Escolar Documentos
Profissional Documentos
Cultura Documentos
General
This set has an On-screen Service Menu system included in the CPU that allows remote operation for most of the
service adjustments.
NO.308
NO.309
NO.310
NO.311
NO.371
NO.372
R08
R09
R10
R11
(Adjust
(Adjust
(Adjust
(Adjust
the
the
the
the
data
data
data
data
FF
FF
FF
FF
to
to
to
to
21)
95)
50)
00)
FF to 00)
FF to A2)
Service Adjustment-1
1. Enter the Service Menu
While pressing the MENU button on the television, press the Number Key 2 on the remote control unit.
The Service Menu now appear.
MENU
S1.00110000
ADDRESS
02 H-PHA
Item No.
S2.01111000
DATA
08
Item
MENU
Data value
CHANNEL UP
2. Service Adjustments:
Press the CHANNEL UP or CHANNEL DOWN
button on the remote control handset to select the
desired service menu item you want to adjust.
VOLUME +
VOLUME -
CHANNEL DOWN
MENU
Service Adjustments
On-screen Service Menu
Following table shows the initial values which have been stored in the CPU ROM, and items for the service adjustments.
When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be checked
and be set up or readjusted according to the procedures described in the following pages.
Initial Setup Data marked with an * should be changed from Initial Value Data.
No.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Item
RFAGC
H-PHA
V-POS
V-SIZ
V-SCO
VLIN
H-P60
V-P60
V-S60
VSC60
VLI60
OSDHP
OSDC
V-SCP
SBIAS
RBIAS
GBIAS
BBIAS
RDRIV
GDRIV
BDRIV
-DRV
B-YD
R-YD
B-YND
R-YND
G-YA
RBGB
RBAG
G-YAN
RBGBN
RBABN
COGV
BLK
BLKG
BRTA
BRST
BRTH
WPL
YGAM
PORW
PORS
RFCO
PORWN
PORSN
TINT
SHRF
TEXC
AUFL
Initial value
Range
Description
0610*
08
32
54
1711*
1516*
+4
0
+1
0
+10*
30
50
07
70
00
00
00
6364*
0708*
6364*
--1008*
1008*
0
0
00
08
08
00
0
0
01
03
03
00
00
00
00
00
00
02
0
01
03
0
0
08
00
00~63
00~31
00~63
00~127
00~31
00~31
-16~+15
-32~+31
-64~+63
-16~+15
-16~+15
01~255
00~127
00~07
00~127
00~255
00~255
00~255
00~127
00~15
00~127
--00~15
00~15
-16~+15
-16~+15
00,01
00~15
00~15
00,01
-8~+7
-8~+7
00~03
00~03
00~03
00, 01
00, 01
00~07
00~03
00~03
00, 01
00~03
00~03
00, 01
00~03
-16~+15
-16~+15
00~127
00, 01
RF AGC adjustment
H-PHASE adjustment (50Hz)
Vertical position adjustment (50Hz)
Vertical size adjustment (50Hz)
Vertical-S compensation (50Hz)
Vertical linearity adjustment (50Hz)
Difference value of H-PHASE adjustment (60Hz)
Difference value of V-POSITION adjustment (60Hz)
Difference value of V-SIZE adjustment (60Hz)
Difference value of Vertical-S compensation (60Hz)
Difference value of Vertical linearity adjustment (60Hz)
OSD horizontal remark position
OSD contrast
V-SIZE COMP (50Hz)
Sub Bias adjustment
Red Bias adjustment
Green Bias adjustment
Blue Bias adjustment
Red Drive adjustment
Green Drive adjustment
Blue Drive adjustment
White balance (a lateral line)
Brightness and dark of White balance adjustment
B-Y DC Level
R-Y DC Level
Difference value of NTSC B-Y DC Level
Difference value of NTSC R-Y DC Level
G-Y Angle
R-Y/B-Y Gain Balance
R-Y/B-Y Angle
Difference value of NTSC G-Y Angle
Difference value of NTSC R-Y/B-Y Gain Balance
Difference value of NTSC R-Y/B-Y Angle
Coring gain
BLK. STR. Start (W/Defeat)
BLK. STR. Gain
BRT. ABL Defeat
Mid. Stp. Defeat
Bright. ABL. Threshold
WPL Ope. Point (W/Defeat)
Y Gamma Start
AV Mode Pre/Over SW
AV Mode Pre/Over-shoot adjustment
Difference Value of RF Corring Gain
RF Pre/Over SW
RF Pre/Over-shoot adjustment
Tint
Difference Value of RF Sharpness
OSD Text Contrast
Auto. Fresh
-9-
Service Adjustments
No.
