Escolar Documentos
Profissional Documentos
Cultura Documentos
PRODUCT DATA
FEATURES
C437 models have direct- and reverse-acting (spst)
switching.
Pressure ranges: 1/2 to 5-1/2 in. of water (0.1 to 1.4
kPa); 1 to 26 in. of water (0.5 to 7 kPa); 1/2 to 5 psi (3 to
35 kPa); 1 to 10 psi (5 to 70 kPa).
Models intended for lockout applications must be
manually reset before resuming operation.
Trip-free mechanism on manual reset models ensures
that the limit function of the switch cannot be defeated
by jamming the reset lever.
External manual reset button on side of lockout
models.
Enclosed setting impedes tampering and provides
dust-resistant operation.
Buna-N fiber-reinforced material for increased
strength of control diaphragm.
Two Buna-N fiber-reinforced seal-off diaphragms for
added reliability.
APPLICATION
Main control diaphragm completely enclosed a leakproof chamber can be vented to a safe area.
Contents
Application ........................................................................
Features ...........................................................................
Specifications ...................................................................
Ordering Information ........................................................
Installation ........................................................................
Wiring ...............................................................................
Setting and Checkout .......................................................
1
1
2
2
4
5
5
68-0286
SPECIFICATIONS
Table 1. Models.
Manual Reseta
(Locks Out on Switch Break)
Switch Action
(Response at Setpoint to Pressure Change)
Model Number
C437D
Yes
C437E
Yes
Designated Manual Reset 2; the trip-free reset mechanism does not permit the switch to function as an automatic-reset device
when the manual reset lever is held in the Reset position.
Table 2. Switch Ratings (In Amperes).
C437D,E
Voltage
Full Load
Locked Rotor
Resistive Load
120 Vac
8.0
48.0
10.0
240 Vac
5.1
30.6
5.0
Switch:
Snap Switch (spst).
Differentials:
Fixed, nominal; measured at pressure indicated in Table 3.
Table 3. Pressure Differentials.
Pressure Rangea
1/2 to 5-1/2
in. (0.1 - 1.4 1 to 26 in.b 1/2 to 5 psi (3
kPa)
1 to 10 psi (5 (0/5 - 7 kPa)
- 35 kPa)
Differential Differential Differential
70 kPa)
Measured Measured at Measuremen Differential
at 1/2 in.
15 in.
t at midscale Measurement
Model Numbers
in.
kPa
in.
kPa
psi
kPa
psi
Typea
kPa
C437D
1-3/4 0.44
1/2
3.45
1c
6.89c
Subtractivec
C437E
0.25
0.06
1-1/4 0.31
1/4
1.72
1/2
3.45
Additived
a in.
= inches of water.
orifice in inlet pressure channel to compensate for momentary surges in gas pressure.
c Subtractive models: switching action occurs on pressure rise to the setpoint.
d Additive models: switching action occurs on pressure fall to the setpoint.
b Restrictive
ORDERING INFORMATION
When purchasing replacement and modernization products from your TRADELINE wholesaler or distributor, refer to the
TRADELINE Catalog or price sheets for complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).
2. Honeywell Customer Care
1885 Douglas Drive North
Minneapolis, Minnesota 55422-4386
In CanadaHoneywell Limited/Honeywell Limite, 35 Dynamic Drive, Toronto, Ontario M1V 4Z9.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
68-0286
Approvals:
Underwriters Laboratories Inc. Listed: File No. MP2168, Guide
No. MFHX.
Canadian Standards Association Certified: File No. LR95329,
Certificate No. 1736842.
Factory Mutual Approved: Report No. 3024921.
psi
kPa
3.0
20.7
1 to 26 in. of water
5.0
34.5
1/2 to 5 psi
15.0
103.4
1 to 10 psi
30.0
206.8
Replacement Parts:
106729 Cover Glass, 6 in. (152.4 mm) diameter.
118733-21 Retaining Clip.
Accessories:
4074BWK Bag Assembly: Contains two 137755 Mounting
Brackets and four self-tapping screws: for surface
mounting. Mounting brackets are shown by dashed lines in
Fig. 1.
Field-addable Orifices:
124674: 0.011 in. (0.28 mm) diameter.
122160: 0.018 in. (0.46 mm) diameter.
Pipe Connections:
Main or High Pressure: 1/2 in. NPT, female.
Vent or Low Pressure: 1/8 in. NPT, female.
Electrical Wiring: Hole tapped for 1/2 in. conduit.
Maximum Ambient Temperature: 125F (52C).
Minimum Temperature: 32F (0C).
6-1/4 (158.8)
5/16 (7.9) (4)
6-1/2
(165.1)
5/8
(15.9)
(4)
7-3/4
(196.9)
7-11/16
DIA.
(195.3)
45
45
1/8
(3.2)
1
(25.4)
1-5/16
(33.3)
7-3/8 (187.3)
1/827 NPT
1/214 NPT
2 (50.8)
3-7/16 (87.3)
M7192A
Fig. 1. Installation dimensions of the C437 gas pressure switches, in in. (mm).
RECYCLE NOTICE
68-0286
INSTALLATION
When Installing this Product
1.
2.
3.
4.
Mounting
WARNING
1.
2.
3.
IMPORTANT
To avoid leaks and case damage, use a parallel jaw
wrench on the hexagonal part of the case close to the
pipe. Carefully make all connections and test for
leakage. Do not tighten the pressure switch by
holding the case.
4.
5.
IMPORTANT
1. Remove the dust-seal label from the vent tapping
before mounting.
2. Use pipe compound sparingly to avoid clogging the
hole in the pie or diaphragm fitting.
3. Do not hand tighten the pressure switch by holding
the case.
Follow local codes or ordinances in all cases when different
from these recommendations.
b. Differential-pressure applications:
(1) Connect the high-pressure side of the system to
the 1/2 in. NPT main pressure tapping on the gas
pressure switch.
(2) Connect the low pressure side to the 1/8 in. NPT
vent tapping.
Location
Mount the gas pressure switch downstream from the pressure
regulator. Mount low gas pressure switches upstream of any
shutoff valve. Mount high gas pressure switches just upstream
from the burner.
WARNING
PRESSURE SETTING
INDICATOR
SETTING
SCREW
UNDER
RETAINER
MANUAL
RESET
BUTTON
(CC437D,
E,J,K)
TERMINAL
STRIP
VENT
TAPPING 1
(ON SIDE
NOT SHOWN)
WARNING
RETAINER
LEVELING
PENDULUM
CONDUIT
TAPPING
LENS GASKET
(G,H ONLY)
6.
M7630A
68-0286
WARNING
SCALEPLATE
WIRING
switch will not be reset until you release the manual reset
button. This prevents the switch from becoming an automaticreset device if the reset button is stuck, held in, or tied down.
WARNING
Checkout
Adjust the setpoint for normal operation and check to see that
the gas pressure switch performs as intended. Use a
manometer or accurate pressure gauge connected upstream
from the switch to measure the actual pressure.
2.
C437D
PRESSURE
RISE
TERMINAL
STRIP
SUBTRACTIVE
DIFFERENTIAL
1
SET POINT MINUS
DIFFERENTIAL (SWITCH MAKES)
M23673
C437E
PRESSURE
FALL
2
SET POINT PLUS
DIFFERENTIAL (SWITCH MAKES)
ADDITIVE
DIFFERENTIAL
SET POINT
(SWITCH BREAKS, LOCKS OUT)
Setting
M22763
2.
3.
68-0286
MAIN PRESSURE
TAPPING
PRESSURE
ORIFICE
(SELECTED)
68-0286
M7191A
68-0286
35 Dynamic Drive
customer.honeywell.com
U.S. Registered Trademark
2006 Honeywell International Inc.
68-0286 M.S. 10-06