Escolar Documentos
Profissional Documentos
Cultura Documentos
Switched Networks
Practice Skills Assessment Packet Tracer
A few things to keep in mind while completing this activity:
Do not use the browser Back button or close or reload any exam windows during the exam.
Do not close Packet Tracer when you are done. It will close automatically.
Click the Submit Assessment button in the browser window to submit your work.
Introduction
In this practice skills assessment, you will configure the Company A network with RPVST+, port
security, EtherChannel, DHCP, VLANs and trunking, and routing between VLANs. In addition you
will perform an initial configuration on a switch, secure unused switch ports and secure SVIs. A
simple access control list will also be configured.
All IOS device configurations should be completed from a direct terminal connection to
the device console from an available host.
Some values that are required to complete the configurations have not been given to you.
In those cases, create the values that you need to complete the requirements. These
values may include certain IP addresses, passwords, interface descriptions, banner text,
and other values.
For the sake of time, many repetitive but important configuration tasks have been omitted from
this activity. Many of these tasks, especially those related to device security, are essential
elements of a network configuration. The intent of this activity is not to diminish the importance of
full device configurations.
You will practice and be assessed on the following skills:
Configuration of RPVST+
EtherChannel configuration
SW-A:
Configure EtherChannel
Configure trunking
Configure RPVST+
SW-B:
Configure EtherChannel
Configure trunking
Activate RPVST+
SW-C:
Configure EtherChannel
Configure trunking
Configure RPVST+
Internal PC hosts:
Tables
Note: You are provided with the networks that interfaces should be configured on. Unless you are
told to do differently in the detailed instructions below, you are free to choose the host addresses
to assign.
Addressing Table:
Instructions
All configurations must be performed through a direct terminal connection to the device
consoles from an available host.
Step 1: Configure initial device settings on SW-B only.
Configure the host name as SW-B. The host name must match the value in the table
exactly in spelling, case, and punctuation.
Prevent the router CLI from attempting to look up mistyped commands as URLs.
Prevent IOS status messages from interrupting command line output at the device
console.
The VLAN names must match the values in the table exactly in spelling, case, and
punctuation.
Each switch should be configured with all of the VLANs shown in the table.
All switch ports that you assign to VLANs should be configured to static access mode.
Note that all the unused ports on SW-B only should be assigned to VLAN 999. This
configuration step on switches SW-A and SW-C has been left out of this activity for the sake
of time.
Use LACP.
The switch ports on both sides of Channels 1 and 2 should both initiate negotiations for
channel establishment.
The switch ports on the SW-B side of the Channel 3 should initiate negotiations with the
switch ports on SW-C.
The switch ports on the SW-C side of Channel 3 should not initiate negotiations with the
switch ports on the other side of the channel.
SW-A should be configured as root primary for VLAN 5 and VLAN 10 using the default
primary priority values.
SW-A should be configured as root secondary for VLAN 15 and VLAN 100 using the
default secondary priority values.
SW-C should be configured as root primary for VLAN 15 and VLAN 100 using the default
configured on the switch ports. Do not use the portfast default form of the command.
Activate BPDU Guard on all access ports that are connected to hosts.
Each switch port should accept only two MAC addresses before a security action occurs.
If a security violation occurs, the switch ports should provide notification that a violation
has occurred but not place the interface in an err-disabled state.
c. On SW-B, configure the virtual terminal lines to accept only SSH connections on the virtual
terminal lines.
Configure user-based authentication for SSH connections to the vty lines with a user
name ofnetadmin and a secret password of SSH_secret9. The user name and password
must match the values provided here exactly in case, punctuation, and spelling.
Permit only addresses from the admin VLAN network to access any address on
Hosts on the admin VLAN network should be able to reach all other destinations.
Create a DHCP pool for hosts on VLAN5 using the pool name vlan5pool.
Create a DHCP pool for hosts on VLAN10 using the pool name vlan10pool.
Create a DHCP pool for hosts on VLAN15 using the pool name vlan15pool.
All VLAN pool names must match the provided values exactly.