Item
Initial value
Range
Description
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
300
301
302
303
304
305
306
307
308
309
310
311
312
COOP
Y-APF
DEEM
V-LVL
FMLVL
TTEST
IFOM-S
IFMN-S
IFTRPS
IFMLVL
VBSW
FBTS
HBLKL
HBLKR
AFCRF
VSURF
CDMRF
AFCAV
VSUAV
CDMAV
HLK-T
HLK-V
VCO-SW
VCOADJ
GRAY
CROSS
HL-SW
HL-TON
AVNCON
AVNBRI
POMT
CHMT
SYST
RELAY
CCD
TVAVTM
R00
R01
R02
R03
R04
R05
R06
R07
R08
R09
R10
R12
R13
07
01
00
04
16
00
00
00
01
136
00
00
06
04
00
00
00
0001*
00
00
00
00
00
03
00
00
01
00
64
64
1208*
1205*
03
8020*
2631*
00
FF93*
FF0E*
FF00*
FF00*
FF01*
FF00*
FF00*
FF00*
FF21*
FF95*
FF50*
FF00*
FF00*
00~07
00, 01
00, 01
00~07
00~31
00~07
00, 01
00, 01
00, 01
00~255
00, 01
00, 01
00~07
00~07
00, 01
00, 01
00~07
00, 01
00, 01
00~07
00, 01
00, 01
00, 01
00~03
00, 01
00~03
00, 01
00~03
00~127
00~127
00~127
00~31
00~255
00~255
00~31
00~255
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
00~FF
Colour Killer
Y-APF Select
De-emphasis TC
Video Level
FM Level
Trap Test
Over Mod. SW
Audio Monitor SW, Monitor/FM
IC Built-in SIF Trap ON/OFF
Video Level Coarse Adjustment & Mod. Operating Dot Setting
VBLK SW
FBP Blanking SW
H-Blanking Control Left
H-Blanking Control Right
Adjustment of AFC Gain & Gate (RF)
Adjustment of Vertical Sync. Separation Sensitivity (RF)
Vertical Count Down Loop Adjustment (RF)
Adjustment of AFC Gain & Gate (AV)
Adjustment of Vertical Sync. Separation Sensitivity (AV)
Vertical Count Down Loop Adjustment (AV)
H-lock, V-Det. (RF)
H-lock, V-Det. (AV)
C. VCO Adjustment SW
C. VCO Adjustment
Gray Mode
Cross Black/White
Half Tone ON/OFF
Half Tone Level
Contrast (No Signal in AV)
Brightness (No Signal in AV)
Power Mute Time
Channel Mute Time
System-N
Power Relay Time
Horizontal Remark Position Compensation Register
AV/TV Mute Time
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
370
371
372
R72
R72
R72
FF00*
FF00*
FFA2*
00~FF
00~FF
00~FF
ROM CORRECTION
ROM CORRECTION
ROM CORRECTION
-10-
Service Adjustments
Important Notice:
Do not attempt to adjust service adjustments not listed on below otherwise it may cause loss of performance and for
correct operation.
1.
2.
3.
4.
5.
Vertical size
Item
Vertical centre
A=B
-11-
Service Adjustments
Items 16-23 GREY SCALE
(1) Receive a monochrome circular pattern.
(2) Set the brightness and colour to normal, contrast to maximum.
(3) Enter to the service mode.
(4) Set each value of Item-16 RBIAS, 17 GBIAS, 18 BBIAS mode to 00. Set each value of Item-19 RDRIV, 21 BDRIV
mode to 63, 20 GDRIV to 07.
(5) Select Item-22 mode to be one horizontal scanning line and turn the screen volume on the FBT to obtain just visible
one coloured line.
(6) Press the 1 (Red Bias +), 4 (Red Bias -), 2 (Green Bias +), 5 (Green Bias -), 3 (Blue Bias +) or 6 (Blue Bias -)
button to adjust the brightness of each colour until a dim white line produced. Please see the control button allocations in this mode.
(7) Select Item-23 DRV mode to enter the white balance adjusting mode.
(8) Press the 7 (Red Drive +), RECALL (Red Drive -), 8 (Blue Drive +) or 0 (Blue Drive -) button alternately to
produce normal black and white picture.
(9) Exit from the service mode.
(10) Check for proper grey scale tracking at all brightness levels.
NOTE: If the grey scale adjustment is made after picture tube replacement, check the high voltage.
Green Bias +
Red Drive Blue Bias +
Green Bias Red Bias +
Blue Bias Red Bias -
Red Drive +
Blue Drive +
MAIN BOARD
T
D650
C628
R44
5
TP-B
R424
R474
C432
C355
R434
R423A
R435H1
Q432-H6
Q431
R435H2
Q432-H7
C433
L432
C465A
C425-H3
C425
C425-H2
C425A
C424A
C424
D439
C442A
KDY-1
R481
KDY
Q432-H5
-12-
C422
C420-H1
C486
L442
Q432-H4
(Under side)
C442-
C420A-H1
D485
SCREEN VR
JP436
C420B
C420
C486A
C422A
R488
C471
C487
C442-H3
C420-H3
C423-H1
JP486
C420-H2
D438
C423
C420A-H2
H-OUT
T471-H10
JP487
T471-H11
Q432-H1
Q432
C423A
T471-H9
C425-H1
(FBT)
F.B.T.
T471A
T471-H7
T471-H8
L462H2
C442-H1
C424-H1
C423-H2
Q432-H3
C
Q432-H2
C423-H3
T471-H6
L431
T471-H1
T471
C424-H3
T471-H3
T471-H2
C424-H2
T431
T431A
C434
T471-H5
C465
R355
T471-H4
R432
R433
JP476
C431
35
R4
C426 C426A
R423
C420A
R449
J145
JP488
R449A
C629
Q613-H6
Blue Drive -
KQ
R485
R487
Service Adjustments
Service Adjustment-2 (MTS Adjustment)
Following table shows the initial values of MTS Adjustment which have been stored in the CPU ROM.
No.
01
02
03
Item
INPUT LEVEL
HIGH SEPARATION
LOW SEPARATION
Initial value
08
21
34
Range
00~63
00~63
00~63
08
21
34
MENU
ADJUST: - /+
CHOOSE:
EXIT : MENU
MENU
2. Service Adjustments:
CHANNEL UP
VOLUME +
VOLUME -
CHANNEL DOWN
[ Service Adjustment ]
MENU
-13-
Service Adjustments
SOUND LEVEL ADJUSTMENT
R1912
JP029
+
C3422
J141
C3418
MTS
C3407
R037
J117
J118
R034
R3411
R3407
B6
C3404
005
55
C34
J125
C3412
13
C0
ADJUST: - /+
CHOOSE:
EXIT : MENU
12
R3412
J126
20
J143
C3416
C3413
10
R041
24
J101
R035
IC3401
C3420
PB1
C3436
R033
J075
25
C3414
C3431
IC3401
30
C042
C3423
R3422
R3421
J028
R3426
C3426
+
C3424
C3405 C3403
JP3404
JP3401
JP3403
36
C3401
C3421
JP0
R019
J030
J031
C3433
C3434
J092
C3439
R3432
J128
R658
40
08
21
34
JW4
C3417
37
C3432
C3427
J127
D1021
J137
R3433
JP3402
JP031
JP3405
48
INPUT LEVEL
HI SEPARATION
LOW SEPARATION
R042
