Escolar Documentos
Profissional Documentos
Cultura Documentos
electromaniacs.com community
You are free to distribute this file to other persons
who needs it , but without of charge
Also on http://electromaniacs.com you can find
thousands of service manuals , schematics free of
charge
SM003
MODEL NAMES
32PD3000E
42PD3000E
SERVICE MANUAL
MANUEL D'ENTRETIEN
WARTUNGSHANDBUCH
CAUTION:
Before servicing this chassis, it is important that the service technician read the Safety
Precautions and Product Safety Notices in this service manual.
ATTENTION:
Avant deffectuer lentretien du chassis, le technicien doit lire les Prcautions de scurit
et les Notices de scurit du produit prsents dans le prsent manuel.
VORSICHT:
Vor ffnen des Gehuses hat der Service-Ingenieur die Sicherheitshinweise und Hinweise
zur Produktsicherheit in diesem Wartungshandbuch zu lesen.
Plasma TV
October 2002
32PD3000 / 42PD3000
Safety
ENGLISH
SAFETY PRECAUTIONS
WARNING: The following precautions must be
observed.
ALL PRODUCTS
Before any service is performed on the chassis an
isolation transformer should be inserted between
the power line and the product.
1. When replacing the chassis in the cabinet,
ensure all the protective devices are put back in
place.
2. When service is required, observe the original
lead dressing. Extra precaution should be taken to
ensure correct lead dressing in any high voltage
circuitry area.
3. Many electrical and mechanical parts in
HITACHI products have special safety related
characteristics. These characteristics are often not
evident from visual inspection, nor can the
protection afforded by them necessarily be
obtained by using replacement components rated
for higher voltage, wattage, etc. Replacement parts
which have these special safety characteristics are
identified by marking with a ! on the schematics
and the replacement parts list. The use of a
substitute replacement component that does not
have the same safety characteristics as the
HITACHI recommended replacement one, shown
in the parts list, may create electrical shock, fire, Xradiation, or other hazards.
4. Always replace original spacers and maintain
lead lengths. Furthermore, where a short circuit has
occurred, replace those components that indicate
evidence of overheating.
5. Insulation resistance should not be less than 2M
ohms at 500V DC between the main poles and any
accessible metal parts.
6. No flashover or breakdown should occur during
the dielectric strength test, applying 3kV AC or
4.25kV DC for two seconds between the main
poles and accessible metal parts.
7. Before returning a serviced product to the
customer, the service technician must thoroughly
test the unit to be certain that it is completely safe
to operate without danger of electrical shock. The
service technician must make sure that no
protective device built into the instrument by the
manufacturer has become defective, or
inadvertently damaged during servicing.
CE MARK
1. HITACHI products may contain the CE mark on
the rating plate indicating that the product contains
parts that have been specifically approved to
provide electromagnetic compatibility to designated
levels.
2. When replacing any part in this product, please
use only the correct part itemised in the parts list to
ensure this standard is maintained, and take care
to replace lead dressing to its original state, as this
can have a bearing on the electromagnetic
radiation/immunity.
PICTURE TUBE
1. The line output stage can develop voltages in
excess of 25kV; if the E.H.T. cap is required to be
removed, discharge the anode to chassis via a high
value resistor, prior to its removal from the picture
tube.
2. High voltage should always be kept at the rated
value of the chassis and no higher. Operating at
higher voltages may cause a failure of the picture
tube or high voltage supply, and also, under certain
circumstances could produce X-radiation levels
moderately in excess of design levels. The high
voltage must not, under any circumstances, exceed
29kV on the chassis (except for projection
Televisions).
3. The primary source of X-radiation in the product
is the picture tube. The picture tube utilised for the
above mentioned function in this chassis is
specially constructed to limit X-radiation. For
continued X-radiation protection, replace tube with
the same type as the original HITACHI approved
type
4. Keep the picture tube away from the body while
handling. Do not install, remove, or handle the
picture tube in any manner unless shatterproof
goggles are worn. People not so equipped should
be kept away while picture tubes are handled
LASERS
If the product contains a laser avoid direct
exposure to the beam when the cover is open or
when interlocks are defeated or have failed.
32PD3000 / 42PD3000
FRANAIS
CONSIGNES DE SECURITE
AVERTISSEMENT: vous devez respecter les
prcautions suivantes
POUR TOUS LES PRODUITS Avant
deffectuer une intervention dentretien sur le
chssis, vous devez insrer un transformateur
disolement entre la ligne dalimentation lectrique
et le produit.
1. Lors de la remontage du chssis dans le coffret,
vrifiez que tous les dispositifs de protection sont
remis en place.
2. Lorsquune intervention dentretien savre
ncessaire, respectez lagencement dorigine des
conducteurs. Vous devez prendre des precautions
supplmentaires pour garantir un agencement
correct des conducteurs dans toutes les zones o
des circuits haute tension sont prsents.
3. De nombreux composants lectriques et
mcaniques des appareils HITACHI ont des
caractristiques spciales de scurit. Bien
souvent, ces caractristiques ne sont pas
videntes lors dun examen visuel et la protection
quils offrent nest pas forcment garantie si vous
utilisez des composants de rechange conus, par
exemple, pour une tension plus leve, une
puissance plus forte. Les pices de rechange qui
offrent des caractristiques spciales de scurit
sont identifies par un reprage comportant le
symbole ! sur les schmas et sur la nomenclature
des pices de rechange. Lemploi dun composant
de rechange qui ne respecte pas les mmes
caractristiques de scurit que la pice de
rechange que recommande HITACHI et qui figure
dans la nomenclature risque de provoquer un choc
lectrique, un incendie, des rayons X ou dautres
dangers.
4. Remettez toujours en place les entretoises
dorigine et respectez la longueur des conduites.
En outre, la suite dun court-circuit, remplacez les
composants prsentant des signes de surchauffe.
5. La rsistance disolement doit tre suprieure ou
gale 2 mga ohms 500 V c.c. entre les poles
principaux et des composants mtalliques
accessibles, quels quils soient.
6. Aucun claquage et aucune rupture ne doit se
produire pendant lessai de rsistance dilectrique
la suite de lapplication dune tension de 3 kV c.a.
ou de 4,35 kV c.c. pendant deux secondes entre
les poles principaux et des composants mtalliques
accessibles.
7. Avant de remettre au client un produit qui a fait
lobjet dun entretien, le technicien qui sest charg
de cette intervention doit tester fond cet
ensemble pour sassurer quil ne prsente aucun
danger oprationnel et aucun risque de choc
lectrique. Ce technicien doit sassurer quaucun
des dispositifs de protection intgrs cet
instrument par le fabricantnest dfectueux ou na
t endommag de faon accidentelle lors de
lentretien. suivantes
LABEL CE
1. Les produits HITACHI peuvent avoir reu le label
CE qui figure sur la plaque signaltique pour
indiquer que cet ensemble contient des
composants qui ont fait lobjet dune homologation
spcifique de respect des normes de compatibilit
lectromagntique en fonction de niveaux bien
spcifis.
2. Lors du remplacement dun des composants de
ce produit, utilisez uniquement le composant
correct identifi dans la nomenclature afin de
maintenir le respect de cette norme ; en outre, vous
devez galement ramener lagencement des
conducteurs son tat dorigine car cela peut avoir
une influence au niveau des rayonnements
lectromagntiques et sur la protection contre ces
rayons.
