Escolar Documentos
Profissional Documentos
Cultura Documentos
4014N
4014NV
DOUBLE
INSULATION
SPECIFICATIONS
Model
4014N
Capacities
Air pressure (water column) ...................................................... 560 mm
Air volume ................................................................................ 2.8 m3/min.
No load speed (min1) ................................................................ 16,000
Overall length .............................................................................. 430 mm
Net weight ................................................................................... 1.75 kg
4014NV
0 560 mm
0 2.8 m3/min.
0 16,000
430 mm
1.75 kg
Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can,
therefore, also be used from sockets without earth wire.
For European countries only
EC-DECLARATION OF CONFORMITY
ENH101-4
ENG005-2-V3
Yasuhiko Kanzaki
CE 2005
Director
Symbols
The followings show the symbols used for the tool. Be sure that you understand their meaning before use.
2
4
2
7
6
5
4
7
6
8
11
10
12
13
7
3
ENGLISH
Explanation of general view
1
2
3
4
5
Nozzle
Blower outlet
Suction inlet
Dust bag
Fastener
6
7
8
9
10
Switch trigger
Lock button
Speed control screw
Lower
Higher
11 Limit mark
12 Screwdriver
13 Brush holder cap
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Personal safety
9. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
10. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
MAINTENANCE
Service
23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
24. Follow instruction for lubricating and changing
accessories.
25. Keep handles dry, clean and free from oil and
grease.
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
5.
6.
7.
ACCESSORIES
CAUTION:
These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
Switch action
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the OFF
position when released.
For 4014N (Fig. 4)
To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
For 4014NV (Fig. 5)
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from
the locked position, pull the trigger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclockwise
for lower speed.
Joint
Flexible hose
Corner nozzle
Straight pipe
Nozzle assembly
Nozzle assembly (long size)
Dust bag assembly
Makita Corporation
Anjo, Aichi, Japan
883440A221