Escolar Documentos
Profissional Documentos
Cultura Documentos
1 Cluster-Mode
Description
This article describes the steps to be performed to setup FCP in Data ONTAP 8.1 Cluster-Mode.
Procedure
Perform the following steps:
1.Check your FC hardware; we are using the 0c onboard ports of four nodes:
cluster1::*> system node run -node * fcadmin config 4 entries were acted on.
Node: cluster1-01
Local Adapter Type
State
Status--------------------------------------------------- 0a
CONFIGURED.
online
0b
initiator CONFIGURED.
0c
target
CONFIGURED
online
0d
initiator
CONFIGURED.
online
initiator
online
Node: cluster1-02
Local Adapter Type
State
Status--------------------------------------------------- 0a
CONFIGURED.
online
0b
initiator CONFIGURED.
0c
target
CONFIGURED
online
0d
initiator
CONFIGURED.
online
initiator
online
Node: cluster1-03
Local Adapter Type
State
Status--------------------------------------------------- 0a
CONFIGURED.
online
0b
initiator CONFIGURED.
0c
target
CONFIGURED
online
0d
initiator
CONFIGURED.
offline
Node: cluster1-04
initiator
online
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 1 of 11
8/20/2015
initiator
online
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 2 of 11
8/20/2015
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 3 of 11
Port
Port WWPN
State
Type
Attached WWPN
Port
ID----------------------------------------------------------------------------------0
20:00:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:86:57:d5:58
0x810000 1
20:01:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:83:96:57:d5:58 0x810100 2
20:02:00:05:1e:03:a4:6e Online
FPort
50:0a:09:81:95:44:8b:86 0x810200 3
20:03:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:85:44:8b:86 0x810300 4
20:04:00:05:1e:03:a4:6e
Online
F-Port
50:0a:09:81:97:f9:43:7b 0x810400 5
20:05:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:f9:43:7b 0x810500
6
20:06:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:87:f9:43:7b
0x810600 7
20:07:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:97:f9:43:7b 0x810700 8
20:08:00:05:1e:03:a4:6e Offline
none
-9
20:09:00:05:1e:03:a4:6e Offline
none
-10
20:0a:00:05:1e:03:a4:6e Online
F-Port
10:00:00:00:c9:39:a6:1a 0x810a00 11
20:0b:00:05:1e:03:a4:6e
Online
F-Port
21:00:00:e0:8b:12:fe:5e 0x810b00 12
20:0c:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:f9:71:c0 0x810c00
13
20:0d:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:39:75:f8
0x810d00 14
20:0e:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:e9:3d:38 0x810e00 15
20:0f:00:05:1e:03:a4:6e
Port
50:0a:09:81:87:99:37:9d 0x810f00
8/20/2015
Online
F-
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 4 of 11
DOT is plugged into 12/13/14/15. Note they are just F-ports at this point, since we do not have a
FCP Vserver started yet.
Vserver pod2vs9 with language set to C created.
Do you want to create a data volume? {yes, no} [yes]: Enter the volume name
[vol1]: pod2vs9_vol01 Enter the name of the aggregate to contain this volume
{aggr1_c01n01, aggr1_c01n02, aggr1_c01n03, aggr1_c01n04} [aggr1_c01n04]: Enter the
volume size: 100g Enter the volume junction path [/vol/pod2vs9_vol01]: It can take
up to a minute to create a volume...
Volume pod2vs9_vol01 of size 100GB created on aggregate aggr1_c01n04 successfully.