PICTURE TUBE
1. Ltage de sortie des lignes peut dvelopper des
tensions de plus de 25 kV ; sil faut retirer le
chapeau de protection contre les tensions
extrmement leves, il convient de dcharger
lanode contre le chssis par le biais dune
rsistance de forte valeur avant de dposer ce
chapeau du tube image.
2. La haute tension doit toujours se maintenir la
valeur nominale du chssis et ne pas dpasser
cette dernire. Un fonctionnement des
tempratures leves peut provoquer une
dfaillance du tube image ou lentre dune tension
leve. Dans certains cas, cela peut mme
provoquer des rayons X dun niveau lgrement
suprieur aux valeurs de calcul. Cette haute
tension ne doit en aucun cas dpasser 29 kV sur le
chssis ( lexception des tlviseurs de
projection).
3. La principale source de rayons X de cet appareil
est le tube image. Le tube image employ pour
assurer la fonction susmentionne dans ce chssis
est spcialement construit pour limiter des rayons
X. Pour maintenir cette protection contre les rayons
X, il faut remplacer le tube dorigine dun type agr
par HITACHI par un autre tube de mme type.
4. Lors des manipulations, ne tenez jamais le tube
image contre le corps. Pendant toutes les
operations dinstallation, de dpose et de
manipulation de ce tube image, quelle que soit la
mthode employe, vous devez toujours porter des
lunettes de scurit anti-clatements. Les
personnes qui ne portent pas ce type de lunettes
doivent se tenir lcart du tube image lors de la
manipulation de ce dernier.
RAYONS LASER
Si ce produit contient un rayon laser, vitez toute
exposition directe ce faisceau lors de louverture
du couvercle ou lors de llimination des
verrouillages de scurit ou aprs dfaillance de
ces verrouillages.
32PD3000 / 42PD3000
DEUTSCH
SICHERHEITSVORKEHRUNGEN
WARNUNG: Die folgenden Vorkehrungen mssen
eingehalten werden.
ALLE PRODUKTE Bevor die Grundplatte
gewartet wird, sollte ein Trenntrafo zwischen die
Netzleitung und das Produkt eingebracht werden.
1. Wenn die Grundplatte in das Gehuse
zurckgestellt wird, stellen Sie sicher, dass alle
Schutzvorrichtungen wieder an ihrem Ort sind.
2. Wenn Wartung erforderlich ist, halten Sie die
originale Verdrahtungsart ein. Besondere Vorsicht
ist ntig, um die korrekte Verdrahtungsart in jedem
Hochspannungsstromkreis zu gewhrleisten.
3. Viele elektrische und mechanische Teile von
HITACHI Produkten haben besondere
sicherheitsbezogene Eigenschaften. Diese
Eigenschaften fallen oft nicht ins Auge, aber der
durch sie gewhrte Schutz kann nicht unbedingt
erreicht werden, wenn man Ersatzteile benutzt, die
fr hhere Spannung, Leistung usw. ausgelegt
sind. Ersatzteile, die diese besonderen
Sicherheitsmerkmale haben, sind in den
Prinzipskizzen und Ersatzteillisten an einem ! zu
erkennen. Der Gebrauch von Ersatzteilen, die nicht
dieselben Sicherheitsmerkmale haben wie die
empfohlenen HITACHI Ersatzteile, wie sie in der
Ersatzteilliste aufgefhrt sind, kann zu elektrischem
Schlag, Feuer, Rntgenstrahlung und anderen
Gefahren fhren.
4. Immer die originalen Abstandsstcke ersetzen
und die Leitungslngen beibehalten. Wo ein
Kurzschluss passiert ist, die Teile ersetzen, bei
denen berhitzung nachzuweisen ist.
5. Der Isolierwert sollte bei 500 V Gleichstrom
zwischen den Hauptpolen und allen zugnglichen
Metallteilen nicht unter 2M Ohm liegen.
6. Bei der Prfung auf Durchschlagsfestigkeit sollte
kein berschlag oder Durchschlag vorkommen,
wenn zwei Sekunden lang 3 kV Wechselstrom oder
4,25 kV Gleichstrom zwischen den Hauptpolen und
allen zugnglichen Metallteilen angelegt wird.
7. Bevor das gewartete Produkt dem Kunden
zurckgegeben wird, muss der Wartungstechniker
das Gert grndlich prfen, um sicherzustellen,
dass es betriebssicher ist ohne das Risiko eines
elektrischen Schlages. Der Wartungstechniker
muss sicherstellen, dass keine vom Hersteller im
Gert eingebaute Schutzvorkehrung schadhaft
geworden ist oder bei der Wartung unabsichtlich
beschdigt wurde.
CE KENNZEICHEN
1. HITACHI Produkte enthalten eventuell das CE
Kennzeichen auf dem Leistungsschild, welches
angibt, dass das Produkt Teile enthlt, die eigens
zugelassen sind, um bis zu einem spezifizierten
Niveau elektromagnetische Strfreiheit zu
bewirken.
2. Wenn Sie irgendein Teil in diesem Produkt
ersetzen, benutzen Sie bitte nur das korrekte Teil,
das in der Ersatzteilliste aufgefhrt ist, um
sicherzustell en, dass dieser Standard eingehalten
32PD3000 / 42PD3000
Contents
Safety .......................................................................................................................................................1
ENGLISH ............................................................................................................................................1
FRANAIS..........................................................................................................................................2
DEUTSCH ...........................................................................................................................................3
Contents ...................................................................................................................................................4
Lead Free Solder ......................................................................................................................................6
Specifications...........................................................................................................................................7
General Specifications .........................................................................................................................7
Features ;..............................................................................................................................................8
Service Data .............................................................................................................................................9
Block Diagrams .....................................................................................................................................16
AVC to PDP Block Diagram .............................................................................................................16
AVC Block Diagram..........................................................................................................................17
AVC Power Block Diagram ..............................................................................................................18
Major Connectors...............................................................................................................................19
Monitor Block Diagram.....................................................................................................................20
Schematic Drawing Descriptions...........................................................................................................21
Schematic Page 1 ; Tuner / Video Chroma........................................................................................21
Schematic Page 2 ; Sound / AV3 Control..........................................................................................23
Schematic Page 3 ; Interface Board (component input, progressive sync separation, centre audio
channel)..............................................................................................................................................25
Schematic Page 4 ; Power Circuit (Voltage Regulator) / Level Shifter ...........................................27
Schematic Page 5 ; Micro Controller.................................................................................................28
Schematic Page 6 ; COMB Filter / SVHS Output .............................................................................29
Schematic Page 7 ; SCART / FC-MSC Connection..........................................................................30
Schematic; AVC Power Supply.........................................................................................................32
Schematic Drawings ..............................................................................................................................33
Schematic Sheet 1 ..............................................................................................................................33
Schematic Sheet 2 ..............................................................................................................................34
Schematic Sheet 3 ..............................................................................................................................35
Schematic Sheet 4 ..............................................................................................................................36
Schematic Sheet 5 ..............................................................................................................................37
Schematic Sheet 6 ..............................................................................................................................38
Schematic Sheet 7 ..............................................................................................................................39
AV Power Schematic.........................................................................................................................40
AV Control Schematic.......................................................................................................................41
Signal / Sound Sheet 1 .......................................................................................................................42
Signal / Sound Sheet 2 .......................................................................................................................43
Signal / Sound Sheet 3 .......................................................................................................................44
Signal / Sound Sheet 4 .......................................................................................................................45
Filter, LED, Switch & Speakers ........................................................................................................46
Circuit Boards ........................................................................................................................................47
AV Board Side A ...............................................................................................................................47
AV Board Side B ...............................................................................................................................48
AV Power Side A...............................................................................................................................49
AV Power Side B...............................................................................................................................50
Signal / Sound Board Side A .............................................................................................................51
Signal / Sound Board Side B .............................................................................................................52
Filter, LEDs, Speaker PCBs...............................................................................................................53
Troubleshooting Flow Charts ................................................................................................................54
4
32PD3000 / 42PD3000
AV Power - 1 .....................................................................................................................................54
AV Power - 2 .....................................................................................................................................55
AV Power - 3 .....................................................................................................................................56
AV Circuit..........................................................................................................................................57
Assembly Drawings ...............................................................................................................................58
Audio / Video.....................................................................................................................................58
Wiring for Audio / Video Components .............................................................................................59
Monitor Front View ...........................................................................................................................60
Monitor Rear View ............................................................................................................................61
32 inch Monitor Wiring A .................................................................................................................62
32 inch Monitor Wiring B..................................................................................................................63
42 inch Monitor Wiring A .................................................................................................................64
42 inch Monitor Wiring B..................................................................................................................65
24way Digital Interface Cable Connection............................................................................................66
Microprocessor Pins...............................................................................................................................67
Connections to FC4................................................................................................................................69
PCB Connectors.....................................................................................................................................72
Replacement Parts..................................................................................................................................73
Signal / Sound Board .........................................................................................................................73
Filter Board ........................................................................................................................................75
32PD3000 ..........................................................................................................................................76
42PD3000 ..........................................................................................................................................77
Questions & Answers ............................................................................................................................79
32PD3000 / 42PD3000
Printed circuit board Assemblies using lead free solder shown below are engraved with an "F" following
Board Name.
