Escolar Documentos
Profissional Documentos
Cultura Documentos
Page 1 / 27
-2-
Contents
No
CONTENTS
RECORD OF REVISIONS
1
GENERAL DESCRIPTION
ELECTRICAL SPECIFICATION
3-1
ELECTRIACL CHARACTERISTICS
3-2
INTERFACE CONNECTIONS
3-3
3-4
3-5
3-6
POWER SEQUENCE
3-7
BACKLIGHT SPECIFICATION
OPTICAL SPECIFICATION
MECHANICAL CHARACTERISTICS
INTERNATIONAL STANDARD
7-1
SAFETY
7-2
EMC
PACKING
8-1
DEFINITION OF LABEL
8-2
PACKING METHODS
8-3
PRECAUTION
9-1
MOUNTING PRECAUTIONS
9-2
OPERATING PRECAUTIONS
9-3
9-4
9-5
STORAGE
9-6
Page 2 / 27
-3-
Record of Revision
Version
Date
Page
Description
0.0
2009/12/23
First release
0.1
2010/02/24 4
Electrical Characteristics
Update drawing
13
14, 15
20, 21
Update drawing
22
26, 27
0.2
2010/04/06 13
0.3
2010/04/07 16
Update CR min=1200
0.4
2010/05/12 20, 21
Update drawing
0.5
2010/09/28 14
0.6
2010/10/11 16
0.7
2010/10/25 20,21
Update drawing
0.8
2011/04/15 7
0.9
2011/06/17 4
Page 3 / 27
-4-
1. General Description
This specification is applied to the 24 inch Color TFT-LCD Module T240XW01. This LCD module has a TFT active
matrix type liquid crystal panel with 1,366x768 pixels, and the diagonal size is 24.02 inches. This module supports
1,366x768 XGA-WIDE mode (Non-interlace).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in horizontal stripes. Gray
scale or the brightness of the sub-pixel color is determined with an 8-bit gray scale signal for each dot.
The T240XW01 has been designed to apply to 8-bit and 1 channel LVDS interface method. It is intended to support
displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important.
This module is not equipped with inverter board for backlight.
* General Information
Items
Active Screen Size
Display Area
Outline Dimension
Specification
Unit
24.02
inch
mm
mm
Driver Element
Display Colors
8 bit, 16.7M
Colors
Number of Pixels
1,366 x 768
Pixel
mm
Pixel Pitch
Pixel Arrangement
Note
Without inverter
Normally Black
Surface Treatment
Anti-Glare, 3H
Haze=2%
Page 4 / 27
-5-
Item
Symbol
Min
Max
Unit
Vcc
-0.3
[Volt]
Note 1
Vin
-0.3
[Volt]
Note 1
Conditions
Operating Temperature
TOP
+50
[ C]
Note 2
Operating Humidity
HOP
10
90
[%RH]
Note 2
Storage Temperature
TST
-20
+60
[ C]
Note 2
Storage Humidity
HST
10
90
[%RH]
Note 2
PST
65
and No condensation.
[ C]
Note 3
or less. At temperatures
greater than 40
Page 5 / 27
-6-
3. Electrical Specification
The T240XW01 V1 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The second input for BLU is to power inverter.
Symbol
Value
Min.
Typ.
Max
Unit
Note
LCD
Power Supply Input Voltage
VDD
4.5
5.5
VDC
IDD
--
0.65
0.8
Power Consumption
PC
--
3.5
4.0
Watt
IRUSH
--
--
VID
200
400
600
mVDC
VTH
+100
--
+300
mVDC
VTL
-300
--
-100
mVDC
VICM
1.1
1.25
1.4
VDC
2.7
--
3.3
VDC
--
0.6
VDC
45
50
55
Watt
Inrush Current
Input Differential Voltage
LVDS
Interface
VIH
(High)
VIL
(Low)
CMOS
Interface
PBL
Note :
1.
2.
3.
