Escolar Documentos
Profissional Documentos
Cultura Documentos
Rev. 1.0
APR 2012
Rev. 1.0
APR 2012
Revision History
Rev. 1.0
Date
Revision
APR 2012
1.0
History
New Creation
APR 2012
2. System Features
Voltage range:
High Voltage SD Memory Card Operating voltage range: 2.7-3.6 V
(1) Default Speed mode: 3.3V signaling, Frequency up to 25 MHz, up to 12.5 MB/sec
(2) High Speed mode: 3.3V signaling, Frequency up to 50 MHz, up to 25 MB/sec
(3) SDR12: 1.8V signaling, Frequency up to 25 MHz, up to 12.5MB/sec
(4) SDR25: 1.8V signaling, Frequency up to 50 MHz, up to 25MB/sec
(5) SDR50: 1.8V signaling, Frequency up to 100 MHz, up to 50MB/sec
(6) SDR104: 1.8V signaling, Frequency up to 208 MHz, up to 104MB/sec
(7) DDR50: 1.8V signaling, Frequency up to 50 MHz, sampled on both clock edges, up to 50MB/sec
Rev. 1.0
APR 2012
Five Speed Classes are defined and indicate minimum performance of the cards
Class 0 - These class cards do not specify performance. It includes all the legacy cards prior to
this specification, regardless of its performance
Rev. 1.0
APR 2012
to 85
Storage: -40(168h) to 85(500h)
Operating: -25
Durability
Bending
10N
Torque
0.10N*m. 2.5
Drop Test
max
smoothness
MTBF
>1,000,000 hours
Preventive Maintenance
None
Data Reliability
Endurance
Rev. 1.0
APR 2012
Name
DAT2
CD/DAT3
CMD
VDD
CLK
Vss
DAT0
DAT1
Type
I/O
I/O
PP
S
I
S
I/O
I/O
Micro SD Description
Card Detect/ Data Lin [Bit 3]
Card Detect / Data Line
Command / Response
Supply voltage
Clock
Supply voltage ground
Data Line [Bit 0]
Data Line [Bit 1]
Note:
1) S=power supply; I=input; O=output using push-pull drivers.
2) The extended DAT lines (DAT1-DAT3) are input on power up; they start to operate as DAT lines after the
SET _BUS_WIDTH command.
3) After power up, this line is input with 50Kohm pull-up (can be used for card detection or SPI mode selection).
The pull-up should be disconnected by the user, during regular data transfer, with SET_CLR_CARD_DETECT
(ACMD42) command.
Name
Type
Micro SD Description
1
2
3
4
5
6
7
8
RSV
CS
DI
VDD
SCLK
VSS
DO
RSV
I
S
S
I
S
O
I
Reserved
Chip Select (neg true)
Data In
Supply Voltage
Clock
Supply Voltage Ground
Data Out
Reserved
Width
Description
CID
128
RCA
16
CSD
128
SCR
64
OCR
32
The host may reset the cards by switching the power supply off and on again. The card has its own power-on
detection circuitry which puts the card into an idle state after the power-on. The card can also be reset by sending the
GO_IDLE (CMD0) command.
Rev. 1.0
APR 2012
CMD: Command is bi-directional signal.(Host and card drivers are operating in push pull mode.)
DAT0-3: Data lines are bi-directional signals. (Host and card drivers are operating in push pull mode.).
CLK: Clock is a host to cards signal. (CLK operates in push pull mode.)
VDD: VDD is the power supply line for all cards.
VSS [1:2]: VSS are two ground lines.
The following figure shows the bus topology of several cards with one host in SD Bus mode.
Rev. 1.0
APR 2012
Rev. 1.0
APR 2012
Rev. 1.0
10
APR 2012
Rev. 1.0
11
APR 2012
Rev. 1.0
12
APR 2012
Rev. 1.0
13
APR 2012
Rev. 1.0
14
APR 2012
Rev. 1.0
15
APR 2012
SYMBOL
A
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
B
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
C
C1
C2
C3
D1
D2
D3
R1
R2
R3
R4
R5
R6
R7
R10
R11
R17
R18
R19
R20
aaa
MIN
10.90
9.60
7.60
0.75
0.90
0.60
0.80
1.35
6.50
0.50
0.40
14.90
6.30
1.64
1.30
0.42
2.80
5.50
0.20
1.00
7.80
1.10
3.60
2.80
8.20
0.90
0.60
0.20
0.00
1.00
1.00
1.00
0.20
0.20
0.70
0.70
0.60
0.60
29.50
0.10
0.20
0.05
4
133
NOM
11.00
9.70
3.85
7.70
1.10
0.80
0.70
1.40
6.60
0.55
0.45
15.00
6.40
1.84
1.50
0.52
2.90
0.30
1.10
7.90
1.20
3.70
2.90
1.00
0.70
0.30
0.40
0.40
0.80
0.80
0.80
0.80
30.00
0.20
0.20
0.20
0.40
135
MAX
11.10
9.80
7.80
0.85
8.50
0.80
1.45
6.70
0.60
0.50
15.10
6.50
2.04
1.70
0.62
3.00
0.40
1.20
9.00
8.00
1.30
3.80
3.00
6.20
1.10
0.80
0.40
0.15
0.60
0.60
0.90
0.90
0.90
0.90
30.50
0.30
0.60
0.20
0.15
137
0.10
Notes
NOTE
1. DIMENSIONING AND TOLERANCING
PER ASME Y14.5M - 1994.
BASIC
2. DIMENSIONS ARE IN MILLIMETERS.
BASIC
3. COPLANARITY IS ADDITIVE TO C1 MAX
THICKNESS.
4. ALL EDGES SHALL NOT BE SHARP AS
TESTED PER UL1439 "Test for Sharpness
of Edges on Equipment."
5. Refer to Appendix E about test method of
warpage.
Rev. 1.0
16
APR 2012