Escolar Documentos
Profissional Documentos
Cultura Documentos
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
Search
Custom Search
Available
Categories
M obile devic es > G P RS for mobile internet > C hapter 4 : Radio I nterfac e: P hys ic al L ayer > RF P hys ic al L ayer
Adobe
Macromedia
Programming
www.SignalHound.com
SQL
Server
Administration
Networking
Microsoft
Products
Mac OS
RF Physical Layer
4.2 RF Physical Layer
Certification
This section first describes the concept of multislot classes, which allows for transmission in several time slots
in the TDMA frame. It then focuses on the transmitter and receiver requirements. For the former, the
constraints introduced by multislot transmissions are presented. For the latter, the sensitivity and interference
performance specifications are discussed, as well as GSM circuit-switched requirements such as blockings,
intermodulation, and AM suppression, which also apply in GPRS Release 99. The transmitter and receiver
requirements are defined in [1].
Misc
Linux systems
Mobile devices
XML
Available
Tutorials
GPRS for mobile
internet
Mobile and
wireless design
essentials
Mobile location
services.the
definitive guide
Mobile vpn.
delivering
advanced
services in next
generation
wireless systems
One of the most important GPRS characteristics on the air interface is the possibility of increasing the
achievable bit rate by grouping together several channels. In order to do so with a reasonable impact on the
MS in terms of implementation complexity, it has been decided to allow the RF transmission on several slots of
a TDMA frame, with a number of restrictions, as listed below.
Several bursts can be transmitted within a TDMA frame, but should all be on the same ARFC number
(ARFCN; i.e., the same carrier frequency).
Depending on the mobile capability, delay constraints are needed between the transmission and reception
of bursts, and between reception and transmission, to allow the mobile to perform the adjacent cell
measurements, or monitoring, as discussed in Chapter 1.
If there are m time slots allocated to an MS for reception and n time slots allocated for transmission, the
system requires that min (m,n) reception and transmission time slots have the same time slot number (TN;
see Section 1.5.1 for the definition) within the TDMA frame.
Two types of MSs are defined: type 1 mobiles are not able to transmit and to receive at the same time, while
type 2 mobiles are. For these two types, there exist different classes, depending on the capability of the MS
in terms of complexity. The classes are called multislot classes since they refer to the ability of the mobile to
support a communication on several time slots of the TDMA frame. For a given multislot class, the mobile is
able to transmit on a maximum of Tx time slots, and to receive on a maximum of Rx time slots within a TDMA
frame, but the sum Tx + Rx is limited. This means that the maximum of Tx slots and the maximum of Rx slots
are not active at the same time.
The definition of the type 1 multislot classes relies on the following time constraints:
T ta is the maximum number of time slots allowed to the MS to measure an adjacent cell received signal and
to get ready to transmit. This parameter is therefore used to set the minimum allowed delay between the
end of a transmit or receive time slot and the next transmit time slot, with an adjacent cell measurement
to be performed in between.
T rb relates to the number of TS needed by the MS, prior to a receive time slot, when no adjacent cell
measurement is performed. It is the minimum delay between the end of a transmit or receive TS and the
first next receive TS.
T ra is the minimum allowed delay in number of TS, between the end of a transmit or receive time slot and
the next receive time slot, when an adjacent cell measurement is to be performed in between.
T tb is the minimum number of TS between the end of a receive or transmit TS and the first next transmit
TS, without adjacent cell measurement in between.
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
1/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
These constraints have been chosen to give the mobile enough time for the frequency change between a
receive or transmit slot, and the next receive or transmit slot. It also allows some time to measure an
adjacent cell received signal level, which requires a measurement window (the window size is usually in the
order of one time slot or less) and two frequency changes (from the transmit or receive frequency to the
adjacent cell beacon frequency, and then back to the next receive or transmit time slot). Note that the time
constraints T ta and T tb may be reduced by the amount of the TA, to derive the allowed time duration before
transmission.
The existing multislot classes are given in Tables 4.7 (type 1 MSs) and 4.8 (type 2 MSs), with the Tx and Rx
parameters defining the maximum uplink and downlink slots of the TDMA frame, the sum being the maximum
value for Rx + Tx. The time constraints T ta , T rb, T ra , T tb corresponding to each class are also given in these
tables.
Table 4.7: Type 1 MS Multislot Classes
Type 1 MSs
Maximum Number of Slots Minimum Number of Slots
Multislot Class Rx
Tx
Sum Rx+Tx
Tta
Ttb
Tra
Trb
10
11
12
19
N/A
[a]
[b]
20
N/A
[a]
[b]
21
N/A
[a]
[b]
22
N/A
[a]
[b]
23
N/A
[a]
[b]
24
N/A
[a]
[b]
25
N/A
[a]
[b]
26
N/A
[a]
[b]
27
N/A
[a]
[b]
28
N/A
[a]
[b]
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
2/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
29
N/A
[a]
[b]
Tx
Sum Rx+Tx
Tta
Ttb
Tra
Trb
13
N/A
N/A
([*])
([*])
14
N/A
N/A
([*])
([*])
15
N/A
N/A
([*])
([*])
16
N/A
N/A
([*])
([*])
17
N/A
N/A
([*])
18
N/A
N/A
Note that only one monitoring window (i.e., an adjacent cell power measurement window) is needed in a TDMA
frame, so that only a couple (T ra ,T tb) or (T ta ,T rb) is needed to define a valid configuration of a given multislot
class. Figure 4.11 further illustrates the different possible configurations allowed for a class 12 mobile.