GND
VDD
10%
400 s
4. VICM = 1.25V
V IC M
V TH
V TL
|V ID |
0V
Page 6 / 27
-7-
Symbol
Reserved
Description
Reserved
Reserved
GND
CH1_0-
Ground
CH1_0+
GND
CH1_1-
CH1_1+
Ground
10
GND
11
CH1_2-
Ground
12
CH1_2+
13
GND
14
CH1_CLK-
15
CH1_CLK+
16
GND
17
CH1_3-
18
CH1_3+
19
GND
20
NC
21
LVDS_SEL
22
NC
23
GND
Ground
24
GND
Ground
25
GND
Ground
26
Vdd (+5V)
27
Vdd (+5V)
28
Vdd (+5V)
29
Vdd (+5V)
30
Vdd (+5V)
Ground
Ground
Ground
No connection
Open/High(3.3V) for NS, Low(GND) for
JEIDA
No connection
Page 7 / 27
-8-
C u rren t C ycle
N e xt C ycle
C lo c k
C H x_0+
C H x_0-
R1
R0
G0
R5
R4
R3
R2
R1
R0
G0
C H x_1+
C H x_1-
G2
G1
B1
B0
G5
G4
G3
G2
G1
B1
C H x_2+
C H x_2-
B3
B2
DE
NA
NA
B5
B4
B3
B2
DE
R7
R6
NA
B7
B6
G7
G6
R7
R6
NA
C H x_3+
C H x_3-
Note: x = 1, 2, 3, 4
C u rren t C y cle
N e xt C y cle
C lo ck
C H x_0+
C H x_0-
R3
R2
G2
R7
R6
R5
R4
R3
R2
G2
C H x_1+
C H x_1-
G4
G3
B3
B2
G7
G6
G5
G4
G3
B3
C H x_2+
C H x_2-
B5
B4
DE
NA
NA
B7
B6
B5
B4
DE
R1
R0
NA
B1
B0
G1
G0
R1
R0
NA
C H x_3+
C H x_3-
Note: x = 1, 2, 3, 4
Page 8 / 27
-9-
Item
Symbol
Min.
Typ.
Max
Unit
Period
Tv
784
810
1015
Th
Active
Tdisp (v)
Blanking
Tblk (v)
16
42
247
Th
Period
Th
1460
1648
2000
Tclk
Active
Tdisp (h)
Blanking
Tblk (h)
94
282
634
Tclk
Clock
Frequency
Fclk=1/Tclk
50
80
86
MHz
Vertical Frequency
Frequency
Fv
47
60
63
Hz
Horizontal Frequency
Frequency
Fh
43
48
53
KHz
Vertical Section
Horizontal Section
768
Th
1366
Tclk
Notes:
(1) Display position is specific by the rise of DE signal only.
st
st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a Low level period equivalent to eight times of
st
st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE High is less than 1366 DCLK or less than 768 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE High and the effective data period do not
synchronize with each other.
Page 9 / 27
- 10 -
Page 10 / 27
- 11 -
RED
GREEN
MSB
BLUE
LSB MSB
LSB MSB
LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black
Red(255)
Green(255)
Basic
Blue(255)
Color
Cyan
Magenta
Yellow
White
RED(000)
RED(001)
RED(254)
RED(255)
GREEN(000)
GREEN(001)
GREEN(254)
GREEN(255)
BLUE(000)
BLUE(001)
BLUE(254)
BLUE(255)
----
----
----
Page 11 / 27
Parameter
Values
Unit
Min.
Type.
Max.
t1
0.4
---
30
ms
t2
0.1
---
50
ms
t3
200
---
---
ms
---
---
ms
---
---
ms
t4
t5
*1
t6
---
---
t7
500
---
*2
---
---
ms
ms
Note:
(1) T4=0 : concern for residual pattern before BLU turn off.
(2) T6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD operation or
the LCD turns off before the backlight turns off, the display may momentarily become abnormal.
Caution: The above on/off sequence should be applied to avoid abnormal function in the display. In case of
handling, make sure to turn off the power when you plug the cable into the input connector or pull the cable out of
the connector.
Page 12 / 27
Item
Symbol
Spec
Condition
Min.
Typ.
Max.