The melting point of lead free solder is 40-50 C higher than one of leaded solder.
o
o
Soldering Part
PCB with surface mount devices
PCB without surface mount devices
Chassis, metallic shield, etc.
32PD3000 / 42PD3000
Specifications
General Specifications
Item
Spec
32PD3000 (PDP;32PD3000E+AVC;AV3000E) 42PD3000 (PDP;42PD3000E+AVC;AV3000E)
PDP panel
32" (ALSI for mat) Plasma display panel (16:9) , 42" (ALSI for mat) Plasma display panel (16:9) ,
resolution 852(H) x1024(V)
resolution 1024(H) x1024(V)
Display size 976(W) x 258(D) x 580(H)
unit: mm
1233(W) x 300(D) x 713(H)
unit: mm
Sound output Max. 10W x 2 (6 ohm)
Max. 12W x 2 (6 ohm)
level
Speaker
4 x 16 cm corn type x 2
???
Power supply AC 220 - 240 V 50Hz
AC 220 - 240 V 50Hz
Power
PDP 260W (stand-by <2W) AVC 30W, (stand- PDP 360W (stand-by <2W) AVC 30W, (standconsumption by <2W)
by <2W)
Colour system PAL/SECAM/NTSC4.43/NTSC3.58/PAL60
PAL/SECAM/NTSC4.43/NTSC3.58/PAL60
Sound system I/B.G.H/LL'
I/B.G.H/LL'
Tuning freq. 45MHz ~ 889MHz, VHF low/VHF
45MHz ~ 889MHz, VHF low/VHF
high/Hyper/UHF
high/Hyper/UHF
Position
100 (0~99) positions. Plus channel direct (C--/S- 100 (0~99) positions. Plus channel direct (C--/Sselection
-) and frequency direct (---.--MHz)
-) and frequency direct (---.--MHz)
PC input
Horizontal freq. 24KHz ~ 109KHz / Vertical freq. Horizontal freq. 24KHz ~ 109KHz / Vertical freq.
signal
50Hz ~ 85Hz
50Hz ~ 85Hz
Analogue RGB, input voltage 0.7Vpp/1.0Vpp
Analogue RGB, input voltage 0.7Vpp/1.0Vpp
selectable
selectable
H/V separate sync (TTL level) *** sound input ; H/V separate sync (TTL level) *** sound input ;
common with AV3 or AV4
common with AV3 or AV4
AV input
SCART101 (CVBS/SVHS/LR sound) - AV1
SCART101 (CVBS/SVHS/LR sound) - AV1
SCART102 (CVBS/RGB/LR sound) - AV2
SCART102 (CVBS/RGB/LR sound) - AV2
SCART100 (CVBS/RGB/LR sound) - AV3
SCART100 (CVBS/RGB/LR sound) - AV3
COMPONENT (YPbPr/YCbCr/LR sound) - AV4 COMPONENT (YPbPr/YCbCr/LR sound) - AV4
Front AV (CVBS/SVHS/LR sound) - FRONT
Front AV (CVBS/SVHS/LR sound) - FRONT
CENTRE AUDIO input
CENTRE AUDIO input
Dimensions PDP : 974(W) x 256(D) x 578(H) including
PDP : 1030(W) x ??(D) x 636(H) including
monitor stand
unit: mm
monitor stand
unit: mm
AVC : 430(W) x 293(D) x 121(H)
unit: mm AVC : 430(W) x 293(D) x 121(H)
unit: mm
Weight
PDP : 28.7kg (net)
PDP : 40.2kg (net)
AVC : 3.2kg (net)
AVC : 3.2kg (net)
Remote
2 x Hitachi R6P(G) * equivalent 'AA'
2 x Hitachi R6P(G) * equivalent 'AA'
control
batteries
32PD3000 / 42PD3000
Features ;
852x1024 resolution,
1024x1024 resolution,
Advanced progressive & 1024 interlace,
TruBass by SRS,
Which can be connected with DVD, Set Top Box, VCR and
Camera at the same time.
