature
775 FA
Remarks/limitations
See Table 1
~~ F 1155
TABLE 7 Fresh Water for Auxiliary Machinery and Engine Cooling
Item
Pipe
Takedown joints
Bolting
Fittings
Type/Style
Seamless or electric
resistance welded
Filament wound
Centrifugally cast
Flanges: socket weld or
slip-on
Unions: socket weld or
threaded
Unions: threaded or
brazed
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Flanged
Material
Material Specificatlon A
FGpE
FGPE
Carbon steel
Commercial F
Commercial F
ANSI 816.5
Carbon steel
MSS-SP-83
8ronze
MIL-F-1183
GRpH
ASTM D 4024 GR 1
ASTM D 4024
Ductile iron
ASTM A536
ASTM F 1476
Carbon steel
ANSI 818.2.1
ANSI 818.2.2
ANSI B16.5
Carbon steel
8ronze
GRPH
Ductile iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 216/A 216M GR WCB
orA 105/A 105M
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASME S861 or SB62
Commercial
A536
ASTM F 682
MIL-F-1183
Commercial F
F 1548
Ductile irol)
ASTM A395
MSS-SP-67
Carbon steel
Carbon steel
Carbon steel
Buttweld
Socket weld or threaded Carbon steel
Ductile iron
ASTM A536
Sleeve couplings
Threaded or bra2;ed
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly wafer or lug
type
Butterfly grooved
end
Flanged
Flanged or buttweld
Ductile iron
Carbon steel
Valves: ball
Socket weld
Threaded or brazed
Grooved end
Flanged or buttweld
Carbon steel
Bronze
Ductile iron
Carbon steel
ASTMA395
ASTM A 216/A 216M GR WC8
orA 105/A 105M
ASTM A 105/A 105M
ASME SB61 or S862
ASTM A 536
ASTM A 216/A216M GR WCB
orA 105/A 105M or
A 181/A 181M
Valves
Design Specification
ANSI 836.10
ANSI 816.34
ANSI 816.34
ANSI 816.34
MSS-SP-80 J
Trim
Trim
Trim
Trim
MSS-SP-72
AWhen combining dissimilar materials, galvanic corrosion can occur especially in seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
CC3R-grade.
.
D'fY-type.
EFGP-fiberglass pipe.
FSpecific Coast Guard and ABS approval required.
"For U.S. flag vessels In addition to classification society requirements.
HGRP-glass reinforced plastic.
'For trim group definition, refer to Table 28.
"MSS-SP-80 valves limited to 75 % of valve design pressure.
489
Maximum Temperature
240FB
Remarks/limitations
group 3 and
group 3 and
group 3 and
group 3 and
4'
4'
4'
4'
~~ F 1155
TABLE 8 Fresh Water, Hot and Cold Domestic, Air Conditioning, Sanitary
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Valves: gate, globe,
angle, check
Valves: ball
Type/Style
Material
Material SpeclficationA
Design Specification
Seamless
Copper
ASTM B 88 TY c K or L
ASTM B88
Filament wound
FGp D
ASTM D 2996 GR E 1
Commercial F
Centrifugally cast
FGpD
ASTM D 2997 GR 1
CommercialF
Flanges: sllbraze
Unions: brazed or
threaded
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Boltslbolt studs
Nuts
Silbraze
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly wafer or lug
Butterfly grooved
end
Flanged or brazed
Bronze
Bronze
ASME SB62
ASME SB61 or SB62
ANSI B16.24
MIL-F-1183
GRpH
ASTM D 4024 GR 1
ASTM D4024
Ductile iron'
ASTMA536
ASTM F 1476
Carbon steel
Carbon steel
Copper
GRpH
Bronze
ASTM A 307 GR B
ASTM A 563 GR A
ASME SB8B TY K or L
Commercial
ASTM B 61 or B 62
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.22
CommerclalF
ASTM F 1476
Ductile Iron
Bronze
ASTMA395
ASTM B 61 or B 62
MSS-SP-67
Trim group 4 J
Trim group 4J
Bronze
MSS-SP-80 K
Trim group 4J
Bronze
MSS-SP-72
Trim group 4J
Flanged
AWhen combining dissimilar materials galvanic corrosionJcan occur, especially in seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
orv-type.
DFGP-flberglass pipe.
EGR-grade.
FSpecific Coast Guard and ABS approval required.
GFor U.S. flag vessels In addition to classification society requirements.
HGRP-glass reinforced plastic.
'Acceptable when gasket isolates coupling housings from fluid.
JFor trim group definition, refer to Table 2B.