Once they have received addresses, the hosts should be able to ping hosts on other
networks.
no shut
exit
int g0/1.15
encapsulation dot1Q 15
ip addr 10.10.15.1 255.255.255.0
no shut
exit
int g0/1.100
encapsulation dot1Q 100
ip addr 10.10.100.1 255.255.255.0
no shut
exit
int g0/1.199
encapsulation dot1Q 199
ip addr 10.10.199.1 255.255.255.0
no shut
exit
ip dhcp excluded-address 10.10.5.1 10.10.5.5
ip dhcp pool vlan5pool
network 10.10.5.0 255.255.255.0
default-router 10.10.5.1
dns-server 192.0.2.62
exit
ip dhcp excluded-address 10.10.10.1 10.10.10.5
ip dhcp pool vlan10pool
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 192.0.2.62
exit
ip dhcp excluded-address 10.10.15.1 10.10.15.5
ip dhcp pool vlan15pool
network 10.10.15.0 255.255.255.0
default-router 10.10.15.1
dns-server 192.0.2.62
exit
ip access-list standard 1
permit 10.10.100.0 0.0.0.255
exit
int g0/1.199
ip access-group 1 out
SW-B
en
conf t
hostname SW-B
no ip domain-lookup
banner motd SW-B
enable secret cisco
service password-encryption
line console 0
password cisco
login
Logging synchronous
exit
line vty 0 15
password cisco
login
exit
no logging console
vlan 5
name sales
exit
vlan 10
name prod
exit
vlan 15
name acct
exit
vlan 100
name admin
exit
vlan 199
name manage
exit
vlan 999
name null
exit
int f0/7
switchport mode access
switchport access vlan 5
no shutdown
exit
int f0/10
switchport mode access
switchport access vlan 10
no shutdown
exit
int f0/15
switchport mode access
switchport access vlan 15
no shutdown
exit
int f0/24
switchport mode access
switchport access vlan 100
no shutdown
exit
int vlan 199
ip address 10.10.199.253 255.255.255.0
ip default-gateway 10.10.199.1
int port-channel 2
exit
int range fa0/3-4
channel-group 2 mode active
exit
int port-channel 3
exit
int range fa0/5-6
channel-group 3 mode active
exit
int range fa0/3-6
switchport mode trunk
exit
spanning-tree mode rapid-pvst
int fa0/15
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky
switchport port-security violation restrict
exit
int fa0/24
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky
switchport port-security violation restrict
exit
ip domain-name ccnaPTSA.com
crypto key generate rsa
1024
ip ssh version 2
line vty 0 4
login local
transport input ssh
exit
username netadmin secret SSH_secret9
SW-A>
en
conf t
vlan 5
name sales
exit
vlan 10
name prod
exit
vlan 15
name acct
exit
vlan 100
name admin
exit
vlan 199
name manage
exit
vlan 999
name null
exit
int f0/5
switchport mode access
switchport access vlan 5
no shutdown
exit
int f0/10
switchport mode access
switchport access vlan 10
no shutdown
exit
int f0/15
switchport mode access
switchport access vlan 15
no shutdown
exit
int f0/24
switchport mode access
switchport access vlan 100
no shutdown
exit
int vlan 199
ip address 10.10.199.254 255.255.255.0
ip default-gateway 10.10.199.1
int port-channel 1
exit
int port-channel 2
exit
int range fa0/1-2
channel-group 1 mode active
exit
int range fa0/3-4
channel-group 2 mode active
exit
SW-C
en
conf t
vlan 5
name sales
exit
vlan 10
name prod
exit
vlan 15
name acct
exit
vlan 100
name admin
exit
vlan 199
name manage
exit
vlan 999
name null
exit
int f0/7
switchport mode access
switchport access vlan 5
no shutdown
exit
int f0/10
switchport mode access
switchport access vlan 10
no shutdown
exit
int f0/15
switchport mode access
switchport access vlan 15
no shutdown
exit
int f0/24
switchport mode access
switchport access vlan 100
no shutdown
exit
int vlan 199
ip address 10.10.199.252 255.255.255.0
ip default-gateway 10.10.199.1
int port-channel 1
exit
int port-channel 3
exit
int range fa0/1-2
channel-group 1 mode active
exit
int range fa0/5-6
channel-group 3 mode passive
exit
int range fa0/1-2
switchport mode trunk
exit
int range fa0/5-6
switchport mode trunk
exit
spanning-tree mode rapid-pvst
spanning-tree vlan 15 root primary