Unit
Note
Operating Voltage
Vo
920
1020
1120
[ Vrms ]
Operating Current
Io
14.5
15
15.5
[ mArms ]
PBL
50
[ Watt ]
At 0
2300
Striking Voltage
Vstk
At 25
[ Vrms ]
2000
Striking Time
Ts
1000
1500
[ msec ]
Operating Frequency
fo
53
55
57
[ kHz ]
F_PWM
140
180
240
[ Hz ]
D_PWM
20
100
[%]
Note
1&2
Lamp Type
U type
Number of Lamps
[ PC ]
Ta=255
Note 1: Dimming range
Page 13 / 27
Symbol
Spec
Condition
Lamp voltage
VL
Lamp current
IL
Lamp frequency
fL
Starting voltage
Vs
At 25
At 0
Min.
Typ.
Max.
920
1020
1120
15.0
Unit
Note
[ Vrms ]
[ mArms ]
40
80
[ kHz ]
2300
[ Vrms ]
2000
[ Vrms ]
TD
0.5
[ sec ]
Life time
TL
30K
[ hr ]
Unsymmetrical ratio
UR
10%
Crest factor
C.F.
1
2 10%
2 + 10%
I-p
Page 14 / 27
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable for approximately 45 minutes in a
dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of and equal to 0.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Parameter
Contrast Ratio
Surface Luminance (White)
Luminance Variation
Response Time (G to G)
Color Gamut
Values
Symbol
CR
Unit
Min.
Typ.
Max
1200
2000
--
LWH
250
300
--
WHITE(9P)
--
--
1.3
--
6.5
--
NTSC
72
RX
0.64
RY
0.33
GX
0.28
Notes
1
cd/m
2
3
Ms
Color Coordinates
Red
Green
GY
Blue
White
Typ.-0.03
0.59
BX
0.14
BY
0.06
WX
0.29
WY
0.30
Typ.+0.03
Viewing Angle
x axis, right(=0)
--
89
--
degree
x axis, left(=180)
--
89
--
degree
y axis, up(=90)
--
89
--
degree
--
89
--
degree
Page 15 / 27
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 15mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, WHITE is defined (center of Screen) as:
WHITE(9P)= Maximum(Lon1, Lon2,,Lon5)/ Minimum(Lon1, Lon2,Lon5)
is the average time required for display transition by switching the input signal for five
4. Response time T
Measured
Response Time
Target
0%
0%
Start
25%
50%
75%
100%
0% to 25%
0% to 50%
0% to 75%
0% to 100%
25% to 50%
25% to 75%
25% to 100%
50% to 75%
50% to 100%
25%
25% to 0%
50%
50% to 0%
50% to 25%
75%
75% to 0%
75% to 25%
75% to 50%
100%
100% to 0%
100% to 25%
100% to 50%
75% to 100%
100% to 75%
FIG. 2 Luminance
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG3.
Page 16 / 27
Page 17 / 27
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T240XW01 V1. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Outline Dimension
Horizontal
580.0 mm
Vertical
347.5 mm
Depth
46.7mm
Horizontal
536.1 mm
Vertical
303.3 mm
Horizontal
531.7mm
Vertical
298.9 mm
Bezel Opening
Weight
2800 g (Typ.)
Surface Treatment
Anti-Glare, 3H
Page 18 / 27
Page 20 / 28
Page 21 / 28
Qty
, 300hrs
-20, 300hrs
50, 300hrs
-5, 300hrs
Condition
60
Bandwidth: 10-300Hz,
Duration: X, Y, Z 30min
One time each direction
Shock level: 50G
Page 21 / 27
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. American National standards Institute(ANSI),
1992
(2) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment. International Special committee on Radio Interference.
(3) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment. European Committee for Electrotechnical Standardization. (CENELEC),
1998
Page 22 / 27
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
for identification.
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
:
:
:
:
QTY :
: ,
: Arial
T240XW01 VX
: (
)Verdana,
: Arial
97.24T01.XXX
:
:
: (
)Verdana,
: Arial
Page 23 / 27
654(L)x381(W)x434(H) mm
Loading Capacity5pcs/box
Carton Dimension
Page 24 / 27
Item
Qty.
Dimension
Packing Remark
Weight (kg)
Packing BOX
21kg
Pallet
15kg
Total Weight
30 Boxes / Pallet
645kg
PET Strap
Angle Protector
Label
Stretch Film
Wooden Pallet
Page 25 / 27
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
Page 26 / 27
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
Page 27 / 27