3/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
as well as the power control ranges and steps. The changes due to GPRS on Tx are limited to the constraint
of the multislot transmission, with a new power ramping template. Indeed, as seen in Section 4.1.3, power
control is used on uplink, and independent transmit power on adjacent time slots, and therefore any
combination of power control steps may be applied on several time slots of the same TDMA frame. The single
slot power versus time mask is shown in Chapter 1, in Figure 1.11, for the NB.
Figure 4.12: Multislot power versus time mask for the NB and for the AB- (a) power level is higher on first time
slot; and (b) power level is higher on second time slot.
4.2.3 Receiver Path Characteristics
4.2.3.1 Reference Sensitivity Performance
In the case of GSM circuit-switched services (see Section 1.5.6.2), a minimum input level at the receiver is
defined, at which the MS and the BTS are required to reach a certain level of performance.
For GSM voice service, for instance, we have seen that GSM900 small MSs (see definition in Section 1.5.6.1)
are required to reach a given BER, FER, and RBER, for an input signal level (ISL) of -102 dBm. The
performances (BER, FER, RBER) are different depending upon the channel profile (static, TU50, RA250, HT100),
but the level is -102 dBm for all profiles.
The performance to be met in GPRS is the block error rate (BLER), referring to all erroneously decoded data
blocks including any headers, SFs, data, and parity bits. Once a radio block, comprising four bursts, is
received on a PDTCH, the mobile performs a de-interleaving and a decoding of the convolutional code, for
coding schemes CS-1 to CS-3 (no convolutional code is used for the coding scheme CS-4). The parity bits
from the block code are then calculated, based on the received bits. If the calculated parity sequence is
different from the received sequence, the block is declared erroneous. The ratio of these erroneous blocks to
the number of received blocks is therefore an estimation of the BLER. The BLER is also defined for the USF and
it refers to the ratio of erroneously decoded USF words over the number of received blocks.
The principle of the sensitivity performance definition is somewhat different in GPRS than in GSM circuit, in the
sense that the BLER level to be reached for the MS and the BTS is not dependent on the channel profile.
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
4/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
Static TU50 (No FH) TU50 (Ideal FH) RA250 (No FH) HT100 (No FH)
PDTCH/CS-1 (dBm)
-104
-104
-104
-104
-103
PDTCH/CS-2 (dBm)
-104
-100
-101
-101
-99
PDTCH/CS-3 (dBm)
-104
-98
-99
-98
-96
PDTCH/CS-4(dBm)
-101
-90
-90
USF/CS-1 (dBm)
-104
-101
-103
-103
-101
-103
-104
-104
-104
-104
-104
-103
-103
-104
-104
-103
-103
-104
No requirement
Note that the specification for PDTCH/CS-1 applies also for PACCH, PBCCH, PAGCH, PPCH, and PTCCH/D.
To avoid the blinding of the receiver, the sensitivity specification is not required if the received level on either
the time slot immediately before or immediately after a received time slot is greater than the desired time slot
level by more than 50 dB for the BTS, or 20 dB for the MS. Also, for the MS, these specifications are not to be
fulfilled if the received level on any of the time slots belonging to the multislot configuration is greater than
the desired (that is the one on which the BLER is actually measured) time slot level by more than 6 dB.
4.2.3.2 Interference Performance
The same BLER performance (10% for PDTCH, 15% for PRACH, and 1% for the USF) is required when
interference is added to the wanted signal. The interference specifications are defined for a desired signal
input level depending on the channel profile, and for a random, continuous, GMSK-modulated interfering signal.
For a BTS, the ISL is -93 dBm + C/Ic, where C/Ic is the cochannel interference ratio, given in Table 4.10 for
the example of GSM-900 and GSM-850. The BLER performance is to be met for the three following cases:
Cochannel interferer-the interfering signal is on the same RF channel as that desired (same ARFCN). The
carrier to interference ratio is referred to as C/Ic.
First adjacent channel-the interfering carrier is 200 kHz away from the desired signal RF channel. The
carrier to interference is given by C/Ia1 = C/Ic - 18 dB.