KMSS-SP-80 valves limited to 75 % of valve design pressure.
490
~~ F 1155
TABLE 9 Sea Water Circulating, Wet Flremaln, and Distilling Plant Piping
Item
Pipe
Type/Style
Valves
Seamless or welded
Filament wound
Centrifugally cast
Flanges: brazed
Unions: brazed
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Flanged
Buttweld or welding
sleeve
Brazed
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly water or lug
Butterfly grooved
end
Flanged
Brazed
Takedown joints
Bolting
Fittings
Material Specification A
Material
Design Specification
CNA c 90:10
FGpD
FGpD
Bronze
Bronze
GRpH
Ductile Iron'
ASTMA536
ASTM F 1476
Carbon steel
Carbon steel
Bronze
CNA 90:10
ASTM A 307 GR B
ASTM A 563 GR A
ASME SB61 or SB62
ASME SB466 or SB467
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.24
810-1385880
Bronze
GRpH
Bronze
CNA
MIL-F-1183
Commercial F
ASTM F 1548
ASTM F 1548
Ductile iron"
Carbon steel"
MSS-SP-67
Bronze
ASTMA395
ASTM A 216/A 216M GR
WCB or A 105/A 105M
ASTM B 61 or B 62
Bronze
MSS-SP-80 L
Trim group 6K
Trim group 4 K
AWhen combining dissimilar materials, galvanic corrosion can occur, especially in seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
"CNA--<lopper nickel alloy.
DFGP-fiberglass pipe.
EGR-grade.
FSpecific Coast Guard and ABS approval required.
GFor U.S. flag vessels in addition to classification society requirements.
HGRP-glass reinforced plastic.
'Acceptable when gasket isolates coupling housings from fluid.
"Not permitted with CNA piping.
KFor trim group definition, refer to Table 28.
LMSS-SP~80 valves limited to 75 % of valve design pressure.
491
Maximum Temperature
150FB
Remarks/Limitations
Trim group 6 K
TABLE10 Dry Fire Main; Foam, Sprinkling, Deckwash, Tank Cleaning Piping
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Valves: gate, globe,
angle, check
Type/Style
Material SpecificationA
Material
Design Specification
ANSI B36.10
Carbon steel
ASTM A 106 GR c B or A 53
GR B TYDS or E
ASTM,A 105/A 105M
Carbon steel
MSS-SP-83
Ductile iron
ASTM A 536
ASTM F 1476
Carbon
Carbon
Carbon
Carbon
ANSI
ANSI
ANSI
ANSI
Carbon steel
Bronze
Ductile Iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASME SB61 or SB62
ASTMA536
Ductile Iron
Ductile iron
ASTMA395
ASTMA536
MSS-SP-67
Ductile Iron
Carbon steel
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASME SB61 or SB62
ASTMA536
ANSI B16.34
Seamless or electric
resistance welded
Flanges: socket weld or
slip-on
Unions: socket weld or
threaded
Gasketed
mechanical
couplings
Bo~sIbolt studs
Nuts
Buttweld
Socket weld
Carbon steel
Sleeve coupling
Threaded
Used with
Gasketed
mechanical
couplings
Butterfly wafer or lug type
Butterfly grooved
end
Flanged
Flanged or buttweld
Socket weld
Carbon steel
Flanged or threaded
Grooved end
Bronze
Ductile Iron
steel
steel
steel
steel
ANSI B16.5
B18.2.1
B18.2.2
B16.9 or B16.28
B16.11
ASTM F682
ANSI B16.15
ASTM F 1548
Trim group 4
Trim group 4
Trim group 3
ANSI B16.34
MSS-SP-80 F
AWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
OGR-grade.
orr-type.
For trim group definition, refer to Table 28.
FMSS-SP-80 valves limited to 75 % of valve design pressure.