1 Component input,
PC input connection,
32PD3000 / 42PD3000
Service Data
Soft version
issue 1
New panel
2nd
3rd
4th
5th
V1.A4
functions
read
read
read
AGC data
OPT
80
80
80
AGC
adj
adj
adj
AGC adjustment
PC>
01-Nov-02
RED figures are new default
values
Device
BIF
adj
adj
adj
LIF
adj
adj
adj
AFC
read
read
read
01
01
01
gamma switch
PDP
FC4
5 D07:D00
6 D07:D00
PC1>
PC2>
PC3>
GSW
10 D3:D2
BLP
7F
7F
7F
COP
7F
7F
7F
Contrast (RGB)
FC4
MBC
7F
7F
7F
FC4
7 D15:D08
MCC
5D
5D
5D
FC4
7 D07:D00
MXB
6C
6C
6C
FC4
7 D15:D08
BGP
00
00
00
Brightness/Gradation
PDP
27&28 D2&D2
CCP
00
00
00
NTSC/EBU
PDP
27&28 D1&D1
DCP
01
01
01
Tracking correction
PDP
27&28 D0&D0
PSE
01
01
01
FC4
PST
0F
0F
0F
4 D08
OK
OK
OK
MAX
read
read
read
MIN
read
read
read
SNR
read
read
read
COL> R1
read
read
read
Gain R ; warm
PDP
Read/Write
13/20
1st D7:D0 /
D7:D0
G1
read
read
read
Gain G ; warm
PDP
Read/Write
13/21
2nd D7:D0 /
D7:D0
B1
read
read
read
Gain B ; warm
PDP
Read/Write
13/22
3rd D7:D0 /
D7:D0
NOM> R2
read
read
read
Gain R ; normal
PDP
Read/Write
12/17
1st D7:D0 /
D7:D0
G2
read
read
read
Gain G ; normal
PDP
Read/Write
12/18
2nd D7:D0 /
D7:D0
B2
read
read
read
Gain B ; normal
PDP
Read/Write
12/19
3rd D7:D0 /
D7:D0
WAM> R3
read
read
read
Gain R ; cool
PDP
Read/Write
11/14
1st D7:D0 /
D7:D0
G3
read
read
read
Gain G ; cool
PDP
Read/Write
11/15
2nd D7:D0 /
D7:D0
B3
read
read
read
Gain B ; cool
PDP
Read/Write
11/16
3rd D7:D0 /
D7:D0
01
01
01
gamma switch
PDP
SIG> FLA
GSW
WHB
00
00
00
HAPC
01
01
01
PDP
BRN
01
01
01
burn in mode
PDP
10 D3:D2
9 D3:D2&D1:D0
28
D4:D3
10 D5:D4
32PD3000 / 42PD3000
1st
2nd
3rd
4th
5th
M01>
M02>
M03>
picture mode
M04
picture mode
***
"PDP2_service05"
no.52
M06>
00
PDP
F01(4:3)
01
01
01
4:3
F02(16:9)
00
00
00
WIDE
SCREEN
F03(C16:9L) 00
00
00
LETTERBOX
F04(T16:9L) 01
01
01
T16:9L
F05(14:9)
01
01
01
14:9
F06(C14:9L) 00
00
00
C14:9L
F07(T14:9L) 01
01
01
T14:9L
F08(PAN)
01
01
01
PANORAMIC
F09(14:9LS) 00
00
00
14:9 ZOOM
PCA
02
02
02
FC4
3 D17:D16
HE1
02
02
02
Horizontal enhancer
DYNAMIC
FC4
2 D20:D19
HE2
03
03
03
Horizontal enhancer
DYNAMIC-VIDEO
FC4
2 D20:D19
HE3
00
00
00
Horizontal enhancer
NATURAL
FC4
2 D20:D19
HE4
00
00
00
Horizontal enhancer
NATURAL-VIDEO
FC4
2 D20:D19
HE5
01
01
01
2 D20:D19
2 D20:D19
10 D7
HE6
02
02
02
HET
00
00
00
FC4
2 D20:D19
VE1
03
03
03
FC4
2 D22:D21
2 D22:D21
VE2
03
03
03
VE3
03
03
03
FC4
2 D22:D21
VE4
03
03
03
2 D22:D21
VE5
03
03
03
FC4
2 D22:D21
03
FC4
2 D20:D19
03
03
VET
00
00
00
FC4
BGT
00
00
00
Brightness/Gradation
PDP
27&28 D2&D2
CCT
00
00
00
NTSC/EBU
PDP
27&28 D1&D1
TCR
01
01
01
PDP
27&28 D0&D0
2 D22:D21
27&28 D0&D0
DCC
00
00
00
WBC
00
00
00
BSO
1F
1F
1F
FC4
7 D21:D16
SPC
00
00
00
FC4
7 D07:D00
PHC
80
80
80
FC4
8 D07:D00
8 D07:D00
PHU
1A
1A
1A
NHU
20
20
20
FC4
8 D07:D00
1D
8 D07:D00
YU6
10
Device
00
VE6
M05>
functions
00
APC
MI0>
1D
1D
32PD3000 / 42PD3000
1st
2nd
3rd
MI1>
4th
M11>
M12>
picture mode
M13>
M14>
picture mode
5th
picture mode
M15>
functions
Device
YU5
1A
1A
1A
8 D07:D00
THU
1F
1F
1F
FC4
8 D07:D00
FC4
8 D07:D00
YHU
1F
1F
1F
FPB
00
00
00
BLT
7F
7F
7F
FC4
5 D07:D00
MBC
80
80
80
7 D15:D08
MBX
80
80
80
FC4
7 D15:D08
COT
7F
7F
7F
Contrast (RGB)
FC4
6 D07:D00
MCC
89
89
89
FC4
7 D07:D00
MCX
70
70
70
FC4
7 D07:D00
SAC
40
40
40
Saturation centre
NTSC/PAL/RGB/YCbCr TV
FC4
8 D14:D08
SAX
50
50
50
FC4
8 D14:D08
FC4
2 D12:D08
10 D6
CE1
1F
1F
1F
CE2
10
10
10
FC4
2 D12:D08
CE3
1F
1F
1F
FC4
2 D12:D08
CE4
10
10
10
FC4
2 D12:D08
CE5
1F
1F
1F
FC4
2 D12:D08
CE6
10
10
10
FC4
2 D12:D08
CET
10
10
10
FC4
2 D12:D08
YET
00
00
00
FC4
2 D04:D00
YE1
1F
1F
1F
sharpness DYNAMIC-TV
FC4
2 D04:D00
FC4
2 D04:D00
YE2
12
12
12
sharpness DYNAMICTVIDEO
YE3
12
12
12
sharpness NATURAL-TV
FC4
2 D04:D00
YE4
12
12
12
2 D04:D00
YE5
12
12
12
sharpness CINEMA-TV
FC4
2 D04:D00
YE6
12
12
12
sharpness CINEMA-VIDEO
FC4
2 D04:D00
YE7
12
12
12
sharpness centreFAVOURITE-TV
FC4
2 D04:D00
YE8
12
12
12
sharpness centreFAVOURITE-VIDEO
FC4
2 D04:D00
YI1
01
01
01
FC4
2 D07:D05
FC4
2 D07:D05
YI2
01
01
01
YI3
01
01
01
FC4
2 D07:D05
YI4
01
01
01
FC4
2 D07:D05
YI5
01
01
01
FC4
2 D07:D05
01
FC4
2 D07:D05
YI6
01
01
YIT
01
01
01
FC4
2 D07:D05
CI1
00
00
00
FC4
2 D15:D13
FC4
2 D15:D13
CI2
00
00
00
CI3
00
00
00
FC4
2 D15:D13
FC4
2 D15:D13
FC4
2 D15:D13
CI4
00
00
00
CI5
00
00
00
11
32PD3000 / 42PD3000
1st
2nd
3rd
4th
5th
CI6
M16
MI2>
M21>
M22>
M23>
M24>
MI3>
12
M31>
00
functions
Device
00
FC4
2 D15:D13
FC4
2 D15:D13
CIT
00
00
00
OSH
109
109
109
H position - OSD
OSV
40
40
40
V position - OSD
OTH
190
190
190
H position - TEXT
OTV
40
40
40
V position - TEXT
SUR
00
00
00
CMB
01
01
01
DCN
3E
3E
3E
DYNAMIC Contrast
DBR
80
80
80
DYNAMIC Brightness
DCL
50
50
50
DYNAMIC Colour
DPB
00
00
00
DCM
02
02
02
DBS
1F
1F
1F
DWB
00
00
00
DFT
01
01
01
NCN
38
38
38
NATURAL Contrast
NBR
80
80
80
NATURAL Brightness
NCL
48
48
48
NATURAL Colour
NPB
00
00
00
NCM
01
01
01
NBS
1A
1A
1A
NWB
00
00
00
NFT
01
01
01
TCN
3E
3E
3E
CINEMA Contrast
TBR
80
80
80
CINEMA Brightness
TCL
50
50
50
CINEMA Colour
TPB
00
00
00
TCM
00
00
00
TBS
1F
1F
1F
TWB
01
01
01
TFT
00
00
00
DGS
01
01
01
NGS
01
01
01
TGS
01
01
01
PGS
02
02
02
DPM
00
00
00
NPM
01
01
01
TPM
01
01
01
PPM
02
02
02
MVB
0B
0B
0B
PDP
10 D6
PDP
10 D6
PDP
10 D6
32PD3000 / 42PD3000
1st
2nd
3rd
4th
5th
functions
Device
MUSIC Treble
MTR
0B
0B
0B
MBA
0B
0B
0B
MUSIC Bass
MTB
03
03
03
MMS
01
01
01
NVB
0B
0B
0B
NTR
10
10
10
SPEECH Treble
NBA
0B
0B
0B
SPEECH Bass
NTB
00
00
00
NMS
00
00
00
TVB
0B
0B
0B
TTR
10
10
10
CINEMA Treble
TBA
10
10
10
CINEMA Bass
TTB
02
02
02
TMS
01
01
01
00
00
00
TC1
01
01
01
TDA9178 address 00
TDA9178
00
D07:D00
TC2
10
10
10
TDA9178 address 01
TDA9178
01
D05:D00
TC3
00
00
00
TDA9178 address 02
TDA9178
02
D07:D00
No individual parameter on
TC1~TC4 can be set.
