Escolar Documentos
Profissional Documentos
Cultura Documentos
Seamless Tubing in Titanium Grade 1/UNS R50250, Grade 2/R50400, Grade 5/R56400, Grade 7/R52400, Grade 9/R56320 & Grade
12/R53400
Seamless Tubing in Duplex UNS S31803 & S32205
Seamless Tubing in Super Duplex UNS S32750 & S32760
Seamless Tubing in 6 Moly UNS S31254, N08925 & N08926
Seamless Tubing in Copper Nickel UNS C70600 C70620 C7060X C7150 C71520 C71640
Welded Tubing in Duplex UNS S31803 & S32205
Welded Tubing in Super Duplex UNS S32750 & S32760
Welded Tubing in 6 Moly UNS S31254, N08926 & N08925
Welded Tubing in Copper Nickel UNS C70600 C70620 C7060X C7150 C71520 C71640
Elbows
150#
300#
6000#
9000#
Socket Weld
Fittings
Threaded
Fittings
Tees
Couplings
End Caps
Concentric & Eccentric Swage Nipples
Flanges
PM is the US agent for Hans van Triel flanges. Read more <here>.
Flanges in Duplex - UNS S31803 & S32205
Flanges in Super Duplex - UNS S32750 & S32760
Flanges in 6 Moly - UNS S31254, N08925 & N08926
Flanges in Copper Nickel UNS C70600 C70620 C7060X C7150 C71520 C71640
<Maximum Pressures>
Slip-On Flanges
Slipped over pipe and then welded both inside and outside to provide sufficient strength and
prevent leakage. Used in preference to weld necks due to lower cost and less accurate
requirements when cutting the pipe to length.
Blind Flanges
Without a bore, the blind flange is used to shut off a piping system or vessel opening. Permits
easy access for inspection purposes. Can be supplied with or without hubs at the
manufacturers option.
Weld-Neck Flanges
Designed to be joined to a piping system with butt welding. Although relatively expensive due
to long neck, preferred for high stress applications. The bore of the flange matches the bore of
the pipe, reducing turbulence and erosion.
Threaded Flanges
Similar to slip-on but bore is threaded enabling assembly without welding which obviously
limits use to relatively low pressure systems. May be welded along joint after assembly, but
not considered satisfactory method of increasing applications.
Lap-Joint Flanges
Similar to slip-on flange, but has a radius at the intersection of the bore and the flange face to
accommodate a lap stub end. Face on stub end forms the gasket face of the flange. Used when
sections of piping needs to be dismantled quickly and easily for inspection or replacement.
Orifice Flanges
Provides access for metering off gases or liquids. Clamps between a pair of flanges when
installed in line and is referred to as an orifice flange union. Jack-screws facilitate removal of
orifice plate.
Spectacle Blank
Also called a Figure 8 Blank, the Spectacle Blank is a pressure retaining plate with one solid
end and one open end connected with a web or tie-bar. Open end forms seal between two
flanges for normal flow of fluid through pipe work, and swinging solid end into position halts
flow.
150
300
400
600
900
1500
2500
1125
1500
2225
3350
5575
9275
-20 to 100
285
740
990
1480
2220
3705
6170
200
260
675
900
1350
2025
3375
5625
300
230
655
875
1315
1970
3280
5470
400
200
635
845
1270
1900
3170
5280
500
170
600
800
1200
1795
2995
4990
600
140
550
730
1095
1640
2735
4560
650
125
535
715
1075
1610
2685
4475
700
110
535
710
1065
1600
2665
4440
750
95
505
670
1010
1510
2520
4200
800
80
410
550
825
1235
2060
3430
850
65
270
355
535
805
1340
2230
900
50
170
230
345
515
860
1430
950
35
105
140
205
310
515
860
1000
20
50
70
105
155
260
430