492
Maximum Temperature
200FB
Remarks/limitations
~t F 1155
TABLE 11
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Type/Style
Material SpeciflcationA
Material
Design Specification
FGp E
Carbon steel
ASTM A 106 GR G B or A 53
GR B TVo S or E
ASTM D 2996 GR 1
ASTM D 2997 GR 1
ASTM A 105/A 105M
Commerclal r
Commercial r
ANSI B16.5
ANSI B16.5
MSS-SP-83
GRp l
Ductile Iron
ASTM D 4024 GR 1
ASTMA536
ASTM D4024
ASTM F 1476
Carbon steel
Carbon steel
Carbon steel
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
Carbon steel
Sleeve coupling
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly wafer or lug type
Carbon steel
GRp l
Ductile iron
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.9 or
B16.28
ANSI B16.11
Seamless or electric
resistance weld
Filament wound
Centrifugally cast
Flanges: slip-on or socket
weld
Flanges: plate
Unions: socket weld or
threaded
Flanges: adhesive bonded
Gasketed
mechanical
couplings
Bolts/boll studs
Nuts
Buttweld
Butterfly grooved
end
Flanged
Carbon steel
FGp E
Ductile iron
Carbon steel
Ductile iron
Threaded or brazed
Ductile iron
Carbon steel
Bronze
Grooved end
Ductile iron
ANSI B36.10
See NVIC 11-86 G
See NVIC 11-86 G
ASTM F682
Commercial r
ASTM F 1548
ASTMA395
ASTM A 216/A216M GR WCB
orA 105/A 105M
ASTMA536
MSS-SP-67
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASME SB61 or SB62
ASTMA536
ANSI B16.34
ANSI B16.34
MSS-SP-60K
Trim group 4J
AWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
CC3R-grade.
"TV-type.
':FGP-fiberglass pipe.
FSpeciflc Coast Guard and ABS approval required.
GFor U.S. flag vessels in addition to classification society requirements.
HNCA-nlckel copper alioy.
IGRP-glass-reinforced plastic.
JFor trim group definition, refer to Table 28.
KMSS-SP-80 valves limited to 75 % of valve design pressure.
493
Maximum Temperature
100F B
Remarks/Limitations
~t F 1155
TABLE 12 Diesel and Lube OIl.System Piping Fuel 011 Filling, Transfer, and Service Suction Piping
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Type/Style
Material
Design Specification
Maximum Temperature
200FA
Remarks/Limitations
ANSI B36.10
FGpD
FGpD
Carbon steel
ASTM A 106 GR B B or A 53 GR
B TYcS or E
ASTM D 2996 GR 1
ASTM D 2997 GR 1
ASTM A 105/A 105M
Carbon steel
MSS-SP-83
GRpG
ASTM D 4024 GR 1
ASTM D4024
Ductile iron
ASTM A 536
ASTM F 1476
Carbon
Carbon
Carbon
Carbon
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
Commercial
ASTM A 536
ANSI
ANSI
ANSI
ANSI
ASTM A 395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 536
MSS-SP-67
ASTM A 395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTMA536
ANSI B16.34
ANSI B16.34
Trim group 3 H
Seamless or electric
resistance welded
Filament wound
Centrifugally cast
Flanges: weld neck,
socket weld or slip-on
Unions: socket weld or
threaded
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Buttweld
Socket weld or threaded
Carbon steel
Sleeve couplings
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly wafer or lug
Carbon steel
GRpD
Ductile iron
Butterfly grooved
end
Flanged
Ductile iron
steel
steel
steel
steel
Ductile iron
Carbon steel
Ductile iron
Carbon steel
Socket weld or threaded Carbon steel
Grooved end
Material Specification
Ductile iron
CommercialE
Commercial E
ANSI B16.5
B18.2.1
B18.2.2
B16.9 or B16.28
B16.11
ASTM F 682
Commerclal E
ASTM F 1548
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BGR-grade.
crv-type.
DFGP-fiberglass pipe.
ESpecific Coast Guard and ABS approval required.
FFor U.S. flag vessel in addition to classification society requirements.
GGRP-glass reinforced plastic.
HFor trim group definition, refer to Table 28.
494
~t F 1155
TABLE 13 Fuel 011 ServIce DIscharge PIpIng
Item
Type/Style
Material
Carbon steel
ANSI B16.5
Carbon steel
MSS-SP-83
Ductile Iron
ASTM A 536
ASTM F 1476
Carbon
Carbon
Carbon
Carbon
ANSI
ANSI
ANSI
ANSI
Carbon steel
Ductile iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASTM A 536
Ductile iron
ASTM A536
Ductile iron
Carbon steel
Carbon steel
Grooved end
Ductile Iron
ASTM A 395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
orA 105/A 105M
ASTMA536
Seamless
Carbon steel
Takedown joints
Fittings
Valves
Valves: gate, globe,
angle, check
Design Specification
Pipe
Bolting
Material Specification
Sleeve couplings
Used with
gasketed
mechanical
couplings
Butterfly grooved
end
Flanged
steel
steel
steel
steel
ANSI B36.10
B18.2.1
B18.2.2
B16.9 or 916.28
B16.11
ASTM F682
ASTM F 1548
Trim group 4 D
ANSI B16.34
~-type.
495
ANSI B16.34
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
BGR-grade.
DFor trim group definition, refer to Table 28.
