Escolar Documentos
Profissional Documentos
Cultura Documentos
M185XW01 V8
AU OPTRONICS CORPORATION
(V ) Preliminary Specification
( ) Final Specification
Module
Model Name
M185XW01 V8
Customer
Date
Approved by
Winnie Chang
Approved by
Date
2009/12/01
Prepared by
www.DataSheet.co.kr
Weiyen Tseng
2009/12/01
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Contents
1.0 Handling Precautions .....................................................................................4
2.0 General Description ........................................................................................5
2.1 Display Characteristics....................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Record of Revision
Version and
Date
0.1
2009/12/01
Page
Old description
New Description
All
N/A
Remark
www.DataSheet.co.kr
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
10)
11)
Since front polarizer is easily damaged, pay attention not to scratch it.
Be sure to turn off power supply when inserting or disconnecting from input connector.
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
Do not open or modify the Module Assembly.
Do not press the reflector sheet at the back of the module to any directions.
In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.DataSheet.co.kr
12)
13)
14)
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Unit
[mm]
[mm]
[um]
[cd/m2]
[msec]
[Volt]
[Watt]
[Grams]
[mm]
[oC]
[oC]
SPECIFICATIONS
470.1(18.51)
409.8 (H) x 230.4 (V)
1366(x3) x 768
300 (per one triad) 300
R.G.B. Vertical Stripe
TN Mode, Normally White
2
200 cd/m (@ 7.5mA (Typ.)
700 (Typ.)
5ms (Typ., on/off)
+5.0 V (Typ)
15.2 W (Typ)
(without inverter, all black pattern)
1460 (Typ.)
430.37 (W) x 254.6 (H) Typ. x 11 (D) Max.
One channel LVDS
16.7M colors (RGB 6-bit + Hi_FRC )
Anti-Glare, 3H
www.DataSheet.co.kr
0 to +50
-20 to +60
RoHS Compliance
N/A
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Horizontal
CR = 10
(Right)
(Left)
80
90
Max.
-
Vertical
CR = 10
(Up)
(Down)
65
55
420
700
3.6
5.7
1.4
2.3
Raising + Falling
Red x
0.607
0.637
0.667
Red y
0.308
0.338
0.368
Green x
0.264
0.294
0.324
Green y
0.567
0.597
0.627
Blue x
0.118
0.148
0.178
Blue y
0.041
0.071
0.101
0.283
0.313
0.343
0.299
0.329
0.359
[cd/m ]
160
200
Luminance Uniformity
[%]
75
80
[%]
1.5
Flicker
dB
-20
Viewing Angle
Unit
[degree]
Contrast ratio
Response Time
Conditions
Normal Direction
[msec]
Color / Chromaticity
Coordinates (CIE)
White x
Color Coordinates (CIE) White
Central Luminance
White y
2
Min.
Typ.
Note
www.DataSheet.co.kr
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Photo detector
Measured distance
LCD Panel
TFT-LCD Module
www.DataSheet.co.kr
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Tr F
Tr R
100
90
Optical
W hite
Black
Black
W hite
response
10
0
1 Frame
1 Frame
SR-3
Uniformity =
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
CT = | YB YA | / YA 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
RGBRGB
Gray Level = L127
www.DataSheet.co.kr
RGBRGB
Gray Level = L0
RGBRGB
AC
DC
Time
AC Level(at 30 Hz)
DC Level
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
AUO
ASIC
LVD
Connector
+5V
Y-Driver IC
LVDS
Receiver
G1
Timing
Controller
RSDS
Transmitter
TFT-LCD
1366(x3) x 768
Pixels
X-Driver IC
G768
D1
D4098
2 CCFL
DC/DC
Converter
Gamma
Correction
www.DataSheet.co.kr
I/F + X-PCB
DC
Inverter
10
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Symbol
Min
Max
Unit
Conditions
VDD
4.5
+5.5
[Volt]
Note 1,2
Item
Symbol
Min
Max
Unit
Conditions
CCFL Current
ICFL
3.0
8.0
[mA] rms
Note 1,2
Logic/LCD Drive
Voltage
Symbol
Min.
Max.
