Escolar Documentos
Profissional Documentos
Cultura Documentos
INTRODUCTION
The Mechanical working of metal is defined as the plastic deformation of metals under the action of
externally applied forces. The mechanical working of metals is described as hot working and cold working
depending upon whether the metal is worked above or below the recrystallization temperature.
The metal is subjected to mechanical working for the following purpose:
Hot Working
The working of metals above the recrystallization temperature is called hot working. Recrystallization
temperature is the temperature at which new grains are formed in the metal. Hot working of the metals has
following advantages and disadvantages.
Advantages:1.
2.
3.
4.
The porosity of metal is largely eliminated, thus producing strong and uniform structure.
The grain structure of the metal is refined.
The impurities like slag are squeezed into fibres and are uniformly distributed throughout the metal.
Mechanical properties are improved.
Cold working
The working of metals below their recrystallization temperature is known as cold working. Most of cold
working processes are performed at room temperature. The cold working distorts the grain structure and
does not provide an appreciable reduction in size. The extent to which a metal can be cold worked depends
upon its ductility. The higher the ductility of the metal, the more it can be cold worked. During cold working
severe stresses known as residual stresses are set up. These stresses are undesirable therefore a suitable heat
treatment process may be employed to relieve these stresses.
Effects of cold working
The stresses are set up in the metal which remains in the metal, unless they are removed by subsequent heat
treatment.
A distortion of the grain structure is created.
The strength and hardness of the metal are increased with a corresponding loss in ductility.
The recrystalline temperature for steel is increased.
Cold working process
1. Cold rolling
2. Cold forging
3. Cold spinning
4. Cold extrusion
5. Cold drawing
6. Cold bending
Rolling
Rolling is one of the most important industrial metal forming operations. Rolling is the plastic deformation
of materials caused by compressive force applied through a set of rolls. The cross section of the work piece
is reduced by the process. The material gets squeezed between a pair of rolls, as a result of which the
thickness gets reduced and the length gets increased. Mostly, rolling is done at high temperature, called hot
rolling because of requirement of large deformations. Hot rolling results in residual stress-free product.
However, scaling is a major problem, due to which dimensional accuracy is not maintained. Cold rolling of
sheets, foils etc are gaining importance, due to high accuracy and lack of oxide scaling. Cold rolling also
strengthens the product due to work hardening.
Rolling Principle:
Hot Rolling
The hot rolling is the most rapid method of converting large sections into desired shapes. The forming of
bars, plates, sheets, rails, angles, I-beams and other structural sections are made by hot Rolling.
The operation consists of passing the hot ingot through at least two rolls rotating in opposite directions at the
same speed. The rolls squeeze the passing ingot to reduce its cross-section and increase its length. The first
operation to the ingot is carried out at blooming mill where it is rolled to blooms. The blooms are cut up in
lengths for subsequent reducing process into billets.
The materials commonly hot rolled are aluminium, copper, magnesium, their alloys and many grades of
steel.
Rolling mills:
Two-High Rolling Mills
A two-high rolling mill as shown in fig. has two horizontal rolls revolving at the same speed but in opposite
direction. The rolls are supported on bearings housed in sturdy upright side frames called stands. The space
between the rolls can be adjusted by raising or 1owering the upper roll. Their direction of rotation is fixed
and cannot be reversed. The reduction in the thickness of work is achieved by feeding from one direction
only.
Cluster Mill
It is a special type of four-high rolling mill in which each of the two smaller working rolls are backed up by
two or more of the larger back-up rolls as shown in Fig. For rolling hard thin materials, it may be necessary
to employ work rolls of very small diameter but of considerable length. In such cases adequate support of
the working rolls can be obtained by using a cluster-mill. This type of mill is generally used for cold rolling
work.