Maximum Temperature
300FA
RemarkS/Limitations
~tF 1155
TABLE 14 Cargo 011 and Vent Piping and Crude 011 Wash Piping
Item
Pipe
Takedown Joints
Type/Style
Seamless or electric
resistance welded
Filament wound
Centrifugally cast
Flanges: weld neck,
socket weld, or
threaded
Unions: socket weld
Flexible couplings
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Flanged
Bolting
Fittings
Buttweld
Socket weld
Valves
Design Specification
Commerclal E
Commerclal E
ANSI B16.5
Carbon steel
Steel with resilient
gasket
GRpG
MSS-SP-83
Commerclal E
ASTM D 4024 GR 1
ASTM D4024
Ductile Iron
ASTMA536
ASTM F 1476
Carbon steel
Carbon steel
Ductile Iron
Carbon steel
Carbon steel
Carbon steel
ASTM A 307 GR B
ASTM A 563 GR A
ASTMA395
ASTM A 216/A 216M
ASTM A 234/A 234M
ASTM A 234/A 234M
or A 105/A 105M
ASTM A 234/A 234M
Commercial
ASTMA536
ANSI B18.2.1
ANSI B18.2.2
ANSIB16.42
ANSI B16.5
ANSI B16.9 or B16.28
ANSI B16.11
Carbon steel
FGp D
FGPD
Carbon steel
Sleeve coupling
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly wafer or lug
Carbon steel
GRp G
Ductile iron
Butterfly grooved
end
Flanged
Ductile iron
Grooved end
Material Specification
Material
Ductile iron
Carbon steel
Ductile Iron
Carbon steel
Ductile iron
GR WCB
GR WPB
GR WPB
GR WPB
Maximum Temperature
200FA
Remarks/limitations
ANSI B36.10
See NVIC 11-861"
See NVIC 11-861"
ASTM F682
Commerclal E
ASTM F 1548
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTMA536
MSS-SP-67
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 536
ANSI B16.34
Trim group 4H
Trim group 3 H
Trim group 4 H
Trim group 4 H
Trim group 3 H
Trim group 3 and 4 H
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BGR-grade.
DrY-type.
DFGP-fiberglass pipe.
ESpecific Coast Guard and ABS approval required.
FFor U.S. flag vessel in addition to classification society requirements.
GGRP-glass reinforced plastic.
HFor trim group definition, refer to Table 28.
TABLE 15 Steering Gear Fill and Drain Piping, and Telemotor Piping
Item
Type/Style
Material
Material Specification
Design Specification
Maximum Temperature
406FA
Remarks/limitations
Pipe
Seamless
Copper
ASTM B 88 TVB K
ASTM B88
Takedown joints
Unions: brazed or
threaded
None required
Brazed or threaded
Brazed
Brazed or threaded
Bronze
MIL-F-1183
Bronze
Copper
Bronze
ANSI B16.18
ANSI B16.22
MSS-SP-80o
Trim groupD
Flanged
Bronze
MSS-SP-72, Table 2
Trim groupD
Bolting
Fittings
Valves: gate, globe,
angle, check
Valves: ball
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
Brv-type.
~SS-SP-80 valves limited to 75 % of valve design pressure.
DFor trim group definition, refer to Table 28.
496
~t F 1155
TABLE 16 Hydraulic Plplng AB
Item
Pipe
Type/Style
Seamless or electrio
resistance welded
Material
Carbon steel
Bolting
Fittings
Flanges: weldneck or
socket weld
Unions: flared, flareless,
oompression
Bo~s/bolt studs
Nuts
Buttweld
Socket weld
Valves: ball
Flared, flareless,
compression
Flanged
Design Specification
Carbon steel
ANSIB16.5
Carbon steel
Commeroial
Commercial"
CrMoFsteel
Carbon steel
Carbon steel
Carbon steel
ASTM A 193/A'193M GR G B7
ASTM A 194/A 194M GR 2H
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
orA 105/A 105M
Commercial
ANSI
ANSI
ANSI
ANSI
ANSI B16.34
ANSI B16.34
Carbon steel
Commercial"
Bronze
MSS-SP-72
CRESD
Takedown joints
Material Specificationo
ASTM A 106, A 178/A 178M,
A 179/A 179M, A 1921
A 192M orA 214/A 214M
ASTM A 213/A 213M or A 249/
A 249M
ASTM A 105/A 105M
Carbon steel
Carbon steel
Carbon steel
Remarks/Limitations
ANSI B36.10
B18.2.1
B18.2.2
B16.9 or B16.28
B16.11
Commercial"
Trim group 2H
AThis table does not apply to packaged hydraulic systems and equipment. For such applications, specific Coast Guard and ABS approval should be obtained.
BConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
"When combining dissimilar materials, galvanic corrosion can ooour, espeoially in seawater systems, and should be oonsidered.
DCRES-corrosion resistant steel.
"Speoifio Coast Guard and ABS approval required.
FCrMo-chromium-molybdenum.
GGR-grade.
HFor trim group definition, refer to Table 28.
497
~t F 1155
TABLE 17 Air Piping 150 psi and Below
Item
Pipe
Takedown joints
Bolting
Fittings
Type/Style
Seamless
Seamless
Filament wound
Centrifugally cast
Flanges: socket weld or
sllp-on
Unions: socket weld or
threaded
Unions: brazed
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Flanged
Material
Valves
Valves: gate, globe,
angle, check
Socket weld
Valves: ball
Brazed or threaded
Grooved end
Flanged
Design Specification
Carbon steel
Copper
FGpE
FGPE"
Carbon steel
ASTM A 106 GR c B
ASTM B 88 TV D K
ASTM D 2996 GR 1
ASTM D 2997 GR 1
ASTM A 105/A 105M
ANSI B36.10
ASTM B88
Commercial F
Commercial F
ANSI B16.5
Carbon steel
MSS-SP-83
Bronze
GRpH
MIL-F-1183
ASTM D4024
Ductile Iron
ASTMA536
ASTM F 1476
Carbon steel
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.34
Bronze
GRpH
Carbon steel
Ductile iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASME SB61 or SB62
Commercial F
ASTM A 234/A 234M GR WPB
ASTMA536
Ductile Iron
ASTM A 536
Ductile Iron
Carbon steel
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASME SB61 or SB62
ASTMA536
ASME SB61 or SB62
Carbon steel
Buttweld
Socketweld
Brazed
Adhesive bonded
Sleeve coupling
Used with
gasketed
mechanical
couplings
Butterfly grooved
end
Flanged
Material SpecificationA
Carbon steel
Bronze
Ductile iron
Bronze
ANSI B16.34
MSS-SP-80 J
MSS-SP-72
AWhen combining dissimilar materials, galvanic corrosion can occur, especially in seawater systems, and should be considered.
sConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
C(3R-grade.
orr-type.
EFGP-fiberglass pipe.
FSpecific Coast Guard and ABS approval required.
GFor U.S. flag vessels In addition to classification society requirements.
HGRP-glass reinforced plastic.
'For trim group definition, refer to Table 28.
"MSS-SP-80 valves limited to 75 % of valve design pressure.
498
Maximum Temperature
AmbientS
Remarks/Limitations
----
- -- - ----
~.-
~t F 1155
TABLE 18 Air Piping Above 150 psi
Item
Type/Style
Material
Material Specification
Design Specification
Pipe
Seamless or electric
resistance we Ided
Carbon steel
ASTM A 106 GR B B or A 53
GR B TV S or E
ANSI B36.10
Takedown joints
Carbon steel
ANSIB16.5
Carbon steel
MSS-SP-83
ASTMA536
ASTM F 1476
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.5
Ductile iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 216/A 216M GR
WCB or A 105/A 105M
ASTM A 234/A 234M GR
WPB
ASTM A 234/A 234M GR
WPB or A 105/A 105M
ASTM A 234/A 234M GR
WPB
ASTMA536
Ductile iron
ASTMA536
Bolting
Fittings
Ductile iron
Carbon steel
Carbon steel
Buttweld
Socket weld or threaded
Sleeve coupling
Used with
gasketed
mechanical
couplings
Butterfly grooved
end
Flanged
Socket weld or threaded
Valves: ball
Grooved end
Flanged or buttweld
Valves
Carbon steel
Ductile iron
Carbon steel
ASTMA216/A216M GR
WCB or A 105/A 105M
ASTM A 234/A 234M GR
WPB or A 105/A 105M
ASTM A536
ASTM A 216/A 216M GR
WCB or A 105/A 105M
orA 181/A 181M
Maximum Temperature
Ambient A
Remarks/limitations
A 53 GR B TV e E limited
to a design pressure of
350 psig
Trim group 4 D
ANSI B16.34
ANSI B16.34
MSS-SP-72
Trim group 3 D
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BGR-grade.
orr-type.
DFor trim group definition, refer to Table 28.
Item
Type/Style
Material
Material Specification
Design Specification
Pipe
Seamless
Copper
ASTM B 88 TVB K or L or
ASME SB75
Takedown joints
Bolting
Fittings
None
None
Brazed
Copper
ASTM B 88 TV K or L or
ASME SB75
ANSI B16.22
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
BTY-Iype.