Unit
Conditions
Operating Temperature
TOP
+50
[ C]
Operation Humidity
HOP
90
[%RH]
Storage Temperature
TST
-20
+60
[oC]
Storage Humidity
HST
90
[%RH]
Note 3
www.DataSheet.co.kr
Operating Range
document version 0.1
Storage Range
11
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Symbol
Parameter
Min
Typ
Max
Unit
VDD
Logic/LCD Drive
Voltage
4.5
5.0
5.5
[Volt]
IDD
Input Current
0.84
[A]
PDD
VDD Power
4.2
[Watt]
IRush
Inrush Current
[A]
VDDrp
Allowable Logic/LCD
Drive Ripple Voltage
350
[mV] p-p
Conditions
+/-10%
Note 1
VDD= 5.0V, All Black Pattern
At 60Hz
www.DataSheet.co.kr
Q3
AO6402
D6
D5
D2
D1
F1
S
VCC
R1
47K
C1
1uF/16V
D1
D2
D5
D6
(High to Low)
Control
Signal
Q3
AO6402
R2
G
S
1K
2
C3
+12.0V
SW1
SW MAG-SPST
1
VR1
0.01uF/25V
47K
C2
1uF/25V
12
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
VID
Parameter
Differential Input High
Threshold
Differential Input Low
Threshold
Input Differential Voltage
Min
Typ
Max
Units
+50
+100
[mV]
-100
-50
[mV]
100
400
600
[mV]
+1.4
[V]
Condition
VICM = 1.2V
Note 1
VICM = 1.2V
Note 1
Note 1
www.DataSheet.co.kr
VICM
+1.0
+1.2
VID
VTH
VTL
VICM
VSS
13
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Min.
Typ.
Max.
7.0
7.5
8.0
[mA] rms
3.0
7.5
8.0
[mA] rms
40
50
80
[KHz]
1650
[Volt] rms
1250
[Volt] rms
700
(@7.5mA)
11
50,000
)
CCFL Ignition Voltage (ViCF, Ta= 25 )
CCFL Ignition Voltage (ViCFL, Ta= 0
Unit
Note
2
3, 4
[Volt] rms
6
[Watt]
-
[Hour]
14
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
www.DataSheet.co.kr
15
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
768 Line
1365 1366
R G B R G B
R GB R G B
R G B R G B
R GB R G B
www.DataSheet.co.kr
16
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
www.DataSheet.co.kr
17
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
DESCRIPTION
NC
NC
NC
GND
Power Ground
RXIN0-
RXIN0+
GND
Power Ground
RXIN1-
RXIN1+
10
GND
Power Ground
11
RXIN2-
12
RXIN2+
13
GND
Power Ground
14
RXCLKIN-
15
RXCLKIN+
16
GND
Power Ground
17
RXIN3-
18
RXIN3+
19
GND
Power Ground
20
NC
21
NC
22
NC
23
GND
Power Ground
24
GND
Power Ground
25
GND
Power Ground
26
VCC
27
VCC
28
VCC
29
VCC
30
VCC
www.DataSheet.co.kr
18
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
www.DataSheet.co.kr
30
VCC
NC
19
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
H-section
Item
Period
Active
Blanking
Period
Active
Blanking
Symbol
Tv
Tdisp(v)
Tblk(v)
Th
Tdisp(h)
Tblk(h)
Min
776
768
8
1440
1366
50
Typ
808
768
40
1606
1366
240
Max
1023
768
255
2047
1366
681
Clock
Period
Frequency
Tclk
Freq
F
55
12.8
78
90
Th
Th
Tclk
Tclk
Tclk
ns
MHz
50
60
75
Hz
Signal
V-section
Frame Rate
Frame Rate
Unit
Th
20
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
www.DataSheet.co.kr
21
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
www.DataSheet.co.kr
Value
Parameter
Unit
Min.
Typ.
Max.
T1
0.5
10
[msec]
T2
40
50
[msec]
T3
200
[msec]
T4
200
[msec]
T5
0.5
16
50
[msec]
T6
[msec]
T7
1000
[msec]
22
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Interface Connector
Manufacturer
/ Interface card
Signal Name
Pin#
Signal Name
NC
NC
NC
GND
RXIN0-
GND
RXIN1+
10
GND
11
RXIN2-
12
RXIN2+
13
GND
14
RXCLKIN-
15
RXCLKIN+
16
GND
17
RXIN3-
18
RXIN3+
19
GND
20
NC
21
NC
22
NC
23
GND
24
GND
25
GND
26
VCC
27
VCC
28
VCC
29
VCC
30
VCC
RXIN0+
www.DataSheet.co.kr
RXIN1-
23
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Manufacturer
YEON HO
35001HS-02L
35001WR-02LP
CN1
Connector No.
Lower
CN2
Pin No.
Input
Color
Function
Hot1
Pink
Cold1
White
Low Voltage(Lamp1)
Pin No.
Input
Color
Function
Hot1
Pink
High Voltage(Lamp2)
Cold1
White
www.DataSheet.co.kr
24
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
Required Condition
Note
Vibration Test
(Non-operation)
Shock Test
(Non-operation)
Acceleration: 50 G
Wave: Half-sine
Active Time: 20 ms
Direction: X, Y, Z (one time for each Axis)
Drop Test
On/Off Test
www.DataSheet.co.kr
Operation:10,000 ft
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20 to 60, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
25
Product Specification
M185XW01 V8
AU OPTRONICS CORPORATION
for identification.
for identification.
for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by
www.DataSheet.co.kr
26
www.DataSheet.co.kr
Ver 0.1