Escolar Documentos
Profissional Documentos
Cultura Documentos
42CrMo4
Page 1(3)
EN 10083-3:2006
42CrMo4
Hofors designation
327A
Imatra designation
MoC410 M
Smedjebacken designation
42CrMo4
General
42CrMo4 is a steel for quenching and tempering, which has a good combination of strength and
toughness in the quenched and tempered condition. After oil quenching it will be through hardened up to
60 mm bar diameter. The micro structure of bigger dimensions is not fully martensite. The steel is
applicable to induction hardening. The surface hardness will exceed min. 53 HRC. 42CrMo4 can be
delivered M-treated in order to optimise the machinabilty.
Standard
This product specification is based on EN 10083-3:2006 and the steel will meet the requirements of this
standard.
The steel can also be delivered according to following European Standards:
EN 10250-3 Open die steel forgings for general engineering purposes. Part 3: Special alloy steels
EN 10263-4 Steel rod, bars and wire for cold heading and cold extrusion
EN 10269 Steels for fasteners with specified elevated and/or low temperatures properties
EN 10277-5 Bright steel products. Steels for quenching and tempering
EN 10297 Seamless circular steel tubes for mechanical and general engineering purposes
EN 10305 Seamless cold drawn tubes for precision applications
prEN 10343 Steels for quenching and tempering for construction purposes
Chemical composition
C%
Si%
Mn%
min.
0,38
0,15
0,60
max.
0,45
0,40
0,90
P%
S%
0,025
0,035
Cr%
Mo%
0,90
0,15
1,20
0,30
Mechanical properties
Condition
As rolled
Bar
diameter
mm
Yield
strength
Re min.
MPa
Tensile
strength
Rm
MPa
Elon- Reduction
gation of area Z
A5 min.
min.
%
%
Impact strength
KV min.
J
Hardness
HBW
T C
...350a
25...180
Annealed
Quenched
and
tempered
...241
25...40
750
1000...1200
11
45
35
20
300...350a
>40...100
650
900...1100
12
50
35
20
270...320a
>100...160
550
800950
13
50
35
20
240...280a
>160180
500
750...900
14
55
35
20
220270a
a
Informative
PRODUCT SPECIFICATION
42CrMo4
EN 10083-3:2006
42CrMo4
Hofors designation
327A
Imatra designation
MoC410 M
Smedjebacken designation
42CrMo4
Page 2(3)
1 050...850
Annealing
Stress relieving
Hardening
Cooling
In air
680720
450...650
In air
840880
Tempering
540...680
In air
Stress relieving after induction
150180
In air
hardening
b
The temperature of stress relieving must chosen approx. 50C below the tempering temperature.
Welding
The steel has a restrictive weldability. For instructions regarding filler metals, working temperature and
post heat treatments please contact to our technical customers service.
Tempering diagram
MPa
1400
J, %, HRC
100
90
1200
80
1000
70
800
600
400
200
0
400
60
HBW
50
500
40
400
30
300
20
200
10
450
500
550
0
600
650
700
Tempering temperature C
The values are informative. They are based on oil quenching with a 60 mm probe.
PRODUCT SPECIFICATION
42CrMo4
Page 3(3)
EN 10083-3:2006
42CrMo4
Hofors designation
327A
Imatra designation
MoC410 M
Smedjebacken designation
42CrMo4
Hardenability
The hardenability will be calculated from the actual analysis according to Ovako formula JoD. If agreed
at the time of enquiry and order, the hardenability can be verified with a end quench test.
20
HRC
40
60
75
90
100
65
60
Bar diameter, mm
(oil quenching)
HH
55
50
45
40
35
HL
30
25
20
0
10
20
30
40
50
The hardenability of 42CrMo4 varies within the limits of the scatter band. Quenched from
850 C. The hardness of an oil quenched piece (at 1/3 radius) can be estimated using the bar diameter
scale of the diagram.
Bar diameter
mm
50
+QT
25...60
720
The table is based on EN 10269 +A1.
C
100
702
150
677
200
640
250
602
300
562
350
518
400
475
450
420
500
375
Minimum impact energy (J) at low temperature with ISO-V test pieces
Condition
Bar diameter
mm
+QT
25...60
The table is based on EN 10269 +A1.
C
-100
27
-50
-40
40
-20
+20
50
Disclaimer
This specification is for information purposes only. Ovako takes no responsibility for the
suitability of the steels referred to in this specification to a given product or end use. We reserve
the right to change or correct the data in this specification without prior notification. Ovako takes
no responsibility for any errors in this information, or for any consequences resulting from its
use