Escolar Documentos
Profissional Documentos
Cultura Documentos
IN+ 1 10 IN −
IN+ 1 14 IN−
GAIN ADJ 2A 2 9 GAIN ADJ 2B
NC 2 13 NC
GAIN ADJ 1A 3 8 GAIN ADJ 1B
GAIN ADJ 2A 3 12 GAIN ADJ 2B
VCC − 4 7 VCC+
GAIN ADJ 1A 4 11 GAIN ADJ 1B
OUT+ 5 6 OUT−
VCC− 5 10 VCC+
NC 6 9 NC
OUT+ 7 8 OUT−
NC No internal connection
description/ordering information
The µA733 is a monolithic two-stage video amplifier with differential inputs and differential outputs. Internal
series-shunt feedback provides wide bandwidth, low phase distortion, and excellent gain stability.
Emitter-follower outputs enable the device to drive capacitive loads, and all stages are current-source biased
to obtain high common-mode and supply-voltage rejection ratios.
Fixed differential amplification of 10 V/ V, 100 V/ V, or 400 V/ V may be selected without external components,
or amplification may be adjusted from 10 V/ V to 400 V/ V by the use of a single external resistor connected
between 1A and 1B. No external frequency-compensating components are required for any gain option.
The device is particularly useful in magnetic-tape or disc-file systems using phase or NRZ encoding and in
high-speed thin-film or plated-wire memories. Other applications include general-purpose video and pulse
amplifiers where wide bandwidth, low phase shift, and excellent gain stability are required.
The µA733C is characterized for operation from 0°C to 70°C; the µA733M is characterized for operation over
the full military temperature range of −55°C to 125°C.
ORDERING INFORMATION
ORDERABLE TOP-SIDE
TA PACKAGE†
PART NUMBER MARKING
P-DIP (N) Tube of 25 UA733CN UA733CN
Tube of 50 UA733CD
0°C to 70°C SOIC (D) UA733C
Reel of 2500 UA733CDR
SOP (NS) Reel of 2000 UA733CNSR UA733
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
!"# $% Copyright 2004, Texas Instruments Incorporated
$ ! ! &
'
$$ ()% $ !* $ #) #$
* ## !%
symbol
GAIN ADJ 1A
GAIN ADJ 2A
IN + + OUT+
_
IN − OUT−
GAIN ADJ 1B
GAIN ADJ 2B
schematic
VCC+
OUT+
IN + IN − 7 kΩ
1A 1B 7 kΩ
GAIN 50 Ω GAIN OUT −
ADJ 50 Ω ADJ
2A 2B
590 Ω 590 Ω
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
mA733C mA733M UNIT
Supply voltage VCC+ (see Note 1) 8 8 V
Supply voltage VCC− (see Note 1) −8 −8 V
Differential input voltage ±5 ±5 V
Common-mode input voltage ±6 ±6 V
Output current 10 10 mA
Continuous total power dissipation See Dissipation Rating Table
D package 86
Package thermal impedance, qJA (see Notes 2 and 3) N package 80 °C/W
C/W
NS package 76
Maximum junction temperature, TJ 150 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds J or U package 300 °C
Storage temperature range, Tstg − 65 to 150 − 65 to 150 °C
† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and
functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions section of
this specification is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltages, are with respect to the midpoint between VCC+ and VCC–.
2. Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) – TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
RS = 50 Ω, 1 7.5 7.5
Propagation
tpd 2 Output voltage 2 6.0 10 6.0 10 ns
delay time
step = 1 V 3 3.6 3.6
RS = 50 Ω, 1 10.5 10.5
tr Rise time 2 Output voltage 2 4.5 12 4.5 10 ns
step = 1 V 3 2.5 2.5
Maximum output
Isink(max) Any 2.5 3.6 2.5 3.6 mA
sink current
No load,
ICC Supply current Any 16 24 16 24 mA
No signal
† The gain option is selected as follows:
Gain Option 1: Gain-adjust pin 1A is connected to pin 1B, and pins 2A and 2B are open.
Gain Option 2: Gain-adjust pin 1A and pin 1B are open, pin 2A is connected to pin 2B.
Gain Option 3: All four gain-adjust pins are open.
electrical characteristics, VCC± = ±6 V, TA = 0°C to 70°C for mA733C, − 55°C to 125°C for mA733M
GAIN mA733C mA733M
PARAMETER FIGURE TEST CONDITIONS UNIT
OPTION† MIN MAX MIN MAX
1 250 600 200 600
Large-signal differential
AVD 1 VOD = 1 V 2 80 120 80 120 V/ V
voltage amplification
3 8 12 8 12
IIO Input offset current Any 6 5 µA
IIB Input bias current Any 40 40 µA
Common-mode input
VICR 1 Any ±1 ±1 V
voltage range
1 1.5 1.5
VOO Output offset voltage 1 V
2&3 1.5 1.2
Maximum peak-to-peak
VOPP 1 Any 2.8 2.5 V
output voltage swing
ri Input resistance 3 VOD ≤ 1 V 2 8 8 kΩ
Common-mode rejection VIC = +1 V,
CMRR 4 2 50 50 dB
ratio f ≤ 100 kHz
Supply voltage rejection
kSVR 1 ∆VCC± = ± 0.5 V 2 50 50 dB
ratio (∆VCC /(∆VIO)
Maximum output sink
Isink(max) Any 2.5 2.2 mA
current
No load,
ICC Supply current Any 27 27 mA
No signal
† The gain option is selected as follows:
Gain Option 1: Gain-adjust pin 1A is connected to pin 1B, and pins 2A and 2B are open.
