Escolar Documentos
Profissional Documentos
Cultura Documentos
Correct
Q.1) On the outside, a globe valve looks similar to what other valve?
A. Stop and waste valve
B. Angle valve
C. Gate valve (Your Answer)
D. Check valve
Wrong
Q.2) What mechanical operation is done to cut or form the fixture or individual parts
of the fixture?
A. Injection molding
B. Drawing
C. Reaming (Your Answer)
D. Stamping (Correct Answer)
Correct
Q.3) What chemical element in the steel increase the corrosion and stain-resistant
qualities of the fixture?
A. Nickel (Your Answer)
B. Copper
C. Iron
D. Aluminum
Wrong
Q.4) What thin line in the plan determine the depth requirments of sewers and water
services?
*
A. Cross-hatch
B. Contour (Correct Answer)
C. Broken (Your Answer)
D. Phantom
Wrong
Q.5) What is the best tool for cutting cast iron soil pipe that is rigidly in place?
*
A. Hacksaw (Your Answer)
B. Soil pipe cutter (Correct Answer)
C. Grinder
D. Hammer and chisel
Wrong
Q.6) What is the name of the tool used to remove pits or rough surfaces from valve or
faucet seats?
A. Seat driver
B. Seat reamer (Your Answer)
C. Seat dressing (Correct Answer)
D. Seat planning
Wrong
Q.7) What is meant by the term plumbo-solvent?
A. The ability of water to dissolve copper
B. The addition of chlorine to the water supply
C. The ability of water to dissolve lead (Correct Answer)
D. The use of lead-free solder fittings (Your Answer)
Correct
Q.8) What type of rigid copper pipe is the heaviest and is used for underground
waste?
A. Type K (Your Answer)
B. Type L
C. Type DWV
D. Type M
Correct
Q.9) What are used to keep harmful substances from entering the sanitary drainage
system?
A. Single dot
B. Double dot (Your Answer)
C. Continuous dotted line
D. Triple dots (Correct Answer)
Wrong
Q.13) What type of level er used by plumbers to install underground plumbing?
A. Line level (Correct Answer)
B. Pipe
C. Grade level (Your Answer)
D. Standard level
Wrong
Q.14) Aside from lavatory, what is the other common fixture that is provided with
overflows?
*
A. Kitchen sink (Your Answer)
B. Slop sink
C. Urinal
D. Bathtub (Correct Answer)
Correct
Q.15) What is the maximum distance (in feet) between hangers for 3 inches plastic pipe
installed in 20 foot lengths?
A. 5
B. 4 (Your Answer)
C. 2.5
D. 6.5
Wrong
Q.16) What tool is used to cut copper, brass, aluminum, or plastic tubing, and thin-wall
conduit?
*
A. Hacksaw (Your Answer)
B. Flaring tool
C. Pipe tap
D. Tubing cutter (Correct Answer)
Correct
Q.17) Which fitting is NOT necessary in the installation of the house service?
*
A. Corporation stop
B. Meter stop
C. Curb stop (Your Answer)
D. Water mater
Correct
Q.18) What part of a pipe curves like the neck of a goose, and is flexible?
*
A. E-curve
B. Snake
C. Goose neck (Your Answer)
D. Auger
Correct
Q.19) When fixtures are constructed of previous material, what specific condition is
permitted?
A. Unsatisfactoey Quality
B. Inaccessibility of parts to be cleaned
C. Waste outlet that can retain water (Your Answer)
D. Smooth substance
Correct
Q.20) If one of the two weights associated with cast-iron is service weight, what is the
other weight?
Q.21) What is the minimum length of time (in hours) before a jointed plasteic pipe be
subjected to pressure test?
A. 1 (Your Answer)
B. 3
C. 2 (Correct Answer)
D. 4
Correct
Q.22) What do lines on isometric drawing represent?
*
A. Valves and vents
B. Pipe and fittings (Your Answer)
C. Pipe and fixtures
D. Fixtures ang fittings
Wrong
Q.23) What is the CORRECT and MOST accurate way to measure out lengths of
pipe?
*
A. Center-to-face
B. Center-to-center (Your Answer)
C. End-to-end
D. End-to-center (Correct Answer)
Wrong
Q.24) What is the primary purpose of valving?