TC4
00
00
00
TDA9178 address 03
TDA9178
03
D05:D00
M32>
M33>
MI4>
TDA9178 option
ABS
00
00
00
TDA9178 address 04
TDA9178
04
D05:D00
00
00
00
TDA9178 address 05
TDA9178
05
D05:D00
VGM
20
20
20
TDA9178 address 06
TDA9178
06
D05:D00
PKG
00
00
00
TDA9178 address 07
TDA9178
07
D05:D00
00
TDA9178 address 08
TDA9178
08
D05:D00
STP
M43>
M44>
00
00
CRG
00
00
00
TDA9178 address 09
TDA9178
09
D05:D00
LWD
00
00
00
TDA9178 address 0A
TDA9178
0A
D05:D00
1RD
14
14
14
1GD
0F
0F
0F
1BD
00
00
00
1RG
1F
1F
1F
1GG
1F
1F
1F
1BG
1F
1F
1F
2RD
00
00
00
2GD
00
00
00
2BD
00
00
00
2RG
1F
1F
1F
2GG
1F
1F
1F
2BG
1F
1F
1F
13
32PD3000 / 42PD3000
1st
2nd
3rd
4th
functions
00
00
00
3GD
0F
0F
0F
3BD
29
29
29
3RG
1F
1F
1F
3GG
1F
1F
1F
3BG
1F
1F
1F
0D
0D
0D
CEB
0D
0D
0D
CEC
0D
0D
0D
CED
0D
0D
0D
CEE
0D
0D
0D
CEF
0D
0D
0D
CEM
10
10
10
YEA
10
10
10
sharpness DYNAMICRGB/YCbCr
YEB
10
10
10
sharpness DYNAMIC-YPbPr
sharpness NATURALRGB/YCbCr
MI5>
add 27 bytes
M52>
YEC
08
08
08
YED
02
02
02
sharpness NATURAL-YPbPr
YEE
10
10
10
sharpness CINEMARGB/YCbCr
YEF
10
10
10
sharpness DYNAMIC-YPbPr
YE9
10
10
10
sharpness centre on
FAVOURITE-RGB/YCbCr
YE0
10
10
10
sharpness centre on
FAVOURITE-YPbPr
1F
1F
1F
LC2
10
10
10
LC3
0D
0D
0D
LC4
0D
0D
0D
M54>
14
3RD
M45>
OPT> OB0
5th
DCV
50
50
50
DYNAMIC + VIDEO/RGB ;
color
NCV
3E
3E
3E
NATURAL + VIDEO/RGB ;
colour
TCV
40
40
40
CINEMA + VIDEO/RGB ;
colour
SAV
3E
3E
3E
FAVOURITE + VIDEO/RGB ;
colour
DCO
58
58
58
DYNAMIC + YCbCr/YPbPr ;
colour
NCO
4B
4B
4B
NATURAL + YCbCr/YPbPr ;
colour
TCO
50
50
50
CINEMA + YCbCr/YPbPr ;
colour
SAO
44
44
44
FAVOURITE + YCbCr/YPbPr
; colour
78
78
78
option byte 1
Device
32PD3000 / 42PD3000
1st
2nd
3rd
4th
5th
OB1
80
80
80
option byte 2
EMG
0:Normal, 1:Macrovision
improved
AV DELAY
OFF
OFF
OFF
RGB Comb
OFF
OFF
OFF
ASIAN
OPTIONS>
PRG
AV2
INITIAL INSTALL ON
ON
ON
COUNTRY
SELECT
ON
ON
ON
LANGUAGE
SELECT
ON
ON
ON
TELETEXT
ON
ON
ON
HOT> OPT
VOL
bar
read
read
read
Model name
MSU
read
read
read
PDU
read
read
read
PWT
read
read
read
VRS> MN
Device
FC4
E2>
functions
E2R
OK
OK
OK
EEPROM reset
E2F
OK
OK
OK
E2S
OK
OK
OK
E24
OK
OK
OK
EEPROM in FC4 is
initialised
EXS
OK
OK
OK
15
32PD3000 / 42PD3000
Block Diagrams
AVC to PDP Block Diagram
16
32PD3000 / 42PD3000
AVC Block Diagram
17
32PD3000 / 42PD3000
AVC Power Block Diagram
18
32PD3000 / 42PD3000
Major Connectors
19
32PD3000 / 42PD3000
Monitor Block Diagram
20
32PD3000 / 42PD3000
21
32PD3000 / 42PD3000
input
pin 14
pin 16
pin 18
pin 20
pin 21
pin 23
pin 24
pin 28
pin 29
TV signal input
CVBS - SCART102 (AV2) input
CVBS - SCART100 (AV3) input
CVBS/Y - SCART101 (AV1) input
C - SCART101 (AV1) input
CVBS/Y - front AV (FRONT) input
C - front AV (FRONT) input
Y - from COMB filter
C - from COMB filter
input
control
pin 15
pin 17
---
output
pin 26
pin 32
pin 34
output
control
pin 20
pin 22
22
32PD3000 / 42PD3000
IC301
X300
QSS signal is coming from IC100 to pin 58 through amplifier Q308/307. The signal
level at pin 58 should be 0.1 ~ 0.8Vpp.
Sound output L/R at pin 28 and 29 are connected through amplifier Q310/Q312 for L
and Q309/Q311 for R to adjust 500mVrms at PL700 pin 4 and 6 In the condition of AV
sound input 500mVrms, FM modulation 54%
Sound output L/R at pin 28 and 29 are also connected through IC300 TDA7433 and
IC303 to headphone.