499
Maximum Temperature
406FA
Remarks/limitations
Must be annealed for
pressures over 225
psig
~~ F 1155
TABLE 20 CO2 , Halon, and Smoke DetectIon
Item
Type/Style
Seamless or electric
resistance welded
Pipe
Takedown joints
Flanges: buttweld or
socketweld
Unions: socket weld or
threaded
Bolting
Bolts/bolt studs
Nuts
Fittings
Buttweld, socketweld or
threaded
Valves: gate, globe, Flanged or buttweld
angle, check
Socket weld or threaded
Material
Material Specification
Design Specification
Carbon steel
ANSI B36.10
Carbon steel
ANSI B16.5
Carbon steel
MSS-SP-83
CrMoDsteel
Carbon steel
Carbon steel
Carbon steel
B7
2H
WPB
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.9 or B16.28
WCB
ANSI B16.34
ANSI B16.34
Trim group 2E
WPB
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BGR-Grade.
orv-type.
DCrMo-chromium-molybdenum.
EFor trim group definition, refer to Table 28.
TABLE 21 SoundIng Tubes, Vents, and Overflows for Freshwater, Saltwater, and 011
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Valves: gate, globe,
angle, check
Type/Style
Seamless or electric
resistance welded
Filament wound
Centrifugally cast
Flanges: socket weld
or slip-on
Unions: socket weld
Flanges: adhesive
bonded
Gasketed
mechanical
couplings
Bo~slbolt studs
Nuts
Buttweld
Socket weld or
threaded
Sleeve couplings
Adhesive bonded
Used with
gasketed
mechanical
couplings
Butterfly grooved
end
Flanged
Socket weld
Brazed or threaded
Grooved end
Material
Material Specification A
Design Specification
Carbon steel
ASTM A 106 GR c B or A 53 GR
B TYDS or E
ASTM D 2996 GR 1
ASTM D 2997 GR 1
ASTM A 105/A 105M
Commercial F
Commercial F
ANSI B16.5
Carbon steel
GRpH
MSS-SP-83
ASTM D4024
Ductile iron
ASTMA536
ASTM F 1476
Carbon steel
ANSI
ANSI
ANSI
ANSI
GRpH
Ductile Iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
orA 105/A 105M
ASTM A 234/A 234M GR WPB
Commercial
ASTM A 536
Ductile Iron
ASTMA536
Ductile iron
Carbon steel
FGpE
FGpE
Carbon steel
Bronze
Ductile iron
ANSI B16.10
See Table 1 and NVIC
11-86 G
B18.2.1
B18.2.2
B16.9 or B16.28
B16.11
ASTM F682
Commercial F
ASTM F 1548
MSS-SP-80 J
AWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressureltemperature ratings.
"GR-grade.
orv-type.
EFGP-fiberglass pipe.
FSpecific Coast Guard and ASS approval required.
GFor U.S. flag vessels in addition to classification society requirements.
HGRP-glass reinforced plastic.
'For trim group definition, refer to Table 28.
~SS-SP-80 valves limited to 75 % of valve design pressure.
500
-----_.
------
-~~-
-- -
--- -- --
-- - -_.
-----
~t F 1155
TABLE 22 Waste, Soli, and Interior Deck Drains
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Valves: gate, globe,
angle, check
Valves: ball
Type/Style
Seamless or electric
resistance welded
Filament wound
Centrifugally cast
Material
Carbon steel
Material Specificatlon A
Design Specification
FGp E
FGP E
Commercial F
Commercial"
Carbon steel
ANSI B16.5
ANSI 836.10
See Table 1 and NVIC
11-86 G FGP not
permitted outboard
of shell valve.
MSS-SP-83
GRpH
ASTM D 4024 GR 1
ASTM D4024
Ductile Iron
ASTMA536
ASTM F 1476
Carbon steel
ANSI
ANSI
ANSI
ANSI
GRpH
Carbon steel
Ductile Iron
ASTM A 307 GR B
ASTM A 563
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
Commercial
ASTM F682
ASTM A536
Ductile Iron
ASTM A 536
Ductile iron
Carbon steel
Carbon steel
Brazed or threaded
Bronze
ASTMA395
ASTM A 216/A 216M GR WC8
or A 105/A 105M
ASME S861 or SB62
Grooved end
Flanged
Ductile iron
Ductile Iron
Bronze
ASTM A 395
ASME SB61 or SB62
818.2.1
B18.2.2
B16.9 or B16.28
B16.11
Commerclal F
ASTM F682
ASTM F 1548
ANSI B16.24
MSS-SP-80 J
ASTMA536
MSS-SP-72
AWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings
. C(3R-grade.
orv-type.