A. Change the direction of fluid flow (Your Answer)
B. Adjust pipe sizes
C. Deliver fluid
D. Regular fluid flow (Correct Answer)
Wrong
Q.25) What is the function of by pass valve?
Correct
Q.26) What tool is favored by some plumber for cutting plastic pipe?
*
A. Universal saw (Your Answer)
B. Circle saw
C. Adjustable wrench
D. Pipe wrench
Correct
Q.27) What type of a joint is a compression coupling?
*
A. Mechanical (Your Answer)
B. Threaded
C. Illegal
D. Screw
Wrong
Q.28) Which of the following plumbing fixtures is the MOST commonly used?
A. Kitchen sink (Your Answer)
B. Water closet (Correct Answer)
C. Lavatory
D. Shower
Correct
Q.29) What is the name of the process in which steel and wrought iron pipe rust?
*
A. Oxidation
B. Cavitation
C. Tuberculation (Your Answer)
D. Sublimation
Correct
Q.30) What is the recommened support spacing of vertically installed pipe?
A. 4ft (Your Answer)
B. 3ft
C. 6ft
D. 2ft
Correct
Q.31) Which of the following factors is NOT considered in sizing the water supply
piping?
*
A. Length of the pipe in the building
B. Pressure of the water supply at the source
C. Number and kind of fixtures installed
D. Pipe friction (Your Answer)
Correct
Q.32) What strength of a hook should you choose in selecting a hook and chain that
are to be used for lifting pipes?
A. Leader
B. Drain
C. Riser
D. Stack (Your Answer)
Wrong
Q.37) On what point of the pipe cross-section is the pipes elevetion referred to?
*
A. Top of pipe
B. Center of pipe (Your Answer)
C. Invert (Correct Answer)
D. Bottom pipe
Wrong
Q.38) What happens when moist air is trapped in a horizontal vent pipe?
A. Can block the passage of warm air into the system (Your Answer)
B. Being dense, the plumbing sysytem is disturded
C. Can cause corrosion on the pipe (Correct Answer)
D. Can lead to the creation of vacuum spaces
Correct
Q.39) When are traps prohibited?
A. If they are of inverted type
B. If they do not depend on interior partitions or moving parts for action
C. If they are over 4 inches in diameter
If they depend on concealed interior partitions or moving parts for action
D.
(Your Answer)
Wrong
Q.40) Which can cause obstruction of the flow of wastes in a drainage piping?
A. Pocket of neutral pressure
B. Pressure differential
C. Pocket of positive and negative pressures (Your Answer)
D. Pocket of low or high pressure (Correct Answer)
Wrong
Q.41) Other than making a quiet and peaceful house, what is prevented when water
hammer will be eliminated?
A. Material defect
B. Unsafe acts (Your Answer)
C. Unsafe conditions
D. Ignorance
Wrong
Q.45) What could be a sulotion to a restricted water flow of faucet?
*
A. Replace or filter screen (Correct Answer)
B. Smooth out lever nut
C. Re-adjust valve (Your Answer)
D. Clean or replace hose head valve
Correct
Q.46) What tool is used for expanding the ends of lead pipe?
A. Drift plug
A. Caulking
B. Soldering
C. Welding
D. Threading (Your Answer)
Wrong
Q.49) What common support is used to keep vertical pipe in alignment?
A. Vent piping
B. Vertical (Correct Answer)
C. Horizontal (Your Answer)
D. Waste piping
Correct
Q.50) Which of the following is NOT a type of sink?
A. Service
B. Perforated (Your Answer)
C. Flushing rim
D. Scullery
Correct
Q.51) Which are parts of water closet?
What kind of pipe is generally designed for underground gas distribution and for
other underground services?
*
B. Isometric 90 degrees up
C. Plan view 90 degrees down
D. Plan view 90 degrees away
Correct
Q.57) What do you call the primary vent in a venting system to which various vent in a
venting system to which various vent branches are connected?
*
A. Main vent (Your Answer)
B. Yoke vent
C. Vent Stack
D. Stack vent
Wrong
Q.58) When water heater is a combibation potable water heater and space heater, ho must
potable water be maintained?