* Audio switch
input
pin 52
pin 53
pin 49
pin 50
pin 46
pin 47
pin 43
pin 44
pin 55
output
pin 37
pin 36
pin 34
pin 33
pin 29
pin 28
output
pin 5
IC300
input
Monitor sound L/R outputs for speaker are connected headphone and phone out. IC300
contributes separate volume control
pin 6
Audio sound L input
pin 5
Audio sound R input
23
32PD3000 / 42PD3000
output
pin 16
pin 15
pin 14
pin 13
IC303
****
PL300
IC302
TDA8440 is the option in the future. This is not used for this model.
(OPTION)
24
32PD3000 / 42PD3000
IC08
XC01
IC02/IC03
input
output
control
IC02
IC03
32PD3000 / 42PD3000
IC04
IC05
IC06
IC07
Audio switch, main L/R or AV4 (components input) L/R. main L/R comes
from MSP3410 audio switch.
Video switch, Front video or AV4 (in case of YCbCr normal components),
which is connected to TDA9321 for sync separation
Audio switch, Centre sound or AV4 (components input) L/R. Output goes
to IC04 to switch another audio input.
IC09
26
32PD3000 / 42PD3000
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
POWER1
N.C.
N.C.
N.C.
+5VSTB
GND
N.C.
N.C.
GND
GND
+5.5V1
GND
+9.5V1
GND
+5.5V2
GND
+9.5V2
GND
FE+30V
H;ON, L;Stand-by
5.5V supply 1
9.5V supply 1
5.5V supply 2
9.5V supply2
30V supply for tuner
Voltage regulators
I603
BA06T
IC602 SI-3050LSA
IC603 SI-3050LSA
IC601 SI-3033LSA
Q602
TK11125M
IC604 BA09FP
Q607
Q603
Q604
Q605
Q614
BSS138
2SC2412K
2SC2412K
2SC2412K
BSS138
32PD3000 / 42PD3000
28
PIN NAME
PL702 IN/OUT
FUNCTIONS
POW LED
POWER SAVE
STB+5V
GND
RM-IN
A+5V
A/D KEY 2
A/D KEY 1
(BS-LED)
(MODEM-LED)
I
I
I
O
I
O
O
at Front Control
Power LED
POWER2
Stand-by 5V power supply
GND
N.C.
+5V
Key in 1
Key in 2
N.C.
N.C.
32PD3000 / 42PD3000
IC101
functions
GND
GND
GND(SW)
29
32PD3000 / 42PD3000
SCART connectors
pin
SCART101
SCART102
SCART100
AV1
AV2
AV3
general spec
sound input
R
GND
GND
GND
GND
GND
GND
Blue return
sound input
L
sound input
L
sound input
L
N.C.
Blue-in
Blue-in
sound input
R
sound input
R
switch
switch
switch
GND
GND
GND
Green return
10
AVLINK
N.C.
N.C.
11
N.C.
Green-in
Green-in
12
N.C.
N.C.
N.C.
under consideration
13
GND
GND
GND
Red return
14
GND
GND
GND
Blanking return
15
C in
Red-in
Red-in
16
N.C.
Fast
Blanking
Fast
Blanking
17
GND
GND
GND
18
GND
GND
GND
19
TV output
Monitor
output
Monitor
output
20
CVBS/Y in
CVBS in
CVBS in
21
GND
GND
GND
32PD3000 / 42PD3000
31
32PD3000 / 42PD3000
pin 1
feedback input
pin 2
pin 3
pin 4
pin 5
GND
pin 5
pin 7
feedback input-1
pin 8
feedback input-2
output pin 6
pin 9
I902
photocoupler ; TLP621
I930
input pin 11
pin 15
output pin 7
I931
DC voltage input
feedback input
switching output
input pin 5
feedback input
pin 2
output ON/OFF
output pin 4
I932
DC voltage input
pin 8
switching output
DC voltage input
DC +5V output
I933
input pin 1
feedback input
pin 5
output ON/OFF
output pin 2
PSP
DC voltage input
pin 4
switching output
32
32PD3000 / 42PD3000
Schematic Drawings
33
32PD3000 / 42PD3000
34
32PD3000 / 42PD3000
35
32PD3000 / 42PD3000
36
32PD3000 / 42PD3000
37
32PD3000 / 42PD3000
38
32PD3000 / 42PD3000
39
32PD3000 / 42PD3000
40
32PD3000 / 42PD3000
41
32PD3000 / 42PD3000
42
32PD3000 / 42PD3000
43
32PD3000 / 42PD3000
44
32PD3000 / 42PD3000
45
32PD3000 / 42PD3000
46
32PD3000 / 42PD3000
Circuit Boards
47
32PD3000 / 42PD3000
48
32PD3000 / 42PD3000
AV Power Side A
49
32PD3000 / 42PD3000
AV Power Side B
50
1
L
Position
Cir.No.
Position
Cir.No.
Position
Cir.No.
Position
Cir.No.
Position
Cir.No.
Position
Cir.No.
Position
D003
D401
D402
D403
D404
D405
D406
D408
D409
D410
D413
D414
D415
D600
D601
C4
K4
K3
K3
K4
J4
J2
J2
I3
I1
H4
K2
I3
E1
E1
D602
D603
D604
D605
D606
D607
D610
D611
DP01
DS01
DS02
DS03
DS04
I001
I002
F1
F1
E1
E1
F1
E1
D2
D2
F5
A2
A2
A3
B4
C3
B3
I003
I201
I202
I600
I601
I602
I603
IC401
IC402
IC403
IP02
L201
L202
L203
L204
C4
D5
B5
E2
G2
G3
D1
H2
J2
J1
F5
B5
B5
D5
C5
L600
L601
L602
L603
L604
LP02
LP04
PDA1
PDS
PSC2
Q001
Q002
Q003
Q005
Q006
D2
E2
E2
E3
G3
F4
E5
H6
A5
G6
C4
C2
C2
G5
G5
Q201
Q202
Q203
Q204
Q401
Q402
Q403
Q404
Q405
Q406
Q407
Q408
Q600
Q601
Q602
D4
D4
C6
C6
I4
J4
J3
K1
K1
I3
H4
J3
F2
F2
G2
QP01
QS04
TP001
TP002
TP601
X001
X002
X201
X202
X203
X204
X600
X601
X602
X603
E5
A2
D3
C4
D2
G5
D3
B5
B5
B5
C4
G1
G1
G1
G1
X604
X605
XS01
XS02
XS03
G1
F1
A2
B1
B1
1
A
Position
D001
D608
D609
QS01
D3
F2
F2
B4
FILTER board
32PD3000 / 42PD3000
54
AV Power - 2
32PD3000 / 42PD3000
55
32PD3000 / 42PD3000
AV Power - 3
56
AV Circuit
32PD3000 / 42PD3000
57
32PD3000 / 42PD3000
Assembly Drawings
Audio / Video
58
32PD3000 / 42PD3000
Wiring for Audio / Video Components
Specification
1. This Drawing shows the wire dressing and connectors' connection of
AVC3-E Final Assy.