Do you want to create an additional data volume? {yes, no} [no]:
Do you want to create a logical interface? {yes, no} [yes]: Enter the LIF name
[lif1]: pod2vs9_fc1 Enter the home node {cluster1-01, cluster1-02, cluster1-03,
cluster1-04} [cluster1-04]: cluster1-01 Enter the home port [0c]: FCP lif
pod2vs9_fc1 configured on Vserver pod2vs9
8/20/2015
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 5 of 11
Enter the home node {cluster1-01, cluster1-02, cluster1-03, cluster1-04}
[cluster1-04]: cluster1-02 Enter the home port [0c]: FCP lif pod2vs9_fc2
configured on Vserver pod2vs9 Do you want to create an additional LIF now? {yes,
no} [no]: yes Enter the LIF name [lif3]: pod2vs9_fc3 Enter the home node {cluster101, cluster1-02, cluster1-03, cluster1-04} [cluster1-02]: cluster1-03 Enter the
home port [0c]: FCP lif pod2vs9_fc3 configured on Vserver pod2vs9 Do you want to
create an additional LIF now? {yes, no} [no]: yes Enter the LIF name [lif4]:
pod2vs9_fc4 Enter the home node {cluster1-01, cluster1-02, cluster1-03, cluster104} [cluster1-01]: cluster1-04 Enter the home port [0c]: FCP lif pod2vs9_fc4
configured on Vserver pod2vs9 Do you want to create an additional LIF now? {yes,
no} [no]:
8/20/2015
Status Vserver
Target
Admin---------- ---------------------------20:04:00:a0:98:0a:b7:0b
up
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 6 of 11
cluster1::*> lun map -path /vol/pod2vs9_vol01/lun0 -lun-id 0 -igroup sdt_win_real2
8/20/2015
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 7 of 11
Port
Port WWPN
State
Type
Attached WWPN
Port
ID----------------------------------------------------------------------------------0
20:00:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:86:57:d5:58
0x810000 1
20:01:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:83:96:57:d5:58 0x810100 2
20:02:00:05:1e:03:a4:6e Online
FPort
50:0a:09:81:95:44:8b:86 0x810200 3
20:03:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:85:44:8b:86 0x810300 4
20:04:00:05:1e:03:a4:6e
Online
F-Port
50:0a:09:81:97:f9:43:7b 0x810400 5
20:05:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:f9:43:7b 0x810500
6
20:06:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:87:f9:43:7b
0x810600 7
20:07:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:82:97:f9:43:7b 0x810700 8
20:08:00:05:1e:03:a4:6e Offline
none
-9
20:09:00:05:1e:03:a4:6e Offline
none
-10
20:0a:00:05:1e:03:a4:6e Online
F-Port
10:00:00:00:c9:39:a6:1a 0x810a00 11
20:0b:00:05:1e:03:a4:6e
Online
F-Port
21:00:00:e0:8b:12:fe:5e 0x810b00 12
20:0c:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:f9:71:c0 0x810c00
20:01:00:a0:98:0a:b7:0b
0x810c01 13
20:0d:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:39:75:f8 0x810d00
20:00:00:a0:98:0a:b7:0b
0x810d01 14
20:0e:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:e9:3d:38 0x810e00
20:03:00:a0:98:0a:b7:0b
0x810e01 15
20:0f:00:05:1e:03:a4:6e Online
F-Port
50:0a:09:81:87:99:37:9d 0x810f00
20:02:00:a0:98:0a:b7:0b
0x810f01
8/20/2015
5
Link_failure:
1
Loss_of_sync: 1
Loss_of_sig: 2 Proc_rqrd:
0
Invalid_word: 0
0 Tx_unavail:
0
Address_err: 0 Overrun:
0
Lr_out:
0
0 2_parity_err:
0
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 8 of 11
Authentication: None portDisableReason: None portCFlags: 0x1 portFlags:
0x20b03
PRESENT ACTIVE F_PORT G_PORT U_PORT NPIV LOGICAL_ONLINE LOGIN NOELP
ACCEPT FLOGI portType: 11.0 POD Port: Port is licensed portState: 1
Online
portPhys: 6
In_Sync portScn:
32
F_Port port generation number:
0
portId:
810f00 portIfId:
4302000f portWwn:
20:0f:00:05:1e:03:a4:6e portWwn
of device(s) connected: 20:02:00:a0:98:0a:b7:0b
50:0a:09:81:87:99:37:9d
Distance: normal portSpeed: N4Gbps
8/20/2015
20:02:00:a0:98:0a:b7:0b
10:00:00:00:c9:39:a6:1a
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 9 of 11
9.On Windows 2008 host, enable MPIO for the LUN type. Run the MPIO Properties and enable it
for the NetApp LUN C-mode (Click the SPC-3 compliant NETAPP LUN C-Mode entry, an then
click Add):
10.After a reboot, the following is displayed, showing that the NetApp LUN C-Mode will be
managed by MPIO:
8/20/2015
11.Format the disk, mount as drive, etc, using Windows tooling (by using disk management).
12.Start some workload on the host:
E:\>sio_ntap_win32.exe 50 50 64k 5g 6000 16 img.iso Version: 3.00
https://kb.netapp.com/support/index?page=content&id=1013341&pmv=print&impressions...
Page 10 of 11
cluster1::*> statistics show -node * -object volume -instance *pod2vs9* -counter
read_data|write_data
cluster1::*> vol move start -volume pod2vs9_vol01 -destination-aggregate
aggr1_c01n02 -foreground true
(volume move start) [Job 348] Job is queued: Move
"pod2vs9_vol01" in Vserver "pod2vs9" to aggregate "aggr1_c01n02". Use the "job
show i [Job 349] Transferring data: 12.61GB sent. [Job 349] Transferring data:
14.35GB sent. [Job 349] Transferring data: 15.54GB sent. [Job 349] Transferring
data: 17.39GB sent. [Job 349] Transferring data: 18.22GB sent. [Job 349]
Transferring data: 19.03GB sent. [Job 348] Cutover Deferred(20.11GB Sent)::Reason:
The estimated time to complete cutover is greater than the cutover that can be
tolerated [Job 348] Job succeeded: Successful
8/20/2015
https://kb.netapp.com/support/index?page=content&