Escolar Documentos
Profissional Documentos
Cultura Documentos
Technical Instructions
CORPORATE
LOS ANGELES, USA
US 1 800 394.9900
Intl +1 818 837.8100
FAX 1 800 394.9910
Intl +1 818 838.7047
Acetone
Soft Lint-Free Cloth
Distilled Water
Cotton Swab
Supplies
Tools
Phillips Screwdriver
Small Flat-Blade Screwdriver
Needlenose Pliers
Alcohol
Toner and Drum
ATLANTA, USA
US 1 877 676.4223
Intl +1 770 516.9488
FAX 1 877 337.7976
Intl +1 770 516.7794
Photo 1
Step 1
Remove the two white tabs from the front
of the doctor bar. (See Photo 1)
DALLAS, USA
US 1 877 499.4989
Intl +1 972 840.4989
FAX 1 877 774.1750
Intl +1 972 840.1750
MIAMI, USA
US 1 800 595.429
Intl +1 305 594.3396
FAX 1 800 522.8640
Intl +1 305 594.3309
Photo 2
Step 2
US 1 800 431.7884
Intl +1 631 345.0121
FAX 1 800 431.8812
Intl +1 631345.0690
SANFORD,USA
US 1 800 786.9049
Intl +1 919 775.4584
FAX 1 800 786.9049
Intl +1 919 775.4584
TORONTO, CAN
CAN 1 877 848.0818
Intl +1 905 712.9501
FAX 1 877 772.6773
Intl +1 905 712.9502
Photo 3
Step 3
Remove the cartridge drive gear from the
end of the cartridge.
MELBOURNE, AUS
AUS 1 800 003. 100
Intl +62 03 9561.8102
FAX 1 800 004.302
Intl +62 03 9561-7751
SYDNEY, AUS
AUS 1 800 003.100
Intl +62 02 9648.2630
FAX 1800 004.302
Intl +62 02 9548.2635
Photo 4
MONTEVIDEO,URY
Step 4
Remove the idler gear from the side of
the cartridge. (See Photo 4)
URY 02 902.7206
Intl +5982 900.8358
FAX +5982 908.3816
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
Step 7
Rotate the cartridge 180. Remove the
developer roller contact from the side of
the cartridge. (See Photos 7)
Step 5
Remove the E clip that holds
the developer roller drive gear.
(See Photo 5)
Photo 5
Photo 8
Step 8
Rotate the developer roller contact bushing from its starting position (See Photo 8)
up (counter clock-wise) toward the top of
the cartridge.
(See Photo 9)
Step 6
Using a small flat-blade screwdriver, lift up the locking clip that
holds the drive gear to the
developer roller axle. Remove
the gear. (See Photos 6)
Photo 9
Photo 6
Photo 10
Step 9
Slide the contact bushing off the developer
roller axle.
(See Photo 10)
Photo 11
Step 10
While holding the shaft of the developer
roller, lift the roller out from the hopper
and slide the developer roller axle out from
the toner hopper end plate.
(See Photo 11)
Photo 12
Step 11
To clean the developer roller, take a lintfree cloth, add a small amount of alcohol
and soak the cloth in distilled water. Place
the developer roller axle into a drill. Clean
the developer roller using the lint-free
cloth while the roller is rotating in the
drill. (See Photo 12)
Photo 13
Photo 17
Step 13
Remove the toner from the doctor
bar using compressed air or a vacuum.
Clean the contact edge of the bar using a
cotton swab and Acetone.
(See Photo 14)
Photo 15
Step 12
Slide the doctor bar down toward the
developer roller opening and remove the
bar.
(See Photo 13)
Photo 14
Step 16
Photo 18
Step 14
Remove the cartridge warranty sticker
from the side of the cartridge.
(See Photo 15)
Photo 16
Step 15
Remove the toner hopper fill cap from
the end of the cartridge. (See Photo 16)
Carefully clean the hopper using dry
compressed air or a vacuum. Do not
damage the developer roller sealing
blade that sits under the developer roller.
Notes
Step 19
Slide the developer roller contact onto
the end of the hopper.
(See Photo 21)
Step 17
Install the keyed end of the
developer roller axle into the
toner hopper end plate and
lower the developer roller into
place. (See Photo 19)
Photo 22
Step 20
Rotate the hopper 180 and install the
developer roller drive gear onto the axle
of the roller. Place the E clip onto the axle
to hold the drive gear in place.