2. Connectors with wire should be inserted into Plug Pin Posts as
shown on the table below
Connector with wire
Name Assy List
ESC FINAL ASSY
EFP1 FINAL ASSY
EFP2 FINAL ASSY
ESF FINAL ASSY
PSP Power Board Assy
Plug Pin 1
Board
Control Board
Power Board
Power Board
AV Board
AV Board
Name
PSC
PFP1
PFP2
PSF
PSP
Plug Pin 2
Board
AV Board
HCP111
HCP111
HCP111
-
Name
PL702
P002P
P003P
P001
-
3. Into Plug Pin Post with Lock function, connector housing should be
inserted deeply until it can be locked.
4. Into Plug Pin Post without Lock function, connector housing should be
inserted most deeply.
5. Flexible Flat Cable ESF should be fixed as shown on the drawing below
position
and lock
10
150
10
59
32PD3000E
42PD3000E
32PD3000E
42PD3000E
Code
SIGNAL Board
AC INLET
Material
POLYCARBONATE+
PC+ABS
ACRYLONITRILE BUTADIENE STYRENE
PS
POLYSTYRENE
FILTER Board
LED Board
(PS)
(PC+ABS)
Colored metal plate
(PS)
32PD3000E
42PD3000E
32PD3000E
42PD3000E
Code
(PC+ABS)
Material
ABS
POWER UNIT
SIGNAL/SOUND
Board Assembly
(ABS)
(PC+ABS)
(AL)
(PC+ABS)
(ABS)
(PC+
ABS)
(PC+ABS)
(PC+ABS)
(PC+
ABS)
32PD3000 / 42PD3000
32 inch Monitor Wiring A
62
32PD3000 / 42PD3000
32 inch Monitor Wiring B
63
32PD3000 / 42PD3000
42 inch Monitor Wiring A
64
32PD3000 / 42PD3000
65
32PD3000 / 42PD3000
PDP
AVC(FC4)
P302P
TC57587-01-401
PDP
TX2-
TX2-
1 TXD
TXD
TX2+
TX2+
2 RXD
RXD
SHIELD
---
SHIELD
3 PARITY
PARITY
N.C.
---
N.C.
4 REMO-PDP
REMO-PDP
N.C.
---
N.C.
5 AUDIO L
AUDIO L
SCLH
SCLH
6 AUDIO R
AUDIO R
SDAH
SDAH
7 PDDET
PDDET
N.C.
N.C.
8 AVDET2
AVDET2
TX1-
---
TX1-
10 TX1+
TX1+
11 SHIELD
---
SHIELD
12 N.C.
---
N.C.
13 N.C.
---
N.C.
14 +5VAVDET
15 GND
+5VAVDET
---
GND
16 HPDET
HPDET
17 TXD-
TXD-
18 TXD+
TXD+
19 SHIELD
---
SHIELD
20 N.C.
---
N.C.
21 N.C.
---
N.C.
22 SHIELD
---
SUIELD
23 TXC+
TXC+
24 TXC-
TXC-
66
32PD3000 / 42PD3000
Microprocessor Pins
Pin
No.
INVERTED (I)
FUNCTION OR BUFFERED IN/OUT
(B)
FUNCTION
Port 0
0.
9
0
0.
10
1
0.
11
2
0.
12
3
0.
13
4
0.
14
5
0.
15
6
0.
16
7
Port 1
1.
41
0
1.
42
1
1.
43
2
1.
44
3
1.
45
4
1.
46
5
1.
47
6
1.
52
7
Port 2
24
POWERON
IN
POWER1
OUT
POWER2
OUT
(I) POWERLED 5V
(I) OSDRESET
OUT
OUT
(I) 3WBCLOCK 5V
(I) FCENABLE 5V
(I) MSCENABLE 5V
OUT
OUT
Power key
standon
input
by
Power control H(1.5V)
L
1
Power control H(1.0V)
L
2
Power LED H(1.5V) H(1.5V)
control
L
H(1.5V)
PDP reset
EEPROM
enable
AV link
output
OUT
3 wire bus
clock
OUT
FC enable
OUT
MSC enable
OUT
3WBDATA
PC OSD
enable
MSP3410
(I) MSP-RESET OUT
reset
(B) 3WBIN/OU 3 wire buses
DATA+5V
T
data
SCL-3V3
(B) SCL+5V
OUT
SDA-3V3
(B) SDA+5V
IN/OU
I2C bus data
T
FROM
IN
SCART1 PIN 8
H(1.2V)
PC OSD reset
(I) OSD-EN
2.
ADC0
0
power
save
Scart 101
(AV1) pin 8
detect
67
32PD3000 / 42PD3000
2.
ADC1
1
2.
26
PDDET
2
25
27
2.
ADC3
3
Port 3
3.
31
IF TRAP
0
32
3.
SCI
2
3.
34
IR1
3
FRONT3.
35
SVHS4
SOCKET
3.
36
MAP1
5
3.
37
MAP2
6
3.
1900RX
7
Port 4
4.
48
MEM RD#
2
4.
49
MEM WR#
3
68
FROM PDP
IN
FROM FRONT
IN
SWITCHES
ADJACENT
CHANNELS
3. 1900TX1 3v3
33
38
FROM TUNER
IN
AGC
FROM
AVLINK
OUT
Not used
OUT
PDP
communicatio
n via RS232C
IN
AV link input
IR FROM PDP IN
IN
A18 ON SRAM OUT
A15/A18
SWITCH
AGC level
detect
PDP ON
detect
Vol+/&Prog.+/- key
input
OUT
IN
OUT
OUT
IR input
S-VHS socket
detect
SRAM
mapping
SRAM
mapping
PDP
communicatio
n via RS232C
SRAM output
enable
SRAM write
enable
32PD3000 / 42PD3000
Connections to FC4
PSF at AVC
P001 at FC4
PIN NAME
PIN NAME
GND
GND
I/O
N.C.
N.C.
I/O
GND
GND
DATA
DATA
I/O
CLK
CLK
GND
Pin
No.
IN/OUT FUNCTIONS
NOTE
GND
3 wires DATA
5V CMOS
3 wires CLOCK
5V CMOS
GND
GND
FC-ENA
FC-ENA
FC micro enable
5V CMOS
MSC-ENA
OSD-CS
5V CMOS
DATA
OSD-DATA
3 wires DATA
5V CMOS
10
CLK
OSD-CLK
3 wires CLOCK
5V CMOS
11
GND
GND
GND
12
N.C.
N.C.(2H)
13
N.C.
K_DET
14
N.C.
N.C.(2V)
15
N.C.
KMASK
16
GND
GND
GND
17
RS232CPDP(TxD)
32C-PDP (TXD)
RS232C-TxD
5V CMOS
18
RS232CPDP(RxD)
32C-PDP (RXD)
RS232C-RxD
5V CMOS
19
GND
GND
GND
20
+5VSTB
AVDET
PDP control
21
N.C.
N.C.
MATRIX control
22
Remo-PDP
Remo-PDP
23
GND
N.C.