Gain Option 2: Gain-adjust pin 1A and pin 1B are open, pin 2A is connected to pin 2B.
Gain Option 3: All four gain-adjust pins are open.
test circuits
0.2 µF
+ +
VID VOD 2 kΩ VID 0.2 µF
− −
50 Ω 50 Ω 50 Ω 50 Ω 1 kΩ 1 kΩ
Figure 1 Figure 2
0.2 µF
50 Ω
+
+
VOD 2 kΩ 50 Ω 0.2 µF
−
−
VIC
1 kΩ 1 kΩ
Figure 3 Figure 4
2B 1B
0.2 µF
+
0.2 µF
+ −
VOD 2 kΩ
−
50 Ω 50 Ω 1 kΩ 1 kΩ
Radj
2A 1A
Figure 5 Figure 6
TYPICAL CHARACTERISTICS
PHASE SHIFT
PHASE SHIFT
vs
vs
FREQUENCY
FREQUENCY
5
50
VCC ± = ± 6 V
VCC ± = ± 6 V
TA = 25°C 0 TA = 25°C
0
− 50
GAIN 2
Phase Shift − Degrees
−300
−15
−350
−400
−20
0 1 2 3 4 5 6 7 8 9 10 −450
1 4 10 40 100 400
f − Frequency − MHz
f − Frequency − MHz
Figure 7 Figure 8
VOLTAGE AMPLIFICATION
VOLTAGE AMPLIFICATION
(SINGLE-ENDED OR DIFFERENTIAL)
(SINGLE-ENDED OR DIFFERENTIAL)
vs
vs
TEMPERATURE
SUPPLY VOLTAGE
Voltage Amplification Relative to Value at VCC +_ = +_ 6 V
Voltage Amplification Relative to Value at TA = 25o C
1.2
1.4
VCC ± = ± 6 V TA = 25°C
GAIN 1
1.2
1.1
mA733C
1.0 GAIN 3
GAIN 2 GAIN 3
1.0
GAIN 2 0.8
GAIN 3 GAIN 2
0.9
0.6
GAIN 1
GAIN 1
0.8
−75 − 50 − 25 0 25 50 75 100 125 0.4
3 4 5 6 7 8
TA − Free-Air Temperature − °C
|VCC±| − Supply Voltage − V
Figure 9 Figure 10
TYPICAL CHARACTERISTICS
400 TA = 25°C 40
See Figure 6
GAIN 2
200
30
100
70
20
GAIN 3
40
10
20 VCC ± = ± 6 V
TA = 25°C
10 0
10 40 100 400 1k 4k 10 k 1 4 10 40 100 400
Radj − Resistance Between G1A and G1B − Ω f − Frequency − MHz
Figure 11 Figure 12
SUPPLY CURRENT
SUPPLY CURRENT
vs
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
20
24
No Load
18
No Signal
16 20 TA = 25°C
I CC − Supply Current − mA
I CC − Supply Current − mA
14
mA733C 16
12
10
12
8
6 8
4 VCC ± = ± 6 V
No Load 4
2 No Signal
0
−75 − 50 − 25 0 25 50 75 100 125 0
3 4 5 6 7 8
TA − Free-Air Temperature − °C
|VCC±| − Supply Voltage − V
Figure 13 Figure 14
TYPICAL CHARACTERISTICS
5
3
2
3
2
1
1
0 0
10 40 100 400 1k 4k 10 k 3 4 5 6 7 8
RL − Load Resistance − Ω |VCC±| − Supply Voltage − V
Figure 15 Figure 16
40
VCC ± = ± 6 V
TA = 25°C VCC ± = ± 6 V
35
5
30
r i − Input Resistance − kΩ
4
25
GAIN 2
3
20
mA733C
2 15
10
1
5
0
1 2 4 7 10 20 40 70 100 200 400 0
− 60 − 40 −20 0 20 40 60 80 100 120 140
f − Frequency − MHz
TA − Free-Air Temperature − °C
Figure 17 Figure 18
0.008 (0,20)
0.080 (2,03) 0.004 (0,10)
0.050 (1,27)
0.019 (0,48)
1 10
0.015 (0,38)
0.050 (1,27)
0.280 (7,11)
0.230 (5,84)
5 6
4 Places
0.005 (0,13) MIN
0.350 (8,89) 0.350 (8,89)
0.250 (6,35) 0.250 (6,35)
4040179 / B 03/95
NO. OF A B
18 17 16 15 14 13 12
TERMINALS
** MIN MAX MIN MAX
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
4040140 / D 10/96
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless