Escolar Documentos
Profissional Documentos
Cultura Documentos
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the products serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
MOTORCYCLE LIFT
ITEM 91746
ITEM 68892
Visit our website at: http://www.harborfreight.com
Email our technical support at: tech@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. Ifanypartsaremissingorbroken,
please call 1-800-444-3353 as soon as possible.
Copyright 2011 by Harbor Freight Tools. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools. Diagrams
within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
Table of Contents
Important Safety Instructions...................... 2
Specifications.............................................. 3
Assembly Instructions................................. 3
Operating Instructions................................. 5
Warranty............................................................. 11
Page 2
16. Stay alert. Watch what you are doing, and use
common sense when operating. Do not use while
tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while
operating may result in serious personal injury.
17. Store idle lifts out of the reach of children
and do not allow persons unfamiliar with
the lift or these instructions to operate it.
Liftsaredangerous in the hands of untrained users.
18. Have your lift serviced by a qualified
repair person using only identical
replacement parts. This will ensure that
the safety of the lift is maintained.
SKU 68892
Save these
instructions.
Specifications
Max. Load Capacity
1000 LBS.
29-1/2 IN.
7 IN.
Ram Travel
3-7/8 IN.
Platform Dimensions
Assembly Instructions
Read the entire Important Safety Instructions section at the beginning of this manual
including all text under subheadings therein before setuporuseofthis product.
Unpacking
When unpacking, make sure the
following parts are included:
1. Main Lift Assembly
2. Hardware Kit
3. Lift Foot Pedal
4. Release Foot Pedal
5. Access Panel
6. Vise Assembly
7. Locking Bar
8. Ramp
SKU 68892
Page 3
Figure 1
Base Plate
(49A)
Cotter
Pin (47)
Front
Wheel (44)
Washer (43)
Figure 2
Nut (21)
Lock
Washer (20)
Washer (13)
Frame
Assembly
Lifting
Screw
(18)
Caster (14)
Washer (13)
Bolt (12)
Figure 3
Access
Panel (36)
Platform (35)
Washers (23)
Page 4
Ramp
(37)
R-pins
(04)
SKU 68892
Figure 4
Operating Instructions
Read the entire Important Safety Information section at the beginning of this manual
including all text under subheadings therein before setuporuseofthis product.
Lifting
1. Position the lift on a flat, level, hard surface
able to support at least 1350 lb.
2. Turn the Lifting Screws (18) clockwise to evenly raise
the Casters (14) off the ground and limit movement.
3. With the Access Panel (36) in place, roll the
motorcycle onto the lift. Kick the center stand of
the motorcycle down to stabilize it on the lift.
4. Clamp the front wheel of the motorcycle into the
Vise Assembly to prevent movement of the wheel.
SKU 68892
Page 5
Lifting (continued)
7. When the platform has been raised to the working
height, pass the Locking Bar (22) through the holes
in the Front Lifting Arm (38) so the lift cannot be
accidentally lowered.
Figure 5
Lifting
Screw (18)
8. Gently press Release Foot Pedal (10) to lower the
platform to rest the load on Locking Bar (22) and not
on the lift jack.
Caster (14)
Lowering
1. Remove all tools, parts, etc. from under the vehicle.
2. Slightly raise the platform to free the Locking Bar.
3. Remove the Locking Bar (22), then slowly press the
Release Foot Pedal (10) to ease down the unit.
NOTE: The speed of lowering is controlled by
the Release Foot Pedal (10). Operate this pedal
slowly in a controlled and safe manner.
Page 6
SKU 68892
Maintenance AndServicing
Procedures not specifically explained in this manual must
be performed only by a qualifiedtechnician.
Bleeding
Note: If the Lift appears not to be working
properly, it may be necessary to bleed
trapped air from its hydraulic system.
1. Check oil level. Replace plug.
SKU 68892
Page 7
Description
Hydraulic Pump
Link
Pin
R-Pin
Release Valve Spindle
Link
Pin
Pump Piston Spindle
Release Foot Pedal
Lift Foot Pedal
Bolt M6*16
Washer 6
Caster
Bolt M12*70
Washer 12
Bushing
Lifting Screws
Lock Washer 6
Nut M6
Locking Bar
Washer 10
Lock Washer 12
Nut M12
Spring
Bushing
Qty
1
1
1
5
1
1
2
1
1
1
8
17
2
4
8
4
2
9
9
1
6
8
8
1
4
Part
29
30
31
32
33
34
35
36
37
38
39
40
41
43
44
47
48
49a
53
54
55
56
57
58
59
Description
Bolt M12*65
Nut M10
Lock Washer 10
Stop Plate
Bolt M10*25
Vise
Platform
Access Panel
Ramp
Front Lifting Arm
Rear Lifting Arm
Lifting Arm Spindle
Bolt M8*12
Washer 13.5
Front Wheel
Cotter Pin
T-Connector
Base Plate
Bolt M6*30
Set Screw M8*12
U-Clamp
Nut M8
Grease Fitting
Pump Shaft
Set Screw (M6*10)
Qty
4
4
4
1
4
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
2
8
7
2
2
Page 8
SKU 68892
Page 9
P01a
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14
P15
P16
P17
P18
Page 10
Description
Base
Steel Ball
Spring
Screw
Copper Washer
Regulating Plug
Sealing Ring
Pump Piston
Union Nut
Union Nut
Screw
Spring
Release Valve
O-Ring
Steel Ball
Steel Ball
Ball Cup
Spring
Qty
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Part
P19
P20
P21
P22
P23
P24
P25
P27
P28
P29
P30
P31
P32
P33
P34
P35
P36
Description
Screw
O-Ring
Screw
Screw Protector
Oil Plug
Sealing Ring
Set Nut
Nylon Ring
Reservoir
Nylon Ring
Cylinder
O-Ring
Nylon Ring
Piston Rod
Nylon Ring
Top Nut
O-Ring
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SKU 68892
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other
warranties, express or implied, including the warranties of merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
SKU 68892
Page 11
3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 (800) 444-3353