EFGP-fiberglass pipe.
FSpecific Coast Guard and ABS approval required.
GFor U.S. flag vessels in addition to classification society requirements.
HGRP-glass reinforced plastic.
'For trim group definition, refer to Table 28.
"MSS-SP-80 valves limited to 75 % of valve design pressure.
501
~~ F 1155
TABLE 23 Weather Deck Drains, Main Deck, and Above
Item
Pipe
Takedown joints
Bolting
Fittings
Valves
Valves: check
Type/Style
Material
Seamless or electric
resistance welded
Flanges: socketweld or
slip-on
Unions: socket weld
Gasketed
mechanical
couplings
Bolts/bolt studs
Nuts
Buttweld
Socket weld
Sleeve couplings
Used with
gasketed
mechanical
couplings
Butterfly grooved
end
Flanged
Grooved end
Material Specification
Design Specification
Carbon steel
ASTMA 106 GR s B or A 53 GR
BTYcS or E
ASTM A 105/A 105M
ANSIB16.5
Carbon steel
Ductile Iron
MSS-SP-83
ASTM F 1476
Carbon steel
ANSI
ANSI
ANSI
ANSI
Ductile Iron
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASTM A 536
Ductile Iron
ASTM A 536
Ductile Iron
Carbon steel
ASTMA395
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTMA536
Carbon steel
Carbon steel
Ductile Iron
Maximum Temperature
Ambient"
Remarks/Limitations
ANSI B36.10
B18.2.1
B18.2.2
B16.9 or B16.28
B16.11
ASTM F 682
ASTM F 1548
Trim group 4 0
ANSI B16.34
Trim group 40
Trim group 30
Trim group 3 and 40
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
sGR-grade.
"TV-type.
For trim group definition, refer to Table 28.
Item
Type/Style
Material
Pipe
Takedown joints
Bolting
Fabricated duct
Flanges: welded
Bolts
Alloy steel
Alloy steel
CrMoVo steel
Fittings
Valves
Valves
Nuts
Fabricated duct
Sliding gate
Butterfly wafer or lug
CMo F steel
Alloy steel
Carbon steel
Ductile iron
Material Specification
ASTM A 242!A 242M TV s 1
ASTM A 242/A 242M TV 1
ASTM A 193/A 193M GR E
B 16
ASTM A 194/A 194M GR 4
ASTM A 242/A 242M TV 1
Commercial c
ASTM A 395
Design Specification
Commercial C
Commerclal c
ANSI B18.2.1
ANSI B18.2.2
Commercial c
Commercial c
MSS-SP-87
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
srv-type.
CSpecific Coast Guard and ABS approval required.
CrMoV--<:hromium-molybdenum-vanadium.
EGR-grade.
FCMo--<:arbon-molybdenum.
GFor trim group definition, refer to Table 28.
502
Maximum Temperature
840FA
Remarks/limitations
Trim group 3G
Trim group 3G
I
~t F 1155
Type/Style
Item
Pipe
Takedown joints
Carbon steel
Seamless or electrio
resistance welded
Filament wound
Centrifugally cast
Flanges: weld neck socket
weld or slip-on
Flexible couplings
FGpE
FGpE
Carbon steel
Bolting
Fittings
Sleeve couplings
Adhesive bonded
Butterfly wafer or lug
Valves
Valves: gate, globe,
angle, check
Material Specification A
Material
ASTM D 4024 GR 1
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
Commercial
ASTM A395
ASTM A 216/A 216M GR WCB
orA 105/A 105M
ASTM A 395
ASTM A 216/A 216M GR WCB
orA 105/A 105M
ASME SB61 or SB62
Carbon steel
Carbon steel
GRpH
Ductile Iron
Carbon steel
Flanged
Ductile iron
Carbon steel
Flanged, brazed, or
threaded
Bronze
Maximum Temperature
406FB
Remarks/limitations
Design Specification
ANSIB36.10
Commercial F
Commercial F
ANSIB16.5
Commerclal F
ASTM D 4024
ANSI B18.2.1
ANSI B18.2.2
ANSI B16.9 or B16.28
ANSIB16.11
ASTM F 682
Commerclal F
MSS-SP-67
ANSI B16.34
MSS-SP-80 J
AWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
BConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
~R-grade.
~-type.
EFGP-fiberglass pipe.
FSpecific Coast Guard and ABS approval required.
GFor U.S. flag vessels in addition to classification society requirements.
HGRP-glass reinforced plastic.