(See Photo 22)
Photo 19
Photo 23
Step 21
Install the idler gear onto the end of the
cartridge. (See Photo 23)
Step 18
Install the contact bushing onto
the developer roller axle. Rotate
the bushing clock-wise to lock
the bushing into place.
(See Photo 20)
Photo 24
Step 22
Install the cartridge drive gear onto the
end of the cartridge.
(See Photo 24)
Photo 20
Photo 25
Step 23
Place the doctor bar tension spring onto
the top of the doctor bar so the arrow is
facing away from the hopper. Place the
white tabs onto the doctor blade next to
each end of the tension spring.
(See Photo 25)
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
Step 24
Fill the hopper with toner and install the
fill plug.
Step 3
Step 25
Replace the chip found on the bottom of
the cartridge. (See Photo 26)
Step 26
Test the cartridge.
Photo 30
Step 1
Step 1: Remove the two screws (one on
each end of the cartridge) that hold the
toner hopper locking mechanism.
(See Photos 27 & 28)
Photo 28
Step 4
Slide the drum axle out of the
waste hopper from the drive
gear side.
(See Photo 31)
Photo 31
Photo 29
Step 2
Step 2: Remove the locking mechanism.
(See Photo 29)
Step 7
Remove the two screws holding the wiper
blade.
(See Photo 34)
Step 5
Remove the drum. (See Photo 32)
If you plan on reusing the drum,
clean the drum with a soft lintfree cloth and place the drum in
a protected area out of the light.
Photo 35
Step 8
Remove the wiper blade. (See Photo 35)
Clean the waste hopper and wiper blade
using dry compressed air or a vacuum.
Photo 32
Photo 36
Step 9
Apply padding powder to the wiper
blade. Place the blade into the waste hopper and install the two screws that hold
the blade in place. (See Photo 36)
Step 6
Grasp the PCR contact saddles
and lift the PCR from the waste
hopper. (See Photo 33) Clean the
PCR using a dry lint-free cloth.
Photo 37
Step 10
Clean the PCR saddles using a cotton
swab and alcohol. Place the saddles onto
the ends of the PCR and place the PCR
back into the waste hopper.
(See Photo 37)
Photo 33
Photo 38
Step 11
Place the waste hopper so that it is facing
towards you. Apply padding powder to
the drum and place the drum in the hopper so the drive gear is on the left side of
the cartridge.
(See Photo 38)
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
Step 12
Slide the drum axle into the drum starting
on the drive gear side. See Photo # 39.
Photo 40
Step 13
Install the E clip onto the small gear side
of the drum axle. See Photo # 40.
Photo 41
Step 14
Install the toner hopper locking mechanism onto the waste hopper. Install the
two screws that hold the bar in place. See
Photo # 41.
Step 15
Test the waste hopper.
Notes
IBM:
1412, 1412n Toner Cartridge
1412, 1412n High Yield Toner Cartridge
1412, 1412n IBM Return Program
Dell 1700
Dell 1700n
IBM 1412
IBM 1412n
Machine Supplies:
Lexmark
E330, E332 High Yield Return Program
E230, E232, E330, E332 Return Program
E330, E323 High Yield Cartridge
E230, E232, E330, E332 Toner Cartridge
E230, E232, E330, E332 Drum Unit
75P5708
75P5710
75P5709
75P5711
75P5712
310-5399
310-5400
310-5401
310-5402
310-5404
has the same print speed of the 1700 and sells for $299.
IBM released two machines using this new Lexmark engine
as well. The 1412 is based on the E330 engine that prints
27ppm and, at $399, sells for the same price.The 1412n is IBMs
network version of the Lexmark E332n printer and, at $499, is
priced the same.
Standard yield cartridges and high yield cartridges are
available from all suppliers. However Dell offers a 3,000 page
standard yield cartridge while Lexmark and IBM standard
yield cartridge yields 2,500 pages at 5% coverage.
All three suppliers offer a 6,000 page high yield cartridge
and all cartridges are available in Lexmarks Cartridge Return
program. The drum units for these machines yield 30,000
pages and, according to Lexmark, many customers may not
ever need to replace the drum unit because of low monthly
usage.
Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment.
None of FG's products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.