Escolar Documentos
Profissional Documentos
Cultura Documentos
Fasteners
Institute
All rights reserved, in particular rights of translation into other languages. No part of
this publication may be reproduced or transmitted in any form or by any means, electronic, microfilm, mechanical, photocopying, recording, or otherwise without the prior
written permission of the publisher.
PRINTED IN CANADA
TABLE OF CONTENTS
THREAD SECTION
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
17
ASME B1.2 Gages and Gaging for Unified Inch Screw Threads
54
ASME B1.3 Screw Thread Gaging Systems for Acceptability: Inch and
Metric Screw Threads (UN, UNR, UNJ, M, and MJ)
65
IFI-301 Gage Calibration Requirements and Procedures for Thread Gages
73
178
222
ASTM A193/A193M Alloy Steel and Stainless Steel Bolting Materials for
High Temperature Service 234
ASTM A307 Carbon Steel Externally Threaded Standard Fasteners
248
ASTM A320/A320M Alloy Steel Bolting Materials for Low Temperature Service
257
ASTM A354 Quenched and Tempered Alloy Steel Bolts, Studs, and Other
Externally Threaded Fasteners 267
ASTM A394 Steel Transmission Tower Bolts, Zinc Coated and Bare
277
ASTM A449 Hex Cap Screw, Bolts and Studs, Steel, Heat Treated, 120/105/90
ksi Minimum Tensile Strength, General Use
287
TABLE OF CONTENTS
ASTM A962/A962M Common Requirements For Bolting Intended For Use At Any
Temperature From Cryogenic To The Creep Range
299
ASTM F468 Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
317
ASTM F593 Stainless Steel Bolts, Hex Cap Screws, and Studs
331
ASTM F1554 Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength
344
367
SOCKET SECTION
ASME B18.3 Socket Cap, Shoulder, Set Screws, Hex, and Spline Keys
413
469
478
ASTM F879 Stainless Steel Socket Button and Flat Countersunk Head Cap Screws
489
515
ASTM A325 Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
532
ASTM A490 Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
544
ASTM F959 Compressible-Washer-Type Direct Tension Indicators for Use with Structural
Fasteners 554
ASTM F1852 Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies,
Steel, Heat Treated 120/105 ksi Minimum Tensile Strength
561
ASTM F2280 Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies,
Steel, Heat Treated, 150 ksi Minimum Tensile Strength
572
TABLE OF CONTENTS
NUT SECTION
ASME B18.2.2 Nuts for General Applications: Machine Screw Nuts, Hex, Square,
Hex Flange, and Coupling Nuts 585
ASME B18.6.9 Wing Nuts 607
ASME B18.16.4 Serrated Hex Flange Locknuts: 90,000 psi
616
636
ASTM A194/A194M Carbon and Alloy Steel Nuts for Bolts for High Pressure or
High Temperature Service, or Both 644
ASTM A563 Carbon and Alloy Steel Nuts 657
ASTM F467 Nonferrous Nuts for General Use 668
ASTM F594 Stainless Steel Nuts 678
IFI-101 Torque-Tension Requirements for Prevailing-Torque Type Steel Hex
and Hex Flange Nuts 689
IFI-155 Test Procedure for the Performance of Nonmetallic Resistant Element
Prevailing-Torque Nuts 692
IFI-160 Test Procedure for the Performance of Nuts with Pre-Applied Adhesive
Coated Threads 696
SCREW SECTION
ASME B18.6.1 Wood Screws 703
ASME B18.6.2 Slotted Head Cap Screws 716
ASME B18.6.3 Machine Screws, Tapping Screws, and Metallic Drive Screws
731
822
TABLE OF CONTENTS
ASTM C1513 Steel Tapping Screws for Cold-Formed Steel Framing Connections
863
WASHER SECTION
ASME B18.21.1 Washers: Helical Spring-Lock, Tooth Lock and Plain Washers
873
RIVET SECTION
ASME B18.1.1 Small Solid Rivets 7/16 In. Nominal Diameter and Smaller
905
ASME B18.1.2 Large Rivets 1/2 In. Nominal Diameter and Larger
917
ASME B18.7 General Purpose Semi-Tubular Rivets, Full Tubular Rivets, Split
Rivets and Rivet Caps 930
IFI-110 Glossary of Terms Relating to Blind Rivets
943
968
987
993
1003
PIN SECTION
ASME B18.8.1 Clevis Pins and Cotter Pins 1007
ASME B18.8.2 Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins
1016
FINISHES SECTION
ASTM B695 Coatings of Zinc Mechanically Deposited on Iron and Steel
1059
TABLE OF CONTENTS
ASTM F1941 Electrodeposited Coatings on Threaded Fasteners
1068
ASTM F2329 Zinc Coating, Hot-Dip, Requirements for Application to Carbon and
Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
1080
QUALITY SECTION
ASME B18.2.9 Gage and Gaging for Bolts and Screws
1089
1103
ASTM F606 Standard Test Methods for Determining the Mechanical Properties of Externally
and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
1139
ASTM F788/F788M Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
1164
1172
ASTM F1470 Standard Guide for Fastener Sampling for Specified Mechanical Properties
and Performance Inspection 1178
IFI-143 Test for Evaluating the Torque-Tension Relationship on Both Externally and Internally
Threaded Fasteners 1184
REFERENCE SECTION
Standards References 1191
INDEX 1209