GND
24
PM RST
PM RST
PDP control
5V CMOS
25
PD DET
PD DET
PDP control
5V CMOS
26
GND
GND
GND
27
MY
MY
Video Y
1.4V0.06Vp-p
28
MCb
MCb
Video Cb
0.7v0.03Vp-p
29
MCr
MCr
Video Cr
0.7v0.03Vp-p
69
32PD3000 / 42PD3000
30
GND
GND
GND
31
MH
MH
Main H sync
5V CMOS
32
MV
MV
Main V sync
5V CMOS
33
GND
GND
GND
34
SY
SY
Sub Y/G
1.4V0.06Vp-p (Y) /
0.7Vpp0.03Vpp (G)
35
SCb
SCb
Sub Cb/B
0.7v0.03Vp-p
36
SCr
SCr
Sub Cr/R
0.7v0.03Vp-p
37
GND
GND
GND
38
SH
SH
Sub H sync
5V CMOS
39
SV
SV
Sub V sync
5V CMOS
40
GND
GND
GND
41
GND
GND(OSD/TXT
G)
GND
42
GND
GND(OSD/TXT
B)
GND
43
GND
GND(OSD/TXT
R)
GND
44
GND
GND(OSD
BLK/Ys)
GND
45
GND
GND(OSD/Ym)
GND
46
GND
GND
GND
47
AUDIO L
AUDIO L
Audio L
48
GND
GND
GND
49
AUDIO R
AUDIO R
Audio R
50
GND
GND
GND
P002P
PIN
NO.
PIN NAME
typ 500mVrms
at FC4
IN/OUT FUNCTIONS
FA+6.0V
6V power supply
FA+6.0V
6V power supply
GND
GND
GND
GND
FSTB+5V
Stand-by +5V
FSTB+5V
Stand-by +5V
GND
GND
70
typ 500mVrms
NOTE
460mA
50mA
32PD3000 / 42PD3000
P003P
PIN
NO.
PIN NAME
at FC4
IN/OUT FUNCTIONS
D+1.8V
D+1.8V
GND
GND
GND
GND
D+3.3V
D+3.3V
D+3.3V
GND
GND
GND
GND
NOTE
500mA
350mA
71
32PD3000 / 42PD3000
PCB Connectors
AVC
ESC 2908877
FINA
Contr
AV
L
EA00069 CPC10PH2R0HTP
PL70 EA00349 CPC10PH2R0VTP
CO-10C-C2R0-431 ol
PSC
Boar
ASS
R
H-SM3
2
R
H-SM3
Board
d
Y
FINA
EFP
L
CO-07C-C1R5EF22161
1
ASS 391-ZH
Y
FC4
FINA
EFP
L
CO-09C-C1R5EF22171
2
ASS 391-ZH
Y
FC4
FINA
L
PRW-SML2CDASS 50P-L700
Y
AV
EA00932 CPC50FP0R5VTPSF
Board
R
FH12
FC4
P001
EA01561 CPC50FP0R5HTR
FLZX
ESF EK01108
PSP
Powe
CPCPED04153 r
AV
ED04163
19BP1R2VU1.25F
PSP
19BS1R2VU1.25F U
Boar
Board
U
JN
JN
d
FC4
P001
PJX-DVI(F)24P RA SOK
P302P EY01491
PJX-YKF51-5376
For Alignment
P601P EY01062
PC Input Terminal
PJX-DSUB JACK
AV Board
PSF
EA00932R CPC50FP0R5VT-FH12
P001 FC4
PSP
P002P FC4
P003P FC4
72
No ITEM
1 CVBS &
S.INPUT
SOFTER
POTENTIAL PROBLEM/QUESTION
CVBS and S-VHS input is softer than
CL32PD2100 (with NR=off).
When DVD signal input through AV1, Front by
CVBS or S-VHS, picture is soft.
LTI EFFECT
Luminance
Transient
Improvement
NOISE
REDUCTION
EFFECT
79
NOTE
No ITEM
POTENTIAL PROBLEM/QUESTION
Reduction on 32PD3000. YNR and CNR. YNR ;
Luminance noise is reduced without affecting
Chrominane transient. CNR ; Chrominace noise
is reduced without loosing sharpness of picture
(Luminance)
WHITE BALANCE adjustment is done by menu
WHITE
bar. COOL/NORMAL/WARM selection is also
BALANCE
possible but in service menu. In Picture mode is
selected as shown below. DYNAMIC ; COOL
NATURAL ; COOL
CINEMA ; NORMAL
FAVOURITE ; COOL
CLOCK NOISE When selecting CENTRE speaker or AV4
mode, you can hear clock noise in sound when
ON SOUND
volume level is increased
more than half. This is caused by cross-talk in
the cable. AV4 sound and centre sound are
located after audio decoder (MSP3410) which
leads audio input impedance
When you see streak noise on RGB input, this is
RGB MODE
caused by clamping error accidentally.
STREAK
NOISE
In service mode, check SVC > OPT > RGB Comb = off
MENU
WIDEMODE
PC WINDOW
LIMITATION
80
NOTE
No ITEM
10 PICTURE
MODE
11 AUDIO MODE
12 TRUBASS &
MATRIX
SURROUND
13 AV4
Components
INPUT
14 TV + TEXT
81
POTENTIAL PROBLEM/QUESTION
Picture mode provides 4 kinds of modes.
DYNAMIC, NATURAL, CINEMA,
FAVOURITE
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
SM003
HITACHI
NO P OW E R
NOP OW E R
NO V s ,V a,V cc,S T B
NG
FUS E
OK
impedance check
D001
NG
OK
D001
impedance checkQ003/Q004
NG
OK
Q003/Q004,
etc
NG
STB
impedance check
Q201
OK
check voltage
D011(k)-J13
over 130V
under 130V
NO PICTURE
& S OU ND
STB
Q201,IC201
D210,Q202,etc
impedance check
Q301
D161,IC101,Q104,
Q108,etc
Q103,R 005
NG
OK
NG
Q301,IC301
D301,Q303,etc
NO V s ,V a,V cc
NG
S ee NO P OW E R
OK
OK
V cc
NG
over 300V
check voltage
J58 - J13
under 300V
IC201,Q202,P C201,
P C202,P C252,P C256,
D210,etc
I C001,D005D008,
R L 001,P C003,Q010,etc
NO PICTURE
i mpedance check
V s L I NE
N O V s ,V a
NG
OK
i mpedance check
V a L I NE
NG
OK
V a:no upr i s e
V s :down after up
S W ON
open connector
CN 64,CN 66CN67
V s :no upr i s e
V a:down after up
i mpedance check
V a L I NE
open connector
CN64,CN65
OK
NG
I C301,Q303,
P C301,P C302
D 310,I C391,
etc
SM003
I C591,Q501,
I C501,D 532,
Q530,P C501,
P C502,D 280,
D 281,etc
D 351
impedance check
V s L INE
OK
NG
P DP module V a
NG
D551,D552
P DP module V s
NG
HITACHI
HITACHI Europe AB
Box 77 S-164 94 Kista
SWEDEN
Tel: +46 (0) 8 562 711 00
Fax: +46 (0) 8 562 711 13
Email: csgswe@hitachi-eu.com
HITACH EUROPE AB
Egebkgrd
Egebkvej 98
DK-2850 Nrum
DENMARK
Tel: +45 43 43 6050
Fax: +45 43 60 51
Email: csgnor@hitachi-eu.com
HITACHI EUROPE AB
Neopoli / Niemenkatu 73
FIN-15140 Lahti
FINLAND
Tel : +358 3 8858 271
Fax: +358 3 8858 272
Email: csgnor@hitachi-eu.com
www.hitachidigitalmedia.com