Escolar Documentos
Profissional Documentos
Cultura Documentos
Pipe Body:
Tubular Assembly:
Nominal
100% RBW
95% RBW
Ultra Class
90% RBW
Premium
80% RBW
5.500
0.361
4.778
5.464
0.343
4.778
5.428
0.325
4.778
5.356
0.289
4.778
611,962
70,994
579,322
67,147
546,897
63,334
482,692
55,809
12,061
10,753
13,094
9,800
12,405
8,835
11,027
6,865
OD (in):
Wall Thickness (in):
Nominal ID (in):
18
0
Maximum MUT is higher than 80% RBW pipe body torsional strength. A reduced MUT is recommended.
Notes: Body properties are calculated based on uniform OD and wall thickness.
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API.
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of 4.72'',
which is smaller than pipe purchased at 87.5%.
Connection: TT550
TJ OD (in): 6.625
TJ ID (in): 4.250
MYS (ksi): 130
Elevator Shoulder:
Optimum MUT (ft-lbs):
Tension @ Optimum MUT (lbs):
50,800
843,100
59,200
Tensile Limited
633,600
42,400
1,040,800
1,046,600
N/A
N/A
Note: Elevator capacity based on assumed elevator bore, no wear factor, and contact stress of 110, 100 psi. An increased
elevator shoulder OD increases elevator capacity without affecting make-up torque.
The technical information containted herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com
Download the Workstrings International Pipe Specification App on the App Store or Google Play
03-Mar-16
TurboTorque 550
80 % Inspection Class
Tool Joint OD
(in)
6.625
Tool Joint ID
Pipe Body OD
(in)
5.5
(in)
0
2,700
5,300
8,000
10,700
13,400
16,000
18,700
21,400
24,100
26,700
29,400
32,100
34,800
37,400
40,100
42,800
45,500
48,100
50,800
(lbs)
482,700
482,100
480,500
477,700
473,700
468,600
462,400
454,800
445,800
435,400
423,900
410,300
394,900
377,400
358,300
335,700
309,800
279,500
244,800
199,900
TSS-105
(ft-lbs)
Connection Max
Pipe Body
Max Tension Tension
(lbs)
(ft-lbs)
4.250
Operationa Assembly
l Torque
Max Tension
(ft-lbs)
(lbs)
(ft-lbs)
Connection
Pipe Body
Max Tension Max Tension
(lbs)
(lbs)
(lbs)
482,700
633,600
482,700
482,700
1,040,800
482,100
633,600
2,000
482,400
482,400
1,040,800
480,500
633,600
4,000
481,500
481,500
1,040,800
477,700
633,600
6,100
479,800
479,800
1,040,800
473,700
633,600
8,100
477,600
477,600
1,040,800
474,700
474,700
1,040,800
471,200
471,200
1,040,800
466,800
466,800
1,040,800
461,900
461,900
1,040,800
456,300
456,300
1,040,800
1,040,800
468,600
462,400
454,800
445,800
435,400
423,900
410,300
394,900
377,400
358,300
335,700
309,800
279,500
244,800
199,900
10,100
633,600
12,100
633,600
14,200
633,600
16,200
633,600
18,200
633,600
633,600
20,200
450,000
450,000
633,600
22,300
442,500
442,500
1,040,800
633,600
24,300
434,500
434,500
1,040,800
633,600
26,300
425,700
425,700
1,040,800
633,600
28,300
416,000
416,000
1,040,800
633,600
30,400
404,800
404,800
1,040,800
633,600
32,400
393,000
393,000
1,040,800
633,600
34,400
380,100
380,100
1,040,800
633,600
36,400
365,900
365,900
1,040,800
633,600
38,400
349,900
349,900
1,040,800
Connection
Make-up Torque Range
Make-up Torque
(ft-lbs)
Min MUT
Max MUT
42,400
43,300
44,300
45,200
46,100
47,100
48,000
48,900
49,900
50,800
Connection Max
Tension
(lbs)
1,040,800
1,030,100
1,005,200
982,800
960,300
935,400
912,900
890,500
865,500
843,100
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
06-22-2015