Escolar Documentos
Profissional Documentos
Cultura Documentos
I. Introduction
SD is quite easy to operate. The way to operate it is similar to cell phones. The function of Key 1 and Key
2 are correspondingly as the indication in the lower-left and the lower-right on the LCD. Thus you can operate
it according to the words on LCD easily.
In order to facilitate the use of the central controlling device, SD central controlling device upgrades many
advanced designs. It applies SD card as the vector to update data of the system. A USB interface and a piece of
SD card can be availed to update the data in the central controlling device easily. Humming is a hint for the
button setting. If the humming doesn't work, it means the key isn't pressed yet. Front operating table is shown
as fig.1.1.
Fig .1.1 The front operation table of the SD Central Controlling Device
1. Function Selecting
Select and confirm the menu function. The function is corresponding to the
indication in the lower-left of the LCD screen. Key 1 can be used to unlock the keyboard too.
2. Cancel and Return
Quit the present task and back to the menu one level up. The function is
corresponding to the indication in the lower-left of the LCD screen.
3. Page up Browse the pages ahead.
4. Page down Browse the pages below. Key 4 can also be used to unlock the keyboard.
5. Shift Up / Down Shift between the uplink and downlink information.
6. Trigger SOS If SOS=2shown in System Parameter,the key is used to trigger the function of SOS;
if SOS=3,the key need to work with external switch to trigger the function of SOS.
7. SD card interface
8. Photosensitive Probe
9. Direction indicator
228
UP
FC3
R
LOCK
228
UP
FC3
FUN
In
Lock
In
LIST
Unlock
Fig.2.1.1 Diagram of unlocking the keyboard
-----FUNCTION---Download Route
SELECT
EXIT
Download Route
Select Route
12.td5
SELECT
EXIT
Select the File of Lines
Download Route
Download OK
-----FUNCTION---Init Failure
Please Retry
RETURN
OK
No Card Inserted
Successful Updating
2.2.2 Updating the Line Information
Enter the SD card information, and then select the files which you want to update in the Lines Table by
using Page Up / Down. Press Key 1 to confirm the file you select. You can check the updating progress with the
progress bar. The prompt message Download OKwill be displayed when updating ends. Press Key 1 to
confirm and quit
Caution! Please make sure the SD card insert into the SD card slot during the process of updating. Draw
out the SD card when the updating ends up. In addition, due to the limitation of the LCD size of the central
controlling device, data file names with overlength cannot be overall displayed on the LCD screen. In order to
display the overall file names, you'd better not name it with a long name.
3. Query Board Hard
In this function list, the ways to operate the eight submenus "Front", "Rear Inter", "Inter",
"Side3","Side2","Rear Side","Side"and "Rear" are exactly the same. Take the "Front" as an example.
Connect the central controlling device to the anterior board (interface and ways to connect it will be
introduced in Part III). And then turn to pageQuery Board Hardand press Key 1 to enter the "Front". Press
Key 1 again and select " Query ", you will see the version of the size and software and hardware information of
the LED board. Press Key 2 to return. shown as fig.2.3.1.
EXIT
Return
FrontL:112
H:016
C1A1
M8S6
ANNV5.0 16120423
064KB MAX Return
2.3.1
4.Check Connect
Turn to pageCheck Connectand press Key1 to enter the state of Board connecting,which is shown as:
Check Connect
F C3
RETURN
5. Set LCD Contrast
Turn to pageset LCD contrastand press Key 1 to enter the state of setting LCD contrast. Which is shown as
fig.2.5.1.
EXIT
-----FUNCTION---Sys Parameter
SELECT
Sys Parameter
TP-02 1A1
SOS=2
TPLV5.0
111004
RETURN
EXIT
-----FUNCTION---Update Firmware
SELECT
EXIT
Update Firmware
00
Update Firmware
11
Update Firmware
no .tdh document
SET
SET
TLC-1
RETURN
RETURN
20110129
Update Firmware
Code 11
Update Firmware
SD Error
Update Firmware
document error 1
Update Firmware
Updating
TLC-1
TLC-1
TLC-1
20110129
20110129
20110129
Fig.2.7.1
8. Adjust the Lines
Press Key 2 to enter the table of Lines in the top level menu (the menu unlocked). Select the line name
you will set as the present line by using Page Up / Down key. Press Key 1 and select DETAIL, and then press
Key 1 to select HANDLE". At last press Key 1 to confirm and quit. Prompt messages are shown as fig.2.8.1.
228
UP
F R
FUN
228
567
SOS
DETAIL
In
228
UP
Set Current?
HANDLE RETURN
Select lines
EXIT
ENTER
RETURN
228
UP
F R
LOCK
In