Second adjacent channel-the interference signal is transmitted at 400 kHz from the desired carrier. The
carrier to interference ratio is C/Ia2 = C/Ic - 50 dB
Table 4.10: C/I Ratio for Cochannel Performance for Normal BTS
GSM-900 and GSM-850 Normal BTS
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
5/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
Propagation Conditions
Type of Channel
TU3 (No FH) TU3 (Ideal FH) TU50 (No FH) TU50 (Ideal FH) RA250 (No FH)
PDTCH/CS-1 (dB)
13
10
PDTCH/CS-2 (dB)
15
13
14
13
13
PDTCH/CS-3 (dB)
16
15
16
15
16
PDTCH/CS-4(dB)
21
23
24
24
No requirement
USF/CS-1 (dB)
19
10
12
10
10
USF/CS-2 to 4 (dB) 18
10
10
If we take the example of CS-4 in GSM900, with the TU50/no FH propagation profile, we have the following
conditions for a normal BTS:
The desired ISL is -93 + C/Ic with C/Ic = 24 dB, so ISL = -69 dBm, for the cochannel, first adjacent, and
second adjacent specifications.
To fulfill the cochannel interference performance, the C/Ic is fixed to 24 dB, so the BLER performance is to
be met for a signal level of -69 dBm, and a cochannel level of -93 dBm.
In the first adjacent channel interference performance case, the wanted signal level is also equal to -69
dBm, and since C/Ial = C/Ic - 18 dB = 24 - 18 = 6 dB, the interferer level is -69 - 6 = -75 dBm.
For the second adjacent channel interference specification, the wanted signal level is still equal to -69
dBm, with C/Ia2 = C/Ic - 50 dB = 24 - 50 = -26 dB, so the interferer level is equal to -69 - (-26) = -43
dBm.
For the MS, the C/I requirements are the same as for the BTS, but the ISL of the desired carrier for which the
performance will be met is higher (by 0, 2, or 4 dB according to the type of MS).
4.2.3.3 Blocking Characteristics
A blocking is an interfering signal at a high power level as compared with the desired signal, either in-band
(which means situated in the receiver band), or out-of-band (out from the receiver band). Of course, the
frequency bands corresponding to the in-band and out-of-band parts are dependent on the system (GSM900, DCS-1800, and PCS-1900).
The blocking characteristics of the receiver refer to its capability of achieving a certain performance in the
presence of a strong interferer in the in-band or one of the out-of-band frequency bands (see Table 4.11).
This requirement exists in the case of the GSM circuit-switched service, and has also been defined for the
GPRS system, from Release 99. No blocking characteristics were defined in Release 97/98 GPRS equipment.
Table 4.11: In-Band and Out-of-Band Definitions for the
Blocking Characteristics
Frequency Band MS
BTS
In band
915-980
860-925
Out-of-band (a)
0.1 to 915 MH
Out-of-band (b)
If we take the example of GSM900, this requirement states that the sensitivity reference level performance
(BLER requirements) will be met in the conditions here:
A desired signal at frequency f 0, with a power level 3 dB higher than in the sensitivity requirement (see
Section 4.2.3.1);
A continuous sine wave blocking signal at a frequency f, which is an integer multiple of 200 kHz, and with a
power level in dBm as specified in Table 4.12.
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
6/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
Small MS
Other MS
BTS
-38
-26
-33
-16
-33
-23
-16
3 MHz = |f - f 0|
-23
-23
-13
(a)
(b)
In-band
Out-of-band
-49 dBm
-45 dBm
-43 dBm
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
power level as given in Table 4.14. Bursts are transmitted on this carrier, with a time delay between 61 and
86 bit periods relative to the bursts of the desired signal.
BTS (dBm)
GSM-400 -31
-31
GSM-900 -31
-31
GSM-850 -31
-31
-35
-35
The reason for this specification and the problems that arise in the receiver due to this requirement are
discussed in a case study (see Section 4.3.4.2).
ALSO ON ETUTORIALS
What's this?
My Life Scoop
Chevrolet
0 comments
Leave a message...
Best
Com m unity
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
Share
8/9
23/04/2013
RF Physical Layer :: Chapter 4: Radio Interface: Physical Layer :: GPRS for mobile internet :: Mobile devices :: eTutorials.org
C o m m e n t fe e d
Su b s cri b e vi a e m a i l
Back Cover
GPRS for Mobile Internet
Chapter 1: Introduction to the GSM System
Chapter 2: GPRS Services
Chapter 3: Overview of GPRS
Chapter 4: Radio Interface: Physical Layer
PLL
RF Physical Layer
Case Studies
References
Selected Bibliography
Chapter 5: Radio Interface: RLC/MAC Layer
Chapter 6: Gb Interface
Chapter 7: Signaling Plane
Chapter 8: User Plane
List of Acronyms
List of Figures
List of Tables
13
Remember the name: eTutorials.org
Advertise on eTutorials.org
Copyright eTutorials.org 2008-2013. All rights reserved.
etutorials.org/Mobile+devices/gprs+mobile+internet/Chapter+4+Radio+Interface+Physical+Layer/RF+Physical+Layer/
9/9