A. At moderate temperature
B. At a cool temperature (Your Answer)
C. At a warm temperature
D. Throughout the syytem (Correct Answer)
Correct
Q.59) On a sanitary waste line, what is located is located in an accessible area and attaches
to the end of the waste pipe in the direction opposite of flow?
*
A. Clean out (Your Answer)
B. Sewer pipe
C. Vent pipe
D. Floor drain
Correct
Q.60) Why do mostwall-hung urinals Not require a trap?
*
A. They are designed to have integral trap (Your Answer)
B. Because such fixtures seldom receive solid waste
C. Traps are already provided down the soil pipe
Siphonic action that occurs in wall-hung urinals during flushing prevents the
D.
usage of traps
Wrong
Q.61) What device is used to raise the temperature of some of the domestic water supply
for use in various fixtures?
*
A. Temperature increaser
B. Hot water heater (Correct Answer)
C. Thermostat (Your Answer)
D. Heating elament
Correct
Q.62) Which is NOT an essential need in designing and in reading a blueprint?
A. Abbrevations
B. Binoculars (Your Answer)
C. Blueprint symbols
D. Mathematical table
Wrong
Q.63) What type of rigid copper pipe is lightweight?
A. Type DWV
B. Type L (Your Answer)
C. Tyep M (Correct Answer)
D. Type K
Wrong
Q.64) Which of the following materials composition describe a 95/5 solder?
A. 95% tin-5% zinc
B. 95% lead-5% zinc (Your Answer)
C. 95% tin-5% antimony (Correct Answer)
D. 95% lead-5% antimony
Correct
Q.65) What do you call the drains which serve one or more fixtures that discharge into
another drain or into a stack?
*
A. Fixture drains
B. Horizontal Branches
C. Wet vents
D. Fixture branches (Your Answer)
Correct
Q.66) Which of the following does the feed cister supply water?
*
A. Fixture schedule
B. Item number/letter
C. Fixture label (Your Answer)
D. Fixture ID
Wrong
Q.77) What conveys foul air from a plumbing fixture or a room to the outer air?
A. Stack vent (Your Answer)
B. Leader
C. Riser
D. Local vent (Correct Answer)
Wrong
Q.78) What are the products of complete combustion of natural gas?
*
A. Hydrogen and methane
B. Water vapour and carbon dioxide (Correct Answer)
C. Oxygen and carbon monoxide
D. Carbon dioxide and carbon monoxide (Your Answer)
Correct
Q.79) According to the international Plumbing Code, above what temperature can you
consider water as hot water?
*
A. 60 deg C
B. 120 deg F (Your Answer)
C. above room temperature
D. 212 deg F
Correct
Q.80) What is the minimum size (in inches) of traps used on a kitchen sink waste pipe?
A. 2
B. 2.5
C. 1
D. 1.5 (Your Answer)
Wrong
Q.81) What type of shower provides a means for quick rinsing of a person's skin that may
have been exposed to a toxic or harmful chemical?
*
A. Health care
stone?
*
A. Cold chisel (Your Answer)
B. Diamond nose chisel
C. Cape chisel
D. Gouge
Correct
Q.87) What device utilize the water delivered by the water supply system?
*
A. Plumbing riser
B. Plumbing fixture (Your Answer)
C. Plumbing pipe
D. Plumbing vent
Correct
Q.88) Which are prevented by fixture trap seals?
A. Excessive draining
B. Siphonage and backpressure (Your Answer)
C. Free-flowing effluents
D. Overflows
Wrong
Q.89) Riser diagram which are elevations or perspective views showing stacks an risers
generally indicate what kind of jobs?
A. Simple (Your Answer)
B. Non-complicated
C. Complicated (Correct Answer)
D. Easy
Wrong
Q.90) what is the suitable gasket material for a flange union used in gasoline
conduction?
*
A. Metallic or rubber composition
B. Metallic (Correct Answer)
C. Rubber or asbestos sheet
D. Rubber or asbestos composition (Your Answer)
Correct
Q.91) Which of the following pipes receives the discharge from a water closet and
conveys it to a soil stack or the building drain?
*
A. Waste
B. Drain
C. Vent
D. Soil (Your Answer)
Correct
Q.92) Which of the following methods of jointing plastics used for discharge pipework
systems is BEST described as a cold welding process?