J129
3
KL
JP1001
KR
3
JW1
J161
TP-317(pin-38 of IC3401)
1
1001
C3408
MAIN BOARD
(Solder side)
R1912
JP029
R3426
C3426
J141
+
C3422
C3421
C3418
C3420
MTS
R035
C3407
R037
J117
J118
R034
C3424
C3405 C3403
JP3404
JP3401
JP3403
C3433
C3434
PB1
C3436
C3431
R033
R3411
R3407
B6
C3404
R3412
005
C34
55
C3412
13
12
J125
J126
J143
20
R041
C3423
R3422
R3421
J028
R019
JP0
J030
J031
J161
J092
C3439
R3432
J128
J075
J101
24
C3416
10
C0
Minimum leakage
300Hz
-14-
C3414
25
C3413
ADJUST: - /+
CHOOSE:
EXIT : MENU
TP-317(R)
R65
IC3401
MAIN BOARD
(Solder side)
30
IC3401
JW4
C3417
36
40
C3401
48
08
21
34
C3427
37
C3432
C042
INPUT LEVEL
HI SEPARATION
LOW SEPARATION
JP3402
JP031
JP3405
R3433
R042
J129
3
KL
D1021
J137
KR
3
JW1
JP1001
TP-317(pin-38 of IC3401)
J127
1. Connect an oscilloscope:
Probe-A to TP-317 (pin-38 of IC3401) and the ground.
Probe-B to TP-318 (pin-39 of IC3401) and the ground.
C3408
Service Adjustments
6. Select HI SEPARATION by pressing the CHANNEL
UP/DOWN button on the remote control or TV set.
INPUT LEVEL
HI SEPARATION
LOW SEPARATION
08
21
34
ADJUST: - /+
CHOOSE:
EXIT : MENU
Minimum leakage
TP-318 (L)
4KHz
Service Adjustment-3
FINE TUNING
This adjustment is used to do a fine tuning of the channels with poor reception after they have been stored by the
automatic tuning.
This function is available for one channel only and the fine-tuned channel is memorized into IC802 (EEPROM).
MENU
MENU
MENU
FINE TUNING
2. Service Adjustments:
Press and hold the VOLUME + or VOLUME - button
on the remote control handset or TV set to make fine
tuning adjustment. Press and hold the VOLUME +
button for higher frequency tuning, and press and hold
the VOLUME - for lower frequency tuning.
VOLUME +
VOLUME -
[ Service Adjustment ]
-15-
MENU
Service Adjustments
Service Adjustment-4
FOCUS ADJUSTMENT
1. Receive the monochrome circular pattern.
2. Set the brightness to normal and contrast to maximum.
3. Adjust the focus control on the F.B.T. for the best focus
on the screen centre.
J059
62
J037
R524
J
IC501 VER
R512
R519
C520
D501
R357
R468
J057
L4
IC501-H4
R471
C518
Q461-H2
L441-H1
C441
JP43
C442
C420-H
L441 H2
J140
C441A
C442A
C423-H
C420A-H2
KDY-1
C441-H2
R473
L44
R462
IC501-H2
R472
R469
R528
D439
C441-H1
C442-H1
C425-H1
R441H1
C425
C425A
C424A
C424
JP441
Q461
L462H1
Q462
VR462
L462H2
VR463
C464
C462
C425-H3
C420A
Q461A E
C463
J015
C468A
R44
R441H2
C425-H2
C424-H3
L431
C424-H1
C423-H2
0
R464
61
466
C424-H2
C422
C420
C422A
R481
C
Q432-H2
R485
R487
R465
C465
C465A
Q432-H3
Q461-H1
R480
L461A
L432
C420-H3
L442
KDY
L461
C442-
C420A-H1
D485
J054
R434
R432
Q432-H7
JP436
C420-H2
C486
C487
Q431
C442A
C486A
C420-H1
R488
JP486
C471
T471-H11
C420B
C423-H1
JP487
Q432-H6
C442-H3
T471-H10
T471-H9
C431
C425A
D438
H-OUT
C423
C423A
T471-H7
T471-H8
Q432-H1
Q432
C420A-H2
C423-H3
F.B.T.