'For trim group definition, refer to Table 28.
~SS-SP-80 valves limited to 75 % of valve design pressure.
TABLE 26 Llqulfled Natural Gas Systems Including Vapor Fuel, Inert Gas, and Nitrogen Service
Item
Pipe.
Takedown joints
Bolting
Fittings
Type/Style
Seamless or electric
resistance welded
Flanges: weld neck,
socket weld or slip-on
Bolts!bo~ studs
Nuts
Buttweld
Socket weld
Valves
Sleeve coupling
Butterfly wafer or lug
Flanged or buttweld
Socket weld
Material
Carbon steel
Carbon steel
Carbon steel
Carbon steel
Carbon steel
Carbon steel
Material Specification
Design Specification
ANSIB36.10
ASTM A 307 GR B
ASTM A 563 GR A
ASTM A 234/A 234M GR WPB
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
ASTMA216/A216M GR WCB
or A 105/A 105M
ASTM A 216/A 216M GR WCB
or A 105/A 105M
ASTM A 234/A 234M GR WPB
or A 105/A 105M
ANSIB18.2.1
ANSI B18.2.2
ANSI B16.9 or B16.28
ANSI B16.11
ANSI B16.5
ASTM F682
MSS-SP-67
ANSI B16.34
ANSIB16.34
AConsult applicable material and design specifications, and Table 1 where indicated, to establish pressure/temperature ratings.
BGR-grade.
~-type.
503
Minimum Temperature
OFA
Remarks/limitations
Trim group 3 D
~~ F 1155
TABLE 27 Llqulfled Natural Gas Systems Including Cargo, Inert Gas, Nitrogen, and Cargo Tank Cooldown and Warm-Up Piping Below
OaF
Item
Pipe
Takedown Joints
Bolting
Type/Style
Seamless or electric resistance welded
Flanges: weld neck or
sOQket weld
Bolts/bolt studs
Material
ANSI 836.19
CRES
ANSI B16.5
CRES
ANSI B18.2.1
CRES
Buttweld
Socket weld
Butterfly wafer or lug
CRES
CRES
Valves
Design Specification
CRESs
Nuts
Fittings
Material Specification
Minimum Temperature
-325FA
Remarks/limitations
ANSI B18.2.2
ANSI B16.9 or B16.28
ANSI B16.11
MSS-SP-67
Trim group 7c
ANSI B16.34
Trim group 7c
AConsult applicable material and design specifications, and Table 1 where Indicated, to establish pressure/temperature ratings.
sCRE8-corroslon resistant steel.
GrP-tubular product.
GR-grade.
cFor trim group definition, refer to Table 28.
2
3
4
5
6
7
8
Material
Trim
Stem
Wedge/disk
Seat ring
CRES O
CrMoc
CrMo
Seat, Integral
Stem, wedge/disk or seat ring
Integral seats
Stem, wedge/disk or seat ring
Seat Integral
Stem, wedge/disc or seating
Seat integ~al
Stem, wedge/disk or seat ring
Seat Integral
Stem, wedge/disk or seat ring
Stem, wedge/disk or seat ring
Same as valve
CRES
Same as valve
CRES
Same as valve
Bronze
Same. as valve
CRES
Same as valve
NCAF
CRES
Stem
Wedge/disk or seat ring
Integral seat
CRES
Bronze
Same as valve body
Material Specifications
ASTM A 1821A 182M GRoF6a
ASTM A 1821A 182M GR F11
ASTM A 1821A 182M GR F11 or ASME
SA217 GR WC6
Remarks/limitations
hard-faced seat
body
ASTM A 1821A 182M GR F6a
hard-faced seat
body
body
ASME SB61 or SB62
body
ASTM A 1821A 182M GR F6a
body
ASTMA 164G
ASTM A 1821A 182M GR F304L
or F316L or ASTM A 351/A 351 M
GRCF3M
ASTM A 1821A 182M GR F6a
ASME SB61 or SB62
AConsult applicable material and design speclficatiol)s',and Table 1 where Indicated, to 'establish pressurl!!/temperature ratings.
SWhen combining dissimilar materials, galvanic corrosion can occur, especially In seawater systems, and should be considered.
CCRE8-corrosion resistant steel.
.
GR-grade.
cCrMo-chromium-molybdenum.
FNCA-nickel copper alloy.
GDiscontinued.
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted In connection
with any Item mentioned In this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of Infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed evel}' five years and
if not revised, eIther reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
technical committee, which you may attend. If you feel that your comments have not received a fair hearIng you should make your
views known to the ASTM Committee on Standards, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
504