A. Solvent welding (Your Answer)
B. Fusion welding
C. Compression welding
D. Branch Welding
Correct
Q.93) Which of the following is NOT among the basic angles necessary to express the
sanitary planning system in an isometric drawing?
*
A. Horizontal pipe
B. Sixty degree angle pipe (Your Answer)
C. Vertical pipe
D. Forty-five degree angle pipe
Correct
Q.94) Which of the following statements is NOT true in water heaters?
*
A. The discahrge pipe from a relief valve must be trapped. (Your Answer)
When water haeters are installed in locations where leakage of the tank or
B.
connections will cause damage, the water heater must be installed in a pan.
All water heaters must be provided with an approved, self-closing (levered)
C.
pressure relief valve and a temperature relief valve, or a combination thereof.
D. Water heaters must be protected to prevent siphoning of its contents.
Wrong
Q.95) What step must be undertaken to avoid encountering airline cracks on the soldered
joint of a hot water supply system when the water is turned on?
A. Use a solder type that is suited for a particular fitting and pipe (Your Answer)
B. Apply heat evenly on the fitting before placing the solder on slot holes
C. Thoroughly clean the joint to be soldered
D.
Faucets should be opened on the downstream side to relieve pressure on the line
before soldering (Correct Answer)
Correct
Q.96) What pipe is indicated in the plumbing plan having a series of dashes with letter
V separating the dashes?
A. Vacant
B. Vent
C. Vinyl
D. Vacuum (Your Answer)
Correct
Q.97) When two or more fixtures are permitted to use a single trap, what is the waste pipe
for installation called?
A. Individual
B. Continous waste (Your Answer)
C. Common waste
D. Sewer
Correct
Q.98) What must a pipe pass through when it penetrates an exterior wall?
A. Cotrol valve
B. Protection pad
C. Adapter
D. Sleeve (Your Answer)
Wrong
Q.99) What device is used to ream burs out of pipe that has been cut?
*
A. Bolt cutter
B. Pipe reamer (Correct Answer)
C. Wood chisel
D. Cutter wheel (Your Answer)
Wrong
Q.100) What minimum clear distance is required whenever the water service supply pipe
will be laid on the same trench within the sewer line?
C. 3 Foot
D. 2 1/2 Foot
Wrong
Q.101) Which of the water closets is the most efficient, the quietest and the most
expensive?
*
A. Siphon jet (Your Answer)
B. Reverse trap
C. Valve
D. Siphon action (Correct Answer)
Wrong
Q.102) How should fixtures be located in order to essure of the most economical
installation?
A. Parallel to teach other
B. With less bends and curves
C. Along a straight line (Your Answer)
D. As close together as possible (Correct Answer)
Correct
Q.103) Which of the following fixtures does NOT belong to the group.
*
A. Hose bibb
B. Water spigot
C. Water cooler (Your Answer)
D. Water faucet
Correct
Q.104) Which of the following pipes provides a flow of air to or from a drainage system to
provide a ciculation of air within the system?
A. Soil
B. Vent (Your Answer)
C. Drain
D. Waste
Unanswered
Q.105) What pipe idicated in the plumbing plan with a solid line?
A. Drain (Correct Answer)
B. Hot water reciculating
C. Vacuum
D. Fire protection
Wrong
Q.106) What device prevents excessive vacuum in a pressure vessel?
A. Vacuum pump
B. Vacuum Breaker (Your Answer)
C. Vacuum pressure preventer
D. Vacuum relief valve (Correct Answer)
Correct
Q.107) What tool is used to make holes in stainless steel sinks?
*
A. Cutter wheel
B. Wood chisel
C. Bolt Cutter
D. Knockout set (Your Answer)
Wrong
Q.108) What type of pipe joints consists of a soft metal alloy of tin and lead with a low
melting point?
A. Butt-weld
B. Solder (Correct Answer)
C. Threaded
D. Compression (Your Answer)
Correct
Q.109) What drain serves a single fixture trap?
A. Individaul drain
B. Fixture branch
C. Horizontal branch
D. Fixture drain (Your Answer)
Wrong
Q.110) What kind of test is used in determining whethergalvanized pipe is made of
wrought iron or wrought steel?
A. Smoke
B. Hammer (Correct Answer)
C. Water