T471A
T471-H6
VR462
C425-H1
(FBT)
T471-H5
C425
C
Q432-H2
C442-H1
C424-H1
C423-H2
Q432-H3
T471
T471-H4
D439
T471-H1
T471-H2
C425-H3
C424A
L431
C424
C424-H3
1A
431
T471-H3
Horizontal Width
L462H2
Q432-H4
Q432-H5
KQ
R/G
D1901
VOL +
VOL -
CH +
CH -
C1902
SW1905
SW1904
SW1903
SW190
E
Q693
J142
R695
J065
C639
R650
D661
L654
14
11
16
R639
L653
J064
D652
C656
L616
J063
8
10
77
D639
L651
D651
E
Q625
J165
C6
R653
R624
D641
R652
L615
R643
R644
J144
C655
D611
C651
C652
R626
R625
C644
R662
J135
R664
J009
C618
TP +B +130V
Q612
T611A
R629
L612
R628
R103
L613
D650
C628
C629
R44
JP652
D469A
TP +B +130V
J079
C617
Q613-H6
R665
R661
R622
J012
Q642
L614
Q613
C657
T611B
Q611
D643
R623
D619
R616
Q641
R632
R631
R663
D614
C611
3
R63
D616
D617
R641
C615
R615
J010
D607
R619
R621
R620
C613
C609-H1
KH
R613
D654
C658
D653
CONVERTER
TRANS.
C614
R642
Protection Circuit
C66
D605
C609-H2
KG-1
KG-2
D610
D615
R614
+B ADJ.
R602-H4
R602-H3
R602-H1
R602A
R627
R611
C654
R602-H6
R602-H8
C605
C609
J062
J060
R602-H5
R602B
D606
C606
F601B
SW601-H4
C610
R602
R602-H7
R602-H2
W601
RL601
PS601A
2 KE-2
R601
C601A
F601A
D608
C608
Q691
J061
L601-H3
VR651
L601-H4
VR651
C693
L601-H2
D1902
JP601
KE-1
C601
L601-H1
PS601
KE
L601
VA60
1
T4AL250V
SW601-H2
R1907
J069
J032
A1901
MENU
SW1902
R4
PURITY ADJUSTMENT
1. Demagnetize the picture tube and receiver using an external
degaussing coil. When replacing picture tube or deflection
yoke, mount deflection yoke and purity-convergence magnets
assembly properly, see figures 1 and 4.
2. Turn Red and Blue guns off and provide only Green raster.
Rotate Screen control to fully counterclockwise. Rotate Red
and Blue Bias controls fully counterclockwise. Slowly rotate
Green Bias control clockwise to produce Green raster.
3. Loosen the screw holding the Deflection Yoke and remove the
3 Rubber Wedges, and slide the Deflection Yoke fully forward.
4. Rotate and spread the Tabs of the two Purity Magnets to centre the vertical green belt in the picture screen. The Purity
Magnets are also adjusted to obtain vertical centring of the
raster.
5. Slowly slide the Deflection Yoke backward until a uniform
green screen is obtained.
6. Check the purity of the red and blue screens for uniformity,
turn off other colours to check this (use bias controls).
Readjust the yoke position if necessary until all screens are
pure.
7. Adjust each Bias control and screen control to obtain white
raster. Refer to Gray Scale Adjustment. If part of the picture
screen is coloured, adjust the Deflection Yoke position forward
or backward slightly.
DEFLECTION YOKE
PURITY
MAGNET
TABS
SIX-POLE
MAGNET TABS
12
34
FOUR-POLE
MAGNET TABS
ANGLE
OF TABS
MAGNET TABS
FOCUS GAP
(G3-G4)
RUBBER
WEDGE
DEFLECTION YOKE
MOUNTING SCREW
RED
BLUE
GREEN
BLUE / RED